If a USERPTR address that is not aligned to page boundary is passed to the
videobuf_dma_contig_user_get() function, it saves a page aligned address to
the dma_handle. This is not correct. This issue is observed when using USERPTR
IO machism for buffer exchange.
Updates from last version:-
Adding offset for size calculation as per comment from Magnus Damm. This
ensures the last page is also included for checking if memory is
contiguous.
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are old bttv-driven Hauppauge WinTV series cards that have
their IR part at i2c addr 0x71, which doesn't get considered in the
new 2.6.31 i2c code.
From a 2.6.29 kernel:
lirc_i2c: chip 0x10005 found @ 0x71 (Hauppauge PVR150)
Minor cosmetic glitch, the card in question isn't actually a PVR-150, its:
03:06.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
Subsystem: Hauppauge computer works Inc. WinTV Series
Flags: bus master, medium devsel, latency 32, IRQ 19
Memory at f4ffe000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Kernel driver in use: bttv
Kernel modules: bttv
Device ID: 0x109e:0x036e, Sub-Device ID: 0x0070:0x13eb
This simply adds 0x71 to the list of addresses i2c_new_probed_device should
consider, which gets IR working on this card again.
Reported-by: Adam Williamson <awilliam@redhat.com>
Tested-by: Adam Williamson <awilliam@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This was found with a static checker and has not been tested, but it seems
pretty clear that the mutex_lock() was supposed to be mutex_unlock()
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes a small issue where modinfo says the parameter "trace" is always available, while
it only works if CONFIG_USB_PWC_DEBUG is enabled.
Signed-off-by: Andrea Odetti <mariofutire@googlemail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
saa7134: Add support for IR reciever on card LifeView FlyDVB Trio
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
[mchehab@redhat.com: CodingStyle fixes and ported upstream]
Tested-by: Petr Fiala <petr.fiala@gmail.com>
Signed-off-by: Lukas Karas <lukas.karas@centrum.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This device uses an i2c chip to retrieve the keycode from a RC5 remote.
Instead of just getting 6 bits, improve the routine to get 11 bits.
This means that the complete RC5 table for Hauppauge Grey IR can be used
with this device.
Unfortunately, it seems that this IR receiver is not capable of getting
the full 14 (or 13 bits) from the RC5 protocol.
At lest now, with the new code, it is possible to replace this IR table
by another RC5 table.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds the above APIs to the v4l2 core. This is based on version v1.2
of the RFC titled "V4L - Support for video timings at the input/output interface"
Following new ioctls are added:-
- VIDIOC_ENUM_DV_PRESETS
- VIDIOC_S_DV_PRESET
- VIDIOC_G_DV_PRESET
- VIDIOC_QUERY_DV_PRESET
- VIDIOC_S_DV_TIMINGS
- VIDIOC_G_DV_TIMINGS
Please refer to the RFC for the details. This code was tested using vpfe
capture driver on TI's DM365. Following is the test configuration used :-
Blu-Ray HD DVD source -> TVP7002 -> DM365 (VPFE) ->DDR
A draft version of the TVP7002 driver (currently being reviewed in the mailing
list) was used that supports V4L2_DV_1080I60 & V4L2_DV_720P60 presets.
A loopback video capture application was used for testing these APIs. This calls
following IOCTLS :-
- verify the new v4l2_input capabilities flag added
- Enumerate available presets using VIDIOC_ENUM_DV_PRESETS
- Set one of the supported preset using VIDIOC_S_DV_PRESET
- Get current preset using VIDIOC_G_DV_PRESET
- Detect current preset using VIDIOC_QUERY_DV_PRESET
- Using stub functions in tvp7002, verify VIDIOC_S_DV_TIMINGS
and VIDIOC_G_DV_TIMINGS ioctls are received at the sub device.
- Tested on 64bit platform by Hans Verkuil
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some drivers support multiple frameintervals (framerates), make gspca able to
enumerate them.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The video_device::minor field is used where it shouldn't, either to
- test for error conditions that can't happen anymore with the current
v4l-dvb core,
- store the value in a driver private field that isn't used anymore,
- check the video device type where video_device::vfl_type should be
used, or
- create the name of a kernel thread that should get a stable name.
Remove or fix those use cases.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that the video_device registration is tested using
video_is_registered(), drivers don't need to initialize the
video_device::minor field to -1 anymore.
Remove those unneeded assignments.
[mchehab.redhat.com: removed tm6000 changes as tm6000 is not ready yet for submission even on staging]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using the minor number in kernel log messages, use the device
node name as returned by the video_device_node_name() function. This
makes debug, informational and error messages easier to understand for
end users.
[mchehab.redhat.com: removed tm6000 changes as tm6000 is not ready yet for submission even on staging]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix all device drivers to use the video_drvdata function instead of
maintaining a local list of minor to private data mappings. Call
video_set_drvdata to register the driver private pointer when not
already done.
Where applicable, the local list of mappings is completely removed when
it becomes unused.
[mchehab.redhat.com: removed tm6000 changes as tm6000 is not ready yet for submission even on staging]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix all device drivers to use the video_is_registered function instead
of checking video_device::minor.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace the video_is_unregistered function by a video_is_registered
function. The V4L2_FL_UNREGISTERED flag is replaced by a
V4L2_FL_REGISTERED flag.
This change makes the video_is_registered function return coherent
results when called on an initialize but not yet registered video_device
instance. The function can now be used instead of checking
video_device::minor.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix all device drivers to use the new video_device_node_name function.
This also strips kernel log messages from the "/dev/" prefix, has the device
node location is a userspace policy decision unknown to the kernel.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Many drivers access the device number (video_device::v4l2_devnode::num)
in order to print the video device node name. Add and use a helper
function to retrieve the video_device node name.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (345 commits)
V4L/DVB (13542): ir-keytable: Allow dynamic table change
V4L/DVB (13541): atbm8830: replace 64-bit division and floating point usage
V4L/DVB (13540): ir-common: Cleanup get key evdev code
V4L/DVB (13539): ir-common: add __func__ for debug messages
V4L/DVB (13538): ir-common: Use a dynamic keycode table
V4L/DVB (13537): ir: Prepare the code for dynamic keycode table allocation
V4L/DVB (13536): em28xx: Use the full RC5 code on HVR-950 Remote Controller
V4L/DVB (13535): ir-common: Add a hauppauge new table with the complete RC5 code
V4L/DVB (13534): ir-common: Remove some unused fields/structs
V4L/DVB (13533): ir: use dynamic tables, instead of static ones
V4L/DVB (13532): ir-common: Add infrastructure to use a dynamic keycode table
V4L/DVB (13531): ir-common: rename the debug routine to allow exporting it
V4L/DVB (13458): go7007: subdev conversion
V4L/DVB (13457): s2250: subdev conversion
V4L/DVB (13456): s2250: Change module structure
V4L/DVB (13528): em28xx: add support for em2800 VC211A card
em28xx: don't reduce scale to half size for em2800
em28xx: don't load audio modules when AC97 is mis-detected
em28xx: em2800 chips support max width of 640
V4L/DVB (13523): dvb-bt8xx: fix compile warning
...
Fix up trivial conflicts due to spelling fixes from the trivial tree in
Documentation/video4linux/gspca.txt
drivers/media/video/cx18/cx18-mailbox.h
Currently, the IR table is initialized by calling ir_input_init(). However,
this function doesn't return any error code, nor has a function to be called
when de-initializing the IR's.
Change the return argment to integer and make sure that each driver will
handle the error code. Also adds a function to free any resources that may
be allocating there: ir_input_free().
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Modifies the IR table for HVR-950 to use the newer Hauppauge RC5 table,
and adds the RC5 address to the functions that get the scancode for this
device.
It is easy to add support for all other RC5 IR's on em2880 boards, but
the scancode table needs to be re-generated. So, keep using the old
7bits tables while we don't have all tables converted.
Also, the 7bits tables are still used on other drivers, so this small
patch needs to be ported to all drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds support to VC211A em2800 card. As this board doesn't have eeprom,
and uses a common set of i2c address, it has no way to add any
autodetection for it.
The patch were tested by me and by Raimundo on his board. Thanks to
those tests, several bugs related to em2800 support were corrected.
for producing the usbsnoop dump, used to get the gpio's and allowing me
to remotelly access his machine and to the needed tests.
Thanks-to: Raimundo Eduvirgnes de Oliveira <eduvirgens@yahoo.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since em2800 can't support 720x480 / 720x576, the driver used to reduce
the scale to half the size on those chips. As the proper fix were
applied, reducing the maximum horizontal resolution to 640, this hack
can be removed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With em2800 hardware, AC97 hardware can be detected even when it doesn't
exist. If, after probing for AC97, the driver won't find a companion
chip, simply prevents the load of the audio modules.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to hardware limitation, em2800 chips can't work at resolutions
higher than 640x576, since the URB packet size is not enough.
The effect is that the image looses packages and shows a distortion
along the vertical axes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This prepares the pms driver for the v4l1 -> v4l2 conversion.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bNrInPins and baSourceID fields are common among all entities (some
of use bSourceID but this is conceptually the same). Move those two
fields out of entity type-specific unions into the uvc_entity structure
top level.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't handle the first output terminal in a chain in a special way. Use
uvc_scan_chain_entity() like for all other entities, making the chain
scan code more generic.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bNrInPins field is an 8 bit integer, not a 16 bit integer.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All terminals and units are now added to a single linked list of
entities per chain. This makes terminals and units handling code more
generic.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These are additional fixes to enable proper pvrusb2 support of 16KB
sized FX2 firmware.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The device text description in pvrusb2-devattr.c get mapped into a V4L
API string field that is unfortunately shorter than I expected. No
sense fighting City Hall here - this change shortens the descriptions
to fit the limit.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This pvrusb2 change is in support of an existing feature used to help
identify and locate newer vendor supplied firmware. This change makes
the feature work for the newer larger firmware size.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
New FX2 firmware from Hauppauge is no longer 8KB in size - it's 16KB.
This is true for HVR-1950 and HVR-1900 devices. Without this change,
new pvrusb2 users with that hardware are unable to use the driver
(because the CD shipped with the hardware only has the 16KB firmware).
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
