If you add more than one IPv6 address belonging to the same prefix and
delete the address that was last added, routing table entry for that
prefix is also deleted.
Tested on 2.6.14.4
To reproduce:
ip addr add 3ffe::1/64 dev eth0
ip addr add 3ffe::2/64 dev eth0
/* wait DAD */
sleep 1
ip addr del 3ffe::2/64 dev eth0
ip -6 route
(route to 3ffe::/64 should be gone)
In ipv6_del_addr(), if ifa == ifp, we set ifa->if_next to NULL, and later
assign ifap = &ifa->if_next, effectively terminating the for-loop.
This prevents us from checking if there are other addresses using the same
prefix that are valid, and thus resulting in deletion of the prefix.
This applies only if the first entry in idev->addr_list is the address to
be deleted.
Signed-off-by: Kristian Slavov <kristian.slavov@nomadiclab.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A tentative address is not considered "assigned to an interface"
in the traditional sense (RFC2462 Section 4).
Don't try to select such an address for the source address.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
If the link was not available when the interface was created,
run DAD for pending tentative addresses when the link becomes ready.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
NETDEV_UP might be sent even if the link attached to the interface was
not ready. DAD does not make sense in such case, so we won't do so.
After interface
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
The route expiration time is stored in rt6i_expires in jiffies.
The argument of rt6_route_add() for adding a route is not the
expiration time in jiffies nor in clock_t, but the lifetime
(or time left before expiration) in clock_t.
Because of the confusion, we sometimes saw several strange errors
(FAILs) in TAHI IPv6 Ready Logo Phase-2 Self Test.
The symptoms were analyzed by Mitsuru Chinen <CHINEN@jp.ibm.com>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP6_NF_TARGET_NFQUEUE depends on IP6_NF_IPTABLES, not IP_NF_IPTABLES.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noticed by Andi Kleen, it is pointless to emit the device
structure pointer in the kernel logs like this.
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a simple bug which uses the wrong member.
This bug does not seriously affect ordinary use of IPsec.
But it is important to pass IPv6 ready logo phase-2
conformance test of IPsec SGW.
Signed-off-by: Kazunori MIYAZAWA <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes nf_conntrack_icmpv6 check that ICMPv6 type isn't < 128
to avoid accessing out of array valid_new[] and invmap[].
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ Modified to match inet_create() bug fix by Herbert Xu -DaveM ]
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: David Stevens <dlstevens@us.ibm.com>
As explained at:
http://www.cs.ucsb.edu/~krishna/igmp_dos/
With IGMP version 1 and 2 it is possible to inject a unicast
report to a client which will make it ignore multicast
reports sent later by the router.
The fix is to only accept the report if is was sent to a
multicast or unicast address.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes two needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
the patch below marks various variables const in net/; the goal is to
move them to the .rodata section so that they can't false-share
cachelines with things that get written to, as well as potentially
helping gcc a bit with optimisations. (these were found using a gcc
patch to warn about such variables)
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure to update hiscore.rule in dummy rule 4 in ipv6_dev_get_saddr().
Pointed out by Yan Zheng <yanzheng@21cn.com>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
addrconf_verify(...) only traverse address hash table when
addrconf_hash_lock is held for writing, and it may hold
addrconf_hash_lock for a long time. So I think it's better to acquire
addrconf_hash_lock for reading instead of writing
Signed-off-by: Yan Zheng <yanzheng@21cn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both of ipq and frag_queue have *next and **prev, and they can be replaced
with hlist. Thanks Arnaldo Carvalho de Melo for the suggestion.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch below fixes the following sparse warning:
net/ipv6/ipv6_sockglue.c:291:13: warning: Using plain integer as NULL pointer
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "score.rule++" doesn't make any sense for me.
According to codes above, I think it should be "hiscore.rule++;" .
Signed-off-by: Yan Zheng<yanzheng@21cn.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes nf_conntrack_ipv6 free all IPv6 fragment queues at module
unloading time. Also introduce a BUG_ON if we ever again have leaks in
the memory accounting.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This synchronizes nf_ct_reasm with ipv6 reassembly, and fixes a possibility
of an infinite loop if CPUs evict and create nf_ct_frag6_queue in parallel.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
These variables should be unsigned. This fixes sysctl handler for
nf_ct_frag6_{low,high}_thresh.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes linux 2.4 configs in comments as TODO lists.
And this also move the entry of nf_conntrack to top like IPv4 Netfilter
Kconfig.
Based on original patch by Krzysztof Piotr Oledzki <ole@ans.pl>.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent change to netlink dump "done" callback handling broke IPv6
which played dirty tricks with the "done" callback. This causes an
infinite loop during a dump.
The following patch fixes it.
This bug was reported by Jeff Garzik.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based mostly upon a patch from Olaf Kirch <okir@suse.de>
When initialization fails in inet6_init(), we should
unregister the PF_INET6 socket ops.
Also, check sock_register()'s return value for errors.
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the patch that introduces the generic skb_checksum_complete
which also checks for hardware RX checksum faults. If that happens,
it'll call netdev_rx_csum_fault which currently prints out a stack
trace with the device name. In future it can turn off RX checksum.
I've converted every spot under net/ that does RX checksum checks to
use skb_checksum_complete or __skb_checksum_complete with the
exceptions of:
* Those places where checksums are done bit by bit. These will call
netdev_rx_csum_fault directly.
* The following have not been completely checked/converted:
ipmr
ip_vs
netfilter
dccp
This patch is based on patches and suggestions from Stephen Hemminger
and David S. Miller.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most netlink families make no use of the done() callback, making
it optional gets rid of all unnecessary dummy implementations.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Trying to build today's 2.6.14+git snapshot gives undefined references
to use_tempaddr
Looks like an ifdef got left out.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Jesper Juhl <jesper.juhl@gmail.com>
This is the net/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in net/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Arnaldo Carvalho de Melo <acme@conectiva.com.br>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Choose more appropriate source address; e.g.
- outgoing interface
- non-deprecated
- scope
- matching label
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch randomizes the port selected on bind() for connections
to help with possible security attacks. It should also be faster
in most cases because there is no need for a global lock.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
And filter mode is exclude.
Further explanation by David Stevens:
Multicast source filters aren't widely used yet, and that's really the only
feature that's affected if an application actually exercises this bug, as far
as I can tell. An ordinary filter-less multicast join should still work, and
only forwarded multicast traffic making use of filters and doing empty-source
filters with the MSFILTER ioctl would be at risk of not getting multicast
traffic forwarded to them because the reports generated would not be based on
the correct counts.
Signed-off-by: Yan Zheng <yanzheng@21cn.com
Acked-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
I find that linux will reply echo request destined to an address which
belongs to an interface other than the one from which the request received.
This behavior doesn't make sense for link local address.
YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> said:
Please note that sender does need to setup neighbor entry by hand to reproduce
this bug. (Link-local address on eth1 is not visible on eth0, from the point
of view of neighbor discovery in IPv6.)
+--------+ +--------+
| sender | | router |
+---+----+ +-+----+-+
|eth0 eth0| |eth1
-----+----------------------+- -+--------------
Signed-off-by: Yan Zheng <yanzheng@21cn.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Andrew Morton <akpm@osdl.org> (forwarded)
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Like ip_tables already has it for some time, this adds support for
having multiple revisions for each match/target. We steal one byte from
the name in order to accomodate a 8 bit version number.
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
