As long as there is no other non-const variable marked __initdata in the
same compilation unit it doesn't hurt. If there were one however
compilation would fail with
error: $variablename causes a section type conflict
because a section containing const variables is marked read only and so
cannot contain non-const variables.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: kernel@pengutronix.de
Patchwork: https://patchwork.linux-mips.org/patch/3565/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MSI interrupts do not work on XLS after commit a776c49
( "PCI: msi: Disable msi interrupts when we initialize a pci device" )
because the change disables MSI interrupts on the XLS PCIe bridges
during the PCI enumeration.
Fix this by enabling MSI interrupts on the bridge in the
arch_setup_msi_irq() function. A new function xls_get_pcie_link()
has been introduced to get the PCI device corresponding to the
top level PCIe bridge on which MSI has to be enabled.
Also, update get_irq_vector() to use the new xls_get_pcie_link()
function and PCI_SLOT() macro for determining the IRQ of PCI devices.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3753/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Implement support for OF inside the lantiq PCI driver. The patch also splits
pcibios_plat_dev_init and pcibios_map_irq out into their own file to accomodate
coexistance with the upcoming pcie driver.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3806/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As part of the conversion to OF we also implement pinctrl drivers. Previously
we used ltq_gpio_request() to set pinmuxing. This is now obselete and we can
hence drop the function.
Additionally we remove gpio_to_irq() from the gpio driver and move it to a
header file.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3801/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Implement pci_load_of_ranges on MIPS. Due to lack of test hardware only 32bit
bus width is supported. This function is based on pci_process_bridge_OF_ranges
from powerpc.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3729/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The AR724X specific PCI code can be used for the
AR934X SoCs, however it can be selected only if
SOC_AR724X is set.
Introduce a new Kconfig symbol in order to be able
to use the code for AR934X as well.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Cc: linux-mips@linux-mips.org
Cc: mcgrof@infradead.org
Patchwork: https://patchwork.linux-mips.org/patch/3514/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add copyright records according to the recent changes in
the PCI code. Also fix up the descriptions.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3503/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Atheros AR71XX SoCs have a built-in PCI Host Controller.
This patch adds a driver for that, and modifies the relevant
files in order to allow to register the PCI controller from
board specific setup.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3498/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PCI Host Controller of the AR724x SoC has a
built-in IRQ controller. The current code does
not supports that, so the IRQ lines wired to this
controller are not usable. This leads to failed
'request_irq' calls:
ath9k 0000:00:00.0: request_irq failed
ath9k: probe of 0000:00:00.0 failed with error -89
This patch adds support for the IRQ controller
in order to make PCI IRQs work.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3496/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current ar724x_pci_{read,write} functions are
broken. Due to that, pci_read_config_byte returns
with bogus values, and pci_write_config_{byte,word}
unconditionally clears the accessed PCI configuration
registers instead of changing the value of them.
The patch fixes the broken functions, thus the PCI
configuration space can be accessed correctly.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3493/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace the 'ath724x' to 'ar724x' in function, variable and
structure names to reflect the name of the real SoC.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: René Bolldorf <xsecute@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3490/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current code unconditionally registers the AR724X
specific PCI controller, even if the kernel is running
on a different SoC.
Add a common function for PCI controller registration,
and only register the AR724X PCI controller if the kernel
is running on an AR724X SoC.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3488/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The 'pcibios_map_irq' and 'pcibios_plat_dev_init'
are common functions and only instance one of them
can be present in a single kernel.
Currently these functions can be built only if the
CONFIG_SOC_AR724X option is selected. However the
ath79 platform contain support for the AR71XX SoCs,.
The AR71XX SoCs have a differnet PCI controller,
and those will require a different code.
Move the common PCI code into a separeate file in
order to be able to use that with other SoCs as
well.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: René Bolldorf <xsecute@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3485/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fixes
warning: data definition has no type or storage class [enabled by default]
warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Wimplicit-int]
warning: parameter names (without types) in function declaration [enabled by default]
Signed-off-by: Matt Turner <mattst88@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3746/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull PCI changes (including maintainer change) from Jesse Barnes:
"This pull has some good cleanups from Bjorn and Yinghai, as well as
some more code from Yinghai to better handle resource re-allocation
when enabled.
There's also a new initcall_debug feature from Arjan which will print
out quirk timing information to help identify slow quirks for fixing
or refinement (Yinghai sent in a few patches to do just that once the
new debug code landed).
Beyond that, I'm handing off PCI maintainership to Bjorn Helgaas.
He's been a core PCI and Linux contributor for some time now, and has
kindly volunteered to take over. I just don't feel I have the time
for PCI review and work that it deserves lately (I've taken on some
other projects), and haven't been as responsive lately as I'd like, so
I approached Bjorn asking if he'd like to manage things. He's going
to give it a try, and I'm confident he'll do at least as well as I
have in keeping the tree managed, patches flowing, and keeping things
stable."
Fix up some fairly trivial conflicts due to other cleanups (mips device
resource fixup cleanups clashing with list handling cleanup, ppc iseries
removal clashing with pci_probe_only cleanup etc)
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (112 commits)
PCI: Bjorn gets PCI hotplug too
PCI: hand PCI maintenance over to Bjorn Helgaas
unicore32/PCI: move <asm-generic/pci-bridge.h> include to asm/pci.h
sparc/PCI: convert devtree and arch-probed bus addresses to resource
powerpc/PCI: allow reallocation on PA Semi
powerpc/PCI: convert devtree bus addresses to resource
powerpc/PCI: compute I/O space bus-to-resource offset consistently
arm/PCI: don't export pci_flags
PCI: fix bridge I/O window bus-to-resource conversion
x86/PCI: add spinlock held check to 'pcibios_fwaddrmap_lookup()'
PCI / PCIe: Introduce command line option to disable ARI
PCI: make acpihp use __pci_remove_bus_device instead
PCI: export __pci_remove_bus_device
PCI: Rename pci_remove_behind_bridge to pci_stop_and_remove_behind_bridge
PCI: Rename pci_remove_bus_device to pci_stop_and_remove_bus_device
PCI: print out PCI device info along with duration
PCI: Move "pci reassigndev resource alignment" out of quirks.c
PCI: Use class for quirk for usb host controller fixup
PCI: Use class for quirk for ti816x class fixup
PCI: Use class for quirk for intel e100 interrupt fixup
...
Conflicts:
drivers/net/vmxnet3/vmxnet3_drv.c
Small vmxnet3 conflict with header size bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.
Here's the wrinkle on Cobalt: we can't generate normal I/O port addresses
on PCI because the GT-64111 doesn't do any address translation, so we have
this:
CPU I/O port addresses [io 0x0000-0xffffff]
PCI bus I/O port addresses [io 0x10000000-0x10ffffff]
Legacy-mode IDE controllers start out with the legacy bus addresses, e.g.,
0x1f0, assigned by pci_setup_device(). These are outside the range of
addresses GT-64111 can generate on PCI, but pcibios_fixup_device_resources()
converted them to CPU addresses anyway by adding io_offset. Therefore, we
had to pre-adjust them in cobalt_legacy_ide_fixup().
With io_offset = 0xf0000000, we had this:
res->start = 0x1f0 initialized in pci_setup_device()
res->start = 0x100001f0 -= io_offset in cobalt_legacy_ide_fixup()
res->start = 0x1f0 += io_offset in pcibios_fixup_device_resources()
The difference after this patch is that the generic pci_bus_to_resource()
only adds the offset if the bus address is inside a host bridge window.
Since 0x1f0 is not a valid bus address and is not inside any windows, it is
unaffected, so we now have this:
region->start = 0x1f0 initialized in pci_setup_device()
res->start = 0x1f0 no offset by pci_bus_to_resource()
That means we can remove both pcibios_fixup_device_resources() and
cobalt_legacy_ide_fixup().
I would *rather* set the host bridge offset to zero (which corresponds
to what the GT-64111 actually does), and have both CPU and PCI addresses
of [io 0x10000000-0x10ffffff]. However, that would require changes to
generic code that assumes legacy I/O addresses, such as pic1_io_resource
([io 0x0020-0x00021]), and we'd have to keep a Cobalt IDE fixup.
Of course, none of this changes the fact that references to I/O port
0x1f0 actually go to port 0x100001f0, not 0x1f0, on the Cobalt PCI bus.
Fortunately the VT82C586 IDE controller only decodes the low 24 address
bits, so it does work.
CC: Ralf Baechle <ralf@linux-mips.org>
CC: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We never assign anything other than PCI_ASSIGN_ALL_BUSSES to pci_probe,
so just remove the indirection. If configurability is required in the
future, please use the pci_flags/PCI_REASSIGN_ALL_BUS functionality
as is done for powerpc.
CC: Ralf Baechle <ralf@linux-mips.org>
CC: linux-mips@linux-mips.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some architectures (alpha, mips, powerpc) have an arch-specific
"pci_probe_only" flag. Others use PCI_PROBE_ONLY in pci_flags for
the same purpose. This moves mips to the pci_flags approach so
generic code can use the same test across all architectures.
CC: Ralf Baechle <ralf@linux-mips.org>
CC: linux-mips@linux-mips.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some SoCs have a PCIe host controller to make it possible to attach
some other devices to it, like an other Wifi card.
This code was tested with an Netgear WNDR3400 (bcm4716 based), but
should work with all bcma based SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On MIPS the generic PCI code has always defaulted to L1_CACHE_BYTES
because the architecutre PCI code did not provide a better default.
In particular on systems with S-caches or T-caches this was suboptimal.
Provide a better default by setting pci_dfl_cache_line_size based on
the size of the line size of the lowest level of the cache hierarchy.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2982/
Convert from pci_scan_bus() to pci_scan_root_bus() and remove root bus
resource fixups. This fixes the problem of "early" and "header" quirks
seeing incorrect root bus resources.
Based on original patch by Deng-Cheng Zhu.
Reference: https://lkml.org/lkml/2011/8/26/89
CC: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Deng-Cheng Zhu <dczhu@mips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The 'latency timer' of PCI devices, both Type 0 and Type 1,
is setup in architecture-specific code [see: 'pcibios_set_master()'].
There are two approaches being taken by all the architectures - check
if the 'latency timer' is currently set between 16 and 255 and if not
bring it within bounds, or, do nothing (and then there is the
gratuitously different PA-RISC implementation).
There is nothing architecture-specific about PCI's 'latency timer' so
this patch pulls its setup functionality up into the PCI core by
creating a generic 'pcibios_set_master()' function using the '__weak'
attribute which can be used by all architectures as a default which,
if necessary, can then be over-ridden by architecture-specific code.
No functional change.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
- Move code that can be shared with XLP (irq.c, smp.c, time.c and
xlr_console.c) to arch/mips/netlogic/common
- Add asm/netlogic/haldefs.h and asm/netlogic/common.h for common and
io functions shared with XLP
- remove type 'nlm_reg_t *' and use uint64_t for mmio offsets
- Move XLR specific code in smp.c to xlr/wakeup.c
- Move XLR specific PCI code from irq.c to mips/pci/pci-xlr.c
- Provide API for pic functions called from common/irq.c
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2964/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The CPU_XLR config variable is sufficient for XLR compilation, the
variable NLM_XLR can be removed.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2962/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled and we even check
and yell when an interrupt handler returns with interrupts enabled (see
commit [b738a50a: genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
[ralf@linux-mips.org: Fixed up conflicts in
arch/mips/alchemy/common/dbdma.c, arch/mips/cavium-octeon/smp.c and
arch/mips/kernel/perf_event.c.]
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
To: linux-kernel@vger.kernel.org
Cc: tglx@linutronix.delinux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2835/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move add_wired_entry to its own header file from where it will be
always included. Patch up other users of add_wired_entry to also include
the header as needed.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Panic() invokes printk() to add a \n internally, so panic arguments should
not themselves end in \n. Panic invocations in arch/mips and elsewhere
are inconsistently sometimes terminating in \n, sometimes not.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move PCI Controller PM to syscore_ops since the platform_driver PM methods
are called way too late on resume and far too early on suspend (after and
before PCI device resume/suspend).
This also allows to simplify wired entry management a bit.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3007/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The code located at arch/mips/lantiq/ included module.h to be able to use
the EXPORT_SYMBOL* macros. These can now be directly included using
export.h.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2937/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
