Use of time_before() macro, defined at linux/jiffies.h, which deal with
wrapping correctly and are nicer to read.
Signed-off-by: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Ben Collins <bcollins@debian.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix debug code so it prints the correct speed (was defaulting to 100, so
anything > 400 showed only 100).
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@debian.org>
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Skip a superfluous pause that occured when the config ROM of a node was
scanned unsuccessfully. This also occurs if a node without link wrongly
enables its "link active" self ID flag. A GWCTech 6-port hub does this.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Cc: Ben Collins <bcollins@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Units were not detected if the local IRM performed a bus reset. ("The root
node is not cycle master capable; selecting a new root node and resetting...",
often seen with iPods and other SBP-2 devices). Rearrange the order of IRM
duties and node scanning. TODO: Audit the ROM caching and parsing code for
underlying issues.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Cc: Ben Collins <bcollins@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Set serialize_io=1 by default. This is safer and required by seemingly more
and more hardware. It causes little or no performance loss for S400 devices.
Performance of S800 1394b devices may drop by 25...30%. Therefore make the
parameter's description and dmesg message clearer about performance impact.
Update description of the max_speed parameter too. IEEE1394_SPEED_MAX is
currently S800.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Cc: Ben Collins <bcollins@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixes for deadlocks of the ieee1394 and scsi subsystems and long delays in
futile error recovery attempts when SBP-2 devices are removed or drivers are
unloaded.
- Complete commands quickly with DID_NO_CONNECT if the 1394 node is gone or if
the 1394 low-level driver was unloaded.
- Skip unnecessary work in the eh_abort_handler and eh_device_reset_handler if
the node or 1394 low-level driver is gone.
- Let scsi's high-level shut down gracefully when sbp2 is being unloaded or
detached from the 1394 unit. A call to scsi_remove_device is added for this
purpose, which requires us to store a scsi_device pointer.
- scsi_device pointer is obtained from slave_alloc hook and cleared by
slave_destroy. This avoids usage of the pointer after the scsi device was
deleted e.g. by the user via scsi_mod's sysfs interface.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Cc: Ben Collins <bcollins@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This change removes a bogus error message from the IOC4 serial driver
interrupt handler.
This error message is bogus for two reasons. First, it can never occur
given that current code takes care to initialize IOC4 in such a way that
these "unknown" interrupts could never occur. Second, this code fails to
take into account that other drivers can share the IOC4 interrupt mechanism
through SA_SHIRQ, and thus this driver is not in-fact "all-knowing".
Finally, this error message triggers every time some "unknown" interrupt
occurs -- it's not rate limited or repetition limited in any way, thereby
effectively denying use of the console device. Given its bogosity in the
first place, it's best to just get rid of it entirely.
Acked-by: Pat Gefre <pfg@sgi.com>
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
GPIO fix for the composite and tv mute states of bt8xx card #135: DViCO
FusionHDTV5 Lite. Without this patch, selecting one of these states could
produce unexpected behavior.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
the free_irq() in USB suspend breaks resume on some setups where USB
(ohci/ehci) shares the interrupt with an other device.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The driver does a readl() on DEVICE_ID which is 2-byte aligned and
2-bytes in size. It's doing this read just to flush write buffers.
Create IN16() and OUT16() macros, and use the former to do this I/O
load.
Signed-off-by: David S. Miller <davem@davemloft.net>
The SMU driver has a small mistake in the locking of the interrupt code,
if polled access and interrupt access race, interrupt may take a lock
and return without releasing it. This fixes it. With that patch, the
driver is rock solid with my experimental thermal control (which bangs
it pretty hard) racing with real time clock and cpufreq handling.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The function s3c2410fb_activate_var does not return
a value, therefore it should be declared void.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Workaround for the ioremap patch that produces a blank display on some
chipsets
- Make hwcursor = 0 the default. The hardware cursor does not work with all
hardware.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- use nonseekable_open() instead of messing with
if (*ppos != file->f_pos)
return -EISPIPE
in ->write() (->read is NULL).
- trivial __user annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- print pointers with %p
- casting pointer structure field to int and printing it with %d...
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A bunch of create_proc_dir_entry() calls creating directories had crept
in since the last sweep; converted to proc_mkdir().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's pointless to include mach-types.h if you're not going to use
anything from it. These references were removed as a result of:
grep -lr 'asm/mach-types\.h' . | xargs grep -L 'machine_is_\|MACH_TYPE_\|MACHINE_START\|machine_type'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since asm/hardware.h's only reason for existing is to include
asm/arch/hardware.h, it's completely pointless to include both.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix warning:
drivers/video/pxafb.h:119:5: warning: "DEBUG" is not defined
by removing the whole
#if DEBUG
#define DPRINTK(fmt, args...) printk...etc...
#else
#define DPRINTK(fmt, args...)
#endif
stuff - we have pr_debug() for this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Only start up nonstatic sockets if both IO and MEM resources are available.
Thanks to Russell King and Matthew Wilcox for tracking this down.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
When creating a multipath device, if the queue_if_no_path parameter is
specified it gets ignored.
While the queue_if_no_path variable is correctly set to 1, the
saved_queue_if_no_path gets set to 0. When the device is subsequently made
live (resumed), the saved value (0) always overwrites the live value (1) so
the option *always* gets turned off.
The fix adds a parameter to the queue_if_no_path() function to indicate
whether the previous value should be preserved or not - if not, as when the
device is being set up, the saved value is set to the new value (1).
Signed-Off-By: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If anything is waiting on a device's table when the device is removed, we
must first wake it up so it will release its reference. Otherwise the
table's reference count will not drop to zero and the table will not get
removed.
Signed-Off-By: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Latest wireless extensions moved a field from netdev -> wireless_handlers.
The WE core will now printk a warning on every call to get_wireless_stats()
on a driver that still uses the old field. This patch fixes orinoco.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Put the IPMI poweroff_powercycle parameter into sysfs. This field is
dynamically settable and is valuable to have in sysfs.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ralph Metzler wrote:
> AFAIR, there is a bug in tda10021.c in tda10021_readreg() which
> references state->frontend.dvb->num
> This is fatal if the frontend is not at the probed address and thus
> not yet registered (no dvb entry set yet -> NULL pointer ...).
The attached patch should get rid of the oops.
Signed-off-by: Jon Burgess <jburgess@uklinux.net>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Written by Adrian Sun (asun@darksunrising.com).
Ported to 2.6.x by Tom 'spot' Callaway <tcallawa@redhat.com>.
Further cleaned up and integrated by David S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>
The IB spec defines the field to be 32 bits, not 16 bits.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix interrupt test handler by adding check for IRQ assertion in
PCI_STATE register in addition to the status block updated bit.
Add test for valid ethernet address in tg3_set_mac_addr().
Add tg3_bus_string() to setup the PCI bus speed/width string for all
PCI/PCIX/PCI Express devices. This is used to print the bus type
during init_one().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix 5780 PHY related problems:
1. MAC_RX_MODE reset must be done before setting up the MAC_MODE
register on 5705_PLUS chips or the chip will stop receiving after
a while. The MAC_RX_MODE reset is needed to prevent intermittently
losing the first receive packet on serdes chips.
2. Skip MAC loopback test on 5780 because of hardware errata. Normal
traffic including PHY loopback is not affected by the errata.
3. PHY loopback fails intermittently on 5708S and this is fixed by
putting the PHY in loopback mode first before programming the MAC
mode register. A MAC_RX_MODE reset is also added.
4. Return -EINVAL in tg3_nway_reset() if device is in TBI mode. Allow
nway_reset if 5780S is in parallel detect mode.
5. Add missing PHY IDs in KNOWN_PHY_ID() macro.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When allocating a table for mem-free HCA context, don't assume that
obj_size * nobj is an even multiple of MTHCA_TABLE_CHUNK_SIZE. In
particular, make sure we allocate at least one slot even if the table
is smaller than MTHCA_TABLE_CHUNK_SIZE.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Received from Mark Salyzyn from Adaptec.
High Priority Queues have *never* been used in the entire history of the
aac based adapters. Associated with this, aac_insert_entry can be
removed, SavedIrql can be removed & padding variable can be removed.
With the movement of SavedIrql out & replaced with an automatic variable
qflags, the locking can be refined somewhat. The sparse warnings did not
catch the need for byte swapping in the 'dprintk' debugging print
macros, so fixed this up when this code was moved outside of the now
refined locking.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec.
The size of the command packet's scatter gather list maximum size was
miscalculated in the low range leading to the driver initialization
limiting the maximum i/o size that could go to the Adapter. There were
no negative operational side effects resulting from this bad math, only
a subtle limit in performance of the Adapter at the top end of the
range.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec.
In the rare instances where the adapter, or the motherboard, is
misbehaving; driver initialization or shutdown becomes problematic. By
introducing a 3 minute timeout on the first interrupt driven command
during initialization, or the issuance of the adapter shutdown command
during driver unload, we can resolve the lockup problems induced by
common (but rare) hardware misbehaviors.
The timeout during initialization, should it occur, is accompanied by a
message presented to the console and the logs indicating that the user
should inspect and resolve problems with interrupt routing.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds some additional error return checking and error return
value propagation during initialization. Also, the deprecation of
pci_module_init with pci_register_driver along with the change in return
values.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec.
Hotplug sniffs the AIFs (events) from the adapter and if a container
change resulting in the device going offline (container zero), online
(container zero completed) or changing capacity (morph) it will take
actions by calling the appropriate API.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Recevied from Mark Salyzyn from Adaptec.
Aif pre-allocation is used to pull the kmalloc outside of the locks.
Applies to the scsi-misc-2.6 git tree.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec.
There are a few adapters that are capable of creating devices with this large
of a capacity, but now that we have the large fib support in, the management
applications will be capable of generating them. The problem is, once they are
created, the driver will not be able to access the devices correctly without
this patch.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If input message rate from userspace is too high, do not drop them,
but try to deliver using work queue allocation.
Failing there is some kind of congestion control.
It also removes warn_on on this condition, which scares people.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro pointed out that the current IB userspace verbs interface
allows userspace to cause mischief by closing file descriptors before
we're ready, or issuing the same command twice at the same time. This
patch closes those races, and fixes other obvious problems such as a
module reference leak.
Some other interface bogosities will require an ABI change to fix
properly, so I'm deferring those fixes until 2.6.15.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The loop in mthca_map_cmd() would fill one entry past the end of the
mailbox buffer before calling the firmware command.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We should use the first word of the clear interrupt register if
the bit we're after is < 32, not < 31.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If we allocate a bunch of doorbell records and then free them, we'll
end up with completely empty pages, which we then free. However, when
we come back to allocate more doorbell pages, we have to reallocate
those empty pages rather than always trying to take a slot that we've
never used. If we don't, we eventually use up every slot and fail to
allocate a doorbell record, even though we have plenty of free space.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Christian Zoz reported there are multiple NinjaATA devices all sharing the
second product ID string, but not the first one.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Adds better support for the CB-710, CB-712, CB-720 and CB-722 bridges from EnE
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Add new ID to serial_cs.c; the CIS fimware override is available by the
manufacturer at http://www.sierrawireless.com . Remember to name the CIS
binary SW_7xx_SER.cis and to put it into /lib/firmware/
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Support some more TI cardbus bridges. most of them are multifunction
devices which adds 1394 controllers, smartcard readers etc. this could
also help with the various problems with the XX21 controllers seen on the
linux-pcmcia list.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
TCIC depends on ISA. It is used with ISA-bus system only.
Signed-off-by: komurojun-mbn@nifty.com
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
pci_set_power_state is not needed, as we call pci_enable_device() somewhere
else. Also, the resource we write to PCI_BASE_ADDRESS_0 needs to be converted
to bus-centric view first.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
In interrupt probing (both ISA and PCI) the bridge control register is used
to change interrupt routing to ISA or PCI by changing bit 7. But this bit
only controls the routing of card functional interrupts, not the CSC
interrupts which are used for interrupt probing.
A bad side effect of messing with this register in yenta_probe_irq() is
that it can lead to irq storms if a card is inserted and already powered by
the BIOS.
Usage in yenta_sock_init() and yenta_config_init() seem to be fishy as well.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Echo Audio cardbus products are known to be incompatible with EnE bridges.
in order to maybe solve the problem a EnE specific test bit has to be set,
another cleared...but other setups have a good chance to break when just
forcing the bits. so do the whole thingy automatically.
The patch adds a hook in cb_alloc() that allows special tuning for the
different chipsets. for ene just match the Echo products and set/clear the
test bits, defaults to do the same thing as w/o the patch to not break
working setups.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Brown paperbag bug: sas_rphy_delete was ordered completely
wrong. Fix it up to be the same order as sas_phy_delete or
fc_rport_terminate and fix rphy objects that leaked after module
removal.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch from Ben Dooks
Fix the following warnings produced from
drivers/char/s3c2410.c.
drivers/serial/s3c2410.c:757: warning: 'clk' may be used uninitialized
drivers/serial/s3c2410.c:756: warning: 'clksrc' may be used uninitialized
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes a hole in the rport unblock handling when processing
fabric events via the ADISC/PLOGI device state machine. Original code
would not properly 'unblock' the port upon the port reloging into the
fabric.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently we just ignore the device, which means there are a few
arrays out there that we don't find.
This patch updates the scsi_report_lun_scan() to take a target instead
of a device so it can be called on a return of
SCSI_SCAN_TARGET_PRESENT, which is what a PQ 3 device returns.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The wwitch bitmap was added to input_device_id structure and we should
check it when matching handlers and input devices.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that we are compiling with -fno-strict-aliasing (this is the
kernel default), we can drop the following kludge for
iwe_stream_add_event().
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds support for WE-19 to the HostAP driver. One of
the major change is the use of an explicit flag to tell if iwstat is
in dBm or not.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
hostap_pci and hostap_plx drivers still use PCI driver names
"prism2_pci" and "prism2_plx" respectively. This is unfriendly to
linux-wlan-ng, which uses the same names. So, if e.g. hostap_pci and
prism2_pci are loaded, they will "share" /sys/bus/pci/drivers/prism2_plx
directory.
Change PCI driver names of hostap_pci and hostap_plx to be equal to
their module names.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This is one of those workarounds sucked over from sk98lin driver.
The skge driver needs to detect the Yukon-Lite A0 chip properly,
and turn of Rx FIFO Flush.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
I found an inconsistent spin_lock usage in ipmi_smi_msg_received.
Signed-off-by: Hironobu Ishii <hishii@soft.fujitsu.com>
Cc: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- fix this:
drivers/video/aty/xlinit.c: In function `atyfb_xl_init':
drivers/video/aty/xlinit.c:256: warning: ISO C90 forbids mixed declarations and code
- repair some kooky coding style
- Use ARRAY_SIZE()
Cc: Tom 'spot' Callaway <tcallawa@redhat.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
usb_unlink_urb is always async now, so URB_ASYNC_UNLINK was removed from
core USB and we must do as well.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I believe the change that broke things is introduction of
pci_fixup_parent_subordinate_busnr().
The patch here does two things:
- hunk #1 should fix the problems you've seen when you boot without
additional "pci" kernel options;
- hunk #2 supposedly fixes boot with "pci=assign-busses" option which
otherwise hangs Acer TM81xx machines as reported.
Please try this with and without "pci=assign-busses". If it boots,
I'd like to see 'lspci -vvx' for both cases.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While this is true, E8390_CMD is zero on i386, and thus there should be no
effect for these machines. Machines like Mac, Amiga etc. which use Alan's
clever register mapping may have a non-zero E8390_CMD and result in bogus
"transmitter busy" type messages from this bug.
Fixes BUG# 3991.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Read only needed data in __orinoco_ev_txexc().
Don't read the 802.11 header beyond addr1. The rest of the frame is not
used currently.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Annotate endianess of variables and structure members.
Don't reuse variables for both host-endian and little-endian data.
Minor comment changes in affected structures.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Remove unneeded forward declarations.
Also reorder struct pcmcia_driver initialization to keep attach and
detach together.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
orinoco_send_wevents() could return without unlocking.
Failure to read BSSID from the hardware would cause orinoco_send_wevents() to
return with lock held. Found by sparse.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
