Commit f62349ee97 makes it possible to
have some other than first uart port as ttyS0, which breaks the workaround
serial_in_override() function which will try to address the first uart
port (for ttyS0) and not the one that was initialized.
Signed-off-by: Alexander Shishkin <virtuoso@slind.org>
CC: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 9905a43b made struct backlight_ops const. Omap was
setting check_fb dynamically, which caused the following
compile error:
drivers/video/backlight/omap1_bl.c: In function 'omapbl_probe':
drivers/video/backlight/omap1_bl.c:142: error: assignment of read-only variable 'omapbl_ops'
Turns out pdata->check_fb is not being used, so just remove
it to fix the compile.
Cc: Emese Revfy <re.emese@gmail.com>
Cc: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 35c9049b27 added
drivers/spi/omap_spi_100k.c.
This patch add the related clocks and pin muxing
entries to make the driver work on omap7xx platforms.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some chips, namely any OMAP1 chips using METHOD_MPUIO,
OMAP15xx and OMAP7xx, cannot be setup to respond to on-chip GPIO
interrupts in both rising and falling edge directions -- they can
only respond to one direction or the other, depending on how the
ICR is configured.
Additionally, current code forces rising edge detection if both
flags are specified:
if (trigger & IRQ_TYPE_EDGE_RISING)
l |= 1 << gpio;
else if (trigger & IRQ_TYPE_EDGE_FALLING)
l &= ~(1 << gpio);
else
goto bad;
This change implements a toggle function that will modify the ICR
to flip the direction of interrupt for IRQs that are requested with
both rising and falling flags. The toggle function is not called
for chips and GPIOs it does not apply to through the use of a flip_mask
that's added on a per-bank basis. The mask is only set for those
GPIOs where a toggle is necessary. Edge detection starts out the
same as above with FALLING mode first.
The toggle happens on EACH interrupt; without it, we have the
following sequence of actions on GPIO transition:
ICR GPIO Result
0x1 0 -> 1 (rising) Interrupt
0x1 1 -> 0 (falling) No interrupt
(set ICR to 0x0 manually)
0x0 0 -> 1 (rising) No interrupt
0x0 1 -> 0 (falling) Interrupt
That is, with the ICR set to 1 for a gpio, only rising edge interrupts
are caught, and with it set to 0, only falling edge interrupts are
caught. If we add in the toggle, we get this:
ICR GPIO Result
0x1 0 -> 1 (rising) Interrupt (ICR set to 0x0)
0x0 1 -> 0 (falling) Interrupt (ICR set to 0x1)
0x1 0 -> 1 ...
so, both rising and falling are caught, per the request for both
(IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING).
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In its current form, the omap_mcbsp_request() function can return after
irq_request() failure without any cleanups, effectively locking out the port
forever with clocks left running. Fix it.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] __per_cpu_idtrs[] is a memory hog
[IA64] sanity in #include files. Move fnptr to types.h
[IA64] use helpers for rlimits
[IA64] cpumask_of_node() should handle -1 as a node
normal users are currently allowed to set/modify ebtables rules.
Restrict it to processes with CAP_NET_ADMIN.
Note that this cannot be reproduced with unmodified ebtables binary
because it uses SOCK_RAW.
Signed-off-by: Florian Westphal <fwestphal@astaro.com>
Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>
We need to set the LRCLK inversion bit to select DSP mode.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org
Fix the following warning, which appears when the register dump for a
faulting process is printed in a kernel with SMP, DEBUG_PREEMPT, and
DEBUG_USER (with user_debug=31) enabled:
BUG: using smp_processor_id() in preemptible [00000000] code: init/1
caller is __show_regs+0x18/0x234
Backtrace:
[<c0159e5c>] (dump_backtrace+0x0/0x114) from [<c01faf30>] (dump_stack+0x18/0x1c)
r6:c781a000 r5:c0157544 r4:00000001 r3:00000000
[<c01faf18>] (dump_stack+0x0/0x1c) from [<c01e5230>] (debug_smp_processor_id+0xc4/0xf8)
[<c01e516c>] (debug_smp_processor_id+0x0/0xf8) from [<c0157544>] (__show_regs+0x18/0x234)
r6:c781bfb0 r5:00000000 r4:c781bfb0 r3:00000000
[<c015752c>] (__show_regs+0x0/0x234) from [<c01577a0>] (show_regs+0x40/0x50)
[<c0157760>] (show_regs+0x0/0x50) from [<c015c968>] (__do_user_fault+0x5c/0xa4)
r4:c781c000 r3:00000000
[<c015c90c>] (__do_user_fault+0x0/0xa4) from [<c015cbe0>] (do_page_fault+0x1b4/0x1e4)
r7:00000000 r6:00010000 r5:c781bfb0 r4:c781c000
[<c015ca2c>] (do_page_fault+0x0/0x1e4) from [<c01554c8>] (do_DataAbort+0x3c/0xa0)
[<c015548c>] (do_DataAbort+0x0/0xa0) from [<c01560c4>] (ret_from_exception+0x0/0x10)
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This updates the U300 defconfig to include the DMA driver merged
in 2.6.33-rc1 and adds a codepage that's needed to mount VFAT MMC
cards as default. The rest is new config options.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make registers unsigned for kernel space. This is important for
example in the perf events where the PC is stored into a u64. We
don't want it sign extended so make the regs unsigned to prevent
casts throughout the kernel.
Signed-off-by: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ref counting for the bh returned by gfs2_ea_find() was
wrong. This patch ensures that we always drop the ref count
to that bh correctly.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
The rename code was taking a resource group lock in cases where
it wasn't actually needed, this caused problems if the rename
was resulting in an inode being unlinked. The patch ensures that
we only take the rgrp lock early if it is really needed.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
The VFS reads the inode size during generic_file_aio_write() but
with no locking around it. In order to get the expected result
from O_APPEND opens, this patch updated the inode size before
calling generic_file_aio_write()
There is of course still a race here, in that there is nothing to
prevent another node coming in and extending the file in the
mean time. On the other hand, when used with file locking this
will ensure that the expected results are obtained.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Collect interrupt statistics, printable via debugfs:
debugfs/omapdss/dispc_irq
debugfs/omapdss/dsi_irq
The counters are reset when printed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
- dsi_vc_send_short() needs to use dest_per for the peripheral id
- dsi_vc_send_null() was always using channel id 0
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Fix e1000e_rar_set() to flush consecutive register writes to avoid write
combining which some parts cannot handle. Update e1000e_init_rx_addrs()
to call the fixed e1000e_rar_set() instead of duplicating code.
Also change e1000e_rar_set() to _not_ set the Address Valid bit if the MAC
address is all zeros.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e_enable_tx_pkt_filtering() will return a non-zero value if the
driver fails to enable the manageability interface on the host for
any reason; instead it should retun zero to indicate filtering has been
disabled. Also provide a single exit point for the function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adaptive IFS which involves writing to the Adaptive IFS Throttle register
was being done for all devices supported by the driver even though it is
not supported (i.e. the register doesn't even exist) on some devices. The
feature is supported on 8257x/82583 and ICH/PCH based devices, but not
on ESB2.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a change in pci_restore_state()[1] which clears the saved_state
flag, the driver should call pci_save_state() to set the flag once again
to avoid issues with EEH (same fix that recently was submitted for ixgbe).
[1] commmit 4b77b0a2ba
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o If tx and rx resources are not available, during set mac request.
Then this request wont be passed to firmware and it will be added to
driver mac list and will never make it to firmware.
So if resources are not available, don't add it to driver mac list.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o While unloading driver or resetting the context, tx ring was not
getting free.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch "sbawe: fix memory detection" fixed detection
for memoryless SB32 cards but broke detection of memory
above 512KB. This patch fixes the regression.
The patch has been tested on the SB32 card (CT3670) with
0MB, 2MB and 8MB memory installed.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The problem is that in the original code sound_nblocks could go up to 1024
which would be an array overflow.
This was found with a static checker and has been compile tested only.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
If for any reason we haven't installed handler we shouldn't try to
enable IRQ/MSI on the hw so we don't get unhandled IRQ/MSI which
makes the kernel sad.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In some case vblank might not be initialized and we shouldn't
try to use associated function. This patch make sure this is
the case. It also export drm_vblank_cleanup so driver can cleanup
vblank if for any reason IRQ/MSI is not working.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In some case we weren't releasing the AGP device at module unloading.
This leaded to unfunctional AGP at next module load. This patch make
sure we release the AGP bus if we acquire it.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
R300 family will hard lockup if host path read cache flush is
done through MMIO to HOST_PATH_CNTL. But scheduling same flush
through ring seems harmless. This patch remove the hdp_flush
callback and add a flush after each fence emission which means
a flush after each IB schedule. Thus we should have same behavior
without the hard lockup.
Tested on R100,R200,R300,R400,R500,R600,R700 family.
V2: Adjust fence counts in r600_blit_prepare_copy()
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Long story short, this fixes sporadic hardlocks with my rv410 during
times of intense 2D acceleration (Flash on Fx3).
V2: Fix indentation and move errata_fini to suspend function so we
don't leak scratch register over suspend/resume cycle.
V3: Move scratch_reg to asic specific structure (aim is to slowly
move stuff to asic specific structure and avoid poluting
radeon_device struct with asic specific variables)
Signed-off-by: Corbin Simpson <MostAwesomeDude@gmail.com>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This detects if the sideport memory is enabled and
if it is VRAM is evicted on suspend/resume.
This should fix s/r issues on some IGPs.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There are a couple of array overruns, and some associated confusion in
the code.
This is just a wild guess at what the code should actually look like.
Coverity CID: 13305 13306
agd5f: fix up the original intent of the timing code
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is displayport used for internal connections such
as laptop panels and systems with integrated monitors.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add a new connector type for eDP (embedded displayport)
eDP is more or less the same as DP but there are some
cases when you might want to handle it separately.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Makes it easier to keep in sync with ddx and the upstream
AMD versions.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Also remove the problematic enums that were unused
remnants from the ddx.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Somehow, strange characters made their way zaurus gpio .desc
fields. Fix it.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Stanislav Brabec <utx@penguin.cz>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
In the driver probe function the emac module clock needs to
be enabled before calling register_netdev(). As soon as the
device is registered the driver get_stats function can be invoked
by the core - the module clock must be switched on to be able to
read from stats registers. Also explicitly call matching clk_disable
for failure conditions in probe function.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
