Add support for the NVRAM lock-out feature for TPM in 5752. If lock-out
is enabled, certain NVRAM registers cannot be written to.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add bit definitions for the new GPIO3 in 5752. GPIO3 must be driven as
output when it is unused.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5752 A0 chip ID is wrong in hardware. The simplest way to workaround
it is to change it to the correct value in tp->pci_chip_rev_id. This
way, it is easier to check for the ASIC_REV_5752 in the rest of the
driver.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix tg3_set_power_state to drive GPIOs properly based on the
TG3_FLAG_EEPROM_WRITE_PROTECT flag. Some delays are also added after D0
and D3 power state changes.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setup proper GPIO settings in tp->grc_local_ctrl before calling
tg3_set_power() state in tg3_get_invariants() and after chip reset.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the 1st half of tg3_phy_probe() into tg3_get_eeprom_hw_cfg() so
that the TG3_FLAG_EEPROM_WRITE_PROT can be determined before calling
tg3_set_power_state() in tg3_get_invariants(). This will allow
tg3_set_power_state() to drive the GPIOs correctly based on the config.
information in eeprom.
On the 5752, there are no pull-up resistors on the GPIO pins and it is
necessary to drive the unused GPIOs as output.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some minor 5752 fixes mostly for correctness and add 5752 PHY ID.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace existing ASIC_REV_5752 definition with ASIC_REV_5752_A0,
and add definition for ASIC_REV_5752_A1. Then, add ASIC_REV_5752_A1
to check for setting TG3_FLG2_5750_PLUS in tg3_get_invariants.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use check of TG3_FLG2_5750_PLUS in tg3_get_invariants to set
TG3_FLG2_5705_PLUS flag.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rewrite checks in tg3_get_invariants to use TG3_FLG2_5705_PLUS and
TG3_FLG2_5750_PLUS flags.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rewrite of a couple of troublesome multi-way if statements to use
TG3_FLG2_5705_PLUS flag.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace a number of two-way if statements checking for 5750, and/or
5752 to reference the newly-defined TG3_FLG2_5750_PLUS flag instead.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define TG3_FLG2_5750_PLUS flag and set it in tg3_get_invariants for
ASIC_REV_5750 or ASIC_REV_5752.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace a number of three-way if statements checking for 5705, 5750,
and 5752 to reference the equivalent TG3_FLG2_5705_PLUS flag instead.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add proper entry for bcm5752 PCI ID to pci_ids.h, and use it in tg3.
I did this separately in case patches like this (i.e. new PCI IDs)
need to come from more "official" sources.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hard-coded definition of bcm5752 PCI ID to tg3_pci_tbl.
Next patch will change entry to use pci_ids.h-based definition.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ASIC_REV_5752 definition.
Track-down all references to ASIC_REV_5750 and mirror them with
references to the newly defined ASIC_REV_5752.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I.e. not using skb->dev as a way to pass the parameter used to fill...
skb->dev :-)
Also to get the _type_trans open coded sequence grouped, next changesets
will introduce ax25_type_trans.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
While we're at it, lets also replace KERN_INFO by KERN_EMERG to
make sure the user gets to see it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch to arch/i386/kernel/cpu/amd.c relies on the variable
cpu_core_id which is defined in i386/kernel/smpboot.c. This means it is
only present if CONFIG_X86_SMP is defined, not CONFIG_SMP (alternative
SMP harnesses won't have it, which is why it breaks voyager).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix non-legacy multichannel ISO receive, broken by Parag Wardukar's
allocation fix. Multichannel ISO receive still sucks; it should be possible
to use both legacy and non-legacy modes at the same time, but with this
patch, things are no worse than they were in 2.6.11 and allocation is
still done at the correct time.
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Print the correct value in the DBGMSG in dma_rcv_tasklet().
See OHCI 1.1 section 8.7, page 103 ff.
- Print tlabels as %d everywhere.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The ia64-version of fls() never worked as intended (the bitnumbering
was off by 1 and fls(0) was undefined). This patch fixes the problem
by using a popcnt-based fls(), which on McKinley-derived cores is
slightly faster than both ia64_fls() and generic_fls(). The resulting
code, however, is bigger (7-8 bundles instead of about 3 bundles).
Also switch ia64_popcnt() to __builtin_popcountl() for GCC v3.4 or
newer since the compiler can predicate that and schedule it better.
Thanks to Simon Derr and Matt Mackall for tracking down this bug.
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
We do not longer use DLT_LINUX_SLL for activ/pass filters but
DLT_PPP_WITHDIRECTION witch need 1 as outbound flag.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The new out of line put_user() assembly on x86_64 changes %rcx without
telling GCC about it causing things like:
http://bugme.osdl.org/show_bug.cgi?id=4515
See to it that %rcx is not changed (made it consistent with get_user()).
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: ak@suse.de
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
My version of gcc doesn't warn about this error (declaration in the
middle of a set of statements).
The fix is simple (this also corrects return code; for init functions it
should be zero or error).
PREEMPT+SMP support - see if it looks sane...
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch just makes the header part of the skb writeable.
This is needed since we modify the IP headers just a few lines below.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is a revised alternative that uses BUG_ON/WARN_ON
(as suggested by Herbert Xu) to eliminate NET_CALLER.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be kind to userspace and don't force them to hardcode protocol
families just to have it changed again once we support routing
rules for more than one protocol family.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
While looking at this problem I noticed that IPv6 was sometimes
looking at inet->recverr which is bogus. Here is a patch to
correct that and use np->recverr.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
So here is a patch that introduces skb_store_bits -- the opposite of
skb_copy_bits, and uses them to read/write the csum field in rawv6.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once all the MMU architectures define FIRST_USER_ADDRESS, remove hack from
mmap.c which derived it from FIRST_USER_PGD_NR.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace misleading definition of FIRST_USER_PGD_NR 0 by definition of
FIRST_USER_ADDRESS 0 in all the MMU architectures beyond arm and arm26.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ARM26 define FIRST_USER_ADDRESS as PAGE_SIZE (beyond the machine vectors when
they are mapped low), and use that definition in place of locally defined
MIN_MAP_ADDR. Previously, ARM26 permitted user mappings at 0 if the machine
vectors were mapped high; but that's inconsistent with ARM, and
FIRST_USER_ADDRESS would then have to be determined at runtime. Let's fix it
at PAGE_SIZE throughout the architecture.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ARM define FIRST_USER_ADDRESS as PAGE_SIZE (beyond the machine vectors when
they are mapped low), and use that definition in place of locally defined
MIN_MAP_ADDR.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove use of FIRST_USER_PGD_NR from sys_mincore: it's inconsistent (no other
syscall refers to it), unnecessary (sys_mincore loops over vmas further down)
and incorrect (misses user addresses in ARM's first pgd).
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
