Commit Graph

61 Commits

Author SHA1 Message Date
Kristen Carlson Accardi
ca77329fb7 [libata] Link power management infrastructure
Device Initiated Power Management, which is defined
in SATA 2.5 can be enabled for disks which support it.
This patch enables DIPM when the user sets the link
power management policy to "min_power".

Additionally, libata drivers can define a function
(enable_pm) that will perform hardware specific actions to
enable whatever power management policy the user set up
for Host Initiated Power management (HIPM).
This power management policy will be activated after all
disks have been enumerated and intialized.  Drivers should
also define disable_pm, which will turn off link power
management, but not change link power management policy.

Documentation/scsi/link_power_management_policy.txt has additional
information.

Signed-off-by:  Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-29 11:00:35 -04:00
Tejun Heo
054a5fbace libata: track SLEEP state and issue SRST to wake it up
ATA devices in SLEEP mode don't respond to any commands.  SRST is
necessary to wake it up.  Till now, when a command is issued to a
device in SLEEP mode, the command times out, which makes EH reset the
device and retry the command after that, causing a long delay.

This patch makes libata track SLEEP state and issue SRST automatically
if a command is about to be issued to a device in SLEEP.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Bruce Allen <ballen@gravity.phys.uwm.edu>
Cc: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-29 06:15:25 -04:00
Jeff Garzik
2dcb407e61 [libata] checkpatch-inspired cleanups
Tackle the relatively sane complaints of checkpatch --file.

The vast majority is indentation and whitespace changes, the rest are

* #include fixes
* printk KERN_xxx prefix addition
* BSS/initializer cleanups

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-23 20:59:42 -04:00
Robert Hancock
1333e19434 libata: add human-readable error value decoding
This adds human-readable decoding of the ATA status and error registers
(similar to what drivers/ide does) as well as the SATA Serror register
to libata error handling output.  This prevents the need to pore
through standards documents to figure out the meaning of the bits
in these registers when looking at error reports.  Some bits that
drivers/ide decoded are not decoded here, since the bits are either
command-dependent or obsolete, and properly parsing them would add
too much complexity.

Signed-off-by: Robert Hancock <hancockr@shaw.ca>

[edited slightly to make output a bit more symmetric]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:45 -04:00
Tejun Heo
854c73a2f1 libata: misc updates for AN
Update AN support in preparation of PMP support.

* s/ata_id_has_AN/ata_id_has_atapi_AN/
* add AN enabled reporting during configuration
* add err_mask to AN configuration failure reporting
* update LOCKING comment for ata_scsi_media_change_notify()
* check whether ATA dev is attached to SCSI dev ata_scsi_media_change_notify()
* set ATA_FLAG_AN in ahci and sata_sil24

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Kriten Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:40 -04:00
Alan Cox
c7293870a9 libata: Strict checking for identify reporting
The ATA specifications require checks on certain flags before assuming
the validity of other data. Go through the methods and correct those
needing extra checks. Also note limits on ata_id_major_version with
respect to ATA-1 and ATA-2. Correct the 32bit PIO check.

Wants to sit in -mm for a bit in case of a screwup on my part that I
didn't hit on the test drives and also in case someone, somewhere has
a drive that gets it wrong.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:37 -04:00
Kristen Carlson Accardi
9f45cbd3f0 [libata] check for SATA async notify support
Check to see if an ATAPI device supports Asynchronous Notification.
If so, enable it, if the host controller supports AN.

Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:33 -04:00
Alan Cox
0bc2a79a20 libata: Correct IORDY handling
Debugging a report of a problem with an ancient solid state disk showed
up some problems in the IORDY handling

1.	We check the wrong bit to see if the device has IORDY
2.	Even then some ancient creaking piles of crap don't support
	SETXFER at all.

The cases it fixes are obscure and the risk of side effects is slight
but possible. This also moves us slightly closer to supporting original
MFM/RLL disks with libata.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:32 -04:00
Bartlomiej Zolnierkiewicz
91a6d4ed33 ata: add ATA_MWDMA* and ATA_SWDMA* defines
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-31 04:00:19 -04:00
Bartlomiej Zolnierkiewicz
4099d14322 ide: add PIO masks
* Add ATA_PIO[0-6] defines to <linux/ata.h>.

* Add ->pio_mask field to ide_pci_device_t and ide_hwif_t.

* Add PIO masks to host drivers.

<linux/ata.h> change ACK-ed by Jeff Garzik <jeff@garzik.org>.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-20 01:11:59 +02:00
Tejun Heo
814600ee10 libata-link: add PMP related ATA constants
Add Port Multiplier related ATA constants and macros.  Some of these
will be used by ata_link implementation.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-10 21:46:03 -04:00
Jeff Garzik
ab2181cf39 [ATA] Add named constant for ATAPI command DEVICE RESET
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-09 12:17:33 -04:00
Albert Lee
2c3d2a46f1 libata passthru: update cached device paramters
INIT_DEV_PARAMS and SET_MULTI_MODE change the device parameters cached
by libata.  Re-read IDENTIFY DEVICE info and update the cached device
paramters when seeing these commands.

Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-06-09 23:08:12 -04:00
Albert Lee
1dce589c38 libata passthru: support PIO multi commands
support the pass through of PIO multi commands.

Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-06-09 23:08:11 -04:00
Mark Lord
169439c2e3 libata: Handle drives that require a spin-up command before first access
(S)ATA drives can be configured for "power-up in standby",
a mode whereby a specific "spin up now!" command is required
before the first media access.

Currently, a drive with this feature enabled can not be used at all
with libata, and once in this mode, the drive becomes a doorstop.

The older drivers/ide subsystem at least enumerates the drive,
so that it can be woken up after the fact from a userspace HDIO_*
command, but not libata.

This patch adds support to libata for the "power-up in standby"
mode where a "spin up now!" command (SET_FEATURES) is needed.
With this, libata will recognize such drives, spin them up,
and then re-IDENTIFY them if necessary to get a full/complete
set of drive features data.

Drives in this state are determined by looking for
special values in id[2], as documented in the current ATA specs.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28 14:40:40 -04:00
Alan Cox
1e999736ca libata: HPA support
Signed-off-by: Alan Cox <alan@redhat.com>

Add support for ignoring the BIOS HPA result (off by default) and setting
the disk to the full available size unless already frozen.

Tested with various platforms/disks and confirmed to work with the
Macintosh (which broke earlier) and ata_piix (breakage due to the LBA48
readback that Tejun fixed).

For normal users this brings us, I believe, to feature parity with old IDE
(and of course more featured in some areas too).
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28 14:16:06 -04:00
Mark Lord
5a5dbd18a7 libata: add support for READ/WRITE LONG
The READ/WRITE LONG commands are theoretically obsolete,
but the majority of drives in existance still implement them.

The WRITE_LONG and WRITE_LONG_ONCE commands are of particular
interest for fault injection testing -- eg. creating "media errors"
at specific locations on a disk.

The fussy bit is that these commands require a non-standard
sector size, usually 520 bytes instead of 512.

This patch adds support to libata for READ/WRITE LONG commands
issued via SG_IO/ATA_16.

Signed-off-by:  Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28 14:16:01 -04:00
Albert Lee
18d6e9d518 libata: Limit max sector to 128 for TORiSAN DVD drives (take 3)
patch 3/4:
  The TORiSAN drive locks up when max sector == 256.
  Limit max sector to 128 for the TORiSAN DRD-N216 drives.
  (http://bugzilla.kernel.org/show_bug.cgi?id=6710)

Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-04 02:12:27 -04:00
Tejun Heo
32d9091156 libata: test major version in ata_id_is_sata()
Test major version in ata_id_is_sata() not separately.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-23 05:37:11 -05:00
Tejun Heo
61f216c719 libata: fix drive side 80c cable check, take 3
The 80c wire bit is bit 13, not 14.  Bit 14 is always 1 if word93 is
implemented.  This increases the chance of incorrect wire detection
especially because host side cable detection is often unreliable and
we sometimes soley depend on drive side cable detection.  Fix the test
and add word93 validity check.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-15 18:04:01 -05:00
Alan
49554c1956 ata: Add defines for the iordy bits
IORDY and IORDY enable/disable flags.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09 17:39:39 -05:00
Tejun Heo
a0cf733b33 libata: straighten out ATA_ID_* constants
* Kill _OFS suffixes in ATA_ID_{SERNO|FW_REV|PROD}_OFS for consistency
  with other ATA_ID_* constants.

* Kill ATA_SERNO_LEN

* Add and use ATA_ID_SERNO_LEN, ATA_ID_FW_REV_LEN and ATA_ID_PROD_LEN.
  This change also makes ata_device_blacklisted() use proper length
  for fwrev.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09 17:39:30 -05:00
Alan Cox
fc085150b4 [PATCH] libata: add 40pin "short" cable support, honour drive side speed detection
[deweerdt@free.fr: build fix]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Frederik Deweerdt <deweerdt@free.fr>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-01 22:40:25 -05:00
Jeff Garzik
9bec2e3852 [libata] Trim trailing whitespace. 2006-08-31 00:02:15 -04:00
Alan Cox
b352e57dc3 [PATCH] libata: Add CompactFlash support
The CFA world has some additional rules and drive modes we need to support for
newer expansion cards and on embedded boxes

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-08-14 14:04:37 -04:00
Jeff Garzik
8b881b0410 [ATA] Increase lba48 max-sectors from 200 to 256.
Also, moved ATA_MAX_SECTORS and ATA_MAX_SECTORS_LBA48 from
linux/libata.h to linux/ata.h, now that they truly reflect the standard
(well... mostly; note TODO comment).

This changes the performance profile (and potential bug profile)
for a bunch of drivers, so be wary.
2006-08-10 06:49:45 -04:00
zhao, forrest
3057ac3c1a [PATCH] Snoop SET FEATURES - WRITE CACHE ENABLE/DISABLE command(v5)
This patch makes libata snoop 'SET FEATURES - WRITE CACHE
ENABLE/DISABLE' command, executing requisite revalidation processes
to update cached data.

Signed-off-by: Forrest Zhao <forrest.zhao@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-06-12 00:18:35 -04:00
Tejun Heo
88e490340e [PATCH] libata-ncq: add NCQ related ATA/libata constants and macros
Add NCQ related ATA/libata constants and macros.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-05-15 21:03:38 +09:00
Tejun Heo
12436c30f4 Merge branch 'irq-pio'
Conflicts:

	drivers/scsi/libata-core.c
	include/linux/libata.h
2006-05-15 20:59:15 +09:00
Tejun Heo
9be1e979f2 [PATCH] libata-eh: add ATA and libata flags for new EH
Add ATA and libata flags to be used by new EH.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-05-15 20:58:17 +09:00
Jeff Garzik
11ed56fb78 Merge branch 'upstream'
Conflicts:

	drivers/scsi/sata_vsc.c
2006-03-24 09:24:04 -05:00
Alan Cox
b6782728d7 [PATCH] libata: Add the useful macros/constants needed for merging PATA stuff
HPA presence/enabled
HPA commands

Also add ata_id_is_cfa() as that is needed to detect and handle CF cards
which currently we reject.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-03-21 21:21:31 -05:00
Albert Lee
f59b0cf8a3 [PATCH] libata-dev: Remove ATA_PROT_PIO_MULT
Remove the ATA_PROT_PIO_MULT protocol.

Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-03-21 20:39:46 -05:00
Albert Lee
c2956a3b0d [PATCH] libata-dev: recognize WRITE_MULTI_FUA_EXT for r/w multiple
Recognize ATA_CMD_WRITE_MULTI_FUA_EXT as r/w multiple commands.

Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-03-03 12:19:43 -05:00
Jeff Garzik
3875e1945b Merge branch 'upstream' 2006-02-13 00:13:48 -05:00
Tejun Heo
3d2ca91095 [PATCH] libata: separate out ata_id_major_version()
Separate out ATA major version calculation from ata_dev_identify()
into ata_id_major_version().  It's preparation for splitting
ata_dev_identify().

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2006-02-12 14:24:41 -05:00
Jeff Garzik
8dd2e3bd57 Merge branch 'tmp' 2006-01-27 02:26:46 -05:00
Jeff Garzik
ea9b395fe2 Merge branch 'upstream' 2006-01-17 10:29:06 -05:00
Jeff Garzik
0825788ff2 Merge branch 'upstream' 2006-01-17 10:26:28 -05:00
Linus Torvalds
d99cf9d679 Merge branch 'post-2.6.15' of git://brick.kernel.dk/data/git/linux-2.6-block
Manual fixup for merge with Jens' "Suspend support for libata", commit
ID 9b84754866.

Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 09:01:25 -08:00
Jens Axboe
9b84754866 [PATCH] Suspend support for libata
This patch adds suspend patch to libata, and ata_piix in particular. For
most low level drivers, they should just need to add the 4 hooks to
work. As I can only test ata_piix, I didn't enable it for more
though.

Suspend support is the single most important feature on a notebook, and
most new notebooks have sata drives. It's quite embarrassing that we
_still_ do not support this. Right now, it's perfectly possible to
suspend the drive in mid-transfer.

Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:36:09 -08:00
Tejun Heo
9a3dccc425 [BLOCK] add FUA support to libata
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
2006-01-06 09:56:18 +01:00
Albert Lee
07f6f7d074 [PATCH] libata irq-pio: add read/write multiple support
- add is_multi_taskfile() to ata.h
   - initialize ata_device->multi_count with device identify data
   - use ata_pio_sectors() to support r/w multiple commands

Signed-off-by: Albert Lee <albertcc@tw.ibm.com>

========
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-11-09 01:22:19 -05:00
Jeff Garzik
35ebbae283 Merge branch 'master' 2005-10-28 12:30:29 -04:00
Jeff Garzik
15dbb5a3f9 Merge branch 'master' 2005-10-28 12:30:16 -04:00
Jeff Garzik
057ace5e79 libata: const-ification bombing run
Enforce access rules where appropriate.

If the compiler is smart enough, this may buy us an optimization or two
as a side effect.
2005-10-22 14:27:05 -04:00
Alan Cox
11e29e2151 libata: handle early device PIO modes correctly 2005-10-21 18:46:32 -04:00
Jeff Garzik
4e0e329d9a Merge branch 'upstream' 2005-10-18 21:23:11 -04:00
Albert Lee
c6a33e2464 [PATCH] libata CHS: LBA28/LBA48 optimization (revise #6)
- add lba_28_ok() and lba_48_ok() to ata.h.
     - check ending block number instead of staring block number.
     - use lba_28_ok() for CHS range check
     - LBA28/LBA48 optimization

Suggested by Mark Lord and Alan Cox.

Signed-off-by: Albert Lee <albertcc@tw.ibm.com>

=====
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-10-18 17:18:16 -04:00
Albert Lee
8cbd6df1f0 [PATCH] libata CHS: calculate read/write commands and protocol on the fly (revise #6)
- merge ata_prot_to_cmd() and ata_dev_set_protocol() as
       ata_rwcmd_protocol()
     - pave road for read/write multiple support
     - remove usage of pre-cached command and protocol values and call
       ata_rwcmd_protocol() instead

Signed-off-by: Albert Lee <albertcc@tw.ibm.com>

==============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-10-18 17:16:13 -04:00