After the transition from cs4321_lib to wss_lib, azt2320 probe visits
snd_ad1848_probe during detection. It expects register 0 (LEFT_INPUT)
to be able to retain the value 0xaa during detection but AZT2320 does
not support MIC gain meaning it reads back as 0x8a instead.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Remove initializations of spinlock and mutexes which
are done earlier in snd_wss_new(). The snd_wss_new()
is called from snd_wss_create().
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
snd-opti92x-ad1848 mistakingly passes WSS_HW_OPTI93X currently. This
fixes it as tested with a OPTi 82C929A/AD1848 card.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Limit opti93x cards capture formats to only linear ones.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reviewed-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Use the wss detection code and kill the ad1848 library.
The library is fully assimilated into the new wss library.
This required reworking of the AD1848 family code
so the code is changed to correctly detect chips from
the AD1848 and CS4231 families.
I have tested it on following cards:
Gallant SC-6600 (codec: AD1848, driver: snd-sc6600)
SoundScape VIVO/90 (codec: AD1845, driver: snd-sscape)
SG Waverider (codec: CS4231A, driver: Rene Herman's snd-galaxy)
Opti930 (codec: built-in - CS4231 compatible, driver: snd-opti93x)
Opti931 (codec: built-in - CS4231 compatible, driver: snd-opti93x)
Gallant SC-70P (chip/codec: CS4237B, driver: snd-cs4236)
Audio Plus 3D (chip/codec: CMI8330A, driver: snd-cmi8330)
Dell Latitude CP (chip/codec: cs4236, driver snd-cs4232)
Sound playback and recording works on all these cards.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reviewed-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Use the wss pcm code and kill the ad1848 pcm code.
The AD1848 chip is much slower than CS4231 chips
so the waiting loop was increased 100x (10x is not
enough).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reviewed-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Use the wss mixer code and kill the ad1848 mixer code.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reviewed-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Use CS4231P instead of AD1848P (kill the AD1848P).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reviewed-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Use the wss macros instead of ad1848 ones.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reviewed-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Use wss constants for mode.
Move ad1848 hardware constants to the wss.h.
Move mixer tlv macros into the ad1848_lib.c from the ad1848.h.
Drop the MODE_RUNNING spurious IRQ guard on AD1848 as it doesn not seem
to be needed.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reviewed-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The snd_wss is superset of the snd_ad1848 so kill
the latter and replace it with the snd_wss.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reviewed-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Rename functions and structures from the former
cs4321_lib to names more corresponding with the
new name: wss_lib.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reviewed-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Rename file include/sound/cs4231.h
into include/sound/wss.h
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reviewed-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Move the file sound/isa/cs423x/cs4231_lib.c
into sound/isa/cs423x/wss_lib.c
This is the first step toward merging all libraries
for Windows Sound System compatible chips
into a single library.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reviewed-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
snd_seq_oss_synth_make_info() incorrectly reports information
to userspace without first checking for the validity of the
device number, leading to possible information leak (CVE-2008-3272).
Reported-By: Tobias Klein <tk@trapkit.de>
Acked-and-tested-by: Takashi Iwai <tiwai@suse.de>
Cc: stable@kernel.org
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If an OSS application calls SNDCTL_DSP_SYNC, then ALSA will call the driver's
_hw_params and _prepare functions again. On the Freescale MPC8610 DMA ASoC
driver, this caused the DMA controller to be unneccessarily re-programmed, and
apparently it doesn't like that. The DMA will then not operate when
instructed. This patch relocates much of the DMA programming to
fsl_dma_open(), which is called only once.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: ASoC: Export dapm_reg_event() fully
ALSA: ASoC: Update Poodle to current ASoC API
ALSA: asoc: restrict sample rate and size in Freescale MPC8610 sound drivers
ALSA: sound/soc/pxa/tosa.c: removed duplicated include
When compiled with CONFIG_SND_DYNAMIC_MINORS the ALSA core is fine
to have more than 8 PCM devices per card, except one place - the
SNDRV_CTL_IOCTL_PCM_NEXT_DEVICE ioctl, which will not enumerate
devices > 7. This patch fixes the issue, changing the devices list
organisation.
Instead of adding new device to the tail, the list is now kept always
ordered (by card number, then device number). Thus, during enumeration,
it is easy to discover the fact that there is no more given card's
devices.
Additionally the device field of struct snd_pcm had to be changed to int,
as its "unsignednity" caused a lot of problems when comparing it to
potentially negative signed values. (-1 is 0xffffffff or even more then ;-)
Signed-off-by: Pawel Moll <pawel.moll@st.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added a new US122L usb-audio driver. This driver works together with a
dedicated alsa-lib plugin.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This reverts commit fb3d6f2b77bdec75d45aa9d4464287ed87927866.
New, updated patch with same subject replaces this commit.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
When compiled with CONFIG_SND_DYNAMIC_MINORS the ALSA core is fine
to have more than 8 PCM devices per card, except one place - the
SNDRV_CTL_IOCTL_PCM_NEXT_DEVICE ioctl, which will not enumerate
devices > 7. This patch fixes the issue, changing the devices list
organisation.
Instead of adding new device to the tail, the list is now kept always
ordered (by card number, then device number). Thus, during enumeration,
it is easy to discover the fact that there is no more given card's
devices. The same limit was present in OSS emulation code. It has
been fixed as well.
Additionally the device field of struct snd_pcm is now int, instead of
unsigned int, as there is no obvious reason for keeping it unsigned.
This caused a lot of problems with comparing this value with other
(almost always signed) variables. There is just one more place where
device number is unsigned - in struct snd_pcm_info, which should be
also sorted out in future.
Signed-off-by: Pawel MOLL <pawel.moll@st.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
ASOC: convert use of uint to unsigned int
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Allow all the CODEC drivers to be built without a machine driver in order
to facilitate testing of subsystem-wide changes and gain better coverage
from automated testing efforts. This also helps things like the generic
OpenFirmware machine driver for PowerPC.
Currently AC97 CODECs are not included since the current setup relies
on having a controller driver available.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This fixes sparse warnings and allows non-OpenFirmware systems to attempt
to bind to the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
ASoC Codec driver for the TLV320AIC26 device. As it stands, this driver
doesn't support all the modes and clocking options of the AIC16, but it
is a start.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This is an I2S bus driver for the MPC5200 PSC device. It depends on the
soc-of helper functions to match a PSC device with a codec based on data
in the device tree.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Simple utility layer for creating ASoC machine instances based on data
in the OpenFirmware device tree. OF aware platform drivers and codec
drivers register themselves with this framework and the framework
automatically instantiates a machine driver. At the moment, the driver
is not very capable and it is expected to be extended as more features
are needed for specifying the configuration in the device tree.
This is most likely temporary glue code to work around limitations in
the ASoC v1 framework. When v2 is merged, most of this driver will
need to be reworked.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Most of the ASoC controls refer to the maximum value that can be set for
a control as mask but there is no actual requirement for all bits to be
set at the highest possible value making the name mask misleading.
Change the code to use max instead.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Convert bitfields in ASoC into full int width. This is a
simple mechanical conversion. Two places in the DAPM code
were fixed to properly use mask.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Some codecs have unusual features in their register maps such as very
large registers representing arrays of coefficients. Support these
codecs in the register cache sysfs file by allowing them to provide a
function register_display() overriding the default output for register
contents.
Also ensure that we don't overflow PAGE_SIZE while writing out the
register dump.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Use input_free_devce() correctly instead of kfree() at error path.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Since jack detection requires the input subsystem which may not be
desired on small systems it is not built unless required by a driver
that is being built. Drivers using jack detection should use a pattern
like this:
config SND_FOO
tristate "..."
...
select SND_JACK if INPUT=y || INPUT=SND
to ensure that the jack detection API is enabled if the input subsystem
is. If the input subsystem is not enabled then a stub version of the
API is provided.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Currently very few systems provide information about jack status to user
space, even though many have hardware facilities to do detection. Those
systems that do use an input device with the existing SW_HEADPHONE_INSERT
switch type to do so, often independently of ALSA.
This patch introduces a standard method for representing jacks to user
space into ALSA. It allows drivers to register jacks for a sound card with
the input subsystem, binding the input device to the card to help user
space associate the input devices with their sound cards. The created
input devices are named in the form "card longname jack" where jack is
provided by the driver when allocating a jack. By default the parent for
the input device is the sound card but this can be overridden by the
card driver.
The existing user space API with SW_HEADPHONE_INSERT is preserved.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
dapm_reg_event() is used by devices using SND_SOC_DAPM_REG() so needs to
be exported to support building them as modules and prototyped to avoid
sparse warnings and potential build issues.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Freescale MPC8610 SSI device has the option of using one clock for both
transmit and receive (synchronous mode), or independent clocks (asynchronous).
The SSI driver, however, programs the SSI into synchronous mode and then
tries to program the clock registers independently. The result is that the wrong
sample size is usually generated during recording.
This patch fixes the discrepancy by restricting the sample rate and sample size
of the playback and capture streams. The SSI driver remembers which stream
is opened first. When a second stream is opened, that stream is constrained
to the same sample rate and size as the first stream.
A future version of this driver will lift the sample size restriction.
Supporting independent sample rates is more difficult, because only certain
codecs provide dual independent clocks.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Removed duplicated include <asm/arch/tosa.h> in
sound/soc/pxa/tosa.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This follows the sparc changes a439fe51a1.
Most of the moving about was done with Sam's directions at:
http://marc.info/?l=linux-sh&m=121724823706062&w=2
with subsequent hacking and fixups entirely my fault.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Added support for 92HD81/83 family of codecs.
This also includes a pwr_mapping array for pins that have more than
one amp to power down.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: Allow to force model to intel-mac-v3 in snd_hda_intel (sigmatel).
ALSA: cs4232: fix crash during chip PNP detection
ALSA: hda - Add automatic model setting for the Acer Aspire 5920G laptop
ALSA: make snd_ac97_add_vmaster() static
ALSA: sound/pci/azt3328.h: no variables for enums
ALSA: soc - wm9712 mono mixer
ALSA: hda - Add support of ASUS Eeepc P90*
ALSA: opti9xx: no isapnp param for !CONFIG_PNP
ALSA: opti93x - Fix NULL dereference
ALSA: hda - Added support for Asus V1Sn
ALSA: ASoC: Factor PGA DAPM handling into main
ALSA: ASoC: Refactor DAPM event handler
ALSA: ALSA: ens1370: communicate PCI device to AC97
ALSA: ens1370: SRC stands for Sample Rate Converter
ALSA: hda - Align BDL position adjustment parameter
ALSA: Au1xpsc: psc not disabled when TX is idle
ALSA: add TriTech 28023 AC97 codec ID and Wolfson 9701 name.
The type and type2 fields were unused and so could be removed.
Instead add a vfl_type field that contains the type of the video
device.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently, even if you pass model=intel-mac-v3 as a module parameter to
snd_hda_intel, the function patch_stac922x (patch_sigmatel.c) will still
try to auto-detect the model type. This is a problem on my MacBook Pro 1st
generation, which needs intel-mac-v3, but sometimes incorrectly reports
0x00000100 as subsystem id, which causes the switch in patch_stac922x to
select intel-mac-v4.
To fix this, I added a new model called intel-mac-auto, so in case no
module parameter is passed, and an Intel Mac board is detected, the
model will be automatically detected, while no detection will be done
if the model is forced to intel-mac-v3.
This problem has been around for quite a while, and I used to fix it
by moving the case statement for 0x00000100 in patch_stac922x so that
intel-mac-v3 is chosen.
Another way to fix the problem would be to check if a module parameter
was set directly in patch_stac922x, using something like this:
if (spec->board_config == STAC_INTEL_MAC_V3 &&
!codec->bus->modelname) {
But I think it is less elegant (if you prefer that way, I can prepare a
patch).
Signed-off-by: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The acard->wss pointer is uninitialized in this function
which leads to crash during chip PNP detection.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make the Acer Aspire 5920G (1025:0121) select ALC883_ACER_ASPIRE
by default.
Signed-off-by: Travis Place <wishie@wishie.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch makes the needlessly global snd_ac97_add_vmaster() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AZF_FREQUENCIES and AZF_GAME_CONFIGS were variables, and this doesn't
seem to have been intended.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver is gone for a long time.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SOUND_TRIDENT was the last PCI OSS driver, and since there's already an
ALSA driver for the same hardware we can remove it.
[muli@il.ibm.com: update CREDITS]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On 32-bit architectures PAGE_ALIGN() truncates 64-bit values to the 32-bit
boundary. For example:
u64 val = PAGE_ALIGN(size);
always returns a value < 4GB even if size is greater than 4GB.
The problem resides in PAGE_MASK definition (from include/asm-x86/page.h for
example):
#define PAGE_SHIFT 12
#define PAGE_SIZE (_AC(1,UL) << PAGE_SHIFT)
#define PAGE_MASK (~(PAGE_SIZE-1))
...
#define PAGE_ALIGN(addr) (((addr)+PAGE_SIZE-1)&PAGE_MASK)
The "~" is performed on a 32-bit value, so everything in "and" with
PAGE_MASK greater than 4GB will be truncated to the 32-bit boundary.
Using the ALIGN() macro seems to be the right way, because it uses
typeof(addr) for the mask.
Also move the PAGE_ALIGN() definitions out of include/asm-*/page.h in
include/linux/mm.h.
See also lkml discussion: http://lkml.org/lkml/2008/6/11/237
[akpm@linux-foundation.org: fix drivers/media/video/uvc/uvc_queue.c]
[akpm@linux-foundation.org: fix v850]
[akpm@linux-foundation.org: fix powerpc]
[akpm@linux-foundation.org: fix arm]
[akpm@linux-foundation.org: fix mips]
[akpm@linux-foundation.org: fix drivers/media/video/pvrusb2/pvrusb2-dvb.c]
[akpm@linux-foundation.org: fix drivers/mtd/maps/uclinux.c]
[akpm@linux-foundation.org: fix powerpc]
Signed-off-by: Andrea Righi <righi.andrea@gmail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (85 commits)
[ARM] pxa: add base support for PXA930 Handheld Platform (aka SAAR)
[ARM] pxa: add base support for PXA930 Evaluation Board (aka TavorEVB)
[ARM] pxa: add base support for PXA930 (aka Tavor-P)
[ARM] Update mach-types
[ARM] pxa: make littleton to use the new smc91x platform data
[ARM] pxa: make zylonite to use the new smc91x platform data
[ARM] pxa: make mainstone to use the new smc91x platform data
[ARM] pxa: make lubbock to use new smc91x platform data
[NET] smc91x: prepare SMC_USE_PXA_DMA to be specified in platform data
[NET] smc91x: prepare for SMC_IO_SHIFT to be a platform configurable variable
[NET] smc91x: add SMC91X_NOWAIT flag to platform data
[NET] smc91x: favor the use of SMC91X_USE_* instead of SMC_CAN_USE_*
[NET] smc91x: remove "irq_flags" from "struct smc91x_platdata"
[ARM] 5146/1: pxa2xx: convert all boards to call pxa2xx_transceiver_mode helper
Support for LCD on e740 e750 e400 and e800 e-series PDAs
E-series UDC support
PXA UDC - allow use of inverted GPIO for pullup
Add e350 support
Fix broken e-series build
E-series GPIO / IRQ definitions.
...
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added digital pc-beep support using linear tone generation for hd-codecs along
with initial support for several IDT codecs.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Correct headphone detection for 1st generation iMac G3 Slot-loading (Screamer).
This patch fixes the regression in the recent snd-powermac which
doesn't support some G3/G4 PowerMacs:
http://lkml.org/lkml/2008/10/1/220
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Tested-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add mixer controls for PowerMac G4 AGP (Screamer).
This patch fixes the regression in the recent snd-powermac which
doesn't support some G3/G4 PowerMacs:
http://lkml.org/lkml/2008/10/1/220
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Tested-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rob Sims wrote:
"I can't seem to turn on register 0x17, bit 3 in the sound chip, except
by codec_reg_write; the mixer lacks direct or indirect control. It
seems there are two names for the output of the rec mixer:
Capture ST Mixer
Playback Mixer
Would the following do the trick?"
I confirm that this solves the audio problems I was having.
Signed-off-by: Jonas Bonn <jonas.bonn@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dell Inspiron 1525 seems to have a buggy BIOS setup and screws up
the recent codec parser, as reported by Oleksandr Natalenko:
http://lkml.org/lkml/2008/9/12/203
This patch adds the working model, dell-3stack, statically.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
The error path in cs4270_probe/cs4270_remove is pretty broken:
* If cs4270_probe fails, codec is leaked.
* If snd_soc_register_card fails, cs4270_i2c_driver stays registered.
* If I2C support is enabled but no I2C device is found, i2c_del_driver
is never called (neither in cs4270_probe nor in cs4270_remove.
Fix all 3 problems by implementing a clean error path in cs4270_probe
and jumping to its labels as needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Conversion to new-style i2c driver missed the error path of the
probe function. Fix it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Timur Tabi <timur@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Update the CS4270 ALSA device driver to use the new-style I2C interface.
Starting with the 2.6.27 PowerPC kernel, I2C devices that have entries in the
device trees can no longer be probed by old-style I2C drivers. The device
tree for Freescale MPC8610 HPCD has included an entry for the CS4270 since
2.6.25, but that entry was previously ignored by the PowerPC I2C subsystem.
Since that's no longer the case, the best solution is to update the CS4270
driver to a new-style interface, rather than try to revert the behavior of
new PowerPC I2C subsystem.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The power_mutex lock in snd_pcm_drop may cause a possible deadlock
chain, and above all, it's unneeded. Let's get rid of it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCM and rawmidi open callbacks have a lock against card->controls_list
but it takes a wrong one, card->controls_rwsem, instead of a right one
card->ctl_files_rwlock. This patch fixes them.
This change also fixes automatically the potential deadlocks due to
mm->mmap_sem in munmap and copy_from/to_user, reported by Sitsofe
Wheeler:
A: snd_ctl_elem_user_tlv(): card->controls_rwsem => mm->mmap_sem
B: snd_pcm_open(): card->open_mutex => card->controls_rwsem
C: munmap: mm->mmap_sem => snd_pcm_release(): card->open_mutex
The patch breaks the chain.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
this fixes typo in wm9712 codec which prevents it from registering all audio
routes (and thus working correctly). Please consider applying.
(Tested and works on palmtx, palmld and palmt5)
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mark Brown <brooie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Probing non-existing device causes Oops with snd-opti93x driver
due to NULL access in the destructor of the error path.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Rene Herman <rene.herman@gmail.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Tested-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Ingo Molnar <mingo@elte.hu>
This allows pre and post event hooks to be provided for PGA widgets.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The DAPM event callback code has many layers of indentation, taking it
over 80 columns. Refactor the code to give less indentation in order to
avoid checkpatch issues on further changes and exploding indentation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
communicate the ES137x PCI device to the AC97 code for its
subsys_vendor/device values
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It seems NVidia and other hardwares require the alignment for period
update timing. For satisfying this condition, align the position
adjustment for delayed wake-up to the initial bdl_pos_adj value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TX idleness isn't tested, but RX twice. PSC is not disabled when TX is idle
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-2.6.27' of git://git.infradead.org/users/dwmw2/firmware-2.6: (64 commits)
firmware: convert sb16_csp driver to use firmware loader exclusively
dsp56k: use request_firmware
edgeport-ti: use request_firmware()
edgeport: use request_firmware()
vicam: use request_firmware()
dabusb: use request_firmware()
cpia2: use request_firmware()
ip2: use request_firmware()
firmware: convert Ambassador ATM driver to request_firmware()
whiteheat: use request_firmware()
ti_usb_3410_5052: use request_firmware()
emi62: use request_firmware()
emi26: use request_firmware()
keyspan_pda: use request_firmware()
keyspan: use request_firmware()
ttusb-budget: use request_firmware()
kaweth: use request_firmware()
smctr: use request_firmware()
firmware: convert ymfpci driver to use firmware loader exclusively
firmware: convert maestro3 driver to use firmware loader exclusively
...
Fix up trivial conflicts with BKL removal in drivers/char/dsp56k.c and
drivers/char/ip2/ip2main.c manually.
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (241 commits)
[ARM] 5171/1: ep93xx: fix compilation of modules using clocks
[ARM] 5133/2: at91sam9g20 defconfig file
[ARM] 5130/4: Support for the at91sam9g20
[ARM] 5160/1: IOP3XX: gpio/gpiolib support
[ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.
[ARM] 5084/1: zylonite: Register AC97 device
[ARM] 5085/2: PXA: Move AC97 over to the new central device declaration model
[ARM] 5120/1: pxa: correct platform driver names for PXA25x and PXA27x UDC drivers
[ARM] 5147/1: pxaficp_ir: drop pxa_gpio_mode calls, as pin setting
[ARM] 5145/1: PXA2xx: provide api to control IrDA pins state
[ARM] 5144/1: pxaficp_ir: cleanup includes
[ARM] pxa: remove pxa_set_cken()
[ARM] pxa: allow clk aliases
[ARM] Feroceon: don't disable BPU on boot
[ARM] Orion: LED support for HP mv2120
[ARM] Orion: add RD88F5181L-FXO support
[ARM] Orion: add RD88F5181L-GE support
[ARM] Orion: add Netgear WNR854T support
[ARM] s3c2410_defconfig: update for current build
[ARM] Acer n30: Minor style and indentation fixes.
...
This includes PXA work up to the SPI changes for the initial merge,
since e172274ccc depends on the SPI
tree being merged.
Conflicts:
arch/arm/configs/em_x270_defconfig
arch/arm/configs/xm_x270_defconfig
kcalloc is supposed to be called with the count as its first argument and the
element size as the second.
Both arguments are size_t so does not affect correctness. This callsite is
during module_init and therefore not performance critical. Another patch will
optimize the case when the count is variable but the size is fixed.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds a new ALSA driver for the audio device found inside
most of the SGI O2 workstation. The hardware uses a SGI custom chip,
which feeds a AD codec chip.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
We don't want to see ASoC platform menus for other non selected
architectures in our config.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds a new ALSA driver for the audio device found inside
many older SGI workstation (Indy, Indigo2). The hardware uses a SGI
custom chip, which feeds two codec chips, an IEC chip and a synth chip.
Currently only one of the codecs is supported. This driver already has
the same functionality as the HAL2 OSS driver and will replace it.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fixed the missing initialization for unsolicited events on
Cx5045 micsense model.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added volume controls for the analog PC Beep on 92hd71bxx codecs.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix a const pointer usage warning in the Digigram miXart soundcard driver. A
const pointer is being passed to copy_from_user() to load the firmware into.
This is okay in this case because the function has allocated the firmware
struct itself, but the const qualifier is part of the firmware struct - so the
patch casts the const away.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix a const pointer usage warning in the Digigram pcxhr compatible soundcard
driver. A const pointer is being passed to copy_from_user() to load the
firmware into. This is okay in this case because the function has allocated
the firmware struct itself, but the const qualifier is part of the firmware
struct - so the patch casts the const away.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix a const pointer usage warning in the Digigram VX soundcard driver. A
const pointer is being passed to copy_from_user() to load the firmware into.
This is okay in this case because the function has allocated the firmware
struct itself, but the const qualifier will be part of the firmware
struct - so the patch casts the const away.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Standardise both in-kernel and loaded firmware to be stored as
little-endian instead of host-endian.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The maestro3 driver is byte-swapping its firmware to be host-endian in
advance, when it doesn't seem to be necessary -- we could just use
le16_to_cpu() as we load it.
Doing that means that we need to switch the in-tree firmware to be
little-endian too.
Take the least intrusive way of doing this, which is to switch the
existing snd_m3_convert_from_le() function to convert _to_ little-endian
instead, and use it on the in-tree firmware instead of the loaded
firmware. It's a bit suboptimal but doesn't matter much right now
because we're about to remove the special cases for the in-tree version
anyway.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
As reported and tested by an RedHat customer, HP dc7600 with pci sub IDs
0x103c/0x3011 works with the hp-3013 model and not with the hp only model.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock
speed.
We created a new board for this device but based the chip support
directly on 9260 files with little updates.
Here is the chip page on Atmel wabsite:
http://atmel.com/dyn/products/product_card.asp?part_id=4337
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We have to restrict the quirk to interface 0 because the second
interface is not MIDI but HID. Additionally, this product ID is used
by all four KX models, so it is better to read the product name from
the device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
This patch is for the Yamaha USB MIDI controller KX49.
http://www.yamahasynth.com/products/kx/index.html
It has a 3-port MIDI interface and an HID interface (it has a tiny
keyboard subset).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
A bunch of things in alsa depend on CONFIG_KMOD,
use CONFIG_MODULES instead where the dependency
is needed at all.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix a const to non-const pointer assignment warning in the Digigram VXpocket
sound driver.
This may be due to patch 0aa4937648b91e9e6d3879b2cbeaa5f0c9863ac0.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix a const pointer usage warning in the Digigram VX soundcard driver. A
const pointer is being passed to copy_from_user() to load the firmware into.
This is okay in this case because the function has allocated the firmware
struct itself, but the const qualifier is part of the firmware struct - so the
patch casts the const away.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This adds support for the recent DAI struct merge and new DAPM pin API.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds a missing " that was recently introduced (removed)
in the DAI struct merge patch series.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds several functions for DAI control and config
and replaces the current method of calling function pointers within
the DAI struct within the machine drivers.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds several functions for DAI control and config
and replaces the current method of calling function pointers within
the DAI struct.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
An gpio_mask value was defined twice needlessly.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Explicit DAPM syncs are likely to cause DAPM state updates, as are mixer
and mux configuration changes, so display the DAPM status after them too.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
DAPM contains debug output controlled by a DAPM_DEBUG macro. Change this
to be controlled by the standard DEBUG, dropping the custom dbg() macro
as we go.
Also fix the error printed when configuring an unknown pin to be an
unconditionally displayed error rather than debug output.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch merges struct snd_soc_codec_dai and struct
snd_soc_cpu_dai into struct snd_soc_dai for the SuperH platform.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch merges struct snd_soc_codec_dai and struct
snd_soc_cpu_dai into struct snd_soc_dai for the S3C24xx platform.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch merges struct snd_soc_codec_dai and struct
snd_soc_cpu_dai into struct snd_soc_dai for the PXA platform.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch merges struct snd_soc_codec_dai and struct
snd_soc_cpu_dai into struct snd_soc_dai for the Omap platform.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch merges struct snd_soc_codec_dai and struct
snd_soc_cpu_dai into struct snd_soc_dai for the Freescale PPC platform.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch merges struct snd_soc_codec_dai and struct
snd_soc_cpu_dai into struct snd_soc_dai for the codec drivers.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch merges struct snd_soc_codec_dai and struct
snd_soc_cpu_dai into struct snd_soc_dai for the DaVinci platform.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch merges struct snd_soc_codec_dai and struct
snd_soc_cpu_dai into struct snd_soc_dai for the AT91 platform.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch series merges struct snd_soc_codec_dai and struct
snd_soc_cpu_dai into struct snd_soc_dai for AT32 platform.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch series merges struct snd_soc_codec_dai and struct
snd_soc_cpu_dai into struct snd_soc_dai in preparation for further
ASoC v2 patches.
This merger removes duplication in both DAI structures and simplifies
the API for other users.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the model entry (model=lenovo) for Lenovo N3000 N200 laptop
with ALC861-VD. Reference below:
https://bugzilla.novell.com/show_bug.cgi?id=406425
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
DAPM supports adding a compile time configurable delay to the widget power
sequences, aiding diagnosis of problems with pops and clicks being
generated during them. This patch converts this to be configurable at run
time via a sysfs file.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Replace 'snd_ac97_write' with snd_ac97_write_cache' in pacth_ucb1400 to allow
proper codec wakeup.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Toshiba Satellite P105 with cx5045 has no HP pin but only a
speaker pin and does the speaker-muting on hardware.
Thus the matching model is laptop-micsense.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the missing SSID of Thinkpad Z60m for model=thinkpad with
AD1981HD.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
ALC883 medion model doesn't unmute the proper amps so no output can be heard.
Replaced the mute switches to behave just like other models.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Some laptops don't like PR3 powerdown. Do PR3 powerdown only
for the real power-saving.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sound/soc/pxa/tosa.c contains dependencies on parts that never
ever hit mainline. Replace them with current support for tc6393xb.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some machines with Cx5045 seem to have no problem with the volume
over 0dB on NID 0x17. Disable amp overrides for other devices but HP.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
YDSXGR_BUF441OUTVOL register isn't initialized properly. This may lead to
a silent output at full volume of unchanged "Wave Playback Volume".
http://bugzilla.kernel.org/show_bug.cgi?id=10963
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
MacBook 3.1 is compatible with model=mbp3.
Added the codec SSID 10b6:3600.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
AIC33 and AIC34 codecs in TLV320AIC3x family support digital microphone
input. When enabled, the codec ADC takes bitstream input to low-pass
filter from GPIO2 instead of its own delta-sigma modulator while providing
oversampling clock through GPIO1.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Those two serial data interface control register bits have also other
functions and they can be set before aic3x_set_dai_fmt is called.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This generic register modifier widget is for updating multiple codec
register bits at once when the widget changes its power state.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Several ASoC codec drivers use custom macros equivalent to the standard
pr_ macros, most of which are not actually used. Replace these custom
macros with the standard ones.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The AK4535 codec is included in some HP iPAQ systems.
This driver was originally written by Richard Purdie and with some bug
fixes from Milan Plzik. While out of tree it has also had some
mechanical updates for new APIs and current best practices from Liam
Girdwood, Graeme Gregory and Mark Brown.
Signed-off-by: Richard Purdie <richard@openedhand.com>
Signed-off-by: Milan Plzik <milan.plzik@gmail.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Graeme Gregory <gg@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
- fix problem with codec register 0x6a being write-only
by adding a software shadow register
(caused annoying noise after module loading due to _toggling_
between gameport and audio bits instead of configuring them properly)
- rename several "Wave" mixer controls to "PCM", since this is
what Wine and several other apps are looking for (IOW, _requiring_)
and this is what AC97 specs use as naming, too,
thus I'd guess it's what these controls are
- cleanup, small optimizations
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Stop the S/PDIF DMA engine and output when the device is told to pause.
It will keep on looping the current buffer contents if this isn't done.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Tested-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add the SSID for the "Fujitsu Siemens Amilo M1451G" laptop to
patch_realtek.c , so that it uses ALC880_FUJITSU by default.
Signed-off-by: Travis Place <wishie@wishie.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the SSID of a known iMac 24" to automatically use
ALC885_IMAC24 quirk.
Signed-off-by: Travis Place <wishie@wishie.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
snd_assert() in save_mixer() and restore_mixer() in sb_mixer.c is
just wrong. The debug code wasn't tested at all, obviously...
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The irq handler may be called before the proper initialization of hardware.
Call snd_aw2_saa7146_setup() before the irq handler registration.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AC_VERB_GET_DIGI_CONVERT_2 isn't actually implemented but reserved.
The whole SIC bits are returned from DIGI_CONVERT_1.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix sound/soc build failure when CONFIG_PM=n:
linux-next-20080617/sound/soc/soc-core.c:829: error: 'soc_resume_deferred' undeclared (first use in this function)
soc3.out:make[3]: *** [sound/soc/soc-core.o] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added an entry for another MSI K8N Diamond mobo with SSID 1102:1009.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Don't create mixer volume elements for Headphone and Speaker if they
use the same DAC as normal line-outs on AD1988. Otherwise the amp
value gets screwed up, e.g.
https://bugzilla.novell.com/show_bug.cgi?id=398255
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix the Freescale MPC8610 HPCD sound driver so that it programs the DMACR
and PMUXCR registers in the global utilities correctly.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Check that model->control_filter is set before trying to call it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use bdl_pos_adj=32 as default except for Intel hardwares confirmed
to work with bdl_pos_adj=1. Looks like ATI and NVidia require this
higher value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
On OpenMoko soc-audio resume is taking 700ms of the whole resume time of
1.3s, dominated by writes to the codec over I2C. This patch shunts the
resume guts into a workqueue which then is done asynchronously.
The "card" is locked using the ALSA power state APIs as suggested by
Mark Brown.
[Added fix for race with resume to suspend and fixed a couple of nits
from checkpatch -- broonie.]
Signed-off-by: Andy Green <andy@openmoko.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
To provide added robustness in case an AC97 controller reads back all
zeros in error cases check for an exact match when testing to see if
resets have brought the codec back.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added support for new family of IDT codecs.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
snd_ctl_elem_read() and snd_ctl_elem_write() are no longer used by
any other drivers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Sort stac9205_cfg_table in the order of id numbers, and removed the
duplicated (obsoleted) entries for 0x01fc and 0x01fd. This doesn't
change the driver behavior since the old entries are all secondary.
The duplication occured due to commit dfe495d0, and the old entries
were introduced by commit ae0a8ed8.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Mike Montour <mail@mmontour.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Mike Montour <mail@mmontour.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This allows per-DAI initialisation to be done by the CPU DAI drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Ensure that DAIs are prototyped in the codec drivers that define them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
ASoC codec drivers frequently set the register cache size using sizeof()
rather than ARRAY_SIZE(). For tlv320aicx either is correct since the
registers are 8 bit but update to use ARRAY_SIZE() for clarity.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The register cache size is used by the codec_reg sysfs file which works in
terms of the register cache access functions rather than in terms of raw
access to the cache so the size specified needs to be in terms of the
number of elements.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The register cache size is used by the codec_reg sysfs file which works in
terms of the register cache access functions rather than in terms of raw
access to the cache so the size specified needs to be in terms of the
number of elements.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch converts the Opti93x driver to use
the cs4231 library instead of duplicating the code.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Tested-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds support for WSS compatible Opti93x
codec to the cs4231-lib.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Tested-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The pending IRQ handling is a very hackish workaround and should be
avoided as much as possible via a larger bdl_pos_adj option value.
Put a warning message if this situation occurs so that the user may have
a chance to notice that something is wrong.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
ATI SB controllers seem to report the DMA ahead in the amount of FIFO.
Thus bdl_pos_adj should be 32 for them as default.
Also, the default value is set to -1, which means to make the driver
to choose the appropriate value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The option bdl_pos_adj should be provided for each card instance instead of
a global one because the value depends rather on each controller-chip.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
position_fix=3 is the option to correct the DMA position with the
FIFO size. But, it never worked correctly, and we have now more other
workarounds for the DMA position fixes. Thus better to remove it.
Also, change POS_FIX_NONE to POS_FIX_LPIB to represent its real role
better.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added a new option, bdl_pos_adj, to adjust the delay of IRQ-wakeup
timing.
Most HD-audio hardwares have a problem that a BDL IRQ is issued before
actually the data and the DMA pointer are updated.
We have already a mechanism to force to delay snd_pcm_period_elapsed()
calls via workq, but this costs much CPU, and typically the delay is
within one sample. Thus, it's more clever to adjust the BDL entries
instead.
The new option adds the size of the delay in frames. As default,
it's set to 1 -- that is, one sample delay. Even the hardware is
really correct, one sample delay is relatively harmless in comparison
with reporting wrong positions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch contains the following cleanups:
- make the following needlessly global functions static:
- dmasound_core.c: get_afmt_string()
- dmasound_paula.c: dmasound_paula_init()
- dmasound_q40.c: dmasound_q40_init()
- remove the following unused global variable:
- dmasound_core.c: software_input_volume
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the missing GFP_ATOMIC to page_alloc when called with GFP_DMA.
GFP_KERNEL often results in stalls for ZONE_DMA, so GFP_ATOMIC is more
prgmatic.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
I have Toshiba dynabook SS RX1 and this patch adds that support.
Signed-off-by: Akio Idehara <zbe64533@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch fixes silenced output from the Opti930.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The power_save option was set as boot although it was meant to be a
timeout value like the same option of snd-hda-intel originally.
Now fixed to the same style.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds support for Master Left Inv Switch on wm9711.
At least required to drive the mono speaker on the PXA270 platfrom
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
I think that hda_verb array must have "terminator (empty array)".
But alc262_sony_unsol[] does not have it.
And it causes gcc-4.3's buggy behavior
with snd_hda_sequence_write().
Signed-off-by: Akio Idehara <zbe64533@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch makes the needlessly global snd_dbri_proc() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since USB_EHCI_SPLIT_ISO is now unconditionally enabled the
#ifndef CONFIG_USB_EHCI_SPLIT_ISO became wrong.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After the removal of the sequencer instrument layer SND_GUS_SYNTH was
no longer used.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Attached is a revised version of my patch to add AT32 to ASoC. This cleans
most of the style issues associated with the previous patch. Also fixes an
issue with the playpaq_wm8510.c code depending on a non-released patch to th
AT32 portmux support.
Patch is against 2.6.24.3.atmel.3 kernel, the latest AVR32 kernel Atmel has
released, with the linux-2.6-asoc patches from when v2.6.24 was tagged also
applied.
[Fixed up minor checkpatch issues and updated for current kernels -- broonie]
Signed-off-by: Geoffrey Wossum <gwossum@acm.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The WM8990 is a highly integrated ultra-low power hi-fi codec designed
for handsets rich in multimedia features such as mobile TV, digital
audio playback and gaming.
The bulk of this driver was written by Liam Girdwood with some
additional development and updates for new ASoC APIs by me.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The WM8510 is a mono CODEC with speaker driver optimised for telephony
applications, featuring:
- 16/20/24/32 bit audio at data rates between 8kHz and 48kHz
- On-chip PLL
- Dual microphone inputs
This driver was originally written by Liam Girdwood with updates from
Brett Saunders, Geoffrey Wossum and myself.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Brett Saunders <breton.saunders@ntlworld.com>
Signed-off-by: Geoffrey Wossum <geoffrey@pager.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make the hw volume buttons work correctly on some HP OmniBook laptops.
The original quirk was apparently applied a bit too early and it was
also lacking some critial register writes. This improved sequence was
discovered by trial and error (like the original sequence). Tested and
found working on OB500 and OB6000 laptops.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It turned out that some ICH9-based boards use SD3 for the audio codec
where the current driver code doesn't probe. Since we have a better
codec slot check now, it must be safe to increase this to 4.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These two motherboards's pin configuration are not covered by driver.
I wrote a new model to support them.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the Linux kernel is compiled with CONFIG_DEBUG_SHIRQ=y,
the Soundblaster Audigy2 ZS Notebook PCMCIA card causes the
system hang during boot (udev stage) or when the card is hot-plug.
The CONFIG_DEBUG_SHIRQ flag is by default 'y' with all Fedora
kernels since 2.6.23. The problem was reported as
https://bugzilla.redhat.com/show_bug.cgi?id=326411
The issue was hunted down to the snd_emu10k1_create() routine:
/* pseudo-code */
snd_emu10k1_create(...) {
...
request_irq(... IRQF_SHARED ...) {
register the irq handler
#ifdef CONFIG_DEBUG_SHIRQ
call the irq handler: snd_emu10k1_interrupt() {
poll I/O port // <---- !! system hangs
...
}
#endif
}
...
snd_emu10k1_cardbus_init(...) {
initialize I/O ports
}
...
}
The early access to I/O port in the interrupt handler causes
the freeze. Obviously it is necessary to init the I/O ports
before accessing them. This patch moves the registration of
the irq handler after the initialization of the I/O ports.
Signed-off-by: Jaroslav Franek <jarin.franek@post.cz>
Acked-by: James Courtier-Dutton <James@superbug.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use quirk table to assign ALC268_TOSHIBA to COMPAL IFL90/JFL-92 laptops.
No analog output on autoprobe.
Signed-off-by: Tony Vroon <tony@linx.net>
Tested-by: Guri <gurashka@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On Audigy2 Platinum, the Analog/Digital mixer switch is inverted.
https://bugzilla.novell.com/show_bug.cgi?id=396204
The patch adds a simple workaround.
There might be another device requiring a similar fix, too (or fix for
audigy2 generically), but right now I fix only the known broken one.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mic pins are wrongly assigned on AD1884A mobile model.
The mic handling is fixed for the automatic mic selection, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Simplify the page allocation of emu10k1 driver for emux synth support.
Since these pages aren't be necessarily coherent, we can avoid
expensive DMA-coherent routines.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ak4531 module is used only by ens1370 driver (and unlikely that
any other will use it ever). Let's make it local to ens1370.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The UDA1380 codec is used by the HTC Magician and a number of Samsung
reference boards.
This driver has had a long out of tree history, having originally been
written by Giorgio Padrin and converted to ASoC by Richard Purdie.
Since conversion to ASoC most of the work on the driver has been done by
Philipp Zabel with some review and updates for new APIs by Liam Girdwood
and Mark Brown.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The SOC_DOUBLE_S8_TLV control type was originally implemented in the
UDA1380 driver by Philipp Zabel and was moved into the core by me.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix and improve the slots option handling. The sound core tries to
find the slot with the given module name first and assign if it's
still available. If all pre-given slots are unavailable, then try
to find another free slot.
Also, when a module name begins with '!', it means the negative match:
the slot will be given for any modules but that one.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixed EAPD and COEF setups for Realtek ALC662/663, 660-VD and 888 codecs.
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Show more exact codec chip name in the PCM stream name strings.
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the support of ALC663 codec, including specific models for
ASUS M51VA, ASUS G71V, ASUS H13 and ASUS G50V.
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the missing PCI ID for ICH9 controller (8086:2911)
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace CONFIG_SND_DEBUG_DETECT with CONFIG_SND_DEBUG_VERBOSE to
represent its meaning more better. This config isn't provided only
for the detection but for more verbose debug prints in general.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The kconfig items related with AC97-powersave must be outside the
CONFIG_SND_PCI range. And it'd be better together with CONFIG_SND_AC97.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added entry into usbquirks.h to recognize Roland SonicCell sound module by
mostly duplicating the entry for the Roland SH-201. USB MIDI works just fine,
though the USB audio is a little unreliable (but still works well enough).
Signed-off-by: Chris Mennie <camennie@alumni.uwaterloo.ca>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix capture mute widget for STAC9250/9251 codecs. The widget 0x09
has no mute but 0x14 does actually.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This solves the problem with mixers wrongly displaying the PWM freq.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added IDs for the Foxconn P35AX-S mainboard to patch_realtek.c, so
that ALC883_6ST_DIG is used by default.
Signed-off-by: Travis Place <wishie@wishie.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We get quite noisy output on the right channel on VT1708 codec
when 24bit samples are used. Suppress the 24bit support until any
real fix is found.
https://bugzilla.novell.com/show_bug.cgi?id=390473
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added a config table entry for the ASUS P5K-E/WIFI-AP mainboard (ID
1043:8227) to use AD1988_6STACK_DIG
Signed-off-by: Travis Place <wishie@wishie.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is a race from when a device is created with device_create() and
then the drvdata is set with a call to dev_set_drvdata() in which a
sysfs file could be open, yet the drvdata will be NULL, causing all
sorts of bad things to happen.
This patch fixes the problem by using the new function,
device_create_drvdata().
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The VT1724 MIDI port is not MPU-401 compatible; remove the hacks that
try to make the MPU-401 library work with it, and just use some simple
device-specific code.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Pavel Hofman <pavel.hofman@insite.cz>
Corrected the model assignment for the ASUS P5GD1 w/SPDIF after reports of
surround sound not being possible.
Signed-off-by: Travis Place <wishie@wishie.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change HRTIMER_CB_IRQSAFE to HRTIMER_CB_SOFTIRQ,
as suggested by Thomas Gleixner.
That solves the lock dependancy reported in
Bug #10701.
That also allows to call hrtimer_start()
directly, tasklet "stupid hack" removed.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When timer ticks are disabled when calling
sound/soc/s3c24xx/s3c24xx-i2s.c:s3c24xx_snd_lrsync
and the LR signal never happens, we loop forever.
This has been observed in the following call chain:
snd_pcm_common_ioctl1 -> snd_pcm_action_lock_irq ->
snd_pcm_action_single
-> snd_pcm_do_resume -> soc_pcm_trigger -> s3c24xx_i2s_trigger
The patch below changes the timeout mechanism to use udelay, which
doesn't need timer ticks.
Signed-off-by: Werner Almesberger <werner@openmoko.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Currently the ASoC core configures the bias levels in the system using
a callback on codecs and machines called 'dapm_event', passing it PCI
style power levels as SNDRV_CTL_POWER_ constants. This is more obscure
than it needs to be and has caused confusion to driver authors,
especially given that DAPM is also performing power management.
Address this by renaming the callback function to 'set_bias_level' and
using constants explicitly representing the off, standby, pre-on and on
states which DAPM transitions through.
Also unexport the API for setting bias level: there are currently no
in-tree users of this API other than the core itself and it is likely
that the core would need to be extended to cater for any users.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The overwhelming majority just say 'initial version' anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Many HD-audio controllers seem inaccurate about the IRQ timing of
PCM period updates. This has caused problems on audio quality; e.g.
JACK doesn't work with two periods.
This patch fixes the problem by checking the current DMA position
at IRQ handler and delays the period-update via a workq if it's
inaccurate.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
- figured out 'Digital(ly) Enhanced Game Port' functionality,
implemented support for it (eliminating gameport polling overhead)
- removed optional joystick activation, gameport now enabled unconditionally,
since we now support it via the PCI I/O space, not via conflict-prone
legacy I/O (which I was thus able to DISABLE now)!
- fix playback bug (a muted wave output would get unmuted upon start of
playback, of course this is not what we want, thus remember mute state)
- implement partial power management: when idle, lower clock rate and disable
codec (reduced noise!), and disable gameport circuit when unused
- instantiate OPL3 timer, too
- much better implementation of snd_azf3328_mixer_write_volume_gradually()
- slightly optimized interrupt handling
- lots of cleanup
This time, I also found a way to verify proper OPL3 operation
via MIDI file playback (emulation via synth hardware).
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Use gpiolib since it is now available for OMAPs. Change also references to
HW version RX44 to product name N810.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Frank Mandarino <fmandarino@endrelia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
ASoC codecs and machine drivers that use DAPM routes all cut'n'paste a
loop iterating over a null terminated array of routes. Factor out this
into a bulk registration function, improving the error reporting for
most users, and deprecate the old API to help out of tree users pick up
the changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Graeme Gregory <graeme@openmoko.org>
Cc: Frank Mandarino <fmandarino@endrelia.com>
Cc: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Most SoC drivers cut'n'paste a loop iterating over an array to register
their DAPM controls. Provide a function they can call instead.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Graeme Gregory <graeme@openmoko.org>
Cc: Frank Mandarino <fmandarino@endrelia.com>
Cc: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add a constraint for the period time so that there are less than ten
seconds between interrupts so that ALSA does not assume that the device
is dead.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Introduce symbols for the buffer/period size constraints so that their
limits and relationships become clearer.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Move the setting of the output enable GPIO bit to a separate function.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Create separate functions for the code that initializes the hardware, as
opposed to initializing internal driver state, so that they can be
reused for resume support.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
When initializing the DAC volume registers, we can just use the generic
volume update functions instead of setting the registers manually.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Save the written values of all CMI8788 and AC97 registers and of some of
the DAC/ADC registers so that it is possible to restore the register
state later.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Remove another magic number - add a symbol for the size of the PCI I/O
range.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Adjust the MODULE_LICENSE strings to properly reflect the actual license.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The hack for dma_alloc_coherent() is no longer needed on 2.6.26 since
the base code was improved.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Tim Niemeyer <reddog@mastersword.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This adds a hook to read the power state of a DAPM widget, I use this
in the gta02 driver to expose certain DAPM widgets in the mixer for
ease of audio routing.
Signed-off-by: Graeme Gregory <graeme@openmoko.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds support for AIC3x GPIO lines. They can be configured for
many possible functions as well as be driven manually. I also introduced
i2c read functionality since the GPIO state register has to be read from
hardware every time and can not be served from cache.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch cleans up the clocking setup for aic3x codecs. It drops the
dividers table and determines the PLL control values programatically.
Under certain conditions, the PLL is disabled entirely which could save
some power.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
It appears that alsa allows a sound buffer with size not
evenly devided by the period size. This triggers a warning in
snd-pcsp and floods the log. As a quick fix, the warning should
be disabled.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Considering all the feedbacks I got, depending snd-pcsp on
CONFIG_EXPERIMENTAL looks like the only safe way to get out
of all the troubles at one go. :)
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The attached patch adds back the compatibility code, allowing the
driver to work with older alsa-libs.
The removal was premature, it breaks the real-life configs.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the warning text to the help of snd-pcsp about the possible problem
with this driver so that user can know of the problem in advance.
Also, removed the obsoleted text about ancient pc-speaker patch in
CONFIG_SOUND help.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix this typo and avoid similar errors by using ARRAY_SIZE macro.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the hardware wavetable synthesizer of an Creative SB Audigy or SB
Live! card (with emu10k chip) receives the MIDI SOFT_PEADAL-press event
(?? 67 127) the appropriate voice is attenuted. Unfortunately when the
pedal is released (event ?? 67 0) the voice does not get it's original
volume again.
Boolean MIDI controls should interpret 0..63 as false and 64..127 as true.
Thanks to Clemens Ladisch for review and correction.
Original patch from "Uwe Kraeger" <uwe_debbug@arcor.de>
Submitted to http://bugs.debian.org/474312
Signed-off-by: maximilian attems <max@stro.at>
Cc: uwe_debbug@arcor.de
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
drivers/md/raid10.c:889:17: warning: Using plain integer as NULL pointer
drivers/media/video/cx18/cx18-driver.c:616:12: warning: Using plain integer as NULL pointer
sound/oss/kahlua.c:70:12: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Found these two bugs while browsing through the code. The first one is
a cut-n-paste bug, instead of disabling the clock when request_irq()
fails, it enabled it once more. The second one fixes a debug printout,
AT91_SSC_IER is write only, AT91_SSC_IMR is readable (the printed string
actually says imr).
Frank Mandarino was busy so he asked me to send these to this list.
/Patrik
Signed-off-by: Patrik Sevallius <patrik.sevallius@enea.com>
Acked-by: Frank Mandarino <fmandarino@endrelia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There's more checkpatch stuff to fix in the driver, this just fixes the
minimum required for the following patch to be clean.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
fix pcspkr dependancies: make the pcspkr platform
drivers to depend on a platform device, and
not the other way around.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
CC: Vojtech Pavlik <vojtech@suse.cz>
CC: Michael Opdenacker <michael-lists@free-electrons.com>
[fixed for 2.6.26-rc1 by tiwai]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
S3C2410 i2s driver currently manages only i2s protocol (and not left
justified one) and slave mode.
With this small patch, other modes are possible.
Signed-off-by: Davide Rizzo <davide@elpa.it>
Acked-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
S3C2410 pcm doesn't work.
s3c2410_dma_request() now returns the channel number and not 0 if OK.
Signed-off-by: Davide Rizzo <davide@elpa.it>
Acked-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On boards with VT1617A codec, the sound disappears suddenly.
This looks like a problem with HPE-bit control that is supposed to be
set in patch_vt1617a(). However, on such problematic hardwares, the
bit is actually reset mysteriously.
The patch adds a workaround for the wrong quirk.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
FM801-tea575x tuner has a reverse selection to V4L1 and this causes
nasty dependency problems.
The patch simplifies the dependency with a normal
"depends on VIDEO_V4L1". This decreases the usability but fixes bugs,
yeah. If any better feature like "requires" is introduced to kbuild
in future, we'll be able to switch it...
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/drivers/pcsp/pcsp.c: In function 'pcsp_suspend':
sound/drivers/pcsp/pcsp.c:201: error: implicit declaration of function 'snd_pcm_suspend_all'
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
CC: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Patch taken from the openmoko bugtracker
http://bugzilla.openmoko.org/cgi-bin/bugzilla/show_bug.cgi?id=781
This patch adds Suspend/Resume and Shutdown support for the lm4857 to
the driver.
Signed-off-by: Graeme Gregory <graeme@openmoko.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I have moved workplaces since I originally wrote this driver so update
the contact info for new employers.
Signed-off-by: Graeme Gregory <graeme@openmoko.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clean up a few issues with the file that checkpatch noted, no functionality
changes.
Signed-off-by: Graeme Gregory <graeme@openmoko.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add common OMAP ASoC drivers and machine driver for Nokia N810. Currently
supported features are:
- Covers OMAPs from 1510 to 2420
- Common DMA driver
- DAI link driver using McBSP port in I2S mode
- Basic machine driver for Nokia N810
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some drivers have duplicated unlikely() macros. IS_ERR() already has
unlikely() in itself.
This patch cleans up such pointless code.
Signed-off-by: Hirofumi Nakagawa <hnakagawa@miraclelinux.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use proc_create() to make sure that ->proc_fops be setup before gluing PDE to
main tree.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove proc_root export. Creation and removal works well if parent PDE is
supplied as NULL -- it worked always that way.
So, one useless export removed and consistency added, some drivers created
PDEs with &proc_root as parent but removed them as NULL and so on.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sound boards with VT1724 and compatible chips may lock up when
MPU401 is accessed together with the PCM streaming.
This patch fixes the problem.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Also change some if (x == NULL) to if (!x).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
