This new part has the same feature set as previous parts with the addition
of MSI-X support.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add support for new LOM devices on the latest generation ICHx platforms.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable PCI device ID for a new combination of MAC and PHY already supported
in the driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Change TSO offloads to use a different context than VLAN insertion
and Tx checksumming. Hardware has separate registers internally for
storing these so use them.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
hardware was configured incorrectly which led all hints to be
sent to queue[0]'s DCA configuration.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
DCA related fixes
=================
- ixgbe was not compiling and using DCA correctly if dca was a module
- DCA interface changed with new kernel
- ixgbe was not correctly configured to indicate DCA hints to the
correct CPU.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
as mentioned by Herbert, our hardware supports IP offloads, not full
checksum offloads for any protocol in existence (even though the
hardware just provides generic csum support over any range of bytes)
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This locks the seed down so loading/unloading the driver will present
predictable hashing from RSS. Also move the rx_buf_len out of the adapter
struct, and into the Rx ring struct.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable Tx Head Writeback in the hardware. This helps performance by
removing adapter writebacks to descriptors on transmit completion.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Since the adapter cannot tell what the remote end's flow control capability
is through auto-neg, we must turn off flow control by default.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cleanup all the different references to the Tx ring and Rx ring structures
and make them common across the driver.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Implement HAVE_SET_RX_MODE in the driver for MC and UC lists.
Signed-off-by: Christopher Leech <christopher.leech@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
the driver was misinterpreting rx_csum return value in the descriptor
so occassionally we would indicate an rx_csum error in our stats
when there was none. This would have no effect on traffic because
we would just hand the packet to the stack anyway without the offload
flag set, but would increase CPU for those packets that needed a recompute.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix hp-plus Makefile object file:
drivers/built-in.o: In function `hpp_open':
hp-plus.c:(.text+0xaf445): undefined reference to `ei_interrupt'
hp-plus.c:(.text+0xaf4ac): undefined reference to `ei_open'
drivers/built-in.o: In function `hpp_close':
hp-plus.c:(.text+0xaf59d): undefined reference to `ei_close'
drivers/built-in.o: In function `hpp_probe1':
hp-plus.c:(.init.text+0x7314): undefined reference to `ei_poll'
drivers/built-in.o: In function `hp_plus_probe':
(.init.text+0x7407): undefined reference to `__alloc_ei_netdev'
make[1]: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Resending since I didn't see any responses from the first try.
Change __constant_htons() to htons() in the bonding driver, it should
only be used for initializers.
-Brian
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When !port_enabled, defer the write to reconfigure_mac_wrapper.
Whilst here, simplify the logic now that efx_start_port() always calls
efx_reconfigure_port().
From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This was originally a kludge to fix broken locking, which has since
been fixed properly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Include PMA/PMD in loopback self-tests as intended.
Add NVRAM checksum validation and include it in self-tests.
Add register self-tests.
Run PHY self-tests where available.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This will support register self-tests.
From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Move more code from efx_reset() into efx_reset_down() and efx_reset_up().
Stop propagating MAC/PHY setting failures from efx_reset_down() and
efx_reset_up() as these should not be fatal.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some functions return an error code which is always 0. Change their
return types to void and simplify their callers accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Update comment on the dummy operation implementations.
Line up the board operation initialisers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This allows updating PHY firmware for one interface without removing
all other interfaces handled by the driver.
Replace tx_disabled flags and 10Xpress status enumeration with flags in
enum efx_phy_mode.
Prevent an interface from being brought up while in PHY flash mode.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make efx_process_channel() and falcon_process_eventq() return the
number of packets received rather than updating the quota, consistent
with new NAPI.
Since channels and RX queues are mapped one-to-one, remove return
value from falcon_handle_rx_event() and add a warning for events
with the wrong RX queue number.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently each channel can have at most one RX queue, so go straight to
that one.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We have long since given up doing RSS on Falcon A1 and therefore we
would always write the default value of 0.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rename efx_nic::rss_queues to the more obvious n_rx_queues
Remove efx_rx_queue::used and other stuff that's redundant with it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
efx_channel::has_interrupt is redundant with efx_channel::used_flags.
Remove efx_test_eventq() because it is now obviously unreachable.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Extend the SPI device setup code to support this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
gcc will automatically inline static functions with only one caller, and
may inline other functions depending on the kernel configuration and size
of the intermediate code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Squashed nested structures.
Renamed remaining_len to out_len, ifc.len to in_len, header_length to
header_len.
Moved ipv4_id into the group of output variables where it belongs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Replace (cond ? 1 : 0) with cond or !!cond as appropriate, and
(cond ? 0 : 1) with !cond.
Remove some redundant boolean temporaries.
Rename one field that looks like a flag but isn't.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove unmap_addr since it can be calculated from dma_addr, len and
unmap_len. This saves 4-16 bytes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add efx_poll_loopback() function to test for successful completion of test.
Change efx_test_loopback() to end the test after 1 ms if
efx_poll_loopback() indicates success, and otherwise to wait for 100 ms
as before.
While we're here, rename efx_{rx,tx}_loopback() to
efx_{begin,end}_loopback() which more accurately reflect their
purpose.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Removed log messages that are redundant with calling functions.
Fixed bitwise or-ing of return codes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This was making noise during 10Xpress self-test.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
These were clearly bogus.
From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Exclude assumed size of RX control frames from rx_bad_bytes.
Exclude assumed size of TX control frames from tx_good_bytes for
consistency with rx_good_bytes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We believed that some valid SNAP frames were being marked as invalid.
In fact this is not the case and no workaround is needed.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently the board initialisation includes 2 delays of 1 second each.
Usually it is unnecessary to wait that long, so check before doing so.
Correct some of the comments and log messages while we're here.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
efx_test_loopback() used "|" to combine the results of the RX and TX
phases. If both phases fail with different error codes, this results
in a bogus error code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Checksum generation is an attribute of our hardware TX queues, not TX
descriptors. We previously used a single queue and turned checksum
generation on or off as requested through ethtool. However, this can
result in regenerating checksums in raw packets that should not be
modified. We now create 2 hardware TX queues with checksum generation
on or off. They are presented to the net core as one queue since it
does not know how to select between them.
The self-test verifies that a bad checksum is unaltered on the queue
with checksum generation off.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This means the compiler doesn't need to use real division instructions.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use of the net_device::priv field is deprecated.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch rewrites the TX power recalculation algorithms to scale better
with changed enviromnent. If there's low
TX traffic, the power will be checked against the desired values
every 60 seconds.
If there is high TX traffic, the check is redone every 2 seconds. This improves
the reaction times a lot and confuses the rate control less.
It will also reduce the time it initially takes to tune to a new TX power
value. With the old algorithm it could take about 30 to 45 seconds to settle to
a new power value. This will happen in about two to four seconds now.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements a dynamic "ops" based PHY API.
This is needed in order to conveniently support future PHY types
to avoid the "switch"-hell.
This patch does not change any functionality. It just moves lots
of code from one place to another and adjusts it for the changed
data structures.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure the skb->data pointer points to the frame data, not the TX
descriptor. The frame dumping code relies on that.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using the PLCP flag to indicate if the
signal value is plcp or the bitrate we should add
a new flag to mark the bitrate type explicitely.
This is usefull when new types are added later for
rt2800.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The txop parameter is supported by rt61pci and rt73usb,
and thus should be written to the register instead
of using the fixed value set during initialization.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware configuration registers such as antenna and channel configuration
can only be written when the radio is enabled. Previously, we didn't consider
this, so some configuration items could be set inconsistently after reenabling
the radio. This patch changes the config() handler to only reprogram the
hardware when the radio is enabled. Configuration changes that are made while
the radio is off are postponed until the radio is switched back on. We also
leave the radio turned off during initialization and only enable it when
requested by mac80211. This allows us to get rid of the DIRTY_CONFIG flag,
because the device is now guaranteed to be completely initialized when brought
up by mac80211.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a driver requests additional headroom it should
be mapped to DMA as well because it will be send to
the hardware as well (as form of extra descriptor).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of the flags should be accessed atomically to
prevent race conditions. The flags that are most important
are those that can change often and indicate the actual
state of the device, queue or queue entry.
The big flag rename was done to move all state flags to
the same naming type as the other rt2x00dev flags and
made sure all places where the flags were used were changed. ;)
Thanks to Stephen for most of the queue flags updates,
which fixes some of the most obvious consequences of the
race conditions. Among those the notorious:
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use kernel doc syntax for comments and remove a few unused macros.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When AR_DurUpdateEna is set, the frame's duration field
is updated by the MAC based on the current rate.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves the all of p54pci's receiver code out of the
bloated interrupt handler routine and into a less critical tasklet.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware supports 8 different queues and not only 4.
So, let's make some room for further tasks (ap/adhoc support)
in this area.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
p54_rx_frame_sent will alter the tx_queue. Therefore we should hold
the lock to protect against concurrent p54_assign_address calls.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ever wondered why the signal was so bad with p54 compared to madwifi, or intel?
Well, if you have revision 1 rssi calibration curve points in your EEPROM, then wonder no more.
The firmware wants a extra 1 byte padding for every curve point. But someone forgot to put
them into the EEPROM's data structure...
So now, big question: what happens when we blindly "memcpy" these data points?
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver(s) below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/net/wireless/b43legacy/main.c
drivers/net/wireless/iwlwifi/iwl-3945-led.c
drivers/net/wireless/iwlwifi/iwl-led.c
drivers/net/wireless/iwlwifi/iwl-rfkill.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace the internal ath9k implementation of multicast/broadcast frame
power save buffering (AP mode) in ath9k with use of mac80211
ieee80211_get_buffered_bc() mechanism. This removes quite a bit of
duplicated functionality and simplifies the driver part.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set some semi-random values for HT and add more queues to allow IEEE
802.11n association to be tested with mac80211_hwsim. This with the
latest hostapd git tree version can complete a simulated 802.11n
association successfully (with mac80211 client MLME).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and return errors for operations like join & scan that aren't possible
when the radio is turned off.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and remove DISASSOCIATE because it's not in any of the specs and has
never been used.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And while we're at it, grab min/max TX power from the firmware and use
that to validate incoming TX power requests from WEXT.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't trim the FCS before passing the frame to mac80211,
move TSF_TO_TU to core.h and delete more unused macros.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, Max RX-ampdu and mpdu-density are ath9k specific.
Rename appropriately.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes ath_vap_listen() and dma wrapper macros.
Also, Inline abuse is cleaned up and a few typos are fixed.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use direct pci functions instead.
Also, use sc_ht_info.tx_chan_width directly and remove ath_cwm_macmode.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use TX control flag IEEE80211_TX_CTL_ASSIGN_SEQ as a request to update
the seq# for the frames. This will likely require some further cleanup
to get seq# correctly for Beacons vs. other frames and also potentially
for multiple BSSes. Anyway, this is better than ending up sending out
most frames with seq# 0.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change moves ath9k to use mac80211-generated Beacon frames instead
of trying to allocate a single Beacon frame and then update it. In
addition, the remaining ath_skb_{map,unmap}_single() wrapper calls are
replaced with direct pci_{map,unmap}_single() calls in beacon.c. Power
save buffering for multicast/broadcast frames is not yet converted to
use mac80211-style (frames to be buffered inside mac80211, not in
driver).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add sc_rxflush and sc_noreset as bitfields to sc_flags.
Remove a few variables and function prototypes that are unused.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ah_opmode and sc_opmode are redundant.
This patch removes sc_opmode.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
