Commit Graph

2281 Commits

Author SHA1 Message Date
Tomi Valkeinen
da91e89fb2 OMAP: Apollon: Port the display driver to new DSS2
Port the old omapfb panel driver to DSS2. This patch changes the board
file only, the driver is ported in separate patch.

Cc: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:21:05 +03:00
Tomi Valkeinen
cbf1455bfc OMAP: H4: Port the display driver to new DSS2
Port the old omapfb panel driver to DSS2. This patch changes the board
file only, the driver is ported in separate patch.

Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:21:05 +03:00
Tomi Valkeinen
14dd72d854 OMAP: LDP: Port the display driver to new DSS2
Port the old omapfb panel driver to DSS2. This patch changes the board
file only, the driver is ported in separate patch.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stanley Miao <stanley.miao@windriver.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:21:04 +03:00
Tomi Valkeinen
6e896ff9ff OMAP: 2420SDP: Port the display driver to new DSS2
Port the old omapfb panel driver to DSS2. This patch changes the board
file only, the driver is ported in separate patch.

Cc: Hunyue Yau <hyau@mvista.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:21:04 +03:00
Tomi Valkeinen
1382f897e6 OMAP: omap3touchbook: Remove unused lcd stuff
board-omap3touchbook.c adds an LCD device, but the kernel doesn't
contain a driver for the device. So let's remove the unneeded LCD
device.

Cc: Gregoire Gentil <gregoire@gentil.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:21:04 +03:00
Tomi Valkeinen
cc93473525 OMAP: RX51: Remove unused old omapfb stuff
RX51 uses the new DSS2 display driver, but the board file still
contained some code for the old omapfb driver. The old code can be
removed.

Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:21:03 +03:00
Tomi Valkeinen
bfdf7ab110 OMAP4: 4430SDP: Add picodlp support to board file
An on-board projector named picodlp is available for OMAP4430 SDP.

Entry for this picodlp as a panel is being added in dss_devices array to
the board file.  It needs 4 GPIO pins for interfacing with host
processor and these are defined and two of them are configured in board
file.  Two GPIOs power_on and display_select are configured here.
picodlp also needs an i2c client over i2c controller-2 at address 0x1b.

Signed-off-by: Mayuresh Janorkar <mayur@ti.com>
Signed-off-by: Mythri P K <mythripk@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:17:45 +03:00
Tomi Valkeinen
12595d46bf OMAP4: 4430SDP: Add panel support to board file
4430SDP has two Taal DSI panels, connected to DSI 1 and DSI 2 modules.
The panels use a common PWM backlight, which will be implemented later
when the PWM driver has been improved to support the backlight.

Until the PWM driver has been improved, the following hack added to
arch/arm/mach-omap2/board-4430sdp.c can be used to set the backlight to
max:

static int omap_4430sdp_hack_backlight(void)
{
       twl_i2c_write_u8(TWL_MODULE_PWM, 0x7f, LED_PWM2OFF);
       twl_i2c_write_u8(TWL_MODULE_PWM, 0x7f, LED_PWM2ON);
       twl_i2c_write_u8(TWL6030_MODULE_ID1, 0x30, TWL6030_TOGGLE3);
       return 0;
}
late_initcall(omap_4430sdp_hack_backlight);

Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:17:37 +03:00
Tomi Valkeinen
4010c07c23 OMAP: 4430SDP: Remove unneeded lcd config
4430SDP board file contains some unused old LCD configurations. They are
not used and can be removed.

Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:17:33 +03:00
Tomi Valkeinen
fcca719430 OMAP: Add DDC i2c_bus_num to board files
Add i2c bus number for DVI output for boards with DVI output where the
i2c bus has been confirmed to be connected and working. The driver uses
this to detect if a panel is connected and to read EDID.

Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:59 +03:00
Tomi Valkeinen
870e1a7359 OMAP: stalker: Remove LCD device from board file
OMAP3 Stalker board has definitions for LCD, but uses the generic driver
without any information what kind of LCD it has. The board should use a
particular panel type from panel-generic-dpi driver, not the generic
one.

As I haven't gotten response the signer-off of stalker board about the
issue, this patch removes the LCD support from the board file. This will
allow us to clean up the panel-generic-dpi driver and make it support
only fixed size panels.

CC: Jason Lam <lzg@ema-tech.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:53 +03:00
Tomi Valkeinen
1d7a8654e8 OMAP: use dvi panel driver instead of generic-dpi
Multiple OMAP3/4 boards have a DVI framer output. This patch makes the
boards use the new panel-dvi driver, instead of the panel-generic-dpi
driver.

Separate drivers for fixed size panels and DVI framer gives us cleaner
driver code.

Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:48 +03:00
Tomi Valkeinen
8d88767a43 OMAP: DSS2: HDMI: use default dividers
Use default regn and regm2 dividers in the hdmi driver if the board file
does not define them.

Cc: Mythri P K <mythripk@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:36 +03:00
Thomas Weber
cc11aaf867 OMAP: Devkit8000: Change lcd driver to AT070TN83
Change lcd driver from generic to AT070TN83.

Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:25 +03:00
Tomi Valkeinen
dc35835c6f OMAP: DSS2: Implement dsi_mux_pads for OMAP4
Implement dsi_mux_pads for OMAP4. On enable the function enables the DSI
pins and disables pull down. On disable the function disables the pins
and enables pull down.

It is unclear from the TRM whether the pull down is active if the pins
are disabled, so this implementation may leave the pins floating when
the DSI device is disabled.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:17 +03:00
Tomi Valkeinen
5bc416cba1 OMAP: DSS2: DSI: Improve dsi_mux_pads parameters
dsi_mux_pads() needs to know about the DSI HW module and the DSI lanes
used. Split the function into two, enable and disable, which take
necessary arguments, and add empty implementations for both.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:17 +03:00
Tomi Valkeinen
4e6a0ab0f9 OMAP4: TWL: Add common omapdss supplies
OMAP DSS normally gets power from VCXIO on OMAP4. Add configuration for
this into twl-common.c

Mark VCXIO as always_on, as VCXIO is used by multiple components,
including the MPU, and turning it off when DSS doesn't need it would
lead the device to halt.

Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:12 +03:00
Tomi Valkeinen
7c68dd96d5 OMAP: DSS2: Change DSI device naming
Currently, there are 2 differently named platform devices generated for
the 2 DSS DSI modules. In order to use the same driver, the dsi devices
should be 2 instances of the same platform device.

Change the platform device names from "omapdss_dsi1" and "omapdss_dsi2"
to omapdss_dsi", and set the device indices to 0 and 1.

Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:05 +03:00
Paul Walmsley
876355014c Merge branches 'non_hwmod_compliant_fix_3.1rc', 'omap3_clock_fixes_3.1rc', 'omap4_clock_fixes_3.1rc', 'missing_2430_musb_adds_terminator_fix_3.1rc' and 'pwrdm_clkdm_fixes_3.1rc' into prcm-fixes-a-3.1rc 2011-09-04 20:21:16 -06:00
Paul Walmsley
10167873a4 OMAP2430: hwmod: musb: add missing terminator to omap2430_usbhsotg_addrs[]
Add a missing array terminator to omap2430_usbhsotg_addrs[].  Without
this terminator, the omap_hwmod resource building code runs off the
end of the array, resulting in at least this error -- if not worse
behavior:

[    0.578002] musb-omap2430: failed to claim resource 4
[    0.583465] omap_device: musb-omap2430: build failed (-16)
[    0.589294] Could not build omap_device for musb-omap2430 usb_otg_hs

This should have been part of commit
78183f3fdf ("omap_hwmod: use a null
structure record to terminate omap_hwmod_addr_space arrays") but was
evidently missed.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
2011-09-04 20:20:53 -06:00
Paul Walmsley
e21757a057 OMAP3: clock: indicate that gpt12_fck and wdt1_fck are in the WKUP clockdomain
The oscillator that supplies GPT12_FCLK and WDT1_FCLK exists in the
WKUP powerdomain[1].  This resolves at least one boot-time warning:

omap_hwmod: gpt12_fck: missing clockdomain for gpt12_fck.

1. _OMAP34xx Multimedia High Security (HS) Device Silicon Revision 3.1.x
   Security Addendum Version K (SWPU119K)_  Figure 3-29.  August 2010.
2011-08-22 16:13:00 -06:00
Paul Walmsley
450a37d2ec OMAP4: clock: fix compile warning
Fix the following compile warning:

arch/arm/mach-omap2/clock44xx_data.c: In function 'omap4xxx_clk_init':
arch/arm/mach-omap2/clock44xx_data.c:3371:6: warning: 'cpu_clkflg' may be used uninitialized in this function

The approach taken here is intended to work if omap4xxx_clk_init() is
converted into an initcall.

Thanks to Bjarne Steinsbo <bsteinsbo@gmail.com> for proposing another
approach.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Bjarne Steinsbo <bsteinsbo@gmail.com>
2011-08-21 00:28:56 -06:00
Paul Walmsley
9c5f560173 OMAP4: clock: re-enable previous clockdomain enable/disable sequence
After commit 665d001338 ("OMAP2+: hwmod:
Follow the recommended PRCM module enable sequence"), device drivers
for OMAP IP blocks that do not use runtime PM can cause oopses or
kernel instability[1][2].

This is because those non-runtime PM drivers do not use the hwmod
code, which implements the correct IP block enable and disable
sequence.

Several options for dealing with this problem have been proposed:

1. Add a new field to the OMAP struct clk to mark clocks that are
   currently used by non-runtime PM drivers.  Modify the clock code to
   use the old clockdomain sequence for these marked clocks.  As
   drivers are converted to use runtime PM, remove the annotation from
   the clocks.

2. Similar to #1, but associate the flag with the struct omap_clk
   instead.

3. Add IDLEST wait support to the OMAP4 clock code, similar to the way
   it is implemented for OMAP2/3, and enable it in each struct clk
   currently used by non-runtime PM drivers.  As drivers are converted
   to use runtime PM, remove the annotation from the clocks.

4. Do nothing; leave the problem to those responsible for the
   unconverted drivers.

5. Re-enable clock-based clockdomain control in the OMAP4 clock code.
   This would revert back to the behavior of Linux 3.0, simply with a
   slightly longer module enable/disable latency.

Unfortunately, no approach seemed particularly good.  Options 1
through 3 seemed unwise due to the following reasons:

A. The OMAP struct clks are intended primarily to describe hardware
   clock nodes, and the intention is that no driver-specific data
   should be stored there (applies to #1)

B. The resulting patch would have been quite large for the -rc series
   (applies to #1, #2, #3)

C. The patch would have been a new, yet temporary hack; and similar fixes
   have drawn negative comments in the recent past (see for example [3])

Option 4 is undesirable because commit
665d001338 ("OMAP2+: hwmod: Follow the
recommended PRCM module enable sequence") has resulted in a less
stable kernel; and kernel stability is more important than OMAP4 power
management.

Option 5 is the approach taken in this patch.  This seemed to be the
least intrusive approach for 3.1-rc.

The approach in this patch was originally proposed by Ohad Ben-Cohen
<ohad@wizery.com>.  I'm simply writing the commit message and passing
it along.

...

Thanks to Luciano Coelho <coelho@ti.com> for reporting the problem.
Thanks to Ohad Ben-Cohen <ohad@wizery.com> for tracking the problem
down, generating a temporary workaround, and proposing a patch to deal
with the problem.  Thanks to Rajendra Nayak <rnayak@ti.com> for
proposing another patch to deal with the problem.  Thanks to Felipe
Balbi <balbi@ti.com> for comments.

1. Coelho, Luciano <coelho@ti.com>.  _Re: Oops on ehci_hcd when
   booting 3.0.0-rc2 on panda_.  Tue, 09 Aug 2011 14:26:08 +0300.
   Posted to the <linux-omap@vger.kernel.org> mailing list.  Available
   from (among others)
   http://www.spinics.net/linux/lists/linux-omap/msg55213.html

2. Munegowda, Keshava <keshava_mgowda@ti.com>. _Re: Oops on ehci_hcd
   when booting 3.0.0-rc2 on panda_.  Thu, 11 Aug 2011 13:51:05 +0530.
   Posted to the <linux-omap@vger.kernel.org> mailing list.  Available
   from (among others)
   http://www.spinics.net/linux/lists/linux-omap/msg55371.html

3. King, Russell <linux@arm.linux.org.uk>.  _Re: [PATCH 5/8] OMAP4:
   PM: TEMP: Prevent l3init from idling/force sleep_.  Thu, 23 Jun
   2011 16:22:49 +0100.  Posted to the <linux-omap@vger.kernel.org>
   mailing list.  Available from (among others)
   http://www.mail-archive.com/linux-omap@vger.kernel.org/msg51392.html

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Luciano Coelho <coelho@ti.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
2011-08-19 16:59:56 -06:00
Santosh Shilimkar
b1cbdb00da OMAP: clockdomain: Wait for powerdomain to be ON when using clockdomain force wakeup
While using clockdomain force wakeup method, not waiting for powerdomain
to be effectively ON may end up locking the clockdomain FSM until a
next wakeup event occurs.

One such issue was seen on OMAP4430, where L4_PER was periodically
getting stuck in in-transition state when transitioning from from OSWR to ON.

This issue was reported and investigated by Patrick Titiano <p-titiano@ti.com>

Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reported-by: Patrick Titiano <p-titiano@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: updated to apply; added transition wait on clkdm_deny_idle();
 remove two superfluous pwrdm_wait_transition() calls]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2011-08-19 16:59:39 -06:00
Rajendra Nayak
c956b753e7 OMAP: powerdomains: Make all powerdomain target states as ON at init
Program all powerdomain target state as ON; this is to prevent domains
from hitting low power states (if bootloader has target states set to
something other than ON) and potentially even losing context while PM
is not fully initialized, which can cause the system to crash.  The PM
late init code can then program the desired target state for all the
power domains.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[paul@pwsan.com: dropped comment typo hunk; fixed comment indent and moved
 to kerneldoc; moved code to pwrdm_init(); changed pwrdm_init() argument name
 to prevent clash; cleaned up patch description]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2011-08-19 16:59:39 -06:00
Hemant Pedanekar
e9d0b97eef omap: timer: Set dmtimer used as clocksource in autoreload mode
If CONFIG_OMAP_32K_TIMER is not selected and dmtimer is used as clocksource, the
timer stops counting once overflow occurs as it was not set in autoreload mode.
This results into timekeeping failure: for example, 'sleep 1' at the shell after
the timer counter overflow would hang.

This patch sets up autoreload when starting the clocksource timer which fixes
the above issue.

Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-08-10 07:36:45 -07:00
Johan Hovold
133e6b55b1 OMAP3: am3517crane: remove NULL board_mux from board file
Since 7203f8a48b (arm: mach-omap2: remove
NULL board_mux from board files) NULL board_mux is defined in mux.h.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-08-10 04:54:48 -07:00
Thomas Meyer
dccb3b0eb6 arm: mach-omap2: mux: use kstrdup()
Use kstrdup rather than duplicating its implementation

The semantic patch that makes this output is available
in scripts/coccinelle/api/kstrdup.cocci.

More information about semantic patching is available at
http://coccinelle.lip6.fr/

Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-08-10 04:53:28 -07:00
Tony Lindgren
58cf5e7fd5 Merge branch 'for_3.1/pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into fixes 2011-08-10 03:36:42 -07:00
Paul Walmsley
c9a48c2aac OMAP: hwmod: fix build break on non-OMAP4 multi-OMAP2 builds
Builds for multi-OMAP2 (e.g., OMAP2420 with OMAP2430) with
CONFIG_ARCH_OMAP4=n fail with the following errors:

arch/arm/mach-omap2/built-in.o: In function `_enable_module':
arch/arm/mach-omap2/omap_hwmod.c:701: undefined reference to `omap4_cminst_module_enable'
arch/arm/mach-omap2/built-in.o: In function `_disable_module':
arch/arm/mach-omap2/omap_hwmod.c:726: undefined reference to `omap4_cminst_module_disable'
arch/arm/mach-omap2/built-in.o: In function `_wait_target_disable':
arch/arm/mach-omap2/omap_hwmod.c:1179: undefined reference to `omap4_cminst_wait_module_idle'

This is probably due to the preprocessor directives in
arch/arm/plat-omap/include/plat/cpu.h that convert some cpu_is_omap*()
expressions from preprocessor directives into something that is only
resolvable during runtime, if multiple OMAP2 build targets are
selected.

Thanks to Tony Lindgren <tony@atomide.com> for reporting.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-08-10 02:20:43 -07:00
Peter Ujfalusi
d12d1fcafa OMAP: Fix linking error in twl-common.c for OMAP2/3/4 only builds
Commit b22f954 (OMAP4: Move common twl6030 configuration to twl-common)
caused compile failures for code for OMAP arch which is not selected by
the config.

Fixes issues like:
With CONFIG_ARCH_OMAP3=y and CONFIG_ARCH_OMAP4=n, I'm getting this:

arch/arm/mach-omap2/built-in.o:(.data+0xf99c): undefined reference to `omap4430_phy_init'
arch/arm/mach-omap2/built-in.o:(.data+0xf9a0): undefined reference to `omap4430_phy_exit'
arch/arm/mach-omap2/built-in.o:(.data+0xf9a4): undefined reference to `omap4430_phy_power'
arch/arm/mach-omap2/built-in.o:(.data+0xf9a8): undefined reference to `omap4430_phy_set_clk'
arch/arm/mach-omap2/built-in.o:(.data+0xf9ac): undefined reference to `omap4430_phy_suspend'

Fix the problem by moving the code to ifdef sections for omap3 and omap4.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-08-10 02:09:19 -07:00
Colin Cross
98333b3dda OMAP2+: PM: SmartReflex: use put_sync_suspend for IRQ-safe disabling
omap_sr_disable_reset_volt is called with irqs off in omapx_enter_sleep,
as part of idle sequence, this eventually calls sr_disable and
pm_runtime_put_sync. pm_runtime_put_sync calls rpm_idle, which will
enable interrupts in order to call the callback. In this short interval
when interrupts are enabled, scenarios such as the following can occur:
while interrupts are enabled, the timer interrupt that is supposed to
wake the device out of idle occurs and is acked, so when the CPU finally
goes to off, the timer is already gone, missing a wakeup event.

Further, as the documentation for runtime states:"
 However, subsystems can use the pm_runtime_irq_safe() helper function
 to tell the PM core that a device's ->runtime_suspend() and ->runtime_resume()
 callbacks should be invoked in atomic context with interrupts disabled
 (->runtime_idle() is still invoked the default way)."

Hence, replace pm_runtime_put_sync with pm_runtime_put_sync_suspend
to invoke the suspend handler and shut off the fclk for SmartReflex
module instead of using the idle handler in interrupt disabled context.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Colin Cross <ccross@google.com>
[khilman@ti.com: minor Subject edits]
Signed-off-by: Kevin Hilman <khilman@ti.com>
2011-08-05 11:54:59 -07:00
Kevin Hilman
8c7f65943d OMAP3: beagle: don't touch omap_device internals
Board code should not touch omap_device internals.  To get the MPU/IVA devices,
use existing APIs: omap2_get_mpu_device(), omap2_get_iva_device().

Signed-off-by: Kevin Hilman <khilman@ti.com>
2011-08-05 11:54:58 -07:00
Nishanth Menon
e13d8f3839 OMAP3+: SR: ensure pm-runtime callbacks can be invoked with IRQs disabled
SmartReflex should be disabled while entering low power mode due to
a) SmartReflex values are not defined for retention voltage, further
b) with SmartReflex enabled, if CPU enters lower c-states, FSM will try
to bump the voltage to current OPP's voltage for which it has entered c-state;
hence SmartReflex needs to be disabled for MPU, CORE and IVA voltage
domains in idle path before enabling auto retention voltage achievement
on the device.

However, since the current pm_runtime setup for SmartReflex devices are
setup to allow callbacks to be invoked with interrupts enabled, calling
SmartReflex enable/disable from other contexts such as idle paths
where preemption is disabled causes warnings such as the following
indicating of a potential race.
[   82.023895] [<c04d079c>] (__irq_svc+0x3c/0x120) from [<c04d0484>] (_raw_spin_unlock_irq+0x28/0x2c)
[   82.023895] [<c04d0484>] (_raw_spin_unlock_irq+0x28/0x2c) from [<c0323234>] (rpm_callback+0x4c/0x68)
[   82.023956] [<c0323234>] (rpm_callback+0x4c/0x68) from [<c0323f7c>] (rpm_resume+0x338/0x53c)
[   82.023956] [<c0323f7c>] (rpm_resume+0x338/0x53c) from [<c03243f4>] (__pm_runtime_resume+0x48/0x60)
[   82.023986] [<c03243f4>] (__pm_runtime_resume+0x48/0x60) from [<c008aee0>] (sr_enable+0xa8/0x19c)
[   82.023986] [<c008aee0>] (sr_enable+0xa8/0x19c) from [<c008b2fc>] (omap_sr_enable+0x50/0x90)
[   82.024017] [<c008b2fc>] (omap_sr_enable+0x50/0x90) from [<c00888c0>] (omap4_enter_sleep+0x138/0x168)

Instead, we use pm_runtime_irq_safe to tell the PM core that callbacks can be
invoked in interrupt disabled contexts.

Acked-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
[khilman@ti.com: minor changelog edits]
Signed-off-by: Kevin Hilman <khilman@ti.com>
2011-08-05 11:54:55 -07:00
Kevin Hilman
44e51b2922 OMAP2+: Kconfig: don't select PM in OMAP2PLUS_TYPICAL
CONFIG_PM is no longer a user-selectable Kconfig option.  Rather it is
automatically enabled if either CONFIG_SUSPEND or CONFIG_RUNTIME_PM is
enabled, so having a 'select PM' here is redunant when 'select
CONFIG_PM_RUNTIME' is present.

Signed-off-by: Kevin Hilman <khilman@ti.com>
2011-08-05 11:54:53 -07:00
Linus Torvalds
965e32b18d Merge branch 'for-3.1-rc1' of git://gitorious.org/linux-omap-dss2/linux
* 'for-3.1-rc1' of git://gitorious.org/linux-omap-dss2/linux: (31 commits)
  OMAP: DSS2: HDMI: fix hdmi clock name
  HACK: OMAP: DSS2: clk hack for OMAP2/3
  OMAP: DSS2: DSS: Fix context save/restore
  OMAP: DSS2: DISPC: Fix context save/restore
  OMAP: DSS2: Remove ctx loss count from dss.c
  OMAP: DSS2: Remove unused code from display.c
  OMAP: DSS2: DISPC: remove finegrained clk enables/disables
  OMAP: DSS2: Remove unused opt_clock_available
  OMAP: DSS2: Use PM runtime & HWMOD support
  OMAP: DSS2: Remove CONFIG_OMAP2_DSS_SLEEP_BEFORE_RESET
  OMAP: DSS2: Remove core_dump_clocks
  OMAP: DSS2: DPI: remove unneeded SYSCK enable/disable
  OMAP: DSS2: Use omap_pm_get_dev_context_loss_count to get ctx loss count
  OMAP: DSS2: rewrite use of context_loss_count
  OMAP: DSS2: Remove clk optimization at dss init
  OMAP: DSS2: Fix init and unit sequence
  OMAP: DSS2: Clean up probe for DSS & DSI
  OMAP: DSS2: Handle dpll4_m4_ck in dss_get/put_clocks
  OMAP: DSS2: Fix FIFO threshold and burst size for OMAP4
  OMAP: DSS2: DSI: sync when disabling a display
  ...
2011-08-01 06:13:05 -10:00
Linus Torvalds
664a41b8a9 Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (430 commits)
  [media] ir-mce_kbd-decoder: include module.h for its facilities
  [media] ov5642: include module.h for its facilities
  [media] em28xx: Fix DVB-C maxsize for em2884
  [media] tda18271c2dd: Fix saw filter configuration for DVB-C @6MHz
  [media] v4l: mt9v032: Fix Bayer pattern
  [media] V4L: mt9m111: rewrite set_pixfmt
  [media] V4L: mt9m111: fix missing return value check mt9m111_reg_clear
  [media] V4L: initial driver for ov5642 CMOS sensor
  [media] V4L: sh_mobile_ceu_camera: fix Oops when USERPTR mapping fails
  [media] V4L: soc-camera: remove soc-camera bus and devices on it
  [media] V4L: soc-camera: un-export the soc-camera bus
  [media] V4L: sh_mobile_csi2: switch away from using the soc-camera bus notifier
  [media] V4L: add media bus configuration subdev operations
  [media] V4L: soc-camera: group struct field initialisations together
  [media] V4L: soc-camera: remove now unused soc-camera specific PM hooks
  [media] V4L: pxa-camera: switch to using standard PM hooks
  [media] NetUP Dual DVB-T/C CI RF: force card hardware revision by module param
  [media] Don't OOPS if videobuf_dvb_get_frontend return NULL
  [media] NetUP Dual DVB-T/C CI RF: load firmware according card revision
  [media] omap3isp: Support configurable HS/VS polarities
  ...

Fix up conflicts:
 - arch/arm/mach-omap2/board-rx51-peripherals.c:
     cleanup regulator supply definitions in mach-omap2
   vs
     OMAP3: RX-51: define vdds_csib regulator supply
 - drivers/staging/tm6000/tm6000-alsa.c (trivial)
2011-07-30 00:08:53 -07:00
Kalle Jokiniemi
75ccf268d5 [media] OMAP3: RX-51: define vdds_csib regulator supply
The RX-51 uses the CSIb IO complex for camera operation. The
board file is missing definition for the regulator supplying
the CSIb complex, so this is added for better power
management.

Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:56:06 -03:00
Linus Torvalds
b0189cd087 Merge branch 'next/devel2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'next/devel2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (47 commits)
  OMAP: Add debugfs node to show the summary of all clocks
  OMAP2+: hwmod: Follow the recommended PRCM module enable sequence
  OMAP2+: clock: allow per-SoC clock init code to prevent clockdomain calls from clock code
  OMAP2+: clockdomain: Add per clkdm lock to prevent concurrent state programming
  OMAP2+: PM: idle clkdms only if already in idle
  OMAP2+: clockdomain: add clkdm_in_hwsup()
  OMAP2+: clockdomain: Add 2 APIs to control clockdomain from hwmod framework
  OMAP: clockdomain: Remove redundant call to pwrdm_wait_transition()
  OMAP4: hwmod: Introduce the module control in hwmod control
  OMAP4: cm: Add two new APIs for modulemode control
  OMAP4: hwmod data: Add modulemode entry in omap_hwmod structure
  OMAP4: hwmod data: Add PRM context register offset
  OMAP4: prm: Remove deprecated functions
  OMAP4: prm: Replace warm reset API with the offset based version
  OMAP4: hwmod: Replace RSTCTRL absolute address with offset macros
  OMAP: hwmod: Wait the idle status to be disabled
  OMAP4: hwmod: Replace CLKCTRL absolute address with offset macros
  OMAP2+: hwmod: Init clkdm field at boot time
  OMAP4: hwmod data: Add clock domain attribute
  OMAP4: clock data: Add missing divider selection for auxclks
  ...
2011-07-26 17:42:18 -07:00
Linus Torvalds
2d86a3f04e Merge branch 'next/board' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'next/board' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
  ARM: S3C64XX: Configure backup battery charger on Cragganmore
  ARM: S3C64XX: Fix WM8915 IRQ polarity on Cragganmore
  ARM: S3C64XX: Configure supplies for all Cragganmore regulators
  ARM: S3C64XX: Refresh Cragganmore support
  ARM: S3C64XX: Initial support for Wolfson/Simtec Cragganmore/Banff
  OMAP4: Keyboard: Mux changes in the board file
  omap: blaze: add mmc5/wl1283 device support
  omap: 4430SDP: Register the card detect GPIO properly
  arm: omap3: cm-t35: add support for cm-t3730
  OMAP3: beagle: add support for beagleboard xM revision C
  OMAP3: rx-51: Add full regulator definitions
  omap: rx51: Platform support for lp5523 led chip
2011-07-26 17:13:04 -07:00
Linus Torvalds
3960ef326a Merge branch 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
  ARM: Consolidate the clkdev header files
  ARM: set vga memory base at run-time
  ARM: convert PCI defines to variables
  ARM: pci: make pcibios_assign_all_busses use pci_has_flag
  ARM: remove unnecessary mach/hardware.h includes
  pci: move microblaze and powerpc pci flag functions into asm-generic
  powerpc: rename ppc_pci_*_flags to pci_*_flags

Fix up conflicts in arch/microblaze/include/asm/pci-bridge.h
2011-07-26 17:12:10 -07:00
Linus Torvalds
62c9072bee Merge branch 'next/fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'next/fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (24 commits)
  ASoC: omap: McBSP: fix build breakage on OMAP1
  OMAP: hwmod: fix the i2c-reset timeout during bootup
  I2C: OMAP2+: add correct functionality flags to all omap2plus i2c dev_attr
  I2C: OMAP2+: Tag all OMAP2+ hwmod defintions with I2C IP revision
  I2C: OMAP1/OMAP2+: create omap I2C functionality flags for each cpu_... test
  I2C: OMAP2+:  Introduce I2C IP versioning constants
  I2C: OMAP2+: increase omap_i2c_dev_attr flags from u8 to u32
  I2C: OMAP2+: Set hwmod flags to only allow 16-bit accesses to i2c
  OMAP4: hwmod data: Change DSS main_clk scheme
  OMAP4: powerdomain data: Remove unsupported MPU powerdomain state
  OMAP4: clock data: Keep GPMC clocks always enabled and hardware managed
  OMAP4: powerdomain data: Fix core mem states and missing cefuse flag
  OMAP2+: PM: Initialise sleep_switch to a non-valid value
  OMAP4: hwmod data: Modify DSS opt clocks
  OMAP4: iommu: fix clock name
  omap: iovmm: s/sg_dma_len(sg)/sg->length/
  omap: iommu: fix pte programming
  arm: omap3: cm-t35: fix slow path warning
  arm: omap3: cm-t35: minor comments fixes
  omap: ZOOM: QUART: Request reset GPIO
  ...
2011-07-26 17:10:20 -07:00
Linus Torvalds
4b30b6f23a Merge branch 'next/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'next/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
  MAINTAINERS: add maintainer of CSR SiRFprimaII machine
  ARM: CSR: initializing L2 cache
  ARM: CSR: mapping early DEBUG_LL uart
  ARM: CSR: Adding CSR SiRFprimaII board support
  OMAP4: clocks: Update the clock tree with 4460 clock nodes
  OMAP4: PRCM: OMAP4460 specific PRM and CM register bitshifts
  OMAP4: ID: add omap_has_feature for max freq supported
  OMAP: ID: introduce chip detection for OMAP4460
  ARM: Xilinx: merge board file into main platform code
  ARM: Xilinx: Adding Xilinx board support

Fix up conflicts in arch/arm/mach-omap2/cm-regbits-44xx.h
2011-07-26 17:09:31 -07:00
Linus Torvalds
f549953c15 Merge branch 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (115 commits)
  EHCI: fix direction handling for interrupt data toggles
  USB: serial: add IDs for WinChipHead USB->RS232 adapter
  USB: OHCI: fix another regression for NVIDIA controllers
  usb: gadget: m66592-udc: add pullup function
  usb: gadget: m66592-udc: add function for external controller
  usb: gadget: r8a66597-udc: add pullup function
  usb: renesas_usbhs: support multi driver
  usb: renesas_usbhs: inaccessible pipe is not an error
  usb: renesas_usbhs: care buff alignment when dma handler
  USB: PL2303: correctly handle baudrates above 115200
  usb: r8a66597-hcd: fixup USB_PORT_STAT_C_SUSPEND shift
  usb: renesas_usbhs: compile/config are rescued
  usb: renesas_usbhs: fixup comment-out
  usb: update email address in ohci-sh and r8a66597-hcd
  usb: r8a66597-hcd: add function for external controller
  EHCI: only power off port if over-current is active
  USB: mon: Allow to use usbmon without debugfs
  USB: EHCI: go back to using the system clock for QH unlinks
  ehci: add pci quirk for Ordissimo and RM Slate 100 too
  ehci: refactor pci quirk to use standard dmi_check_system method
  ...

Fix up trivial conflicts in Documentation/feature-removal-schedule.txt
2011-07-25 23:08:32 -07:00
Linus Torvalds
ae4c42e4e4 Merge branch 'next/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'next/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (133 commits)
  ARM: EXYNOS4: Change devname for FIMD clkdev
  ARM: S3C64XX: Cleanup mach/regs-fb.h from mach-s3c64xx
  ARM: S5PV210: Cleanup mach/regs-fb.h from mach-s5pv210
  ARM: S5PC100: Cleanup mach/regs-fb.h from mach-s5pc100
  ARM: S3C24XX: Use generic s3c_set_platdata for devices
  ARM: S3C64XX: Use generic s3c_set_platdata for OneNAND
  ARM: SAMSUNG: Use generic s3c_set_platdata for NAND
  ARM: SAMSUNG: Use generic s3c_set_platdata for USB OHCI
  ARM: SAMSUNG: Use generic s3c_set_platdata for HWMON
  ARM: SAMSUNG: Use generic s3c_set_platdata for FB
  ARM: SAMSUNG: Use generic s3c_set_platdata for TS
  ARM: S3C64XX: Add PWM backlight support on SMDK6410
  ARM: S5P64X0: Add PWM backlight support on SMDK6450
  ARM: S5P64X0: Add PWM backlight support on SMDK6440
  ARM: S5PC100: Add PWM backlight support on SMDKC100
  ARM: S5PV210: Add PWM backlight support on SMDKV210
  ARM: EXYNOS4: Add PWM backlight support on SMDKC210
  ARM: EXYNOS4: Add PWM backlight support on SMDKV310
  ARM: SAMSUNG: Create a common infrastructure for PWM backlight support
  clocksource: convert 32-bit down counting clocksource on S5PV210/S5P64X0
  ...

Fix up trivial conflict in arch/arm/mach-imx/mach-scb9328.c
2011-07-25 12:38:42 -07:00
Tomi Valkeinen
6d9f29dd62 OMAP: DSS2: Remove unused code from display.c
oh_core variable is no longer used, so it and its initialization can be
removed.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-07-25 10:22:06 +03:00
Tomi Valkeinen
aea4eb9590 OMAP: DSS2: Remove unused opt_clock_available
opt_clock_available() is no longer needed, so remove it.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-07-25 10:22:05 +03:00
Tomi Valkeinen
700dee78dc OMAP: DSS2: Use omap_pm_get_dev_context_loss_count to get ctx loss count
Initialize get_context_loss_count in the DSS board data to
omap_pm_get_dev_context_loss_count, so that omapdss driver can use it.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-07-25 10:08:15 +03:00
Tomi Valkeinen
aac927c93b OMAP: DSS2: rewrite use of context_loss_count
The function to get device's context loss count has changed from

omap_pm_get_last_off_on_transaction_id() to
omap_pm_get_dev_context_loss_count()

Change name of the function pointer in omapdss.h accordingly, and use
the term "context loss count" instead of "context id" in the code.

Restructure the context loss count functions to handle errors properly,
and ensure that context is always considered lost if an error happens.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-07-25 10:08:15 +03:00
Linus Torvalds
b6844e8f64 Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (237 commits)
  ARM: 7004/1: fix traps.h compile warnings
  ARM: 6998/2: kernel: use proper memory barriers for bitops
  ARM: 6997/1: ep93xx: increase NR_BANKS to 16 for support of 128MB RAM
  ARM: Fix build errors caused by adding generic macros
  ARM: CPU hotplug: ensure we migrate all IRQs off a downed CPU
  ARM: CPU hotplug: pass in proper affinity mask on IRQ migration
  ARM: GIC: avoid routing interrupts to offline CPUs
  ARM: CPU hotplug: fix abuse of irqdesc->node
  ARM: 6981/2: mmci: adjust calculation of f_min
  ARM: 7000/1: LPAE: Use long long printk format for displaying the pud
  ARM: 6999/1: head, zImage: Always Enter the kernel in ARM state
  ARM: btc: avoid invalidating the branch target cache on kernel TLB maintanence
  ARM: ARM_DMA_ZONE_SIZE is no more
  ARM: mach-shark: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ARM: mach-sa1100: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ARM: mach-realview: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ARM: mach-pxa: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ARM: mach-ixp4xx: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ARM: mach-h720x: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ARM: mach-davinci: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
  ...
2011-07-24 10:20:54 -07:00