The MPSC serial driver assumes that interrupt is always on to pick up the
DMA transmit ops that aren't submitted while the DMA engine is active.
However when irqs are off for a period of time such as operations under
kernel crash dump console messages do not show up due to additional DMA ops
are being dropped. This makes console writes to process through all the tx
DMAs queued up before submitting a new request.
Also, the current locking mechanism does not protect the hardware registers
and ring buffer when a printk is done during the serial write operations.
The additional per port transmit lock provides a finer granular locking and
protects registers being clobbered while printks are nested within UART
writes.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At present, the serial core always allows setserial in userspace to change the
port address, irq and base clock of any serial port. That makes sense for
legacy ISA ports, but not for (say) embedded ns16550 compatible serial ports
at peculiar addresses. In these cases, the kernel code configuring the ports
must know exactly where they are, and their clocking arrangements (which can
be unusual on embedded boards). It doesn't make sense for userspace to change
these settings.
Therefore, this patch defines a UPF_FIXED_PORT flag for the uart_port
structure. If this flag is set when the serial port is configured, any
attempts to alter the port's type, io address, irq or base clock with
setserial are ignored.
In addition this patch uses the new flag for on-chip serial ports probed in
arch/powerpc/kernel/legacy_serial.c, and for other hard-wired serial ports
probed by drivers/serial/of_serial.c.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the integrated serial ports of the MIPS RM9122 processor
and its relatives.
The patch also does some whitespace cleanup.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Serial driver patch for the PMC-Sierra MSP71xx devices.
There are three different fixes:
1 Fix for DesignWare APB THRE errata: In brief, this is a non-standard
16550 in that the THRE interrupt will not re-assert itself simply by
disabling and re-enabling the THRI bit in the IER, it is only re-enabled
if a character is actually sent out.
It appears that the "8250-uart-backup-timer.patch" in the "mm" tree
also fixes it so we have dropped our initial workaround. This patch now
needs to be applied on top of that "mm" patch.
2 Fix for Busy Detect on LCR write: The DesignWare APB UART has a feature
which causes a new Busy Detect interrupt to be generated if it's busy
when the LCR is written. This fix saves the value of the LCR and
rewrites it after clearing the interrupt.
3 Workaround for interrupt/data concurrency issue: The SoC needs to
ensure that writes that can cause interrupts to be cleared reach the UART
before returning from the ISR. This fix reads a non-destructive register
on the UART so the read transaction completion ensures the previously
queued write transaction has also completed.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PCI drivers have the new_id file in sysfs which allows new IDs to be added
at runtime. The advantage is to avoid re-compilation of a driver that
works for a new device, but it's ID table doesn't contain the new device.
This mechanism is only meant for testing, after the driver has been tested
successfully, the ID should be added in source code so that new revisions
of the kernel automatically detect the device.
The implementation follows the PCI implementation. The interface is documented
in Documentation/pcmcia/driver.txt. Computations should be done in userspace,
so the sysfs string contains the raw structure members for matching.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a minor correctness fix: since the at91_cf driver probe() routine
is in the init section, it should use platform_driver_probe() instead of
leaving that pointer around in the driver struct after init section
removal.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This introduce krealloc() that reallocates memory while keeping the contents
unchanged. The allocator avoids reallocation if the new size fits the
currently used cache. I also added a simple non-optimized version for
mm/slob.c for compatibility.
[akpm@linux-foundation.org: fix warnings]
Acked-by: Josef Sipek <jsipek@fsl.cs.sunysb.edu>
Acked-by: Matt Mackall <mpm@selenic.com>
Acked-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This was broken. It adds complexity, for no good reason. Rather than
separate __pa() and __pa_symbol(), we should deprecate __pa_symbol(),
and preferably __pa() too - and just use "virt_to_phys()" instead, which
is more readable and has nicer semantics.
However, right now, just undo the separation, and make __pa_symbol() be
the exact same as __pa(). That fixes the bugs this patch introduced,
and we can do the fairly obvious cleanups later.
Do the new __phys_addr() function (which is now the actual workhorse for
the unified __pa()/__pa_symbol()) as a real external function, that way
all the potential issues with compile/link-time optimizations of
constant symbol addresses go away, and we can also, if we choose to, add
more sanity-checking of the argument.
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ppc4xx_sgdma.c is #including asm/dma-mapping.h directly, which should
only ever be included via linux/dma-mapping.h. asm/dma-mapping.h
relies on an enum defined in linux/dma-mapping.h before its own
include. This fixes the problem.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Implement deep-sleep on MPC52xx.
SDRAM is put into self-refresh with help of SRAM code
(alternatives would be code in FLASH, I-cache).
Interrupt code must also not be in SDRAM, so put it
in I-cache.
MPC52xx core is static, so contents will remain intact even
with clocks turned off.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If the serial port gets shut down, then console output stalls. 9 out
of 10 kernel hackers agree, this is a bad thing.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Device type should be "soc" (as in lite5200.dts), compatible is
already set to "mpc5200".
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add fsl-i2c to mpc5200 i2c node in device tree, and enable FSL_SOC.
Tested to work with built-in eeprom on lite5200b.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is now a common function to generate the modalias string,
so use it. We just need to add the \n at the end.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Apparently other parts of the kernel need to know the
modalias internally (like the sysfs code in macintosh driver).
To avoid consistency issues, we export this code and use it
everywhere it's needed rather than repeat it ...
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes a couple of missing dependencies in
arch/powerpc/boot/Makefile. First, it ensures that the zlib.h header
is linked in before attempting to build gunzip_util.o, as it is,
building gunzip_util.o usually works, but not always depending on make
order.
Second, it makes the final images which are built using a dts
dependent on that dts, so the image will be correctly rebuilt if the
dts changes. This in turn requires fixing the definition of the dts
variable. CONFIG_DEVICE_TREE from Kconfig will have quotes around it,
which don't matter when passing the variable to a shell, but which
need to be removed when incorporating it into a filename for make's
use.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
32-bit powerpc uses a PTE_FMT macro to handle printk() formatting of
PTE entries (which can vary in type and size). Apparently there was a
good reason for it once, but with current compilers it's simpler just
to workaround the variation with a cast in the printk() itself
(there's only one use).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update the global cpu speed variable according to current cpufreq speed,
/proc/cpuinfo reports the actual speed.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Powermac G5 suspend to disk implementation. The code is platform
agnostic but only tested on powermac, no other 64-bit powerpc
machines.
Because nvidiafb still breaks suspend I have marked it EXPERIMENTAL on
powermac and because I can't test it and some lowlevel code will need
changes it is BROKEN on all other 64-bit platforms.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements save and restore hooks for IOMMUs and implements
it the DART iommu.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
for consistency with other Open Firmware interfaces (and Sparc).
This is just a straight replacement.
This leaves the compatibility define in place.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows "hotplugging" of CPUs on G5 machines. CPUs that are
disabled are put into an idle loop with the decrementer frequency set
to minimum. To wake them up again we kick them just like when bringing
them up. To stop those CPUs from messing with any global state we stop
them from entering the timer interrupt.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows the zImage target to once again be used to build
all supported image types, rather than requiring an explicit
"make uImage" to avoid failing to create an unneeded cuImage.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a new function named smp_call_function_single(). This matches a generic
prototype from include/linux/smp.h.
Add a function smp_call_function_map(). This is, for the most part, a rename
of smp_call_function, with some added cpumask support. smp_call_function and
smp_call_function_single call into smp_call_function_map.
Lightly tested on 970mp (blade), power4 and power5.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the powerpc version of topology_init() from an __initcall to
a subsys_initcall to match all other architectures.
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds mpic to the system devices and implements suspend
and resume for them. This is necessary to get interrupts for
modules back to where they were before a suspend to disk.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a couple of kexec problems related to 64K page
support in the kernel. kexec issues a tlbie for each pte. The
parameters for the tlbie are the page size and the virtual address.
Support was missing for the computation of these two parameters
for 64K pages. This adds that support.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The RF kill patch that provides infrastructure for implementing
switches controlling radio states on various network and other cards.
[dtor@insightbb.com: address review comments]
[akpm@linux-foundation.org: cleanups, build fixes]
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon failure to register "ptype" procfs entry, "softnet_stat" was not
removed, and an incorrect attempt was made to remove the "ptype" entry.
Signed-off-by: Josef 'Jeff' Sipek <jsipek@cs.sunysb.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spurious interrupts are often encountered especially on systems
using the 8259 PIC mode. This is because the I/O write to deassert
the interrupt is posted and won't get to the chip immediately. As
a result, the IRQ may remain asserted after the IRQ handler exits,
causing spurious interrupts.
Flush the interrupt mailbox in non-MSI handlers to de-assert the
IRQ immediately. This seems to be the most straight forward approach
after discussion with Jeff Garzik and David Miller.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds workaround to fix performance problems caused by slow
PCIE L1->L0 transitions on ICH8 platforms.
Changed all magic numbers to constants as suggested by Jeff Garzik.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark sunsu_console_setup() as __init and rename 'sunsu_cons'
to 'sunsu_console' so that it matches modpost.c's whitelist.
Signed-off-by: David S. Miller <davem@davemloft.net>
apb_calc_first_last(), apb_fake_ranges(), pci_of_scan_bus(),
of_scan_pci_bridge(), pci_of_scan_bus(), and pci_scan_one_pbm()
should all be __devinit.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some minor refactoring in the generic code was necessary for
this:
1) This controller requires 8-byte access to the interrupt map
and clear register. They are 64-bits on all the other
SBUS and PCI controllers anyways, so this was easy to cure.
2) The IMAP register has a different layout and some bits that we
need to preserve, so use a read/modify/write when making
changes to the IMAP register in generic code.
3) Flushing the entire IOMMU TLB is best done with a single write
to a register on this PCI controller, add a iommu->iommu_flushinv
for this.
Still lacks MSI support, that will come later.
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the IP-over-InfiniBand network device driver over to using
NAPI to handle completions for the main CQ. This covers all receives
as well as datagram mode sends; send completions for connected mode
connections are still handled from interrupt context.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The semantics defined by the InfiniBand specification say that
completion events are only generated when a completions is added to a
completion queue (CQ) after completion notification is requested. In
other words, this means that the following race is possible:
while (CQ is not empty)
ib_poll_cq(CQ);
// new completion is added after while loop is exited
ib_req_notify_cq(CQ);
// no event is generated for the existing completion
To close this race, the IB spec recommends doing another poll of the
CQ after requesting notification.
However, it is not always possible to arrange code this way (for
example, we have found that NAPI for IPoIB cannot poll after
requesting notification). Also, some hardware (eg Mellanox HCAs)
actually will generate an event for completions added before the call
to ib_req_notify_cq() -- which is allowed by the spec, since there's
no way for any upper-layer consumer to know exactly when a completion
was really added -- so the extra poll of the CQ is just a waste.
Motivated by this, we add a new flag "IB_CQ_REPORT_MISSED_EVENTS" for
ib_req_notify_cq() so that it can return a hint about whether the a
completion may have been added before the request for notification.
The return value of ib_req_notify_cq() is extended so:
< 0 means an error occurred while requesting notification
== 0 means notification was requested successfully, and if
IB_CQ_REPORT_MISSED_EVENTS was passed in, then no
events were missed and it is safe to wait for another
event.
> 0 is only returned if IB_CQ_REPORT_MISSED_EVENTS was
passed in. It means that the consumer must poll the
CQ again to make sure it is empty to avoid the race
described above.
We add a flag to enable this behavior rather than turning it on
unconditionally, because checking for missed events may incur
significant overhead for some low-level drivers, and consumers that
don't care about the results of this test shouldn't be forced to pay
for the test.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a num_comp_vectors member to struct ib_device and extend
ib_create_cq() to pass in a comp_vector parameter -- this parallels
the userspace libibverbs API. Update all hardware drivers to set
num_comp_vectors to 1 and have all ULPs pass 0 for the comp_vector
value. Pass the value of num_comp_vectors to userspace rather than
hard-coding a value of 1.
We want multiple CQ event vector support (via MSI-X or similar for
adapters that can generate multiple interrupts), but it's not clear
how many vectors we want, or how we want to deal with policy issues
such as how to decide which vector to use or how to set up interrupt
affinity. This patch is useful for experimenting, since no core
changes will be necessary when updating a driver to support multiple
vectors, and we know that we want to make at least these changes
anyway.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a problem where simple ACKs can be sent ahead of RDMA read
responses thus implicitly NAKing the RDMA read.
Signed-off-by: Ralph Campbell <ralph.cambpell@qlogic.com>
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
