Commit Graph

42 Commits

Author SHA1 Message Date
Catalin Marinas
f7e7aa5850 USB: Add platform device support for the ISP1760 USB chip
Currently, the driver only supports PCI and PPC_OF but there are
boards like ARM RealView where this is a platform device. The patch adds
the necessary functions and registration to the isp1760-if.c file and
modifies the corresponding Makefile and Kconfig to be able to use this
driver even if PCI and PPC_OF are not enabled.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-24 16:20:31 -07:00
Ivan Kuten
26e1287594 USB: Correct Makefile to make isp1760 buildable
Signed-off-by: Ivan Kuten <ivan.kuten@promwad.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-09 11:19:49 -08:00
Anton Vorontsov
236dd4d18f USB: Driver for Freescale QUICC Engine USB Host Controller
This patch adds support for the FHCI USB controller, as found
in the Freescale MPC836x and MPC832x processors. It can support
Full or Low speed modes.

Quite a lot the hardware is doing by itself (SOF generation, CRC
generation and checking), though scheduling and retransmission is on
software's shoulders.

This controller does not integrate the root hub, so this driver also
fakes one-port hub. External hub is required to support more than
one device.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-27 16:15:38 -08:00
Inaky Perez-Gonzalez
d09318b8ab wusb: add HWA host controller driver
Add a driver for Wireless USB host controllers connected via USB (a
Host Wire Adapter or HWA).

Signed-off-by: David Vrabel <david.vrabel@csr.com>
2008-09-17 16:54:31 +01:00
Greg Kroah-Hartman
470cc41503 wusb: add the Wireless USB core (build-system)
Add the WUSB build system (Kconfig and Kbuild) files.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David Vrabel <david.vrabel@csr.com>
2008-09-17 16:54:30 +01:00
Peter Korsgaard
e9b29ffc51 USB: add Cypress c67x00 OTG controller HCD driver
This patch adds HCD support for the Cypress c67x00 family of devices.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-05-02 10:25:57 -07:00
Adrian Bunk
0e66fb3492 USB: always visit drivers/usb/misc/
Currently, every driver under drivers/usb/misc/ also has to be listed in
drivers/usb/Makefile. This has been forgotten more than once, and this
patch changes drivers/usb/Makefile to simply always visit
drivers/usb/misc/ when building the USB code.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Toralf Förster <toralf.foerster@gmx.de>
Acked-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12 14:55:26 -07:00
Nico Erfurth
a1d534bb23 USB: Add drivers/usb/misc/iowarrior.c to the Makefile
This patch adds the new iowarrior module to the Makefile in drivers/usb.
Currently the module isn't build unless another driver from usb/misc is
selected.

Signed-off-by: Nico Erfurth <masta@perlgolf.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12 14:55:02 -07:00
Juergen Beisert
1aebb781e3 USB: devices misc: Trivial patch to build the IOWARRIOR when it is selected in Kconfig
Trivial patch to build the IOWARRIOR when it is selected in Kconfig.

Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-30 13:27:43 -07:00
Robert P. J. Day
a603c66551 USB: remove Makefile reference to obsolete OHCI_AT91
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-12 16:34:41 -07:00
Yoshihiro Shimoda
5d3043586d USB: r8a66597-hcd: host controller driver for R8A66597
I would like to submit Renesas R8A66597 USB HCD driver.

R8A66597 is Renesas USB 2.0 host and peripheral combined
controller device originally designed for embedded products.
As a limitation of this device, it does not support externel
hub more than 2 tier, and cannot communicate with a USB
device more than 10. Then this device is not compatible with
EHCI and/or OHCI, I wrote driver support patch based on
sl811 code.

This driver has the following unique specifications:
- Implement transfer timeout to share one pipe with plural endpoint.
- Detach detection of a USB device connected to externel hub.

The driver has been tested external hub, usb-hdd, usb-cdrom,
usb-speaker, mice, keyboard, and usbtest driver.

Signed-off-by : Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-12 16:29:45 -07:00
Jeff Garzik
5b2fc49991 Move USB network drivers to drivers/net/usb.
It is preferable to group drivers by usage (net, scsi, ATA, ...) than
by bus.  When reviewing drivers, the [PCI|USB|PCMCIA|...] maintainer
is probably less qualified on networking issues than a networking
maintainer.  Also, from a practical standpoint, chips often
appear on multiple buses, which is why we do not put drivers into
drivers/pci/net.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-09 21:31:55 -04:00
Dmitry Torokhov
ba0acb5ee3 Input: move USB miscellaneous devices under drivers/input/misc
This will allow concentrating all input devices in one place
in {menu|x|q}config.

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-05-08 01:41:29 -04:00
Dmitry Torokhov
1c362d4682 Input: move USB gamepads under drivers/input/joystick
This will allow concentrating all input devices in one place
in {menu|x|q}config.

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-05-08 01:41:29 -04:00
Dmitry Torokhov
d05e84e6cb Input: move USB touchscreens under drivers/input/touchscreen
This will allow concentrating all input devices in one place
in {menu|x|q}config.

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-05-08 01:41:29 -04:00
Dmitry Torokhov
4104d13fe0 Input: move USB tablets under drivers/input/tablet
This will allow concentrating all input devices in one place
in {menu|x|q}config.

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-05-08 01:41:29 -04:00
Linus Torvalds
d6454706c3 Merge branch 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid: (21 commits)
  USB HID: don't warn on idVendor == 0
  USB HID: add 'quirks' module parameter
  USB HID: add support for dynamically-created quirks
  USB HID: clarify static quirk handling as squirks
  USB HID: encapsulate quirk handling into hid-quirks.c
  USB HID: EMS USBII device needs HID_QUIRK_MULTI_INPUT
  HID: update copyright and authorship macro
  HID: introduce proper zeroing of unused bits in output reports
  USB HID: add support for WiseGroup MP-8800 Quad Joypad
  USB HID: add FF support for Logitech Force 3D Pro Joystick
  USB HID: numlock quirk for dell W7658 keyboard
  USB HID: Logitech MX3000 keyboard needs report descriptor quirk
  USB HID: extend quirk for Logitech S510 keyboard
  USB HID: usbkbd/usbmouse - handle errors when registering devices
  USB HID: add QUIRK_HIDDEV for Belkin Flip KVM
  HID: enable dead keys on a belkin wireless keyboard
  USB HID: Thustmaster firestorm dual power v1 support
  USB HID: specify explicit size for hid_blacklist.quirks
  USB HID: fix retry & reset logic
  USB HID: consolidate vendor/product ids
  ...
2007-04-30 08:58:21 -07:00
David Brownell
1b101ceb91 USB: remove ancient/broken CRIS hcd
Remove the old crisv10 HCD ... it can't have built for some time,
doesn't even have a Kconfig entry, was the last driver not to have
been converted to the "hcd" framework, and considering the usbcore
changes since its last patch was merged, has just got to buggy as
all get-out.

I'm told Axis has a new driver, and will be submitting it soon.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-04-27 13:28:42 -07:00
Jiri Kosina
6db3dfefa2 USB HID: move usbhid code from drivers/usb/input to drivers/hid/usbhid
Separate usbhid code into dedicated drivers/hid/usbhid directory as
discussed previously with Greg, so that it eases maintaineance process.

Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-04-11 10:36:02 +02:00
Greg Kroah-Hartman
df23fa01ac USB: Driver to charge USB blackberry devices
A simple driver to turn on the charging capability of a USB BlackBerry
device when it is plugged into the machine.  It does not bind to the
device, so all userspace programs can still sync properly with it.

Note, if CONFIG_USB_SUSPEND is enabled, it can play havoc with this
device as the power to the port will be shut down.  This device id will
have to be added to the global blacklist table when it is created.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-16 15:32:17 -08:00
Greg Kroah-Hartman
9fcde23527 USB: move trancevibrator.c to the proper usb directory
It's not a input driver, so it doesn't belong in the input directory.


Cc: Sam Hocevar <sam@zoy.org>
Cc: Dmitry Torokhov <dtor@insightbb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-10-17 14:46:32 -07:00
Tony Olech
d774efeabc USB: u132-hcd: host controller driver for ELAN U132 adapter
This "u132-hcd" module is one half of the "driver" for
ELAN's U132 which is a USB to CardBus OHCI controller
adapter. This module needs the "ftdi-elan" module in
order to communicate to CardBus OHCI controller inserted
into the U132 adapter.

When the "ftdi-elan" module detects a supported CardBus
OHCI controller in the U132 adapter it loads this "u132-hcd"
module.

Upon a successful device probe() the single workqueue
is started up which does all the processing of commands
from the USB core that implement the host controller.

The workqueue maintains the urb queues and issues commands
via the functions exported by the "ftdi-elan" module. Each
such command will result in a callback.

Note that the "ftdi-elan" module is a USB client driver.

Note that this "u132-hcd" module is a (cut-down OHCI)
host controller.

Thus we have a topology with the parent of a host controller
being a USB client! This really stresses the USB subsystem
semaphore/mutex handling in the module removal.

Signed-off-by: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-27 11:58:59 -07:00
Tony Olech
a5c66e4b24 USB: ftdi-elan: client driver for ELAN Uxxx adapters
This "ftdi-elan" module is one half of the "driver" for
ELAN's Uxxx series adapters which are USB to PCMCIA CardBus
adapters. Currently only the U132 adapter is available and
it's module is called "u132-hcd".

When the USB hot plug subsystem detects a Uxxx series adapter
it should load this module.

Upon a successful device probe() the jtag device file interface
is created and the status workqueue started up.

The jtag device file interface exists for the purpose of
updating the firmware in the Uxxx series adapter, but as
yet it had never been used.

The status workqueue initializes the Uxxx and then sits there
polling the Uxxx until a supported PCMCIA CardBus device is
detected it will start the command and respond workqueues
and then load the module that handles the device. This will
initially be only the u132-hcd module. The status workqueue
then just polls the Uxxx looking for card ejects.

The command and respond workqueues implement a command
sequencer for communicating with the firmware on the other
side of the FTDI chip in the Uxxx. This "ftdi-elan" module
exports some functions to interface with the sequencer.

Note that this module is a USB client driver.

Note that the "u132-hcd" module is a (cut-down OHCI)
host controller.

Thus we have a topology with the parent of a host controller
being a USB client! This really stresses the USB subsystem
semaphore/mutex handling in the module removal.

Signed-off-by: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-27 11:58:59 -07:00
Sam Hocevar
5638e4d92e USB: add PlayStation 2 Trance Vibrator driver
This patch is a driver for the PlayStation 2 specific Trance Vibrator
device. The only thing that device can do is vibrate at various speeds.

Signed-off-by: Sam Hocevar <sam@zoy.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Luiz Fernando N. Capitulino" <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-27 11:58:59 -07:00
Steven Haigh
03270634e2 USB: Add ADU support for Ontrak ADU devices
This patch adds support for Ontrak ADU USB devices.

Fixed for printk issues by Randy Dunlap <rdunlap@xenotime.net>

Signed-off-by: Steven Haigh <netwiz@crc.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-27 11:58:59 -07:00
Oliver Bock
9189bfc2df [PATCH] USB: rename Cypress CY7C63xxx driver to proper name and fix up some tiny things
This is a new driver for the Cypress CY7C63xxx mirco controller series.
It currently supports the pre-programmed CYC63001A-PC by AK Modul-Bus
GmbH.  It's based on a kernel 2.4 driver (cyport) by Marcus Maul which I
ported to kernel 2.6 using sysfs. I intend to support more controllers
of this family (and more features) as soon as I get hold of the required
IDs etc. Please see the source code's header for more information.

Signed-off-by: Oliver Bock <o.bock@fh-wolfenbuettel.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-07-12 16:03:21 -07:00
Oliver Bock
4255e6f6d9 [PATCH] USB: new driver for Cypress CY7C63xxx mirco controllers
This is a new driver for the Cypress CY7C63xxx mirco controller series.
It currently supports the pre-programmed CYC63001A-PC by AK Modul-Bus
GmbH.  It's based on a kernel 2.4 driver (cyport) by Marcus Maul which I
ported to kernel 2.6 using sysfs. I intend to support more controllers
of this family (and more features) as soon as I get hold of the required
IDs etc. Please see the source code's header for more information.

Signed-off-by: Oliver Bock <o.bock@fh-wolfenbuettel.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-21 15:04:17 -07:00
akpm@osdl.org
069e8a65cd [PATCH] Driver for Apple Cinema Display
This is a driver to control the brightness of an Apple Cinema Display over
USB.  It updates the local brightness value if the user presses a button on
the display.

Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-21 15:04:14 -07:00
Mauro Carvalho Chehab
9f6933be66 V4L/DVB (3599a): Move drivers/usb/media to drivers/media/video
Because of historic reasons, there are two separate directories with
V4L stuff. Most drivers are located at driver/media/video. However, some
code for USB Webcams were inserted under drivers/usb/media.

This makes difficult for module authors to know were things should be.
Also, makes Kconfig menu confusing for normal users.

This patch moves all V4L content under drivers/usb/media to
drivers/media/video, and fixes Kconfig/Makefile entries.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2006-03-25 09:29:04 -03:00
Andrew Victor
39a269c09f [PATCH] USB: add support for OCHI on AT91rm9200
This adds support for OHCI on AT91rm9200 based boards.

Possibly of interest here is the way this uses <linux/clk.h> to
gate clocks on/off during system pm state transitions.  That's
typical for non-PCI systems.  Some can go further; Mini-A host
side connectors enable ID-pin sensing.

From: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-03-20 14:49:55 -08:00
Adrian Bunk
9628416a54 [PATCH] USB: remove OBSOLETE_OSS_USB_DRIVER drivers
This patch removes the obsolete USB_MIDI and USB_AUDIO drivers.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-03-20 14:49:54 -08:00
Luca Risolia
60f780528f [PATCH] USB: Add ZC0301 Video4Linux2 driver
This patch adds a Video4Linux2 driver for ZC0301
Image Processor and Control Chip.

Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-03-20 14:49:52 -08:00
Luca Risolia
7ce08c93e3 [PATCH] USB: Add ET61X[12]51 Video4Linux2 driver
This patch adds a Video4Linux2 driver giving support
to ET61X151 and ET61X251 PC Camera Controllers made by
Etoms Electronics.

Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-31 17:23:39 -08:00
Pete Zaitcev
a00828e9ac [PATCH] USB: drivers/usb/storage/libusual
This patch adds a shim driver libusual, which routes devices between
usb-storage and ub according to the common table, based on unusual_devs.h.
The help and example syntax is in Kconfig.

Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-04 13:48:31 -08:00
Greg Kroah-Hartman
a6c82600d4 [PATCH] USB: delete the bluetty driver
We have a real Bluetooth system in Linux, lets finally delete this driver as no
one is using it (and if they are, they are using a closed source bluetooth
stack, which I can't support anyway.)

Marcel, you owe me a beer :)

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-10-28 16:47:47 -07:00
David Brownell
7586269c0b [PATCH] USB: move handoff code
This moves the PCI quirk handling for USB host controllers from the
PCI directory to the USB directory.  Follow-on patches will need to:

(a) merge these copies with the originals in the HCD reset methods.
they don't wholly agree, despite doing the very same thing; and

(b) eventually change it so "usb-handoff" is the default, to help
get more robust USB/BIOS/input/... interactions.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/Makefile              |    2
 drivers/pci/quirks.c          |  253 ---------------------------------------
 drivers/usb/Makefile          |    1
 drivers/usb/host/Makefile     |    5
 drivers/usb/host/pci-quirks.c |  272 ++++++++++++++++++++++++++++++++++++++++++
 5 files changed, 280 insertions(+), 253 deletions(-)
2005-10-28 16:47:38 -07:00
Michael Hund
2824bd250f [PATCH] USB: add ldusb driver
The following driver provides complete interrupt-in and interrupt-out
reports (raw data) to a user program. Until now it uses the
HIDIOCGDEVINFO ioctl call, because I don't know better :-(. Perhaps, it
will be ok for you - and I will be happy, if you assign 8 minor numbers.

I have tested it in several environments and it works very well for me.
However, it has a problem with two or more devices at the same hub, if
the two or more devices need 1 ms interrupt-in transfers. Unfortunately
more than one interrupt-in transfer every ms isn't possible (ehci
driver?). This is why the min_interrupt_in_interval and
min_interrupt_out_interval are increased to 2 ms (see the corresponding
module parameters). This way, I can use two devices simultaneously at
the same hub.

Signed-off-by: Michael Hund <mhund@ld-didactic.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-07-12 11:52:57 -07:00
Thomas Winischhofer
ead99eb001 [PATCH] USB: SiS USB Makefile fixes
although 2.6.12 now contains the sisusb driver, it failes to build this
driver due to a missing patch of the Makefile.

From: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-07-12 11:52:55 -07:00
Linus Torvalds
d3b8a1a849 Merge master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6 2005-06-27 15:13:26 -07:00
Olav Kongas
4808a1c026 [PATCH] USB: Add isp116x-hcd USB host controller driver
This patch provides an "isp116x-hcd" driver for Philips'
ISP1160/ISP1161 USB host controllers.

The driver:
 - is relatively small, meant for use on embedded platforms.
 - runs usbtests 1-14 without problems for days.
 - has been in use by 6-7 different people on ARM and PPC platforms,
   running a range of devices including USB hubs.
 - supports suspend/resume of both the platform device and the root hub;
   supports remote wakeup of the root hub (but NOT the platform device)
   by USB devices.
 - does NOT support ISO transfers (nobody has asked for them).
 - is PIO-only.

Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-06-27 14:43:42 -07:00
Stephane VOLTZ
5388054697 Input: add driver for Acecad Flair USB tablets
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2005-06-06 02:22:37 -05:00
Linus Torvalds
1da177e4c3 Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00