Now we are extracting out methods for shutdown and the like we can add a
proper tty_port_close method that knows all the innards of the tty closing
process and hides the lot from the caller.
At some point in the future this will be paired with a similar open()
helper and the drivers can stick to hardware management.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A platform clock drives 8250 ports in most SOC systems, the clock
might run at high frequencies, and so it's not always possible to
downscale uart clock to a desired value.
Currently the 8250 uart driver accepts not supported baud rates, and
what is worse, it is doing this silently, and then passes not accepted
values to a new termios, so userspace has no chance to catch this kind
of errors (userspace verifies that settings were accepted by reading
back and comparing the settings).
This patch fixes the issue by passing minimum baud rate to the
uart_get_baud_rate() call, the call should take care of all bounds,
so userspace should now report:
# stty -F /dev/ttyS0 speed 300
115200
stty: /dev/ttyS0: unable to perform all requested operations
p.s. uart_get_baud_rate() falls back to 9600, which still might be too
low for some 10 GHz platforms, but that's a separate issue, and
we can wait with fixing this till we find such a platform.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is currently no provision for passing IRQ trigger flags for
serial IRQs with triggering requirements (such as GPIO IRQs)
This patch adds irqflags to plat_serial8250_port that can be passed
from board file to reqest_irq() of 8250 driver
Changes are backward compatible with boards passing UPF_SHARE_IRQ flag
Tested on Zoom2 board that has IRQF_TRIGGER_RISING requirement for 8250 irq
[Moved new flag to end to fix bugs in the original with the old_serial array
-- Alan]
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The modem ioctls are not routed via the ioctl method so kill the old dead
code. The correct code is also already present and hooked in.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I made a correction for get_lsr_info, now it returns some meaningful
information. I tested it with two simultaneous simplex modem channels.
it is attached
Signed-off-by: Kees Schoenmakers <k.schoenmakers@sigmae.nl>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the tiocmget/mset handling on the mos7720 USB serial port.
[Minor space reformatting for coding style - Alan]
Signed-off-by: Kees Schoenmakers <k.schoenmakers@sigmae.nl>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently kfifo cannot be used by parts of the kernel that use "const"
properly as kfifo itself does not use const for passed data blocks which
are indeed const.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The network layer now has a destructor we can hook to clean up the slip
devices array. That needs us to initiate unregister events in the right
places which with the current tty layer we can do, and with network
refcounting is safe to do.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove duplicated code from cy_set_line_char. There were 2 if
branches with same contents except flags.
Branch only for the flags computation and use them in the only copy
of the code.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add helpers for io operations, so that we can eliminate huge
amount of supporting code. It is now centralized in those
helpers and used values are precomputed in the init phase.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- save one indent level by inverting !fw_loaded condition
- read rs_status on Z and write it after we change all the flags,
don't do that separately
- remove Y inverted rts/dtr branching, precompute registers and use
them
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- add a cy_ prefix to functions with changed prototypes
- cy_get_serial_info: initialize serial_struct by initializer,
save a memset
- inline simple functions (get_mon_info, {s,g}et_default_threshold,
{s,g}et_default_timeout) directly in the ioctl handler
- add a cy_cflags_changed helper to not copy its code by
wait_event_interruptible
- remove some ret_val = 0 assignments, it's preset to 0
- TIOCGICOUNT: don't do many put_user's, do one copy_to_user
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a duplicated code for Y and Z in cy_startup, merge the paths.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For Z cards, use tty helpers for dtr_rts.
If we did the same for Y cards, it will cause a deadlock, because
cyy_dtr_rts takes a lock which we already hold.
Instead, we introduce a Y helper expecting card lock to be held.
It may then be called with set/clear masks from other places.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Avoid long busy loops (5 ms) which may be replaced by sleeps.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- remove changelog from the file. we don't care about ancient
history
- update copyright year
- update version
- constify some stuff
- empty lines removal
- unused variables and macros removal
- remove some asm/ includes, they are sucked by linux/ variants
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use new tty helpers for close, which allows much code removal.
The only real change is locking. card_lock for protecting was
used inappropriately (just to have a critical section, no matter
which lock is used), so the change to port->lock is fine.
Remove also useless debug printks while being there.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Do not duplicate common tty_port_hangup code. Use it instead.
Also do not unset ASYNC_NORMAL_ACTIVE and wake up from the
tty_hangup() caller. It makes no sense since we don't check that
flag in sleepers. tty_port_hangup() performed later will do the
right job.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't fetch firmware address and recompute channel control on each
port access. Precompute the values on init and use them later all
the time.
The same for board control.
This simplify code and improves readability.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use a tty_port common instead. This saves lots of .text and makes the
code a lot more readable.
This involves separation of a dtr_rts handling, next patches will use
that to not duplicate the code all over the place.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While this is not problem for Y card handlers (they are protected
by card_lock), Z handlers and other functions may dereference NULL
at any point after hangup/close. Even if (tty == NULL) was already
performed in the handler.
Note that it's not an issue for Y cards just for now. After
switching to tty_port_close_* et al. this will be a problem. So
add refcounting to them all.
Also proc .show doesn't take a tty reference and it should (along
with a ldisc one).
While at it and changing prototypes (adding tty param), prepend
cy_ to functions which don't have it yet.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Previously, if any bit other than CMD_SND_BREAK was set, CMD_SND_BREAK
was not unset.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fix the following 'make includecheck' warning:
drivers/char/vt.c: linux/device.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that the /proc/tty/ldiscs handling doesn't play games with 'struct
ldisc' any more, the only remaining user of 'tty_ldisc_try_get()' is
'tty_ldisc_get()' (note the lack of 'try').
And we're actually much better off folding the logic directly into that
file, since the 'try' part was always about trying to get the ldisc
operations, not the ldisc itself: and making that explicit inside of
'tty_ldisc_get()' clarifies the whole semantics.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>,
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@mail.by>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The /proc/tty/ldiscs file is totally and utterly un-interested in the
"struct tty_ldisc" structures, and only cares about the underlying ldisc
operations.
So don't make it create a dummy 'struct ldisc' only to get a pointer to
the operations, and then destroy it. Instead, we split up the function
'tty_ldisc_try_get()', and create a 'get_ldops()' helper that just looks
up the ldisc operations based on the ldisc number.
That makes the code simpler to read (smaller and more well-defined
helper functions), and allows the /proc functions to avoid creating that
useless dummy only to immediately free it again.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@mail.by>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since early printk only makes sense/works when the serial driver is built
into the kernel, disable the option for this driver when it is going to be
built as a module. Otherwise we get build failures due to the ifdef
handling.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The tty_operation chars_in_buffer() is not allowed to return a negative
value to signal an error. Corrects the problem flagged by commit
23198fda71, "tty: fix chars_in_buffers".
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This allows subsytems to provide devtmpfs with non-default permissions
for the device node. Instead of the default mode of 0600, null, zero,
random, urandom, full, tty, ptmx now have a mode of 0666, which allows
non-privileged processes to access standard device nodes in case no
other userspace process applies the expected permissions.
This also fixes a wrong assignment in pktcdvd and a checkpatch.pl complain.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After close looking, commit 8126dec3 will break:
1. some cpu feature in early stage too, like cpu_has_x2apic
2. will break built-in-command line
3. will break other memmap= and mem=
4. early_dbgp and early_console that will use early_ioremap to access mmio (?)
So revert it.
Reported-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>,
Cc: Linus Torvalds <torvalds@linux-foundation.org>,
Cc: Andrew Morton <akpm@linux-foundation.org>,
LKML-Reference: <4AB51DFD.2000904@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix following compile warning:
arch/x86/kernel/cpu/mcheck/mce_amd.c: In function 'threshold_create_bank':
arch/x86/kernel/cpu/mcheck/mce_amd.c:492: warning: unused variable 'c'
which shows up when kernel is compiled with CONFIG_SMP=n.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
LKML-Reference: <20090915151727.GB21670@alberich.amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There is still some weird code in per_copy_attr(). Which supposedly
checks that all bytes trailing a struct are zero.
It doesn't seem to get pointer arithmetic right. Since it
increments an iterating pointer by sizeof(unsigned long) rather
than 1.
Signed-off-by: Ian Schram <ischram@telenet.be>
[ v2: clean up the messy PTR_ALIGN logic as well. ]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: <stable@kernel.org> # for v2.6.31.x
LKML-Reference: <4AB3DEE2.3030600@telenet.be>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As per Ingo's review: use a #define rather than an open coded constant
for the maximum length of a trace event for storing in the perf.data file.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: fweisbec@gmail.com
Cc: peterz@infradead.org
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <20090919133630.10533d3e@infradead.org>
[ add a few comments to nearby functions ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As suggested by Ingo, add a timechart man page help text, as well
as add it to the "perf help" overview.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: fweisbec@gmail.com
Cc: peterz@infradead.org
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <20090919133604.3767fa35@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The "end of a C state" trace point currently happens before
the code runs that corrects the TSC for having stopped during idle.
The result of this is that the timestamp of the end-of-C-state event
is garbage on cpus where the TSC stops during idle.
This patch moves the end point of the C state to after the timekeeping
engine of the kernel has been corrected.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: fweisbec@gmail.com
Cc: peterz@infradead.org
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <20090919133533.139c2a46@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Be more consistent in the svghelper about the minimum text size
by having a global #define for this.
There needs to be a minimum text size in order to keep the size
of the SVG file within the reach of what current SVG viewers can
cope with.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: fweisbec@gmail.com
Cc: peterz@infradead.org
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arjan van de Ven <arjan@infradead.org>
LKML-Reference: <20090919133507.7374ef8b@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a command line option to record a trace, similar to "perf sched record".
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: fweisbec@gmail.com
Cc: peterz@infradead.org
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <20090919133442.0dc2c7f5@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Limit the length of a tracer's name within 100 chars, and then we
don't have to play with max_tracer_type_len.
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <4AB32377.9020601@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
No need to store ftrace_graph_funcs in file->private.
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <4AB32364.7020602@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
While doing some testing, I pinned mplayer, only to find it
following X around like a puppy. Looking at commit c88d591, I found
a cpu_allowed check that went AWOL. I plugged it back in where it
looks like it needs to go, and now when I say "sit, stay!", mplayer
obeys again.
'c88d591 sched: Merge select_task_rq_fair() and
sched_balance_self()' accidentally dropped the check, causing
wake_affine() to pull pinned tasks - put it back.
[ v2: use a cheaper version from Peter ]
Signed-off-by: Mike Galbraith <efault@gmx.de>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
timechart is a tool to visualize what is going on in the system.
The user makes a trace of what is going on with
> perf record --timechart /usr/bin/some_command
and then can turn the output of this into an svg file
> perf timechart
which then can be viewed with any SVG view; inkscape works well
enough for me.
The idea behind timechart is to create a "infinitely zoomable"
picture; something that has high level information on a 1:1 zoom
level, but which exposes more details every time you zoom into a
specific area.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20090912130713.6a77bbc0@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The timechart tool writes out SVG format output; this patch adds a
set of helper functions to abstract dealing with SVG from the core
timechart code.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20090912130613.677f0516@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch converts the existing power tracer into an event tracer,
so that power events (C states and frequency changes) can be
tracked via "perf".
This also removes the perl script that was used to demo the tracer;
its functionality is being replaced entirely with timechart.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20090912130542.6d314860@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a sample_event type to the event_union so that raw samples can
be processed easily.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20090912130511.411434b5@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
timechart needs to add a "callback" type command line argument that
does not take arguments.
This patch adds the parse-options.h infrastructure to make this
possible.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20090912130440.548666c1@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The trace event name<->id mapping is dynamic for each kernel
compile. In order for perf.data to be useable outside the actual
system, we thus need to store a table of this mapping for later
use.
This patch adds this table to perf.data, and provides helper
functions for lookup up fields from this table.
To avoid mistakes, lookup-from-table is kept completely seprate
from lookup-from-local-debugfs.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20090912130405.6960d099@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
