Add Migo-R specific platform data for on-chip sh7722 CEU and ov772x camera.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
fix the problem that cannot boot using uImage when PAGE_SIZE is
8kbyte or 64kbyte.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Without this patch, signals sent during architecture specific signal
handling (typically as a result of the user's stack being inaccessible)
are ignored.
This is the SH version of commit c3ff8ec31c
which was for the i386.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use clk_always_enable() on the sh7343 processor and in the board code
for Solution Engine 7343. Remove duplicate MSTPCR register definitions.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use clk_always_enable() on the sh7722 processor and in the board code
for Migo-R and Solution Engine 7722. Remove duplicate MSTPCR register
definitions.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use clk_always_enable() on the sh7723 processor and in the ap325rxa
board code. Remove duplicate MSTPCR register definitions.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Show all clocks in /proc/clocks, and also show if they are enabled or
disabled. This is useful to show MSTPCR bits on SuperH Mobile processors.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This code makes sh7343 share the sh7722 clock code. Instead of just using
the good and very old sh7343 clock implmentation, switch to the new MSTPCR
enabled clock code. SIU clocks are disabled on sh7343 for now.
With this change all SuperH Mobile devices now use the same clock code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Handle module stop clock bits in MSTPCRn through the clock framework.
The clocks are named after the bits in the data sheet. The association
between bit number and hardware block is processor specific.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit 1ea0704e0d
(mm: add a ptep_modify_prot transaction abstraction)
triggered on sh build errors like the following:
<-- snip -->
...
CC arch/sh/mm/pg-sh4.o
cc1: warnings being treated as errors
include2/asm/pgtable.h:139: error: 'ptep_get_and_clear' declared inline after being called
include2/asm/pgtable.h:139: error: previous declaration of 'ptep_get_and_clear' was here
make[2]: *** [arch/sh/mm/pg-sh4.o] Error 1
<-- snip -->
Since there's no good reason for marking these global functions as
"inline" this patch therefore removes the inline's.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds initial support for the Renesas R0P7785LC0011RL board.
This patch supports 29bit address mode only.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds physically contiguous memory chunks to the UIO devices.
The same strategy can be used in the future for the CEU as well.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch exports the VPU, VEU(1) and VEU(2) blocks of the sh7366
to user space using the uio_pdrv_genirq platform driver.
While at it, fix up the VEU(2) interrupt vector.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch exports the VPU, VEU2H0 and VEU2H1 blocks of the sh7723
to user space using the uio_pdrv_genirq platform driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch exports the VPU and VEU blocks of the sh7722 to user space
using the uio_pdrv_genirq platform driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch exports the VPU and VEU blocks of the sh7343 to user space
using the uio_pdrv_genirq platform driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is
By sh2
- Remove duplicate code
- Reduce stack usage
- Cleanup and little optimize
By sh2a
- Add missing handler(256 to 511)
- Use sh2a instructions handler
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
updated the following codes for Solution Endine 7343:
- fix compile error in arch/sh/boards/se/7343/irq.c
- add nor flash physmaps
- update defconfig
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove inline from ptep_get_and_clean() to match with header file prototype.
Makes linux-next build.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables I2C on the sh7723-based ap325rxa board.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds platform data for the single I2C channel on sh7366.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds platform data for the single I2C channel on sh7723.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds platform data for two I2C channels to the sh7343.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is based on interrupt acknowledge code for external
interrupt sources on sh3 processors and adds on sh4a processors.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The current kernel behaviour is to reenable interrupts unconditionally
when taking a page fault. This patch changes this to only enable them
if interrupts were previously enabled.
It also fixes a problem seen with this fix in place: the kernel previously
flushed the vsyscall page when handling a signal, which is not only
unncessary, but caused a possible sleep with interrupts disabled.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add implementation of flush_icache_range() suitable for signal handler
and kprobes. Remove flush_cache_sigtramp() and change signal.c to use
flush_icache_range().
Signed-off-by: Chris Smith <chris.smith@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh_pcic_io_xxx function are very old.
In linux-2.4, mrshpc_ss socket driver used this function.
But there is not this driver to the present kernel.
I deleted these cords and checked operation.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The CPU of AP-325RXA is SH7723, but a CPU becomes selectable.
This patch fixes this problem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Enable SH-Ether support and NFS userland support.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support SH-Ether for Hitachi Solution Engine.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains the following cleanups:
- make the following needlessly global code static:
- cf-enabler.c: cf_init()
- cpu/clock.c: __clk_enable()
- cpu/clock.c: __clk_disable()
- process_32.c: default_idle()
- time_32.c: struct clocksource_sh
- timers/timer-tmu.c: struct tmu_timer_ops
- remove the following unused functions (no CONFIG_BLK_DEV_FD on sh):
- process_{32,64}.c: disable_hlt()
- process_{32,64}.c: enable_hlt()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch makes the needlessly global pcibios_max_latency static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch makes the needlessly global EARLY_PCI_OP's static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch makes the needlessly global aica_rtc_{get,set}timeofday()
static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds basic support for the SH7763RDP board.
This supports a basic stuff provided in SH7763, like SCIF,
NOR Flash and USB host.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH7763 has 3 SCIF device. Current code supports SCIF0 and 1.
SCIF0 and 1 are same register constitution, but only SCIF2 is different.
I added support of SCIF2.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This board is SH7723 base board.
This has SCIF, LCDC, USB Host controler, NOR/NAND Flash, Sound,
Ether and other.
This patch supports SCIF, NOR Flash.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
16kB is a useful size on nommu, while 64kB still tends to be too big to
be useful. Newer MMUs are likely to support this as well, so plug it
in in anticipation of those, too.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
PAGE_SIZE doesn't need to be fixed at 4096 on nommu, so stub in a !MMU
case for the various PAGE_SIZE Kconfig options.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently this is only linked in for CONFIG_BINFMT_ELF, make it dependent
on CONFIG_ELF_CORE, so it's both selectable there and also linked in for
CONFIG_BINFMT_ELF_FDPIC.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the following build error:
<-- snip -->
...
MODPOST 1837 modules
ERROR: "board_pci_channels" [drivers/pcmcia/yenta_socket.ko] undefined!
...
make[2]: *** [__modpost] Error 1
<-- snip -->
I freely admit that it's a pathological configuration, but as long as
it is allowed it should build.
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When using single_open(), single_release() should be used instead
of seq_release(), otherwise there is a memory leak.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove arch-specific show_mem() in favor of the generic version.
This also removes the following redundant information display:
- free pages, printed by show_free_areas()
- pages in slab, printed by show_free_areas()
- free swap pages, printed by show_swap_cache_info()
- pages in swapcache, printed by show_swap_cache_info()
where show_mem() calls show_free_areas(), which calls
show_swap_cache_info().
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kmem cache passed to constructor is only needed for constructors that are
themselves multiplexeres. Nobody uses this "feature", nor does anybody uses
passed kmem cache in non-trivial way, so pass only pointer to object.
Non-trivial places are:
arch/powerpc/mm/init_64.c
arch/powerpc/mm/hugetlbpage.c
This is flag day, yes.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Jon Tollefson <kniht@linux.vnet.ibm.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Matt Mackall <mpm@selenic.com>
[akpm@linux-foundation.org: fix arch/powerpc/mm/hugetlbpage.c]
[akpm@linux-foundation.org: fix mm/slab.c]
[akpm@linux-foundation.org: fix ubifs]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch provides an enhancement to kexec/kdump. It implements the
following features:
- Backup/restore memory used by the original kernel before/after
kexec.
- Save/restore CPU state before/after kexec.
The features of this patch can be used as a general method to call program in
physical mode (paging turning off). This can be used to call BIOS code under
Linux.
kexec-tools needs to be patched to support kexec jump. The patches and
the precompiled kexec can be download from the following URL:
source: http://khibernation.sourceforge.net/download/release_v10/kexec-tools/kexec-tools-src_git_kh10.tar.bz2
patches: http://khibernation.sourceforge.net/download/release_v10/kexec-tools/kexec-tools-patches_git_kh10.tar.bz2
binary: http://khibernation.sourceforge.net/download/release_v10/kexec-tools/kexec_git_kh10
Usage example of calling some physical mode code and return:
1. Compile and install patched kernel with following options selected:
CONFIG_X86_32=y
CONFIG_KEXEC=y
CONFIG_PM=y
CONFIG_KEXEC_JUMP=y
2. Build patched kexec-tool or download the pre-built one.
3. Build some physical mode executable named such as "phy_mode"
4. Boot kernel compiled in step 1.
5. Load physical mode executable with /sbin/kexec. The shell command
line can be as follow:
/sbin/kexec --load-preserve-context --args-none phy_mode
6. Call physical mode executable with following shell command line:
/sbin/kexec -e
Implementation point:
To support jumping without reserving memory. One shadow backup page (source
page) is allocated for each page used by kexeced code image (destination
page). When do kexec_load, the image of kexeced code is loaded into source
pages, and before executing, the destination pages and the source pages are
swapped, so the contents of destination pages are backupped. Before jumping
to the kexeced code image and after jumping back to the original kernel, the
destination pages and the source pages are swapped too.
C ABI (calling convention) is used as communication protocol between
kernel and called code.
A flag named KEXEC_PRESERVE_CONTEXT for sys_kexec_load is added to
indicate that the loaded kernel image is used for jumping back.
Now, only the i386 architecture is supported.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Inflate requires some dynamic memory allocation very early in the boot
process and this is provided with a set of four functions:
malloc/free/gzip_mark/gzip_release.
The old inflate code used a mark/release strategy rather than implement
free. This new version instead keeps a count on the number of outstanding
allocations and when it hits zero, it resets the malloc arena.
This allows removing all the mark and release implementations and unifying
all the malloc/free implementations.
The architecture-dependent code must define two addresses:
- free_mem_ptr, the address of the beginning of the area in which
allocations should be made
- free_mem_end_ptr, the address of the end of the area in which
allocations should be made. If set to 0, then no check is made on
the number of allocations, it just grows as much as needed
The architecture-dependent code can also provide an arch_decomp_wdog()
function call. This function will be called several times during the
decompression process, and allow to notify the watchdog that the system is
still running. If an architecture provides such a call, then it must
define ARCH_HAS_DECOMP_WDOG so that the generic inflate code calls
arch_decomp_wdog().
Work initially done by Matt Mackall, updated to a recent version of the
kernel and improved by me.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
nohz: adjust tick_nohz_stop_sched_tick() call of s390 as well
nohz: prevent tick stop outside of the idle loop
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
arch/mips/kernel/stacktrace.c: Heiko can't type
kthread: reduce stack pressure in create_kthread and kthreadd
fix core/stacktrace changes on avr32, mips, sh
This patch introduces the new syscall pipe2 which is like pipe but it also
takes an additional parameter which takes a flag value. This patch implements
the handling of O_CLOEXEC for the flag. I did not add support for the new
syscall for the architectures which have a special sys_pipe implementation. I
think the maintainers of those archs have the chance to go with the unified
implementation but that's up to them.
The implementation introduces do_pipe_flags. I did that instead of changing
all callers of do_pipe because some of the callers are written in assembler.
I would probably screw up changing the assembly code. To avoid breaking code
do_pipe is now a small wrapper around do_pipe_flags. Once all callers are
changed over to do_pipe_flags the old do_pipe function can be removed.
The following test must be adjusted for architectures other than x86 and
x86-64 and in case the syscall numbers changed.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
#include <fcntl.h>
#include <stdio.h>
#include <unistd.h>
#include <sys/syscall.h>
#ifndef __NR_pipe2
# ifdef __x86_64__
# define __NR_pipe2 293
# elif defined __i386__
# define __NR_pipe2 331
# else
# error "need __NR_pipe2"
# endif
#endif
int
main (void)
{
int fd[2];
if (syscall (__NR_pipe2, fd, 0) != 0)
{
puts ("pipe2(0) failed");
return 1;
}
for (int i = 0; i < 2; ++i)
{
int coe = fcntl (fd[i], F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if (coe & FD_CLOEXEC)
{
printf ("pipe2(0) set close-on-exit for fd[%d]\n", i);
return 1;
}
}
close (fd[0]);
close (fd[1]);
if (syscall (__NR_pipe2, fd, O_CLOEXEC) != 0)
{
puts ("pipe2(O_CLOEXEC) failed");
return 1;
}
for (int i = 0; i < 2; ++i)
{
int coe = fcntl (fd[i], F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if ((coe & FD_CLOEXEC) == 0)
{
printf ("pipe2(O_CLOEXEC) does not set close-on-exit for fd[%d]\n", i);
return 1;
}
}
close (fd[0]);
close (fd[1]);
puts ("OK");
return 0;
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Almost all users of this field need a PFN instead of a physical address,
so replace node_boot_start with node_min_pfn.
[Lee.Schermerhorn@hp.com: fix spurious BUG_ON() in mark_bootmem()]
Signed-off-by: Johannes Weiner <hannes@saeureba.de>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Straight forward extensions for huge pages located in the PUD instead of
PMDs.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The goal of this patchset is to support multiple hugetlb page sizes. This
is achieved by introducing a new struct hstate structure, which
encapsulates the important hugetlb state and constants (eg. huge page
size, number of huge pages currently allocated, etc).
The hstate structure is then passed around the code which requires these
fields, they will do the right thing regardless of the exact hstate they
are operating on.
This patch adds the hstate structure, with a single global instance of it
(default_hstate), and does the basic work of converting hugetlb to use the
hstate.
Future patches will add more hstate structures to allow for different
hugetlbfs mounts to have different page sizes.
[akpm@linux-foundation.org: coding-style fixes]
Acked-by: Adam Litke <agl@us.ibm.com>
Acked-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are a lot of places that define either a single bootmem descriptor or an
array of them. Use only one central array with MAX_NUMNODES items instead.
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Flag platforms as HAVE_CLK (or not) in Kconfig, based on whether they
support <linux/clk.h> calls, so that otherwise portable drivers which need
those calls can list that dependency.
Something like this is a prerequisite for merging the musb_hdrc driver,
currently used on platforms including Davinci, OMAP2430, OMAP3xx ... and
the discrete TUSB6010 chip, which doesn't have a natural platform
dependency. (Used with OMAP 2420 in current Nokia N8x0 tablets.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (85 commits)
[ARM] pxa: add base support for PXA930 Handheld Platform (aka SAAR)
[ARM] pxa: add base support for PXA930 Evaluation Board (aka TavorEVB)
[ARM] pxa: add base support for PXA930 (aka Tavor-P)
[ARM] Update mach-types
[ARM] pxa: make littleton to use the new smc91x platform data
[ARM] pxa: make zylonite to use the new smc91x platform data
[ARM] pxa: make mainstone to use the new smc91x platform data
[ARM] pxa: make lubbock to use new smc91x platform data
[NET] smc91x: prepare SMC_USE_PXA_DMA to be specified in platform data
[NET] smc91x: prepare for SMC_IO_SHIFT to be a platform configurable variable
[NET] smc91x: add SMC91X_NOWAIT flag to platform data
[NET] smc91x: favor the use of SMC91X_USE_* instead of SMC_CAN_USE_*
[NET] smc91x: remove "irq_flags" from "struct smc91x_platdata"
[ARM] 5146/1: pxa2xx: convert all boards to call pxa2xx_transceiver_mode helper
Support for LCD on e740 e750 e400 and e800 e-series PDAs
E-series UDC support
PXA UDC - allow use of inverted GPIO for pullup
Add e350 support
Fix broken e-series build
E-series GPIO / IRQ definitions.
...
This allow to dynamically generate attributes and share show/store
functions between attributes. Right now most attributes are generated
by special macros and lots of duplicated code. With the attribute
passed it's instead possible to attach some data to the attribute
and then use that in shared low level functions to do different things.
I need this for the dynamically generated bank attributes in the x86
machine check code, but it'll allow some further cleanups.
I converted all users in tree to the new show/store prototype. It's a single
huge patch to avoid unbisectable sections.
Runtime tested: x86-32, x86-64
Compiled only: ia64, powerpc
Not compile tested/only grep converted: sh, arm, avr32
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jack Ren and Eric Miao tracked down the following long standing
problem in the NOHZ code:
scheduler switch to idle task
enable interrupts
Window starts here
----> interrupt happens (does not set NEED_RESCHED)
irq_exit() stops the tick
----> interrupt happens (does set NEED_RESCHED)
return from schedule()
cpu_idle(): preempt_disable();
Window ends here
The interrupts can happen at any point inside the race window. The
first interrupt stops the tick, the second one causes the scheduler to
rerun and switch away from idle again and we end up with the tick
disabled.
The fact that it needs two interrupts where the first one does not set
NEED_RESCHED and the second one does made the bug obscure and extremly
hard to reproduce and analyse. Kudos to Jack and Eric.
Solution: Limit the NOHZ functionality to the idle loop to make sure
that we can not run into such a situation ever again.
cpu_idle()
{
preempt_disable();
while(1) {
tick_nohz_stop_sched_tick(1); <- tell NOHZ code that we
are in the idle loop
while (!need_resched())
halt();
tick_nohz_restart_sched_tick(); <- disables NOHZ mode
preempt_enable_no_resched();
schedule();
preempt_disable();
}
}
In hindsight we should have done this forever, but ...
/me grabs a large brown paperbag.
Debugged-by: Jack Ren <jack.ren@marvell.com>,
Debugged-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fixes this type of problem:
CC arch/s390/kernel/stacktrace.o
arch/s390/kernel/stacktrace.c:84: warning: data definition has no type or storage class
arch/s390/kernel/stacktrace.c:84: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/s390/kernel/stacktrace.c:84: warning: parameter names (without types) in function declaration
arch/s390/kernel/stacktrace.c:97: warning: data definition has no type or storage class
arch/s390/kernel/stacktrace.c:97: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/s390/kernel/stacktrace.c:97: warning: parameter names (without types) in function declaration
caused by "stacktrace: export save_stack_trace[_tsk]"
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (72 commits)
Revert "x86/PCI: ACPI based PCI gap calculation"
PCI: remove unnecessary volatile in PCIe hotplug struct controller
x86/PCI: ACPI based PCI gap calculation
PCI: include linux/pm_wakeup.h for device_set_wakeup_capable
PCI PM: Fix pci_prepare_to_sleep
x86/PCI: Fix PCI config space for domains > 0
Fix acpi_pm_device_sleep_wake() by providing a stub for CONFIG_PM_SLEEP=n
PCI: Simplify PCI device PM code
PCI PM: Introduce pci_prepare_to_sleep and pci_back_from_sleep
PCI ACPI: Rework PCI handling of wake-up
ACPI: Introduce new device wakeup flag 'prepared'
ACPI: Introduce acpi_device_sleep_wake function
PCI: rework pci_set_power_state function to call platform first
PCI: Introduce platform_pci_power_manageable function
ACPI: Introduce acpi_bus_power_manageable function
PCI: make pci_name use dev_name
PCI: handle pci_name() being const
PCI: add stub for pci_set_consistent_dma_mask()
PCI: remove unused arch pcibios_update_resource() functions
PCI: fix pci_setup_device()'s sprinting into a const buffer
...
Fixed up conflicts in various files (arch/x86/kernel/setup_64.c,
arch/x86/pci/irq.c, arch/x86/pci/pci.h, drivers/acpi/sleep/main.c,
drivers/pci/pci.c, drivers/pci/pci.h, include/acpi/acpi_bus.h) from x86
and ACPI updates manually.
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (241 commits)
[ARM] 5171/1: ep93xx: fix compilation of modules using clocks
[ARM] 5133/2: at91sam9g20 defconfig file
[ARM] 5130/4: Support for the at91sam9g20
[ARM] 5160/1: IOP3XX: gpio/gpiolib support
[ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.
[ARM] 5084/1: zylonite: Register AC97 device
[ARM] 5085/2: PXA: Move AC97 over to the new central device declaration model
[ARM] 5120/1: pxa: correct platform driver names for PXA25x and PXA27x UDC drivers
[ARM] 5147/1: pxaficp_ir: drop pxa_gpio_mode calls, as pin setting
[ARM] 5145/1: PXA2xx: provide api to control IrDA pins state
[ARM] 5144/1: pxaficp_ir: cleanup includes
[ARM] pxa: remove pxa_set_cken()
[ARM] pxa: allow clk aliases
[ARM] Feroceon: don't disable BPU on boot
[ARM] Orion: LED support for HP mv2120
[ARM] Orion: add RD88F5181L-FXO support
[ARM] Orion: add RD88F5181L-GE support
[ARM] Orion: add Netgear WNR854T support
[ARM] s3c2410_defconfig: update for current build
[ARM] Acer n30: Minor style and indentation fixes.
...
IRQ trigger type can be specified in the IRQ resource definition by
IORESOURCE_IRQ_*, we need only one way to specify this.
This also fixes the following small issue:
To allow dynamic support for multiple platforms, when those relevant
macros are not defined for one specific platform, the default case
will be:
- SMC_DYNAMIC_BUS_CONFIG defined
- and SMC_IRQ_FLAGS = IRQF_TRIGGER_RISING
While if "irq_flags" is missing when defining the smc91x_platdata,
usually as follows:
static struct smc91x_platdata xxxx_smc91x_data = {
.flags = SMC91X_USE_XXBIT,
};
The lp->cfg.irq_flags will always be overriden by the above structure
(due to a memcpy), thus rendering lp->cfg.irq_flags to be "0" always.
(regardless of the default SMC_IRQ_FLAGS or IORESOURCE_IRQ_* flags)
Fixes this by forcing to use IORESOURCE_IRQ_* flags if present, and
make the only user of smc91x_platdata.irq_flags (renesas/migor) to
use IORESOURCE_IRQ_*.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Andrew Morton reported this against linux-next:
ERROR: ".save_stack_trace" [tests/backtracetest.ko] undefined!
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Russell King did the following back in 2003:
<-- snip -->
[PCI] pci-9: Kill per-architecture pcibios_update_resource()
Kill pcibios_update_resource(), replacing it with pci_update_resource().
pci_update_resource() uses pcibios_resource_to_bus() to convert a
resource to a device BAR - the transformation should be exactly the
same as the transformation used for the PCI bridges.
pci_update_resource "knows" about 64-bit BARs, but doesn't attempt to
set the high 32-bits to anything non-zero - currently no architecture
attempts to do something different. If anyone cares, please fix; I'm
going to reflect current behaviour for the time being.
Ivan pointed out the following architectures need to examine their
pcibios_update_resource() implementation - they should make sure that
this new implementation does the right thing. #warning's have been
added where appropriate.
ia64
mips
mips64
This cset also includes a fix for the problem reported by AKPM where
64-bit arch compilers complain about the resource mask being placed
in a u32.
<-- snip -->
This patch removes the unused pcibios_update_resource() functions the
kernel gained since, from FRV, m68k, mips & sh architectures.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
It's not even passed on to smp_call_function() anymore, since that
was removed. So kill it.
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
It's never used and the comments refer to nonatomic and retry
interchangably. So get rid of it.
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This converts sh to use the new helpers for smp_call_function() and
friends, and adds support for smp_call_function_single(). Not tested,
but it compiles.
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Presently the --fdpic specifier and the --isa matching clash when
building with FDPIC toolchains. As we have no interest in building the
kernel with --fdpic in the first place, always try to add in -mno-fdpic
to the default flags.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH7763's setup code use old DECLARE_INTC_DESC.
There was a compile error because of this.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
RSK7203 is supportable through the generic machvec, so we add a defconfig
for those bits. This gets updated with more complete board support later.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
4k stacks on nommu ends up blowing up with all sorts of interesting
slab corruption. Disable this by default unless BROKEN is also
enabled.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the following build error caused by
commit a1dc4b59fa
(sh: intc_sh5 depends on cayman board for IRQ priority table.):
<-- snip -->
...
CC arch/sh/kernel/cpu/irq/intc-sh5.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/kernel/cpu/irq/intc-sh5.c: In function 'plat_irq_setup':
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/kernel/cpu/irq/intc-sh5.c:257: error: expected declaration or statement at end of input
make[4]: *** [arch/sh/kernel/cpu/irq/intc-sh5.o] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
