Commit Graph

554 Commits

Author SHA1 Message Date
Linus Walleij
897a6a1a14 ARM: davinci: fix cache flush build error
The TNET variant of DaVinci compiles some code that it shares
with other DaVinci variants, however it has a V6 CPU rather than
an ARM926T, thus the hardcoded call to arm926_flush_kern_cache_all()
in sleep.S will obviously fail, and we need to build with the
v6_flush_kern_cache_all() call instead. This was triggered by
manually altering the DaVinci config to build the TNET version.

Cc: Dave Martin <dave.martin@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Cc: stable@kernel.org
2011-09-07 17:22:12 +05:30
Sergei Shtylyov
c08748005d ARM: davinci: correct MDSTAT_STATE_MASK
MDSTAT.STATE occupies bits 0..5 according to all available documentation, so fix
the #define MDSTAT_STATE_MASK at last. Using the wrong value seems to have been
harmless though...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2011-09-07 14:23:02 +05:30
Rajashekhara, Sudhakar
810198bc9c ARM: davinci: da850 EVM: read mac address from SPI flash
DA850/OMAP-L138 EMAC driver uses random mac address instead of
a fixed one because the mac address is not stuffed into EMAC
platform data.

This patch provides a function which reads the mac address
stored in SPI flash (registered as MTD device) and populates the
EMAC platform data. The function which reads the mac address is
registered as a callback which gets called upon addition of MTD
device.

NOTE: In case the MAC address stored in SPI flash is erased, follow
the instructions at [1] to restore it.

[1] http://processors.wiki.ti.com/index.php/GSG:_OMAP-L138_DVEVM_Additional_Procedures#Restoring_MAC_address_on_SPI_Flash

Modifications in v2:
Guarded registering the mtd_notifier only when MTD is enabled.
Earlier this was handled using mtd_has_partitions() call, but
this has been removed in Linux v3.0.

Modifications in v3:
a. Guarded da850_evm_m25p80_notify_add() function and
   da850evm_spi_notifier structure with CONFIG_MTD macros.
b. Renamed da850_evm_register_mtd_user() function to
   da850_evm_setup_mac_addr() and removed the struct mtd_notifier
   argument to this function.
c. Passed the da850evm_spi_notifier structure to register_mtd_user()
   function.

Modifications in v4:
Moved the da850_evm_setup_mac_addr() function within the first
CONFIG_MTD ifdef construct.

Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Cc: stable@kernel.org
2011-09-07 14:23:01 +05:30
Linus Torvalds
69f1d1a6ac Merge branch 'next/devel' of ssh://master.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'next/devel' of ssh://master.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (128 commits)
  ARM: S5P64X0: External Interrupt Support
  ARM: EXYNOS4: Enable MFC on Samsung NURI
  ARM: EXYNOS4: Enable MFC on universal_c210
  ARM: S5PV210: Enable MFC on Goni
  ARM: S5P: Add support for MFC device
  ARM: EXYNOS4: Add support FIMD on SMDKC210
  ARM: EXYNOS4: Add platform device and helper functions for FIMD
  ARM: EXYNOS4: Add resource definition for FIMD
  ARM: EXYNOS4: Change devname for FIMD clkdev
  ARM: SAMSUNG: Add IRQ_I2S0 definition
  ARM: SAMSUNG: Add platform device for idma
  ARM: EXYNOS4: Add more registers to be saved and restored for PM
  ARM: EXYNOS4: Add more register addresses of CMU
  ARM: EXYNOS4: Add platform device for dwmci driver
  ARM: EXYNOS4: configure rtc-s3c on NURI
  ARM: EXYNOS4: configure MAX8903 secondary charger on NURI
  ARM: EXYNOS4: configure ADC on NURI
  ARM: EXYNOS4: configure MAX17042 fuel gauge on NURI
  ARM: EXYNOS4: configure regulators and PMIC(MAX8997) on NURI
  ARM: EXYNOS4: Increase NR_IRQS for devices with more IRQs
  ...

Fix up tons of silly conflicts:
 - arch/arm/mach-davinci/include/mach/psc.h
 - arch/arm/mach-exynos4/Kconfig
 - arch/arm/mach-exynos4/mach-smdkc210.c
 - arch/arm/mach-exynos4/pm.c
 - arch/arm/mach-imx/mm-imx1.c
 - arch/arm/mach-imx/mm-imx21.c
 - arch/arm/mach-imx/mm-imx25.c
 - arch/arm/mach-imx/mm-imx27.c
 - arch/arm/mach-imx/mm-imx31.c
 - arch/arm/mach-imx/mm-imx35.c
 - arch/arm/mach-mx5/mm.c
 - arch/arm/mach-s5pv210/mach-goni.c
 - arch/arm/mm/Kconfig
2011-07-26 17:41:04 -07:00
Linus Torvalds
3960ef326a Merge branch 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
  ARM: Consolidate the clkdev header files
  ARM: set vga memory base at run-time
  ARM: convert PCI defines to variables
  ARM: pci: make pcibios_assign_all_busses use pci_has_flag
  ARM: remove unnecessary mach/hardware.h includes
  pci: move microblaze and powerpc pci flag functions into asm-generic
  powerpc: rename ppc_pci_*_flags to pci_*_flags

Fix up conflicts in arch/microblaze/include/asm/pci-bridge.h
2011-07-26 17:12:10 -07:00
Linus Torvalds
ae4c42e4e4 Merge branch 'next/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'next/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (133 commits)
  ARM: EXYNOS4: Change devname for FIMD clkdev
  ARM: S3C64XX: Cleanup mach/regs-fb.h from mach-s3c64xx
  ARM: S5PV210: Cleanup mach/regs-fb.h from mach-s5pv210
  ARM: S5PC100: Cleanup mach/regs-fb.h from mach-s5pc100
  ARM: S3C24XX: Use generic s3c_set_platdata for devices
  ARM: S3C64XX: Use generic s3c_set_platdata for OneNAND
  ARM: SAMSUNG: Use generic s3c_set_platdata for NAND
  ARM: SAMSUNG: Use generic s3c_set_platdata for USB OHCI
  ARM: SAMSUNG: Use generic s3c_set_platdata for HWMON
  ARM: SAMSUNG: Use generic s3c_set_platdata for FB
  ARM: SAMSUNG: Use generic s3c_set_platdata for TS
  ARM: S3C64XX: Add PWM backlight support on SMDK6410
  ARM: S5P64X0: Add PWM backlight support on SMDK6450
  ARM: S5P64X0: Add PWM backlight support on SMDK6440
  ARM: S5PC100: Add PWM backlight support on SMDKC100
  ARM: S5PV210: Add PWM backlight support on SMDKV210
  ARM: EXYNOS4: Add PWM backlight support on SMDKC210
  ARM: EXYNOS4: Add PWM backlight support on SMDKV310
  ARM: SAMSUNG: Create a common infrastructure for PWM backlight support
  clocksource: convert 32-bit down counting clocksource on S5PV210/S5P64X0
  ...

Fix up trivial conflict in arch/arm/mach-imx/mach-scb9328.c
2011-07-25 12:38:42 -07:00
Linus Torvalds
b6844e8f64 Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (237 commits)
  ARM: 7004/1: fix traps.h compile warnings
  ARM: 6998/2: kernel: use proper memory barriers for bitops
  ARM: 6997/1: ep93xx: increase NR_BANKS to 16 for support of 128MB RAM
  ARM: Fix build errors caused by adding generic macros
  ARM: CPU hotplug: ensure we migrate all IRQs off a downed CPU
  ARM: CPU hotplug: pass in proper affinity mask on IRQ migration
  ARM: GIC: avoid routing interrupts to offline CPUs
  ARM: CPU hotplug: fix abuse of irqdesc->node
  ARM: 6981/2: mmci: adjust calculation of f_min
  ARM: 7000/1: LPAE: Use long long printk format for displaying the pud
  ARM: 6999/1: head, zImage: Always Enter the kernel in ARM state
  ARM: btc: avoid invalidating the branch target cache on kernel TLB maintanence
  ARM: ARM_DMA_ZONE_SIZE is no more
  ARM: mach-shark: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ARM: mach-sa1100: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ARM: mach-realview: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ARM: mach-pxa: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ARM: mach-ixp4xx: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ARM: mach-h720x: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ARM: mach-davinci: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ...
2011-07-24 10:20:54 -07:00
Russell King
3ad55155b2 Merge branch 'devel-stable' into for-next
Conflicts:
	arch/arm/kernel/entry-armv.S
2011-07-22 23:09:07 +01:00
Russell King
06f365acef Merge branches 'btc', 'dma', 'entry', 'fixes', 'linker-layout', 'misc', 'mmci', 'suspend' and 'vfp' into for-next 2011-07-22 23:08:48 +01:00
David S. Miller
033b1142f4 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	net/bluetooth/l2cap_core.c
2011-07-21 13:38:42 -07:00
Linus Torvalds
47126d807a Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
  davinci: DM365 EVM: fix video input mux bits
  ARM: davinci: Check for NULL return from irq_alloc_generic_chip
  arm: davinci: Fix low level gpio irq handlers' argument
2011-07-19 22:10:05 -07:00
Kyungmin Park
aa3831cf9d ARM: Consolidate the clkdev header files
Now most of ARM machines has the alsmot same __clk_get/put() macro

So place it at the arch/arm/include/asm/clkdev.h and remove the reduntant header files

But some machines don't have the same form as above. It can use the machince specific clkdev file by HAVE_MACH_CLKDEV config

Now there are only 3 caese.

1) define the clk structure with clkdev macro => Need to move clk structure to proper header file

arch/arm/mach-versatile/include/mach/clkdev.h
arch/arm/mach-realview/include/mach/clkdev.h
arch/arm/mach-vexpress/include/mach/clkdev.h
arch/arm/mach-integrator/include/mach/clkdev.h

2) export the __clk_get/put function at clock.c

arch/arm/mach-shmobile/include/mach/clkdev.h

3) demuxing the clk source
arch/arm/mach-u300/include/mach/clkdev.h

Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2011-07-19 18:09:45 +02:00
Jon Povey
9daedd833a davinci: DM365 EVM: fix video input mux bits
Video input mux settings for tvp7002 and imager inputs were swapped.
Comment was correct.

Tested on EVM with tvp7002 input.

Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Acked-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: stable@kernel.org
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2011-07-19 14:00:29 +05:30
Todd Poynor
33e1e5e317 ARM: davinci: Check for NULL return from irq_alloc_generic_chip
Avoid NULL dereference of irq_alloc_generic_chip return in low
memory conditions.

Signed-off-by: Todd Poynor <toddpoynor@google.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2011-07-19 12:49:00 +05:30
Nicolas Pitre
f68deabf3d ARM: mach-davinci: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
2011-07-18 15:29:58 -04:00
David S. Miller
6a7ebdf2fd Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	net/bluetooth/l2cap_core.c
2011-07-14 07:56:40 -07:00
Ido Yariv
f299bb9527 arm: davinci: Fix low level gpio irq handlers' argument
Commit 7416401 ("arm: davinci: Fix fallout from generic irq chip
conversion") introduced a bug, causing low level interrupt handlers to
get a bogus irq number as an argument. The gpio irq handler falsely
assumes that the handler data is the irq base number and that is no
longer true.

Set the irq handler data to be a pointer to the corresponding gpio
controller. The chained irq handler can then use it to extract both the
irq base number and the gpio registers structure.

Signed-off-by: Ido Yariv <ido@wizery.com>
CC: Thomas Gleixner <tglx@linutronix.de>
[nsekhar@ti.com: renamed "ctl" to "d", simplified indexing logic for chips and
took care of odd bank handling in irq handler]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2011-07-12 14:21:43 +05:30
Sekhar Nori
8bb2c4813c davinci: da850 evm: register SATA device
Register the platform device for SATA interface
present on the DA850/OMAP-L138/AM18x EVM.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2011-07-08 11:14:50 +05:30
Sekhar Nori
cbb2c9617a davinci: da850: add support for SATA interface
Add support for SATA controller on the
DA850/OMAP-L138/AM18x devices.

The patch adds the necessary clocks, platform
resources and a routine to initialize the SATA
controller.

The PHY configuration in this patch is
courtesy the work done by Zegeye Alemu,
Swaminathan and Mansoor Ahamed from TI.

While testing this patch, enable port multiplier
support iff you are actually using one. The
reasons of this behaviour are discussed
here: http://patchwork.ozlabs.org/patch/78163/

ChangeLog:
v3:
Removed fields which were being initialized
to zero in PHY configuration. Moved SATA base
address definition to the top of the file to
make it inline with what is done for the rest
of the modules.
v2:
Addressed comments from Sergei. Removed unnecessary
braces and removed unnecessary else after goto.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2011-07-08 11:13:08 +05:30
Sekhar Nori
aad70de20f davinci: enable forced transitions on PSC
Some DaVinci modules like the SATA on DA850
need forced module state transitions.

Define a "force" flag which can be passed to
the PSC config function to enable it to make
forced transitions.

Forced transitions shouldn't normally be attempted,
unless the TRM explicitly specifies its usage.

ChangeLog:
v2:
Modified to take care of the fact that
davinci_psc_config() now takes the flags
directly.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2011-07-08 11:10:09 +05:30
Sekhar Nori
a51ca38b63 davinci: pass clock flags to davinci_psc_config()
Enabling or disabling a PSC can take certain
modifiers like "disable with reset", "force
enable/disable" and "enable/disable with local
reset" apart from the regular clock gating
functionality.

Pass a flags argument to davinci_psc_config()
so these variations can be supported there.

At this time only "disable with reset" is
supported, but other functionality will be
added in subsequent patches.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2011-07-08 10:51:40 +05:30
Simon Guinot
659fb32d1b genirq: replace irq_gc_ack() with {set,clr}_bit variants (fwd)
This fixes a regression introduced by e59347a "arm: orion:
Use generic irq chip".

Depending on the device, interrupts acknowledgement is done by setting
or by clearing a dedicated register. Replace irq_gc_ack() with some
{set,clr}_bit variants allows to handle both cases.

Note that this patch affects the following SoCs: Davinci, Samsung and
Orion. Except for this last, the change is minor: irq_gc_ack() is just
renamed into irq_gc_ack_set_bit().

For the Orion SoCs, the edge GPIO interrupts support is currently
broken. irq_gc_ack() try to acknowledge a such interrupt by setting
the corresponding cause register bit. The Orion GPIO device expect the
opposite. To fix this issue, the irq_gc_ack_clr_bit() variant is used.

Tested on Network Space v2.

Reported-by: Joey Oravec <joravec@drewtech.com>
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2011-07-07 16:02:26 +00:00
Christian Riesch
8d54297b90 davinci: da850: add a .set_rate method to ref_clk
This patch allows setting the input clock frequency of the SoC from
the board specific code using the davinci_set_refclk_rate function.

Suggested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2011-07-06 22:07:30 +05:30
Sekhar Nori
56e580d778 davinci: dm6467/T EVM: fix setting up of reference clock rate
The DM6467 and DM6467T EVMs use different reference clock
frequencies. This difference is currently supported by having
the SoC code call a public board routine which sets up the reference
clock frequency. This does not scale as more boards are added.

Instead, use the clk_set_rate() API to setup the reference clock
frequency to a different value from the board file.

Suggested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
2011-07-06 16:48:45 +05:30
Sekhar Nori
0c6fce5eb6 davinci: psc.h: clean up indentation done using spaces
psc.h has indentation using spaces at a number of places.
Fix this by indenting using tabs instead.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2011-07-06 15:44:12 +05:30
Russell King
b6fcd313c9 ARM: entry: remove unused irq_prio_table macro
Platforms provide an empty irq_prio_table macro, and as nothing uses
this macro, it can simply be removed.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-06-28 10:34:58 +01:00
Alexey Dobriyan
b7f080cfe2 net: remove mm.h inclusion from netdevice.h
Remove linux/mm.h inclusion from netdevice.h -- it's unused (I've checked manually).

To prevent mm.h inclusion via other channels also extract "enum dma_data_direction"
definition into separate header. This tiny piece is what gluing netdevice.h with mm.h
via "netdevice.h => dmaengine.h => dma-mapping.h => scatterlist.h => mm.h".
Removal of mm.h from scatterlist.h was tried and was found not feasible
on most archs, so the link was cutoff earlier.

Hope people are OK with tiny include file.

Note, that mm_types.h is still dragged in, but it is a separate story.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-06-21 19:17:20 -07:00
Sekhar Nori
7e9f194521 davinci: make PCM platform devices static
Make the PCM device structures used in devices.c
and devices-da8xx.c static as they are used only
in the respective files.

This was found when trying to build a single image
for DaVinci and DA8x devices using runtime P2V support.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2011-06-08 14:41:37 +05:30
Thomas Gleixner
7416401661 arm: davinci: Fix fallout from generic irq chip conversion
The code which does the chained handler setup was overwriting
chip_data.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Holger Hans Peter Freyther <holger@freyther.de>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2011-06-08 14:33:52 +05:30
Russell King
014322dac6 Merge branch 'davinci-next' of git://gitorious.org/linux-davinci/linux-davinci into devel-stable 2011-05-25 00:11:25 +01:00
Russell King
9a55d9752d Merge branch 'devel-stable' into for-linus
Conflicts:
	arch/arm/Kconfig
	arch/arm/mach-ns9xxx/include/mach/uncompress.h
2011-05-23 19:28:04 +01:00
Russell King
4b60e5f90d Merge branches 'consolidate-clksrc', 'consolidate-flash', 'consolidate-generic', 'consolidate-smp', 'consolidate-stmp' and 'consolidate-zones' into consolidate 2011-05-23 18:05:10 +01:00
Manjunath Hadli
1a717c0050 davinci: move DM64XX_VDD3P3V_PWDN to devices.c
Move the definition of DM64XX_VDD3P3V_PWDN from hardware.h
to devices.c since it is used only there.

This also helps rid hardware.h of platform private stuff.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2011-05-23 22:18:26 +05:30
Linus Torvalds
f8223b1755 Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] remove redundant sprintf from request_module call.
  [CPUFREQ] cpufreq_stats.c: Fixed brace coding style issue
  [CPUFREQ] Fix memory leak in cpufreq_stat
  [CPUFREQ] cpufreq.h: Fix some checkpatch.pl coding style issues.
  [CPUFREQ] use dynamic debug instead of custom infrastructure
  [CPUFREQ] CPU hotplug, re-create sysfs directory and symlinks
  [CPUFREQ] Fix _OSC UUID in pcc-cpufreq
2011-05-19 15:57:29 -07:00
Russell King
be20902ba6 ARM: use ARM_DMA_ZONE_SIZE to adjust the zone sizes
Rather than each platform providing its own function to adjust the
zone sizes, use the new ARM_DMA_ZONE_SIZE definition to perform this
adjustment.  This ensures that the actual DMA zone size and the
ISA_DMA_THRESHOLD/MAX_DMA_ADDRESS definitions are consistent with
each other, and moves this complexity out of the platform code.

Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-05-12 08:36:53 +01:00
Russell King
2fb3ec5c95 ARM: Replace platform definition of ISA_DMA_THRESHOLD/MAX_DMA_ADDRESS
The values of ISA_DMA_THRESHOLD and MAX_DMA_ADDRESS are related; one is
the physical/bus address, the other is the virtual address.  Both need
to be kept in step, so rather than having platforms define both, allow
them to define a single macro which sets both of these macros
appropraitely.

Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-05-12 08:36:49 +01:00
Russell King
805499a6d5 Merge branch 'irq-davinci' of git://gitorious.org/linux-davinci/linux-davinci into devel-stable 2011-05-11 18:49:31 +01:00
Thomas Gleixner
aac4dd1dab arm: davinci: Use generic irq chip
Simple conversion which simply uses the fact that the second irq chip
base address has offset 0x04 to the first one.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-and-Tested-by: Kevin Hilman <khilman@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
2011-05-11 22:40:06 +05:30
Russell King
7b76415375 Merge branch 'zImage_fixes' of git://git.linaro.org/people/nico/linux into devel-stable 2011-05-07 08:34:02 +01:00
Nicolas Pitre
8ea0de4b88 ARM: zImage: remove the static qualifier from global data variables
To be able to relocate the .bss section at run time independently from
the rest of the code, we must make sure that no GOTOFF relocations are
used with .bss symbols.  This usually means that no global variables can
be marked static unless they're also const.

Let's remove the static qualifier from current offenders, or turn them
into const variables when possible.  Next commit will ensure the build
fails if one of those is reintroduced due to otherwise enforced coding
standards for the kernel.

Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
2011-05-07 00:08:02 -04:00
Sergei Shtylyov
8ac764e347 DA8xx: move base address #define's to their proper place
Move DA8XX_MMCSD0_BASE, DA8XX_LCD_CNTRL_BASE,  and DA8XX_DDR2_CTL_BASE from
<mach/da8xx.h> to devices-da8xx.c as the latter file is the only place where
these macros are used.

While at it, restore sorting the base address macros by address value in
devices-da8xx.c...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
2011-05-06 12:10:54 +05:30
Sergei Shtylyov
e0c199d098 DA8xx: kill duplicate #define DA8XX_PLL1_BASE
Commit 044ca01521 (davinci: da850/omap-l138: add
support for SoC suspend) introduced DA8XX_PLL1_BASE despite PLL1 exists only on
DA850/OMAP-L138 and da850.c even already #define'd DA850_PLL1_BASE. Kill the
duplicate macro, renaming an existing reference to it...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
2011-05-06 12:10:54 +05:30
Sergei Shtylyov
5a9f68fd26 DA8xx: kill duplicate #define DA8XX_GPIO_BASE
DA8XX_GPIO_BASE is #define'd in both <mach/da8xx.h> and devices-da8xx.c;
moreover, it's not even used in the latter file...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
2011-05-06 12:10:53 +05:30
Dominik Brodowski
2d06d8c49a [CPUFREQ] use dynamic debug instead of custom infrastructure
With dynamic debug having gained the capability to report debug messages
also during the boot process, it offers a far superior interface for
debug messages than the custom cpufreq infrastructure. As a first step,
remove the old cpufreq_debug_printk() function and replace it with a call
to the generic pr_debug() function.

How can dynamic debug be used on cpufreq? You need a kernel which has
CONFIG_DYNAMIC_DEBUG enabled.

To enabled debugging during runtime, mount debugfs and

$ echo -n 'module cpufreq +p' > /sys/kernel/debug/dynamic_debug/control

for debugging the complete "cpufreq" module. To achieve the same goal during
boot, append

	ddebug_query="module cpufreq +p"

as a boot parameter to the kernel of your choice.

For more detailled instructions, please see
Documentation/dynamic-debug-howto.txt

Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
2011-05-04 11:50:57 -04:00
Linus Torvalds
625a3b6057 Merge branch 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm: (47 commits)
  CLKDEV: Fix clkdev return value for NULL clk case
  ARM: 6891/1: prevent heap corruption in OABI semtimedop
  ARM: kprobes: Tidy-up kprobes-decode.c
  ARM: kprobes: Add emulation of hint instructions like NOP and WFI
  ARM: kprobes: Add emulation of SBFX, UBFX, BFI and BFC instructions
  ARM: kprobes: Add emulation of MOVW and MOVT instructions
  ARM: kprobes: Reject probing of undefined data processing instructions
  ARM: kprobes: Remove redundant code in space_1111
  ARM: kprobes: Fix emulation of PLD instructions
  ARM: kprobes: Reject probing of SETEND instructions
  ARM: kprobes: Consolidate stub decoding functions
  ARM: kprobes: Reject probing of all coprocessor instructions
  ARM: kprobes: Fix emulation of USAD8 instructions
  ARM: kprobes: Fix emulation of SMUAD, SMUSD and SMMUL instructions
  ARM: kprobes: Fix emulation of SXTB16, SXTB, SXTH, UXTB16, UXTB and UXTH instructions
  ARM: kprobes: Reject probing of undefined media instructions
  ARM: kprobes: Add emulation of RBIT instruction
  ARM: kprobes: Reject probing of LDRB instructions which load PC
  ARM: kprobes: Fix emulation of LDRD and STRD instructions
  ARM: kprobes: Reject probing of LDR/STR instructions which update PC unpredictably
  ...
2011-05-02 12:17:05 -07:00
Lucas De Marchi
e9c549998d Revert wrong fixes for common misspellings
These changes were incorrectly fixed by codespell. They were now
manually corrected.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2011-04-26 23:31:11 -07:00
Russell King - ARM Linux
45b146d746 ARM: Davinci: Fix I2C build errors
Several Davinci platforms select the I2C EEPROM support, but don't
select I2C support.  This causes I2C EEPROM support to be built into
the kernel, but I2C support may not be configured to be built in.
This leads to linker errors due to missing I2C symbols.

Arrange for I2C to be selected whenever EEPROM_AT24 is selected.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2011-04-25 14:19:32 +05:30
Sergei Shtylyov
9e7d24f622 DA830: fix SPI1 base address
Commit 54ce6883d2 (davinci: da8xx: add spi
resources and registration routine) wrongly assumed that SPI1 is mapped at
the same address on DA830/OMAP-L137 and DA850/OMAP-L138; actually, the base
address was valid only for the latter SoC. Teach the code to pass the correct
SPI1 memory resource for both SoCs...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2011-04-25 14:19:31 +05:30
Michael Williamson
336f402790 davinci: mityomapl138: Use auto-probe to determine attached PHY ID
Current board configurations involving the MityDSP-L138 and MityARM-1808
only have one attached PHY, but it's address may not be the same.  Default
the behavior to auto-probe for the PHY and use the first one found.

Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2011-04-25 14:19:31 +05:30
Michael Williamson
ad10e1051e davinci: mityomapl138: Use correct id for NAND controller
For the MityDSP-L138/MityARM-1808 SOMS, the NAND controller id (which needs
to correspond to the chipselect, and is used for controlling the HW ECC
computation) is not correct.  Fix it.

Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2011-04-25 14:18:48 +05:30