* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6: (61 commits)
gpio/mxc/mxs: fix build error introduced by the irq_gc_ack() renaming
mcp23s08: add i2c support
mcp23s08: isolate spi specific parts
mcp23s08: get rid of setup/teardown callbacks
gpio/tegra: dt: add binding for gpio polarity
mcp23s08: remove unused work queue
gpio/da9052: remove a redundant assignment for gpio->da9052
gpio/mxc: add device tree probe support
ARM: mxc: use ARCH_NR_GPIOS to define gpio number
gpio/mxc: get rid of the uses of cpu_is_mx()
gpio/mxc: add missing initialization of basic_mmio_gpio shadow variables
gpio: Move mpc5200 gpio driver to drivers/gpio
GPIO: DA9052 GPIO module v3
gpio/tegra: Use engineering names in DT compatible property
of/gpio: Add new method for getting gpios under different property names
gpio/dt: Refine GPIO device tree binding
gpio/ml-ioh: fix off-by-one for displaying variable i in dev_err
gpio/pca953x: Deprecate meaningless device-tree bindings
gpio/pca953x: Remove dynamic platform data pointer
gpio/pca953x: Fix IRQ support.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1287 commits)
icmp: Fix regression in nexthop resolution during replies.
net: Fix ppc64 BPF JIT dependencies.
acenic: include NET_SKB_PAD headroom to incoming skbs
ixgbe: convert to ndo_fix_features
ixgbe: only enable WoL for magic packet by default
ixgbe: remove ifdef check for non-existent define
ixgbe: Pass staterr instead of re-reading status and error bits from descriptor
ixgbe: Move interrupt related values out of ring and into q_vector
ixgbe: add structure for containing RX/TX rings to q_vector
ixgbe: inline the ixgbe_maybe_stop_tx function
ixgbe: Update ATR to use recorded TX queues instead of CPU for routing
igb: Fix for DH89xxCC near end loopback test
e1000: always call e1000_check_for_link() on e1000_ce4100 MACs.
netxen: add fw version compatibility check
be2net: request native mode each time the card is reset
ipv4: Constrain UFO fragment sizes to multiples of 8 bytes
virtio_net: Fix panic in virtnet_remove
ipv6: make fragment identifications less predictable
ipv6: unshare inetpeers
can: make function can_get_bittiming static
...
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: Fix in/out emulation
lguest: Fix translation count about wikipedia's cpuid page
lguest: Fix three simple typos in comments
lguest: update comments
lguest: Simplify device initialization.
lguest: don't rewrite vmcall instructions
lguest: remove remaining vmcall
lguest: use a special 1:1 linear pagetable mode until first switch.
lguest: Do not exit on non-fatal errors
* 'linux-next' of git://git.infradead.org/ubifs-2.6: (32 commits)
MAINTAINERS: change e-mail of Adrian Hunter
UBIFS: fix master node recovery
UBIFS: improve power cut emulation testing
UBIFS: rename recovery testing variables
UBIFS: remove custom list of superblocks
UBIFS: stop re-defining UBI operations
UBIFS: switch to I/O helpers
UBIFS: switch to ubifs_leb_write
UBIFS: switch to ubifs_leb_read
UBIFS: introduce more I/O helpers
UBIFS: always print stacktrace when switching to R/O mode
UBIFS: remove unused and unneeded debugging function
UBIFS: add global debugfs knobs
UBIFS: introduce debugfs helpers
UBIFS: re-arrange debugging code a bit
UBIFS: be more informative in failure mode
UBIFS: switch self-check knobs to debugfs
UBIFS: lessen amount of debugging check types
UBIFS: introduce helper functions for debugging checks and tests
UBIFS: amend debugging inode size check function prototype
...
We used to notify the Host every time we updated a device's status. However,
it only really needs to know when we're resetting the device, or failed to
initialize it, or when we've finished our feature negotiation.
In particular, we used to wait for VIRTIO_CONFIG_S_DRIVER_OK in the
status byte before starting the device service threads. But this
corresponds to the successful finish of device initialization, which
might (like virtio_blk's partition scanning) use the device. So we
had a hack, if they used the device before we expected we started the
threads anyway.
Now we hook into the finalize_features hook in the Guest: at that
point we tell the Launcher that it can rely on the features we have
acked. On the Launcher side, we look at the status at that point, and
start servicing the device.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This patch adds new information for the driver
especially about its platform structure fields.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation about the background and the design of mmc non-blocking.
Host driver guidelines to minimize request preparation overhead.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86. reboot: Make Dell Latitude E6320 use reboot=pci
x86, doc only: Correct real-mode kernel header offset for init_size
x86: Disable AMD_NUMA for 32bit for now
Add overview documentation in Documentation/ABI/stable/firewire-cdev.
Improve the inline reference documentation in firewire-cdev.h:
- Add /* available since kernel... */ comments to event numbers
consistent with the comments on ioctl numbers.
- Shorten some documentation on an event and an ioctl that are
less interesting to current programming because there are newer
preferable variants.
- Spell Configuration ROM (name of an IEEE 1212 register) in
upper case.
- Move the dummy FW_CDEV_VERSION out of the reader's field of
vision. We should remove it from the header next year or so.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Allocate one bit in the available extra cell to indicate if the gpio
should be considered logically inverted.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
slip: fix wrong SLIP6 ifdef-endif placing
natsemi: fix another dma-debug report
sctp: ABORT if receive, reassmbly, or reodering queue is not empty while closing socket
net: Fix default in docs for tcp_orphan_retries.
hso: fix a use after free condition
net/natsemi: Fix module parameter permissions
XFRM: Fix memory leak in xfrm_state_update
sctp: Enforce retransmission limit during shutdown
mac80211: fix TKIP replay vulnerability
mac80211: fix ie memory allocation for scheduled scans
ssb: fix init regression of hostmode PCI core
rtlwifi: rtl8192cu: Add new USB ID for Netgear WNA1000M
ath9k: Fix tx throughput drops for AR9003 chips with AES encryption
carl9170: add NEC WL300NU-AG usbid
cfg80211: fix deadlock with rfkill/sched_scan by adding new mutex
ath5k: fix incorrect use of drvdata in PCI suspend/resume code
ath5k: fix incorrect use of drvdata in sysfs code
Bluetooth: Fix memory leak under page timeouts
Bluetooth: Fix regression with incoming L2CAP connections
Bluetooth: Fix hidp disconnect deadlocks and lost wakeup
...
Resize feature was supported by the commit 4e33f9eab0 but it was not
reflected to the list of unsupported features in nilfs2.txt file.
This updates the list to fix discrepancy.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
v2: incorporated suggestions from Randy Dunlap
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The real-mode kernel header init_size field is located at 0x260 per the field
listing in th e"REAL-MODE KERNEL HEADER" section. It is listed as 0x25c in
the "DETAILS OF HEADER FIELDS" section, which overlaps with pref_address.
Correct the details listing to 0x260.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Link: http://lkml.kernel.org/r/541cf88e2dfe5b8186d8b96b136d892e769a68c1.1310441260.git.dvhart@linux.intel.com
CC: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
That file harkens back to the days of the big 2.4 -> 2.6 version jump,
and was based even then on older versions. Some of it is just obsolete,
and Jesper Juhl points out that it talks about kernel versions 2.6 and
should be updated to 3.0.
Remove some obsolete text, and re-phrase some other to not be 2.6-specific.
Reported-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] msp3400: fill in v4l2_tuner based on vt->type field
[media] tuner-core.c: don't change type field in g_tuner or g_frequency
[media] cx18/ivtv: fix g_tuner support
[media] tuner-core: power up tuner when called with s_power(1)
[media] v4l2-ioctl.c: check for valid tuner type in S_HW_FREQ_SEEK
[media] tuner-core: simplify the standard fixup
[media] tuner-core/v4l2-subdev: document that the type field has to be filled in
[media] v4l2-subdev.h: remove unused s_mode tuner op
[media] feature-removal-schedule: change in how radio device nodes are handled
[media] bttv: fix s_tuner for radio
[media] pvrusb2: fix g/s_tuner support
[media] v4l2-ioctl.c: prefill tuner type for g_frequency and g/s_tuner
[media] tuner-core: fix tuner_resume: use t->mode instead of t->type
[media] tuner-core: fix s_std and s_tuner
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
hp-wmi: fix use after free
dell-laptop - using buffer without mutex_lock
Revert: "dell-laptop: Toggle the unsupported hardware killswitch"
platform-drivers-x86: set backlight type to BACKLIGHT_PLATFORM
thinkpad-acpi: handle HKEY 0x4010, 0x4011 events
drivers/platform/x86: Fix memory leak
thinkpad-acpi: handle some new HKEY 0x60xx events
acer-wmi: fix bitwise bug when set device state
acer-wmi: Only update rfkill status for associated hotkey events
Since we removed sti()/cli() and related, how about removing it from
Documentation/spinlocks.txt?
Signed-off-by: Muthukumar R <muthur@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I changed the TKIP key functions, but forgot to
update the documentation includes, fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Multiple attempts to dynamically reallocate pci resources have
unfortunately lead to regressions. Though we continue to fix the
regressions and fine tune the dynamic-reallocation behavior, we have not
reached a acceptable state yet.
This patch provides a interim solution. It disables dynamic reallocation
by default, but adds the ability to enable it through pci=realloc kernel
command line parameter.
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The patch adds device tree probe support for gpio-mxc driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add an FS-Cache helper to bulk uncache pages on an inode. This will
only work for the circumstance where the pages in the cache correspond
1:1 with the pages attached to an inode's page cache.
This is required for CIFS and NFS: When disabling inode cookie, we were
returning the cookie and setting cifsi->fscache to NULL but failed to
invalidate any previously mapped pages. This resulted in "Bad page
state" errors and manifested in other kind of errors when running
fsstress. Fix it by uncaching mapped pages when we disable the inode
cookie.
This patch should fix the following oops and "Bad page state" errors
seen during fsstress testing.
------------[ cut here ]------------
kernel BUG at fs/cachefiles/namei.c:201!
invalid opcode: 0000 [#1] SMP
Pid: 5, comm: kworker/u:0 Not tainted 2.6.38.7-30.fc15.x86_64 #1 Bochs Bochs
RIP: 0010: cachefiles_walk_to_object+0x436/0x745 [cachefiles]
RSP: 0018:ffff88002ce6dd00 EFLAGS: 00010282
RAX: ffff88002ef165f0 RBX: ffff88001811f500 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000100 RDI: 0000000000000282
RBP: ffff88002ce6dda0 R08: 0000000000000100 R09: ffffffff81b3a300
R10: 0000ffff00066c0a R11: 0000000000000003 R12: ffff88002ae54840
R13: ffff88002ae54840 R14: ffff880029c29c00 R15: ffff88001811f4b0
FS: 00007f394dd32720(0000) GS:ffff88002ef00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00007fffcb62ddf8 CR3: 000000001825f000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process kworker/u:0 (pid: 5, threadinfo ffff88002ce6c000, task ffff88002ce55cc0)
Stack:
0000000000000246 ffff88002ce55cc0 ffff88002ce6dd58 ffff88001815dc00
ffff8800185246c0 ffff88001811f618 ffff880029c29d18 ffff88001811f380
ffff88002ce6dd50 ffffffff814757e4 ffff88002ce6dda0 ffffffff8106ac56
Call Trace:
cachefiles_lookup_object+0x78/0xd4 [cachefiles]
fscache_lookup_object+0x131/0x16d [fscache]
fscache_object_work_func+0x1bc/0x669 [fscache]
process_one_work+0x186/0x298
worker_thread+0xda/0x15d
kthread+0x84/0x8c
kernel_thread_helper+0x4/0x10
RIP cachefiles_walk_to_object+0x436/0x745 [cachefiles]
---[ end trace 1d481c9af1804caa ]---
I tested the uncaching by the following means:
(1) Create a big file on my NFS server (104857600 bytes).
(2) Read the file into the cache with md5sum on the NFS client. Look in
/proc/fs/fscache/stats:
Pages : mrk=25601 unc=0
(3) Open the file for read/write ("bash 5<>/warthog/bigfile"). Look in proc
again:
Pages : mrk=25601 unc=25601
Reported-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-and-Tested-by: Suresh Jayaraman <sjayaraman@suse.de>
cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Radio devices have weird side-effects when used with combined TV/radio
tuners and the V4L2 spec is ambiguous on how it should work. This results
in inconsistent driver behavior which makes life hard for everyone.
Be more strict in when and how the switch between radio and tv mode
takes place and make sure all drivers behave the same.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Handle events 0x4010 and 0x4011 so that we do not pester users about them.
These events report when the thinkpad is docked/undocked to a native
hotplug dock (i.e. one that does not need ACPI handling, nor is represented
in the ACPI device tree). Such docks are based on USB 2.0/3.0, and also
work as port replicators.
We really want a proper dock class to report these, or at least new input
EV_SW events. Since it is not clear which one to use yet, keep reporting
them as vendor-specific ThinkPad events.
WARNING: As defined by the thinkpad-acpi sysfs ABI rules of engagement, the
vendor-specific events will be REMOVED as soon as generic events are made
available (duplicate events are a big problem), with an appropriate update
to the thinkpad-acpi sysfs/event ABI versioning. Userspace is already
prepared to provide easy backwards compatibility for such changes when
convenient to the distro (see acpi-fakekey).
* Event 0x4010: docking to hotplug dock/port replicator
* Event 0x4011: undocking from hotplug dock/port replicator
Typical usecase would be to trigger display reconfiguration.
Reports mention T410, T510, and series 3 docks/port replicators. Special
thanks to Robert de Rooy for his extensive report and analysis of the
situation.
http://www.thinkwiki.org/wiki/ThinkPad_Port_Replicator_Series_3http://www.thinkwiki.org/wiki/ThinkPad_Mini_Dock_Series_3http://www.thinkwiki.org/wiki/ThinkPad_Mini_Dock_Plus_Series_3http://www.thinkwiki.org/wiki/ThinkPad_Mini_Dock_Plus_Series_3_for_Mobile_Workstationshttp://lenovoblogs.com/insidethebox/?p=290
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Reported-by: Claudius Hubig <claudiushubig@chubig.net>
Reported-by: Doctor Bill <docbill@gmail.com>
Reported-by: Korte Noack <gbk.noack@gmx.de>
Reported-by: Robert de Rooy <robert.de.rooy@gmail.com>
Reported-by: Sebastian Will <swill@csail.mit.edu>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Handle some user interface events from the newer Lenovo models. We are likely
to do something smart with these events in the future, for now, hide the ones
we are already certain about from the user and userspace both.
* Events 0x6000 and 0x6005 are key-related. 0x6005 is not properly identified
yet. Ignore these events, and do not report them.
* Event 0x6040 has not been properly identified yet, and we don't know if it
is important (looks like it isn't, but still...). Keep reporting it.
* Change the message the driver outputs on unknown 0x6xxx events, as all
recent events are not related to thermal alarms. Degrade log level from
ALERT to WARNING.
Thanks to all users who reported these events or asked about them in a number
of mailing lists. Your help is highly appreciated, even if I did took a lot of
time to act on them. For that I apologise.
I will list those that identified the reasons for the events as "reported-by",
and I apologise in advance if I leave anyone out: it was not done on purpose, I
made the mistake of not properly tagging all event report emails separately,
and might have missed some.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Reported-by: Markus Malkusch <markus@malkusch.de>
Reported-by: Peter Giles <g1l3sp@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Fix following warning in ifenslave.c with gcc version 4.5.2 (Ubuntu/Linaro 4.5.2-8ubuntu4).
Documentation/networking/ifenslave.c:263:4: warning: format not a string literal and no format arguments
Documentation/networking/ifenslave.c:271:3: warning: format not a string literal and no format arguments
Documentation/networking/ifenslave.c:277:3: warning: format not a string literal and no format arguments
Documentation/networking/ifenslave.c:285:3: warning: format not a string literal and no format arguments
Documentation/networking/ifenslave.c:291:3: warning: format not a string literal and no format arguments
Documentation/networking/ifenslave.c:292:3: warning: format not a string literal and no format arguments
Documentation/networking/ifenslave.c:312:4: warning: format not a string literal and no format arguments
Documentation/networking/ifenslave.c:323:3: warning: format not a string literal and no format arguments
Documentation/networking/ifenslave.c:342:4: warning: format not a string literal and no format arguments
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the blkio.throttle.* file names are incorrectly reported without
".throttle" in the documentation. Fix it.
Signed-off-by: Andrea Righi <andrea@betterlinux.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The list of available general purpose memory allocators in
Documentation/CodingStyle chapter 14 is incomplete. This patch adds
the missing vzalloc() to the list.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Engineering names are more stable than marketing names. Hence, use them
for Device Tree compatible properties instead.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Signed-off-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tcp_rmem and tcp_wmem use 1 page as default value for the minimum
amount of memory to be used, same as udp_wmem_min and udp_rmem_min.
Pages are different size on different architectures - use the right
units when describing the defaults.
Reviewed-by: Shan Wei <shanwei@cn.fujitsu.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Max Matveev <makc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp does not use second and third ("default" and "max") values
of sctp_rmem tunable. The format is the same as tcp_rmem
but the meaning is different so make the documentation explicit to
avoid confusion.
sctp_wmem is not used at all.
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Max Matveev <makc@redhat.com>
Reviewed-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UBIFS has many built-in self-check functions which can be enabled using the
debug_chks module parameter or the corresponding sysfs file
(/sys/module/ubifs/parameters/debug_chks). However, this is not flexible enough
because it is not per-filesystem. This patch moves this to debugfs interfaces.
We already have debugfs support, so this patch just adds more debugfs files.
While looking at debugfs support I've noticed that it is racy WRT file-system
unmount, and added a TODO entry for that. This problem has been there for long
time and it is quite standard debugfs PITA. The plan is to fix this later.
This patch is simple, but it is large because it changes many places where we
check if a particular type of checks is enabled or disabled.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
We have too many different debugging checks - lessen the amount by merging all
index-related checks into one. At the same time, move the "force in-the-gap"
test to the "index checks" class, because it is too heavy for the "general"
class.
This patch merges TNC, Old index, and Index size check and calles this just
"index checks".
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (k10temp) Update documentation for Fam12h
hwmon-vid: Fix typo in VIA CPU name
hwmon: (f71882fg) Add support for the F71869A
hwmon: Use <> rather than () around my e-mail address
hwmon: (emc6w201) Properly handle all errors
Add some CPU series IDs and links to the Fam12h datasheets.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
