This patch is a follow up to patch 1 regarding "Selective Sub Address
matching with call user data". It allows use of the Fast-Select-Acceptance
optional user facility for X.25.
This patch just implements fast select with no restriction on response
(NRR). What this means (according to ITU-T Recomendation 10/96 section
6.16) is that if in an incoming call packet, the relevant facility bits are
set for fast-select-NRR, then the called DTE can issue a direct response to
the incoming packet using a call-accepted packet that contains
call-user-data. This patch allows such a response.
The called DTE can also respond with a clear-request packet that contains
call-user-data. However, this feature is currently not implemented by the
patch.
How is Fast Select Acceptance used?
By default, the system does not allow fast select acceptance (as before).
To enable a response to fast select acceptance,
After a listen socket in created and bound as follows
socket(AF_X25, SOCK_SEQPACKET, 0);
bind(call_soc, (struct sockaddr *)&locl_addr, sizeof(locl_addr));
but before a listen system call is made, the following ioctl should be used.
ioctl(call_soc,SIOCX25CALLACCPTAPPRV);
Now the listen system call can be made
listen(call_soc, 4);
After this, an incoming-call packet will be accepted, but no call-accepted
packet will be sent back until the following system call is made on the socket
that accepts the call
ioctl(vc_soc,SIOCX25SENDCALLACCPT);
The network (or cisco xot router used for testing here) will allow the
application server's call-user-data in the call-accepted packet,
provided the call-request was made with Fast-select NRR.
Signed-off-by: Shaun Pereira <spereira@tusc.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Shaun Pereira <spereira@tusc.com.au>
This is the first (independent of the second) patch of two that I am
working on with x25 on linux (tested with xot on a cisco router). Details
are as follows.
Current state of module:
A server using the current implementation (2.6.11.7) of the x25 module will
accept a call request/ incoming call packet at the listening x.25 address,
from all callers to that address, as long as NO call user data is present
in the packet header.
If the server needs to choose to accept a particular call request/ incoming
call packet arriving at its listening x25 address, then the kernel has to
allow a match of call user data present in the call request packet with its
own. This is required when multiple servers listen at the same x25 address
and device interface. The kernel currently matches ALL call user data, if
present.
Current Changes:
This patch is a follow up to the patch submitted previously by Andrew
Hendry, and allows the user to selectively control the number of octets of
call user data in the call request packet, that the kernel will match. By
default no call user data is matched, even if call user data is present.
To allow call user data matching, a cudmatchlength > 0 has to be passed
into the kernel after which the passed number of octets will be matched.
Otherwise the kernel behavior is exactly as the original implementation.
This patch also ensures that as is normally the case, no call user data
will be present in the Call accepted / call connected packet sent back to
the caller
Future Changes on next patch:
There are cases however when call user data may be present in the call
accepted packet. According to the X.25 recommendation (ITU-T 10/96)
section 5.2.3.2 call user data may be present in the call accepted packet
provided the fast select facility is used. My next patch will include this
fast select utility and the ability to send up to 128 octets call user data
in the call accepted packet provided the fast select facility is used. I
am currently testing this, again with xot on linux and cisco.
Signed-off-by: Shaun Pereira <spereira@tusc.com.au>
(With a fix from Alexey Dobriyan <adobriyan@gmail.com>)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: jlamanna@gmail.com
ebtables.c vfree() checking cleanups.
Signed-off by: James Lamanna <jlamanna@gmail.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Nishanth Aravamudan <nacc@us.ibm.com>
Use msleep() instead of schedule_timeout() to guarantee the task
delays as expected. The current code is not wrong, but it does not account for
early return due to signals, so I think msleep() should be appropriate.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides support for registering multiple netpoll clients to the
same network device. Only one of these clients may register an rx_hook,
however. In practice, this restriction has not been problematic. It is
worth mentioning, though, that the current design can be easily extended to
allow for the registration of multiple rx_hooks.
The basic idea of the patch is that the rx_np pointer in the netpoll_info
structure points to the struct netpoll that has rx_hook filled in. Aside
from this one case, there is no need for a pointer from the struct
net_device to an individual struct netpoll.
A lock is introduced to protect the setting and clearing of the np_rx
pointer. The pointer will only be cleared upon netpoll client module
removal, and the lock should be uncontested.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a netpoll_info structure, which the struct net_device
will now point to instead of pointing to a struct netpoll. The reason for
this is two-fold: 1) fields such as the rx_flags, poll_owner, and poll_lock
should be maintained per net_device, not per netpoll; and 2) this is a first
step in providing support for multiple netpoll clients to register against the
same net_device.
The struct netpoll is now pointed to by the netpoll_info structure. As
such, the previous behaviour of the code is preserved.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Small patch to save an unecessary call to strlen() : sprintf() gave us
the length, just trust it.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kconfig option had an extra double quote at the end of the line
which was causing in warning when building.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sit tunnel logging is currently broken:
MAC=01:23:45:67:89:ab->01:23:45:47:89:ac TUNNEL=123.123. 0.123-> 12.123. 6.123
Apart from the broken IP address, MAC addresses are printed differently
for sit tunnels than for everything else.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop reference before handing the packets to raw_rcv()
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Keir Fraser <Keir.Fraser@xl.cam.ac.uk>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since expectation timeouts were made compulsory [1], there is no need to
check for them in ip_conntrack_expect_insert.
[1] https://lists.netfilter.org/pipermail/netfilter-devel/2005-January/018143.html
Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netfilter assumes that skb->data == skb->nh.ipv6h
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is a simplified version of the patch to fix a bug in IPv6
multicasting. It:
1) adds existence check & EADDRINUSE error for regular joins
2) adds an exception for EADDRINUSE in the source-specific multicast
join (where a prior join is ok)
3) adds a missing/needed read_lock on sock_mc_list; would've raced
with destroying the socket on interface down without
4) adds a "leave group" in the (INCLUDE, empty) source filter case.
This frees unneeded socket buffer memory, but also prevents
an inappropriate interaction among the 8 socket options that
mess with this. Some would fail as if in the group when you
aren't really.
Item #4 had a locking bug in the last version of this patch; rather than
removing the idev->lock read lock only, I've simplified it to remove
all lock state in the path and treat it as a direct "leave group" call for
the (INCLUDE,empty) case it covers. Tested on an MP machine. :-)
Much thanks to HoerdtMickael <hoerdt@clarinet.u-strasbg.fr> who
reported the original bug.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Essentially netlink at the moment always reports a pid and sequence of 0
always for v6 route activities.
To understand the repurcassions of this look at:
http://lists.quagga.net/pipermail/quagga-dev/2005-June/003507.html
While fixing this, i took the liberty to resolve the outstanding issue
of IPV6 routes inserted via ioctls to have the correct pids as well.
This patch tries to behave as close as possible to the v4 routes i.e
maintains whatever PID the socket issuing the command owns as opposed to
the process. That made the patch a little bulky.
I have tested against both netlink derived utility to add/del routes as
well as ioctl derived one. The Quagga folks have tested against quagga.
This fixes the problem and so far hasnt been detected to introduce any
new issues.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Below is a more generic patch to do fib_lookup via netlink. For others
we should say that we discussed this as a way to verify route selection.
It's also possible there are others uses for this.
In short the fist half of struct fib_result_nl is filled in by caller
and netlink call fills in the other half and returns it.
In case anyone is interested there is a corresponding user app to compare
the full routing table this was used to test implementation of the LC-trie.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the flag XFRM_STATE_NOPMTUDISC for xfrm states. It is
similar to the nopmtudisc on IPIP/GRE tunnels. It only has an effect
on IPv4 tunnel mode states. For these states, it will ensure that the
DF flag is always cleared.
This is primarily useful to work around ICMP blackholes.
In future this flag could also allow a larger MTU to be set within the
tunnel just like IPIP/GRE tunnels. This could be useful for short haul
tunnels where temporary fragmentation outside the tunnel is desired over
smaller fragments inside the tunnel.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: James Morris <jmorris@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the xfrm_state_afinfo->init_flags hook which allows
each address family to perform any common initialisation that does
not require a corresponding destructor call.
It will be used subsequently to set the XFRM_STATE_NOPMTUDISC flag
in IPv4.
It also fixes up the error codes returned by xfrm_init_state.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: James Morris <jmorris@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds xfrm_init_state which is simply a wrapper that calls
xfrm_get_type and subsequently x->type->init_state. It also gets rid
of the unused args argument.
Abstracting it out allows us to add common initialisation code, e.g.,
to set family-specific flags.
The add_time setting in xfrm_user.c was deleted because it's already
set by xfrm_state_alloc.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: James Morris <jmorris@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements sctp_connectx() as defined in the SCTP sockets API draft by
tunneling the request through a setsockopt().
Signed-off-by: Frank Filz <ffilzlnx@us.ibm.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabled, this should disable UCOPY prequeue'ing altogether,
but it does not due to a missing test.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the type of the third parameter 'length' of the
raw_send_hdrinc() function from 'int' to 'size_t'.
This makes sense since this function is only ever called from one
location, and the value passed as the third parameter in that location is
itself of type size_t, so this makes the recieving functions parameter
type match. Also, inside raw_send_hdrinc() the 'length' variable is
used in comparisons with unsigned values and passed as parameter to
functions expecting unsigned values (it's used in a single comparison with
a signed value, but that one can never actually be negative so the patch
also casts that one to size_t to stop gcc worrying, and it is passed in a
single instance to memcpy_fromiovecend() which expects a signed int, but
as far as I can see that's not a problem since the value of 'length'
shouldn't ever exceed the value of a signed int).
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the type of the local variable 'i' in
raw_probe_proto_opt() from 'int' to 'unsigned int'. The only use of 'i' in
this function is as a counter in a for() loop and subsequent index into
the msg->msg_iov[] array.
Since 'i' is compared in a loop to the unsigned variable msg->msg_iovlen
gcc -W generates this warning :
net/ipv4/raw.c:340: warning: comparison between signed and unsigned
Changing 'i' to unsigned silences this warning and is safe since the array
index can never be negative anyway, so unsigned int is the logical type to
use for 'i' and also enables a larger msg_iov[] array (but I don't know if
that will ever matter).
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch gets rid of the following gcc -W warning in net/ipv4/raw.c :
net/ipv4/raw.c:387: warning: comparison of unsigned expression < 0 is always false
Since 'len' is of type size_t it is unsigned and can thus never be <0, and
since this is obvious from the function declaration just a few lines above
I think it's ok to remove the pointless check for len<0.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch silences these two gcc -W warnings in net/ipv4/raw.c :
net/ipv4/raw.c:517: warning: signed and unsigned type in conditional expression
net/ipv4/raw.c:613: warning: signed and unsigned type in conditional expression
It doesn't change the behaviour of the code, simply writes the conditional
expression with plain 'if()' syntax instead of '? :' , but since this
breaks it into sepperate statements gcc no longer complains about having
both a signed and unsigned value in the same conditional expression.
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes the skb trimming code which is not needed since we never
touch the skb upon failure. Removes unnecessary initializers,
and simplifies the code a bit.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
prio2list() returns the relevant sk_buff_head for the
band specified by the priority for a given skb.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes the skb trimming code which is not needed since we never
touch the skb upon failure. Removes unnecessary includes,
initializers, and simplifies the code a bit.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The simplicity of the fifo qdisc allows several qdisc operations to be
redirected to the relevant queue management function directly. Saves
a lot of code lines and gives the pfifo a byte based backlog.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the spin_lock_irqsave call on the receive queue
lock in SCTP with spin_lock_bh. Despite the proliferation of
spin_lock_irqsave calls in this stack, it is only entered from the
IPv4/IPv6 stack and user space. That is, it is never entered from
hardirq context.
The call in question is only called from recvmsg which means that
IRQs aren't disabled. Therefore it is safe to replace it with
spin_lock_bh.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In light of my recent patch to net/ipv4/udp.c that replaced the
spin_lock_irq calls on the receive queue lock with spin_lock_bh,
here is a similar patch for all other occurences of spin_lock_irq
on receive/error queue locks in IPv4 and IPv6.
In these stacks, we know that they can only be entered from user
or softirq context. Therefore it's safe to disable BH only.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ensures that netlink events created as a result of programns
using ioctls (such as ifconfig, route etc) contains the correct PID of
those events.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts "unsigned flags" to use more explict types like u16
instead and incrementally introduces NLMSG_NEW().
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch was supposed to be part of the neighbour tables related
patchset but apparently got lost.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the format of the XFRM_MSG_DELSA and
XFRM_MSG_DELPOLICY notification so that the main message
sent is of the same format as that received by the kernel
if the original message was via netlink. This also means
that we won't lose the byid information carried in km_event.
Since this user interface is introduced by Jamal's patch
we can still afford to change it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch rectifies some rtnetlink message builders that derive the
flags from the pid. It is now explicit like the other cases
which get it right. Also fixes half a dozen dumpers which did not
set NLM_F_MULTI at all.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduces a new macro NLMSG_NEW which extends NLMSG_PUT but takes
a flags argument. NLMSG_PUT stays there for compatibility but now
calls NLMSG_NEW with flags == 0. NLMSG_PUT_ANSWER is renamed to
NLMSG_NEW_ANSWER which now also takes a flags argument.
Also converts the users of NLMSG_PUT_ANSWER to use NLMSG_NEW_ANSWER
and fixes the two direct users of __nlmsg_put to either provide
the flags or use NLMSG_NEW(_ANSWER).
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
