This patch adds TMU platform data for sh7785. Both clockevent
and clocksource support is enabled.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Make sure that clk->ops->init() only gets called once in
the case of CLK_ALWAYS_ENABLED. Without this patch the
init() callback may be called multiple times.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently this is special-cased for early initialization. While there are
situations where these static early initializations are still necessary,
with minor changes it is possible to use this for the regular ioremap
implementation as well. This allows us to kill off the special-casing for
the remap completely and to start tidying up all of the SH-5
special-casing in drivers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The old arch/sh/kernel/timers/ directly will be going away completely
once the rest of the TMU users are migrated, so move the dummy broadcast
driver up a level in preparation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the stragglers (MTU2/CMT/etc.) have been rewritten and we are
selecting both GENERIC_TIME and GENERIC_CLOCKEVENTS, the get_offset()
timer op is completely unused. As a result, we are now able to kill off
the ARCH_USES_GETTIMEOFFSET references.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All of the SH timers use a roughly identical structure for platform data,
which presently is broken out for each block. Consolidate all of these
definitions, as there is no reason for them to be broken out in the first
place.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds TMU platform data for sh7722. Only clockevent
mode is enabled for now, clocksource requires this patch:
"clocksource: setup mult_orig in clocksource_enable()"
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes the old MTU2 driver (CONFIG_SH_MTU2/timer-mtu2.c)
As replacement, select the sh_cmt driver with CONFIG_SH_TIMER_MTU2
and configure timer channel using platform data.
If multiple MTU channels are enabled using platform data, use the
earlytimer parameter on the kernel command line to select channel.
For instance, use "earlytimer=sh_mtu2.0" to select the first channel.
To verify which timer is being used, look at printouts or the timer
irq count in /proc/interrupts.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds MTU2 platform data for the following cpus:
- sh7201 (3/5 channels)
- sh7203/sh7263 (2/4 channels)
- sh7206 (3/5 channels)
- MXG (3/5 channels)
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert sh to use GENERIC_TIME via the arch_getoffset() infrastructure.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Impact: cleanup
Convert the last remaining users to struct irq_chip and remove the
define.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Impact: cleanup
convert the last remaining users to no_irq_chip
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes the old CMT driver (CONFIG_SH_CMT/timer-cmt.c)
As replacement, select the sh_cmt driver with CONFIG_SH_TIMER_CMT
and configure timer channel using platform data.
If multiple CMT channels are enabled using platform data, use the
earlytimer parameter on the kernel command line to select channel.
For instance, use "earlytimer=sh_cmt.0" to select the first channel.
To verify which timer is being used, look at printouts or the timer
irq count in /proc/interrupts.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds 16-bit cmt platform data for the following cpus:
- sh7619 (2 channels)
- sh7203/sh7263 (2 channels)
- sh7206 (2 channels)
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The device registration was accidentally omitted, add it back in. Do some
basic device probing as well, so this doesn't show up for platforms that
tie in to the RTC interface properly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch moves the SuperH timer setup code from time_init()
to late_time_init(). Good things about this change:
- interrupts: they are enabled at late_time_init()
- mm: regular kmalloc() can be used at late_time_init()
Together with moving to late_time_init() this patch changes
the sh_cmt driver to always allocate with kmalloc(). This
simplifies the code a bit and also fixes section mismatches.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The sh architecture has some code in the .text.init section, but it
does not reference that section in its linker scripts.
This change moves this code from the .text.init section to the
.init.text section, which is presumably where it belongs.
Signed-off-by: Tim Abbott <tabbott@mit.edu>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This has the consequence of changing the section name use for head
code from ".text.head" to ".head.text". Since this commit changes all
users in the architecture, this change should be harmless.
Signed-off-by: Tim Abbott <tabbott@mit.edu>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mmap2 uses a fixed page shift of 12, regardless of the PAGE_SIZE setting.
Fix up the mmap2 code to add some sanity checks on the mapping, and to
update pgoff accordingly.
Error handling bits based on 4280e3126f
("frv: fix mmap2 error handling").
Signed-off-by: Toshinobu Sugioka <sugioka@itonet.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This consolidates the pci_iomap() definitions and reworks how the I/O
port base is handled. PCI channels can register their own I/O map base,
or if none is provided, the system-wide generic I/O base is used instead.
Functionally nothing changes, while this allows us to kill off lots of
I/O address special casing and lookups.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use plat_early_device_setup() to register Early Platform Data
for SuperH Mobile processors.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a plat_early_device_setup() function to allow
processor-specific code to register Early Platform Data.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Extend the 32-bit SuperH timer code to register and probe
the earlytimer class of Early Platform Drivers.
This registers the sh_cmt driver if compiled-in.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Adds a __get_pci_io_base() function which is used to match a port range
against struct pci_channel. This allows us to detect if a port range is
assigned to pci or happens to be legacy port io. While at it, remove unused
cpu-specific cruft.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds uio_pdrv_genirq support for the VEU.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds uio_pdrv_genirq support for the VPU.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the SH-Mobile I2C controller on the SH7724.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements initial support for the SH-Mobile R2R CPU.
Based on Rev 0.11 of the initial SH7724 hardware manual.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This corrects a race with the PHY RST bit not being set properly if the
PLL status changes right before timeout. This resulted in it potentially
failing even if the device came up in time.
Special thanks to Mr. Juha Leppanen and Iwamatsu-san for reporting this
out and reviewing it.
Reported-by: Juha Leppanen <juha_motorsportcom@luukku.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Tested-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (23 commits)
sh: sh7785lcr: Map whole PCI address space.
sh: Fix up DSP context save/restore.
sh: Fix up number of on-chip DMA channels on SH7091.
sh: update defconfigs.
sh: Kill off broken direct-mapped cache mode.
sh: Wire up ARCH_HAS_DEFAULT_IDLE for cpuidle.
sh: Add a command line option for disabling I/O trapping.
sh: Select ARCH_HIBERNATION_POSSIBLE.
sh: migor: Fix up CEU use flags.
input: migor_ts: add wakeup support
rtc: rtc-sh: use set_irq_wake()
input: sh_keysc: use enable/disable_irq_wake()
sh: intc: set_irq_wake() support
sh: intc: install enable, disable and shutdown callbacks
clocksource: sh_cmt: use remove_irq() and remove clockevent workaround
sh: ap325 and Migo-R use new sh_mobile_ceu_info flags
sh: Fix up -Wformat-security whining.
sh: ap325rxa: Add ov772x support, again.
sh: Sanitize asm/mmu.h for assembly use.
sh: Tidy up sh7786 pinmux table.
...
There were a number of issues with the DSP context save/restore code,
mostly left-over relics from when it was introduced on SH3-DSP with
little follow-up testing, resulting in things like task_pt_dspregs()
referencing incorrect state on the stack.
This follows the MIPS convention of tracking the DSP state in the
thread_struct and handling the state save/restore in switch_to() and
finish_arch_switch() respectively. The regset interface is also updated,
which allows us to finally be rid of task_pt_dspregs() and the special
cased task_pt_regs().
Signed-off-by: Michael Trimarchi <michael@evidence.eu.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Forcing direct-mapped worked on certain older 2-way set associative
parts, but was always error prone on 4-way parts. As these are the
norm these days, there is not much point in continuing to support this
mode. Most of the folks that used direct-mapped mode generally just
wanted writethrough caching in the first place..
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
cpuidle wants ARCH_HAS_DEFAULT_IDLE defined in order to use the
default idle loop. So, make it accessible and enable it for all
sh machines.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds a 'noiotrap' kernel command line option to permit disabling of
I/O trapping. This is mostly useful for running on emulators where the
physical device limitations are not an issue.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
