Commit Graph

89 Commits

Author SHA1 Message Date
Hans de Goede
5e7515ba78 pinctrl: sunxi: Fix A33 external interrupts not working
pinctrl-sun8i-a33.c (and the dts) declare only 2 interrupt banks,
where as the closely related a23 has 3 banks. This matches with the
datasheet for the A33 where only interrupt banks B and G are specified
where as the A23 has banks A, B and G.

However the A33 being the A23 derative it is means that the interrupt
configure/status io-addresses for the 2 banks it has are not changed
from the A23, iow they have the same address as if bank A was still
present. Where as the sunxi pinctrl currently tries to use the A23 bank
A addresses for bank B, since the pinctrl code does not know about the
removed bank A.

Add a irq_bank_base parameter and use this where appropriate to take
the missing bank A into account.

This fixes external interrupts not working on the A33 (tested with
an i2c touchscreen controller which uses an external interrupt).

Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-03-30 10:57:52 +02:00
Linus Torvalds
1a46712aa9 This is the bulk of GPIO changes for kernel v4.6:
Core changes:
 
 - The gpio_chip is now a *real device*. Until now the gpio chips
   were just piggybacking the parent device or (gasp) floating in
   space outside of the device model. We now finally make GPIO chips
   devices. The gpio_chip will create a gpio_device which contains
   a struct device, and this gpio_device struct is kept private.
   Anything that needs to be kept private from the rest of the kernel
   will gradually be moved over to the gpio_device.
 
 - As a result of making the gpio_device a real device, we have added
   resource management, so devm_gpiochip_add_data() will cut down on
   overhead and reduce code lines. A huge slew of patches convert
   almost all drivers in the subsystem to use this.
 
 - Building on making the GPIO a real device, we add the first step
   of a new userspace ABI: the GPIO character device. We take small
   steps here, so we first add a pure *information* ABI and the tool
   "lsgpio" that will list all GPIO devices on the system and all
   lines on these devices. We can now discover GPIOs properly from
   userspace. We still have not come up with a way to actually *use*
   GPIOs from userspace.
 
 - To encourage people to use the character device for the future,
   we have it always-enabled when using GPIO. The old sysfs ABI is
   still opt-in (and can be used in parallel), but is marked as
   deprecated. We will keep it around for the foreseeable future,
   but it will not be extended to cover ever more use cases.
 
 Cleanup:
 
 - Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
   includes. This dates back to when GPIO was an opt-in feature and
   no shared library even existed: just a header file with proper
   prototypes was provided and all semantics were up to the arch to
   implement. These patches make the GPIO chip even more a proper
   device and cleans out leftovers of the old in-kernel API here
   and there. Still some cruft is left but it's very little now.
 
 - There is still some clamping of return values for .get() going
   on, but we now return sane values in the vast majority of drivers
   and the errorpath is sanitized. Some patches for powerpc, blackfin
   and unicore still drop in.
 
 - We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
   implementations to use gpiochip_add_data() and cut down on code
   lines.
 
 - MPC8xxx is converted to use the generic GPIO helpers.
 
 - ATH79 is converted to use the generic GPIO helpers.
 
 New drivers:
 
 - WinSystems WS16C48
 
 - Acces 104-DIO-48E
 
 - F81866 (a F7188x variant)
 
 - Qoric (a MPC8xxx variant)
 
 - TS-4800
 
 - SPI serializers (pisosr): simple 74xx shift registers connected
   to SPI to obtain a dirt-cheap output-only GPIO expander.
 
 - Texas Instruments TPIC2810
 
 - Texas Instruments TPS65218
 
 - Texas Instruments TPS65912
 
 - X-Gene (ARM64) standby GPIO controller
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJW6m24AAoJEEEQszewGV1zUasP/RpTrjRcNI5QFHjudd2oioDx
 R/IljC06Q072ZqVy/MR7QxwhoU8jUnCgKgv4rgMa1OcfHblxC2R1+YBKOUSij831
 E+SYmYDYmoMhN7j5Aslr66MXg1rLdFSdCZWemuyNruAK8bx6cTE1AWS8AELQzzTn
 Re/CPpCDbujLy0ZK2wJHgr9ZkdcBGICtDRCrOR3Kyjpwk/DSZcruK1PDN+VQMI3k
 bJlwgtGenOHINgCq/16edpwj/hzmoJXhTOZXJHI5XVR6czTwb3SvCYACvCkauI/a
 /N7b3quG88b5y0OPQPVxp5+VVl9GyVcv5oGzIfTNat/g5QinShZIT4kVV9r0xu6/
 TQHh1HlXleh+QI3yX0oRv9ztHreMf+vdpw1dhIwLqHqfJ7AWdOGk7BbKjwCrsOoq
 t/qUVFnyvooLpyr53Z5JY8+LqyynHF68G+jUQyHLgTZ0GCE+z+1jqNl1T501n3kv
 3CSlNYxSN/YUBN3cnroAIU/ZWcV4YRdxmOtEWP+7xgcdzTE6s/JHb2fuEfVHzWPf
 mHWtJGy8U0IR4VSSEln5RtjhRr0PAjTHeTOGAmivUnaIGDziTowyUVF+X5hwC77E
 DGTuLVx/Kniv173DK7xNAsUZNAETBa3fQZTgu+RfOpMiM1FZc7tI1rd7K7PjbyCc
 d2M0gcq+d11ITJTxC7OM
 =9AJ4
 -----END PGP SIGNATURE-----

Merge tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull GPIO updates from Linus Walleij:
 "This is the bulk of GPIO changes for kernel v4.6.  There is quite a
  lot of interesting stuff going on.

  The patches to other subsystems and arch-wide are ACKed as far as
  possible, though I consider things like per-arch <asm/gpio.h> as
  essentially a part of the GPIO subsystem so it should not be needed.

  Core changes:

   - The gpio_chip is now a *real device*.  Until now the gpio chips
     were just piggybacking the parent device or (gasp) floating in
     space outside of the device model.

     We now finally make GPIO chips devices.  The gpio_chip will create
     a gpio_device which contains a struct device, and this gpio_device
     struct is kept private.  Anything that needs to be kept private
     from the rest of the kernel will gradually be moved over to the
     gpio_device.

   - As a result of making the gpio_device a real device, we have added
     resource management, so devm_gpiochip_add_data() will cut down on
     overhead and reduce code lines.  A huge slew of patches convert
     almost all drivers in the subsystem to use this.

   - Building on making the GPIO a real device, we add the first step of
     a new userspace ABI: the GPIO character device.  We take small
     steps here, so we first add a pure *information* ABI and the tool
     "lsgpio" that will list all GPIO devices on the system and all
     lines on these devices.

     We can now discover GPIOs properly from userspace.  We still have
     not come up with a way to actually *use* GPIOs from userspace.

   - To encourage people to use the character device for the future, we
     have it always-enabled when using GPIO.  The old sysfs ABI is still
     opt-in (and can be used in parallel), but is marked as deprecated.

     We will keep it around for the foreseeable future, but it will not
     be extended to cover ever more use cases.

  Cleanup:

   - Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
     includes.

     This dates back to when GPIO was an opt-in feature and no shared
     library even existed: just a header file with proper prototypes was
     provided and all semantics were up to the arch to implement.  These
     patches make the GPIO chip even more a proper device and cleans out
     leftovers of the old in-kernel API here and there.

     Still some cruft is left but it's very little now.

   - There is still some clamping of return values for .get() going on,
     but we now return sane values in the vast majority of drivers and
     the errorpath is sanitized.  Some patches for powerpc, blackfin and
     unicore still drop in.

   - We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
     implementations to use gpiochip_add_data() and cut down on code
     lines.

   - MPC8xxx is converted to use the generic GPIO helpers.

   - ATH79 is converted to use the generic GPIO helpers.

  New drivers:

   - WinSystems WS16C48

   - Acces 104-DIO-48E

   - F81866 (a F7188x variant)

   - Qoric (a MPC8xxx variant)

   - TS-4800

   - SPI serializers (pisosr): simple 74xx shift registers connected to
     SPI to obtain a dirt-cheap output-only GPIO expander.

   - Texas Instruments TPIC2810

   - Texas Instruments TPS65218

   - Texas Instruments TPS65912

   - X-Gene (ARM64) standby GPIO controller"

* tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (194 commits)
  Revert "Share upstreaming patches"
  gpio: mcp23s08: Fix clearing of interrupt.
  gpiolib: Fix comment referring to gpio_*() in gpiod_*()
  gpio: pca953x: Fix pca953x_gpio_set_multiple() on 64-bit
  gpio: xgene: Fix kconfig for standby GIPO contoller
  gpio: Add generic serializer DT binding
  gpio: uapi: use 0xB4 as ioctl() major
  gpio: tps65912: fix bad merge
  Revert "gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free"
  gpio: omap: drop dev field from gpio_bank structure
  gpio: mpc8xxx: Slightly update the code for better readability
  gpio: mpc8xxx: Remove *read_reg and *write_reg from struct mpc8xxx_gpio_chip
  gpio: mpc8xxx: Fixup setting gpio direction output
  gpio: mcp23s08: Add support for mcp23s18
  dt-bindings: gpio: altera: Fix altr,interrupt-type property
  gpio: add driver for MEN 16Z127 GPIO controller
  gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free
  gpio: timberdale: Switch to devm_ioremap_resource()
  gpio: ts4800: Add IMX51 dependency
  gpiolib: rewrite gpiodev_add_to_list
  ...
2016-03-17 21:05:32 -07:00
Andre Przywara
96851d391d drivers: pinctrl: add driver for Allwinner A64 SoC
Based on the Allwinner A64 user manual and on the previous sunxi
pinctrl drivers this introduces the pin multiplex assignments for
the ARMv8 Allwinner A64 SoC.
Port A is apparently used for the fixed function DRAM controller, so
the ports start at B here (the manual mentions "n from 1 to 7", so
not starting at 0).

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-03-11 22:46:27 +07:00
Linus Walleij
cc998d8bc7 Linux 4.5-rc5
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJWyN0eAAoJEHm+PkMAQRiGqIAIAKKodaqX5ACJhTRozj3GN5iV
 dDHU/SJQj4nIyJecaCVAJIBa3gvAX6GyY+Jg4JKJ4TKAdR0Hd/3EwOWIR+0+BQIM
 0MqmB0CRLzq42AOQtpDUdwB+OTE8jFQFQd2gFKuQYJJ61ppykCC36OWV0bTfQLSV
 b2esO4Ry6eoQnDMw8oT52ncUIZEvQ2DZE3L6tNDEPD/0je14GWkV1Fx1+X2jb9cB
 diFA2TmaEEXMHNT1NCLSQ+D7QefXV3mFl85leNlFi5QQNy7ZdSh7kvvOodMQ2uAS
 qa9V8Uk6LZYv5O71+Jr5Rmlqh3GxNRCMXu2tlMd2gtw8ApEvBw6XoL5YZYE13Lk=
 =3HMg
 -----END PGP SIGNATURE-----

Merge tag 'v4.5-rc5' into devel

Linux 4.5-rc5
2016-03-10 09:29:25 +07:00
Paul Gortmaker
5ab260aac6 pinctrl: sunxi: make A80 explicitly non-modular
The Kconfig currently controlling compilation of this code is:

drivers/pinctrl/sunxi/Kconfig:config PINCTRL_SUN9I_A80_R
drivers/pinctrl/sunxi/Kconfig:  def_bool MACH_SUN9I

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.

Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-03-09 10:27:25 +07:00
Paul Gortmaker
bcc7619978 pinctrl: sunxi: does not need module.h
This file is not modular, nor is it using modular functions. The
only thing close is the global THIS_MODULE which comes from export.h
so lets replace it appropriately and cut back on the amount of
header stuff we draw in by several thousand lines.

Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-03-09 10:22:47 +07:00
Henry Paulissen
7866f5a0ba pinctrl: sunxi: Change mux setting on PI irq pins
While I was testing irq's on the cubietruck I found a couple of
not working irq pins. Further diving into the problem it opened
up a mess called "manual".

This so called manual (A20 user manual v1.3 dated 2014-10-10) says:

Pin overview:
    Page 237:       EINT26 is on mux 5.
    Page 288:       EINT26 is on mux 6.

The manual is so contradicting that further tests had to be made
to see which of the 2 statements where correct.

This patch is based on actual outcome of these tests and not what
the manual says.

Test procedure used:

Connect a 1 pulse per second (GPS) line to the pin.

echo pin### > /sys/class/gpio/export
echo in > /sys/class/gpio/gpio###/direction
echo rising > /sys/class/gpio/gpio###/edge

Check /proc/interrupts if a irq was attached and if irq's where
received.

Hardware used:
Henry Paulissen: Cubietruck
Andere Przywara: BananaPi M1

Tested-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Henry Paulissen <henry@nitronetworks.nl>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-03-08 16:02:27 +07:00
Henry Paulissen
9c24ef41fe pinctrl: sunxi: Remove non existing irq's
While I was testing irq's on the cubietruck I found a couple of
not working irq pins. Further diving into the problem it opened
up a mess called "manual".

This so called manual (A20 user manual v1.3 dated 2014-10-10) says:

Pin overview:
    Page 233:       EINT12 is on pin PC19 mux6.
    Page 236:       EINT12 is on pin PH12 mux6.

Now, it is a bit strange to have the same IRQ on 2 different pins,
but I guess this could still be possible hardware wise. But then:

Pin registers:
    Page 253:       EINT12 is *not* on pin PC19.
    Page 281:       EINT12 is on pin PH12.

The manual is so contradicting that further tests had to be made
to see which of the 2 statements where correct.

This patch is based on actual outcome of these tests and not what
the manual says.

Test procedure used:

Connect a 1 pulse per second (GPS) line to the pin.

echo pin### > /sys/class/gpio/export
echo in > /sys/class/gpio/gpio###/direction
echo rising > /sys/class/gpio/gpio###/edge

Check /proc/interrupts if a irq was attached and if irq's where
received.

Signed-off-by: Henry Paulissen <henry@nitronetworks.nl>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-03-08 16:00:38 +07:00
Linus Walleij
6cee3821e4 gpio/pinctrl: sunxi: stop poking around in private vars
This kind of hacks disturbs the refactoring of the gpiolib.

The descriptor table belongs to the gpiolib, if we want to know
something about something in it, use or define the proper accessor
functions. Let's add this gpiochip_lins_is_irq() to do what the
sunxi driver is trying at so we can privatize the descriptors
properly.

Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-11 20:29:45 +01:00
Krzysztof Adamski
be2d107f44 pinctrl: sunxi: Use pin number when calling sunxi_pmx_set
sunxi_pmx_set accepts pin number and then calculates offset by
subtracting pin_base from it. sunxi_pinctrl_gpio_get, on the other hand,
gets offset so we have to convert it to pin number so we won't get
negative value in sunxi_pmx_set.

This was only used on A10 so far, where there is only one GPIO chip with
pin_base set to 0 so it didn't matter. However H3 also requires this
workaround but have two pinmux sections, triggering problem for PL port.

Signed-off-by: Krzysztof Adamski <k@japko.eu>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-11 14:30:29 +01:00
Krzysztof Adamski
ba83a11104 pinctrl: sunxi: Add H3 R_PIO controller support
H3 has additional PIO controller similar to what we can find on A23.
It's a 12 pin port, described in H3 Datasheet rev 1.1, pages 345-350.

Signed-off-by: Krzysztof Adamski <k@japko.eu>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-11 14:29:24 +01:00
Krzysztof Adamski
111f2b8732 pinctrl: sunxi: H3 requires irq_read_needs_mux
It seems that on H3, just like on A10, when GPIOs are configured as
external interrupt data registers does not contain their value.  When
value is read, GPIO function must be temporary switched to input for
reads.

Signed-off-by: Krzysztof Adamski <k@japko.eu>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-11 14:29:13 +01:00
Masahiro Yamada
3a42a042f5 pinctrl: sunxi: guard sub-directory with CONFIG_PINCTRL_SUNXI
CONFIG_PINCTRL_SUNXI is more suitable than CONFIG_ARCH_SUNXI
to guard the drivers/pinctrl/sunxi/ directory.
(I renamed CONFIG_PINCTRL_SUNXI_COMMON to CONFIG_PINCTRL_SUNXI.)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-01-28 14:25:50 +01:00
Linus Torvalds
58cf279aca GPIO bulk updates for the v4.5 kernel cycle:
Infrastructural changes:
 
 - In struct gpio_chip, rename the .dev node to .parent to better reflect
   the fact that this is not the GPIO struct device abstraction. We will
   add that soon so this would be totallt confusing.
 
 - It was noted that the driver .get_value() callbacks was
   sometimes reporting negative -ERR values to the gpiolib core, expecting
   them to be propagated to consumer gpiod_get_value() and gpio_get_value()
   calls. This was not happening, so as there was a mess of drivers
   returning negative errors and some returning "anything else than zero"
   to indicate that a line was active. As some would have bit 31 set to
   indicate "line active" it clashed with negative error codes. This is
   fixed by the largeish series clamping values in all drivers with
   !!value to [0,1] and then augmenting the code to propagate error codes
   to consumers. (Includes some ACKed patches in other subsystems.)
 
 - Add a void *data pointer to struct gpio_chip. The container_of() design
   pattern is indeed very nice, but we want to reform the struct gpio_chip
   to be a non-volative, stateless business, and keep states internal to
   the gpiolib to be able to hold on to the state when adding a proper
   userspace ABI (character device) further down the road. To achieve this,
   drivers need a handle at the internal state that is not dependent on
   their struct gpio_chip() so we add gpiochip_add_data() and
   gpiochip_get_data() following the pattern of many other subsystems.
   All the "use gpiochip data pointer" patches transforms drivers to this
   scheme.
 
 - The Generic GPIO chip header has been merged into the general
   <linux/gpio/driver.h> header, and the custom header for that removed.
   Instead of having a separate mm_gpio_chip struct for these generic
   drivers, merge that into struct gpio_chip, simplifying the code and
   removing the need for separate and confusing includes.
 
 Misc improvements:
 
 - Stabilize the way GPIOs are looked up from the ACPI legacy
   specification.
 
 - Incremental driver features for PXA, PCA953X, Lantiq (patches from the
   OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
 
 New drivers:
 
 - Add a GPIO chip to the ALSA SoC AC97 driver.
 
 - Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir, but
   the branch is merged here too to account for infrastructural changes).
 
 - The sx150x driver now supports the sx1502.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJWmsZhAAoJEEEQszewGV1ztq0QAJ1KbNOpmf/s3INkOH4r771Z
 WIrNEsmwwLIAryo8gKNOM0H1zCwhRUV7hIE5jYWgD6JvjuAN6vobMlZAq21j6YpB
 pKgqnI5DuoND450xjb8wSwGQ5NTYp1rFXNmwCrtyTjOle6AAW+Kp2cvVWxVr77Av
 uJinRuuBr9GOKW/yYM1Fw/6EPjkvvhVOb+LBguRyVvq0s5Peyw7ZVeY1tjgPHJLn
 oSZ9dmPUjHEn91oZQbtfro3plOObcxdgJ8vo//pgEmyhMeR8XjXES+aUfErxqWOU
 PimrZuMMy4cxnsqWwh3Dyxo7KSWfJKfSPRwnGwc/HgbHZEoWxOZI1ezRtGKrRQtj
 vubxp5dUBA5z66TMsOCeJtzKVSofkvgX2Wr/Y9jKp5oy9cHdAZv9+jEHV1pr6asz
 Tas97MmmO77XuRI/GPDqVHx8dfa15OIz9s92+Gu64KxNzVxTo4+NdoPSNxkbCILO
 FKn7EmU3D0OjmN2NJ9GAURoFaj3BBUgNhaxacG9j2bieyh+euuUHRtyh2k8zXR9y
 8OnY1UOrTUYF8YIq9pXZxMQRD/lqwCNHvEjtI6BqMcNx4MptfTL+FKYUkn/SgCYk
 QTNV6Ui+ety5D5aEpp5q0ItGsrDJ2LYSItsS+cOtMy2ieOxbQav9NWwu7eI3l5ly
 gwYTZjG9p9joPXLW0E3g
 =63rR
 -----END PGP SIGNATURE-----

Merge tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull GPIO updates from Linus Walleij:
 "Here is the bulk of GPIO changes for v4.5.

  Notably there are big refactorings mostly by myself, aimed at getting
  the gpio_chip into a shape that makes me believe I can proceed to
  preserve state for a proper userspace ABI (character device) that has
  already been proposed once, but resulted in the feedback that I need
  to go back and restructure stuff.  So I've been restructuring stuff.
  On the way I ran into brokenness (return code from the get_value()
  callback) and had to fix it.  Also, refactored generic GPIO to be
  simpler.

  Some of that is still waiting to trickle down from the subsystems all
  over the kernel that provide random gpio_chips, I've touched every
  single GPIO driver in the kernel now, oh man I didn't know I was
  responsible for so much...

  Apart from that we're churning along as usual.

  I took some effort to test and retest so it should merge nicely and we
  shook out a couple of bugs in -next.

  Infrastructural changes:

   - In struct gpio_chip, rename the .dev node to .parent to better
     reflect the fact that this is not the GPIO struct device
     abstraction.  We will add that soon so this would be totallt
     confusing.

   - It was noted that the driver .get_value() callbacks was sometimes
     reporting negative -ERR values to the gpiolib core, expecting them
     to be propagated to consumer gpiod_get_value() and gpio_get_value()
     calls.  This was not happening, so as there was a mess of drivers
     returning negative errors and some returning "anything else than
     zero" to indicate that a line was active.  As some would have bit
     31 set to indicate "line active" it clashed with negative error
     codes.  This is fixed by the largeish series clamping values in all
     drivers with !!value to [0,1] and then augmenting the code to
     propagate error codes to consumers.  (Includes some ACKed patches
     in other subsystems.)

   - Add a void *data pointer to struct gpio_chip.  The container_of()
     design pattern is indeed very nice, but we want to reform the
     struct gpio_chip to be a non-volative, stateless business, and keep
     states internal to the gpiolib to be able to hold on to the state
     when adding a proper userspace ABI (character device) further down
     the road.  To achieve this, drivers need a handle at the internal
     state that is not dependent on their struct gpio_chip() so we add
     gpiochip_add_data() and gpiochip_get_data() following the pattern
     of many other subsystems.  All the "use gpiochip data pointer"
     patches transforms drivers to this scheme.

   - The Generic GPIO chip header has been merged into the general
     <linux/gpio/driver.h> header, and the custom header for that
     removed.  Instead of having a separate mm_gpio_chip struct for
     these generic drivers, merge that into struct gpio_chip,
     simplifying the code and removing the need for separate and
     confusing includes.

  Misc improvements:

   - Stabilize the way GPIOs are looked up from the ACPI legacy
     specification.

   - Incremental driver features for PXA, PCA953X, Lantiq (patches from
     the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48

  New drivers:

   - Add a GPIO chip to the ALSA SoC AC97 driver.

   - Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir,
     but the branch is merged here too to account for infrastructural
     changes).

   - The sx150x driver now supports the sx1502"

* tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits)
  gpio: generic: make bgpio_pdata always visible
  gpiolib: fix chip order in gpio list
  gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
  gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs()
  gpio: brcmstb: Allow building driver for BMIPS_GENERIC
  gpio: brcmstb: Set endian flags for big-endian MIPS
  gpio: moxart: fix build regression
  gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs()
  leds: pca9532: use gpiochip data pointer
  leds: tca6507: use gpiochip data pointer
  hid: cp2112: use gpiochip data pointer
  bcma: gpio: use gpiochip data pointer
  avr32: gpio: use gpiochip data pointer
  video: fbdev: via: use gpiochip data pointer
  gpio: pch: Optimize pch_gpio_get()
  Revert "pinctrl: lantiq: Implement gpio_chip.to_irq"
  pinctrl: nsp-gpio: use gpiochip data pointer
  pinctrl: vt8500-wmt: use gpiochip data pointer
  pinctrl: exynos5440: use gpiochip data pointer
  pinctrl: at91-pio4: use gpiochip data pointer
  ...
2016-01-17 12:32:01 -08:00
Linus Walleij
88057d6e4a pinctrl: sunxi: use gpiochip data pointer
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-01-05 14:15:03 +01:00
Linus Walleij
39e24ac3c3 pinctrl: sunxi: Be sure to clamp return value
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-12-26 22:28:41 +01:00
Maxime Ripard
0eccc9cb4c pinctrl: sunxi: Add A80 special pin controller
Like the previous designs, the A80 has a special pin controller for the
critical pins, like the PMIC bus.

Add a driver for this controller.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wens: Add A80 compatible strings to bindings doc; fix pin function
       names based on v1.3 datasheet; constify of_device_id table]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-12-22 10:28:11 +01:00
Jens Kuske
e87623cb3b pinctrl: sunxi: Add H3 PIO controller support
The H3 uses the same pin controller as previous SoC's from Allwinner.
Add support for the pins controlled by the main PIO controller.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-12-11 10:15:33 +01:00
Linus Walleij
58383c7842 gpio: change member .dev to .parent
The name .dev in a struct is normally reserved for a struct device
that is let us say a superclass to the thing described by the struct.
struct gpio_chip stands out by confusingly using a struct device *dev
to point to the parent device (such as a platform_device) that
represents the hardware. As we want to give gpio_chip:s real devices,
this is not working. We need to rename this member to parent.

This was done by two coccinelle scripts, I guess it is possible to
combine them into one, but I don't know such stuff. They look like
this:

@@
struct gpio_chip *var;
@@
-var->dev
+var->parent

and:

@@
struct gpio_chip var;
@@
-var.dev
+var.parent

and:

@@
struct bgpio_chip *var;
@@
-var->gc.dev
+var->gc.parent

Plus a few instances of bgpio that I couldn't figure out how
to teach Coccinelle to rewrite.

This patch hits all over the place, but I *strongly* prefer this
solution to any piecemal approaches that just exercise patch
mechanics all over the place. It mainly hits drivers/gpio and
drivers/pinctrl which is my own backyard anyway.

Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-11-19 09:24:35 +01:00
Linus Torvalds
e86328c489 This is the bulk of GPIO changes for v4.4:
GPIO core:
 - Define and handle flags for open drain/open collector
   and open source/open emitter, also know as "single-ended"
   configurations.
 - Generic request/free operations that handle calling out
   to the (optional) pin control backend.
 - Some refactoring related to an ABI change that did not
   happen, yet provide useful.
 - Added a real-time compliance checklist. Many GPIO chips
   have irqchips, and need to think this over with the RT
   patches going upstream.
 - Restructure, fix and clean up Kconfig menus a bit.
 
 New drivers:
 - New driver for AMD Promony.
 - New driver for ACCES 104-IDIO-16, a port-mapped I/O
   card, ISA-style. Very retro.
 
 Subdriver changes:
 - OMAP changes to handle real time requirements.
 - Handle trigger types for edge and level IRQs on PL061
   properly. As this hardware is very common it needs to
   set a proper example for others to follow.
 - Some container_of() cleanups.
 - Delete the unused MSM driver in favor of the driver that
   is embedded inside the pin control driver.
 - Cleanup of the ath79 GPIO driver used by many, many
   OpenWRT router targets.
 - A consolidated IT87xx driver replacing the earlier
   very specific IT8761e driver.
 - Handle the TI TCA9539 in the PCA953x driver. Also
   handle ACPI devices in this subdriver.
 - Drop xilinx arch dependencies as these FPGAs seem to
   profilate over a few different architectures. MIPS and
   ARM come to mind.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJWNz3qAAoJEEEQszewGV1zKlAP/R+mVoQHyfDFurChDzuWQjZK
 T4eDiFGTHr/MUDP9I0jINF400SfEm3ajm3aoPvKc6fA2d7oLNB7TzyUxjDsQV4h8
 NsCJ9IYD9xYgF6SDovPYPZ6SkRJYimDrwjD/DUSR8ijisVzJwYCyEGznelWKnQMo
 Fcw4kOTMrW0034ZT4nGH4kSgIzNAMcecazaaqLisniYZ/4Ozk1CQsrBK1gCO/kr8
 Hh3N/mN4TBvOyIuD7lmN5PnWuJo641rplcWErjxUZYvqEddSfAnpasfAcXMkZ4gM
 jOK+l7VIycxOAn+EJwqjyVPJ0gDPPaMwB836gogzNraO2SYd/R2JvyI2zyTogmdW
 MNwsKwP2b/ma/h0A/JBDFmcMiJwA2QHHgylLrB+vfWAP9o2nJv++Op1/q8ktVR+1
 EgEk9StVvnYqC86DJhYbUbMmX7TorRwPoUo/5Z6C/viyZzOagZge0vYKYTQS99Pq
 B+2aH7pMPLooAdU/cyYy8J20mxQ4RaHoy+TCe0RMRhxnRi9CnnnYNHbZDVdHISpr
 OSfZKSM40DbAAs7UNxIgPXM1qSzia23tgzZEdh5qwQtZBTC6fWr/1xOrTpFW2wY6
 VxqgP/OX23BzJQE4YDnOHLIj8GX0MLqXr7pl2+KBcHO9xvPS6Qj8fFsLEVatCwX0
 Caify6KIbbgMWcVmut/6
 =LDCr
 -----END PGP SIGNATURE-----

Merge tag 'gpio-v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull GPIO updates from Linus Walleij:
 "Here is the bulk of GPIO changes for the v4.4 development cycle.

  The only changes hitting outside drivers/gpio are in the pin control
  subsystem and these seem to have settled nicely in linux-next.

  Development mistakes and catfights are nicely documented in the
  reverts as you can see.  The outcome of the ABI fight is that we're
  working on a chardev ABI for GPIO now, where hope to show results for
  the v4.5 kernel.

  Summary of changes:

  GPIO core:
   - Define and handle flags for open drain/open collector and open
     source/open emitter, also know as "single-ended" configurations.
   - Generic request/free operations that handle calling out to the
     (optional) pin control backend.
   - Some refactoring related to an ABI change that did not happen, yet
     provide useful.
   - Added a real-time compliance checklist.  Many GPIO chips have
     irqchips, and need to think this over with the RT patches going
     upstream.
   - Restructure, fix and clean up Kconfig menus a bit.

  New drivers:
   - New driver for AMD Promony.
   - New driver for ACCES 104-IDIO-16, a port-mapped I/O card,
     ISA-style.  Very retro.

  Subdriver changes:
   - OMAP changes to handle real time requirements.
   - Handle trigger types for edge and level IRQs on PL061 properly.  As
     this hardware is very common it needs to set a proper example for
     others to follow.
   - Some container_of() cleanups.
   - Delete the unused MSM driver in favor of the driver that is
     embedded inside the pin control driver.
   - Cleanup of the ath79 GPIO driver used by many, many OpenWRT router
     targets.
   - A consolidated IT87xx driver replacing the earlier very specific
     IT8761e driver.
   - Handle the TI TCA9539 in the PCA953x driver.  Also handle ACPI
     devices in this subdriver.
   - Drop xilinx arch dependencies as these FPGAs seem to profilate over
     a few different architectures.  MIPS and ARM come to mind"

* tag 'gpio-v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (57 commits)
  gpio: fix up SPI submenu
  gpio: drop surplus I2C dependencies
  gpio: drop surplus X86 dependencies
  gpio: dt-bindings: document the official use of "ngpios"
  gpio: MAINTAINERS: Add an entry for the ATH79 GPIO driver
  gpio / ACPI: Allow shared GPIO event to be read via operation region
  gpio: group port-mapped I/O drivers in a menu
  gpio: Add ACCES 104-IDIO-16 driver maintainer entry
  gpio: zynq: Document interrupt-controller DT binding
  gpio: xilinx: Drop architecture dependencies
  gpio: generic: Revert to old error handling in bgpio_map
  gpio: add a real time compliance notes
  Revert "gpio: add a real time compliance checklist"
  gpio: Add GPIO support for the ACCES 104-IDIO-16
  gpio: driver for AMD Promontory
  gpio: xlp: Convert to use gpiolib irqchip helpers
  gpio: add a real time compliance checklist
  gpio/xilinx: enable for MIPS
  gpiolib: Add and use OF_GPIO_SINGLE_ENDED flag
  gpiolib: Split GPIO flags parsing and GPIO configuration
  ...
2015-11-02 12:59:12 -08:00
Linus Torvalds
bc9d8c20ff This is the big bulk of pin control changes for the
v4.4 kernel development cycle:
 
 Infrastructure:
 - Doug Anderson wrote a patch adding an "init" state
   different from the "default" state for pin control
   state handling in the core framework. This is applied
   before the driver's probe() call if defined and takes
   precedence over "default". If both are defined, "init"
   will be applied *before* probe() and "default" will be
   applied *after* probe().
 
 Significant subdriver improvements:
 - SH PFC is switched to getting GPIO ranges from the
   device tree ranges property on DT platforms.
 - Got rid of CONFIG_ARCH_SHMOBILE_LEGACY, we are all
   modernized.
 - Got rid of SH PFC hardcoded IRQ numbers.
 - Allwinner sunxi external interrupt through the "r"
   controller.
 - Moved the Cygnus driver to use DT-provided GPIO
   ranges.
 
 New drivers:
 - Atmel PIO4 pin controller for the SAMA4D2 family
 
 New subdrivers:
 - Rockchip RK3036 subdriver
 - Renesas SH PFC R8A7795 subdriver
 - Allwinner sunxi A83T PIO subdriver
 - Freescale i.MX7d iomux lpsr subdriver
 - Marvell Berlin BG4CT subdriver
 - SiRF Atlas 7 step B SoC subdriver
 - Intel Broxton SoC subdriver
 
 Apart from this, the usual slew if syntactic and semantic
 fixes.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJWNzaFAAoJEEEQszewGV1zth0QAIWBhrEFeZNw3yewSwtawBin
 Q+5hxxld7YWeYykK/phRw+nru+tRmRKd72uZbiA/OHDFmXdlF7ecQC+D2ByAT/a3
 /d61BPtuT0tzmiZTmYSdbivBZzXjs9UrbEsGe2MXgf2WJuzZU/2EiQwCxklDfiX6
 BWa0lcL9+ikVRh53xGoEps/5KVOkXSlPDq/twXp6Trd6B1k+opPqKHf7UNxb0BvK
 0QoNPDYBTb93Z9iIItQdAGNCD/JMllywpUcqK+tPdQoRdrqlAcdRlUdXI7rdtvGw
 O3O2/MTBrGI7pxCNxBPGi9+niM6qtLrwKeQx8iIe0ieTIrUCCdg3vftUXctxXHkC
 +GxKLQGO/aMqW/4O8J+voAOD5HiGc+heoJsQEWoysoooWos/IxVJiiCKy5RNTk7g
 ECbzQvu7kbwTnwNXbxAc5ocdwhQ6HpJe2X2S52zTpDscfK8HcOow0hmf9m2EI4hV
 ikf47WJQIN9zunJloiJ3oZveK0Eytx1hH/47gcFRwr0KV/DK0KngvxnPWlB2nzlc
 pggkVnkHXczCyqBfDhZomILnTK2aDt6RKUZhz4w1s8ezK2EDn8Vvt3Qm7wOIeWvR
 xiY7XVoO+AYOywuFsbNxkt28Y8h5yQxu/AV6/rYSn+NYCZcLxKbcrVEiY2N6ecCA
 x74epIdnjA8F7S3Xp14q
 =0t3B
 -----END PGP SIGNATURE-----

Merge tag 'pinctrl-v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control updates from Linus Walleij:
 "This is the big bulk of pin control changes for the v4.4 kernel
  development cycle.  Development pace is high in pin control again this
  merge window.  28 contributors, 83 patches.

  It hits a few sites outside the pin control subsystem:

   - Device tree bindings in Documentation (as usual)
   - MAINTAINERS
   - drivers/base/* for the "init" state handling by Doug Anderson.
     This has been ACKed by Greg.
   - drivers/usb/renesas_usbhs/rcar2.c, for a dependent Renesas change
     in the USB subsystem.  This has been ACKed by both Greg and Felipe.
   - arch/arm/boot/dts/sama5d2.dtsi - this should ideally have gone
     through the ARM SoC tree but ended up here.

  This time I am using Geert Uytterhoeven as submaintainer for SH PFC
  since the are three-four people working in parallel with new Renesas
  ASICs.

  Summary of changes:

  Infrastructure:

   - Doug Anderson wrote a patch adding an "init" state different from
     the "default" state for pin control state handling in the core
     framework.  This is applied before the driver's probe() call if
     defined and takes precedence over "default".  If both are defined,
     "init" will be applied *before* probe() and "default" will be
     applied *after* probe().

  Significant subdriver improvements:

   - SH PFC is switched to getting GPIO ranges from the device tree
     ranges property on DT platforms.
   - Got rid of CONFIG_ARCH_SHMOBILE_LEGACY, we are all modernized.
   - Got rid of SH PFC hardcoded IRQ numbers.
   - Allwinner sunxi external interrupt through the "r" controller.
   - Moved the Cygnus driver to use DT-provided GPIO ranges.

  New drivers:

   - Atmel PIO4 pin controller for the SAMA4D2 family

  New subdrivers:

   - Rockchip RK3036 subdriver
   - Renesas SH PFC R8A7795 subdriver
   - Allwinner sunxi A83T PIO subdriver
   - Freescale i.MX7d iomux lpsr subdriver
   - Marvell Berlin BG4CT subdriver
   - SiRF Atlas 7 step B SoC subdriver
   - Intel Broxton SoC subdriver

  Apart from this, the usual slew if syntactic and semantic fixes"

* tag 'pinctrl-v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (81 commits)
  pinctrl: pinconf: remove needless loop
  pinctrl: uniphier: guard uniphier directory with CONFIG_PINCTRL_UNIPHIER
  pinctrl: zynq: fix UTF-8 errors
  pinctrl: zynq: Initialize early
  pinctrl: at91: add missing of_node_put
  pinctrl: tegra-xusb: Correct lane mux options
  pinctrl: intel: Add Intel Broxton pin controller support
  pinctrl: intel: Allow requesting pins which are in ACPI mode as GPIOs
  pinctrl: intel: Add support for multiple GPIO chips sharing the interrupt
  drivers/pinctrl: Add the concept of an "init" state
  pinctrl: uniphier: set input-enable before pin-muxing
  pinctrl: cygnus: Add new compatible string for gpio controller driver
  pinctrl: cygnus: Remove GPIO to Pinctrl pin mapping from driver
  pinctrl: cygnus: Optional DT property to support pin mappings
  pinctrl: sunxi: Add irq pinmuxing to sun6i "r" pincontroller
  pinctrl: sunxi: Fix irq_of_xlate for the r_pio pinctrl block
  pinctrl: sh-pfc: Remove obsolete r8a7778 platform_device_id entry
  pinctrl: sh-pfc: Remove obsolete r8a7779 platform_device_id entry
  pinctrl: sh-pfc: Stop including <linux/platform_data/gpio-rcar.h>
  usb: renesas_usbhs: Remove unneeded #include <linux/platform_data/gpio-rcar.h>
  ...
2015-11-02 12:30:39 -08:00
Hans de Goede
3f84ccf62c pinctrl: sunxi: Add irq pinmuxing to sun6i "r" pincontroller
Add pinmuxing for external interrupt functionality through the
sun6i "r" pincontroller.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-23 10:13:30 +02:00
Hans de Goede
8297992cad pinctrl: sunxi: Fix irq_of_xlate for the r_pio pinctrl block
The r_pio gpio / pin controller has a pin_base of non 0, we need to
adjust for this before calling sunxi_pinctrl_desc_find_function_by_pin.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-23 10:11:34 +02:00
Jonas Gorski
98c85d583a pinctrl: replace trivial implementations of gpio_chip request/free
Replace all trivial request/free callbacks that do nothing but call into
pinctrl code with the generic versions.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-16 22:20:21 +02:00
Vishnu Patekar
4730f33f0d pinctrl: sunxi: add allwinner A83T PIO controller support
Allwinner A83T soc port controller has 8 ports.
It has 3 IRQ banks namely PB, PG, PH.
Pinmuxing are different for some pins as compared to
sun8i A23 and A33.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-02 04:09:44 -07:00
Javier Martinez Canillas
5c99c0ffa4 pinctrl: sunxi: Remove unneeded semicolon
It's not needed an is just creating a null statement, so remove it.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-02 04:06:47 -07:00
Hans de Goede
d50a9e1b6d pinctrl: sun5i: Fix a10s pwm1 pinctrl mapping
The comment for PG14 mux setting 3 already correctly states that this
muxes PG13 to pwm1, but the text ascociated with it said uart3, fix this.

Note that we use "pwm" rather then "pwm1" to be consistent with pwm0
where the mux setting is also simply called "pwm" and to be consistent
with sun4i/sun7i which do the same.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-02 04:06:01 -07:00
Thomas Gleixner
bd0b9ac405 genirq: Remove irq argument from irq flow handlers
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.

Remove the argument.

Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
2015-09-16 15:47:51 +02:00
Thomas Gleixner
b9a5ec33e3 pinctrl: sunxi: Use irq_set_chip_handler_name_locked()
__irq_set_chip_handler_name_locked() is about to be replaced. Use
irq_set_chip_handler_name_locked() instead.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
2015-09-16 12:42:49 +02:00
Marcus Cooper
8152d8cc59 pinctrl: sun4i: add spdif to pin description.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-08-13 16:03:21 +02:00
Maxime Ripard
d8323c6b03 pinctrl: sunxi: Add custom irq_domain_ops
The current interrupt parsing code was working by accident, because the
default was actually parsing the first node of interrupts.

While that was mostly working (and the flags were actually ignored), this
binding has never been documented, and doesn't work with SoCs that have
multiple interrupt banks anyway.

Add a proper interrupt xlate function, that uses the same description than
the GPIOs (<bank> <pin> <flags>), that will make things less confusing.

The EINT number will still be used as the hwirq number, but won't be
exposed through the DT.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-07-27 14:56:30 +02:00
Maxime Ripard
fb5b778808 pinctrl: sunxi: Add irq_chip name
In order to ease the debugging, add a name to the irq_chips.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-07-27 14:05:16 +02:00
Maxime Ripard
a0d6de9bdf pinctrl: sunxi: Use common functions to change irq_chip and handler
The current code uses some custom variable affectations, while we have
common functions to do exactly that. Move to the common functions.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-07-27 14:05:04 +02:00
Thomas Gleixner
eeef97b182 pinctrl/sunxi: Prepare sunxi_pinctrl_irq_handler for irq argument removal
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.

Search and update was done with coccinelle and the invaluable help of
Julia Lawall.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
2015-07-17 21:56:23 +02:00
Jiang Liu
5663bb27de pinctrl: Use irq_desc_get_xxx() to avoid redundant lookup of irq_desc
Use irq_desc_get_xxx() to avoid redundant lookup of irq_desc while we
already have a pointer to corresponding irq_desc.

Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2015-07-17 21:56:20 +02:00
Linus Torvalds
d5fb82137b Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
 "This contains:

   - a series of fixes for interrupt drivers to prevent a potential race
     when installing a chained interrupt handler

   - a fix for cpumask pointer misuse

   - a fix for using the wrong interrupt number from struct irq_data

   - removal of unused code and outdated comments

   - a few new helper functions which allow us to cleanup the interrupt
     handling code further in 4.3

   I decided against doing the cleanup at the end of this merge window
   and rather do the preparatory steps for 4.3, so we can run the final
   ABI change at the end of the 4.3 merge window with less risk"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
  ARM/LPC32xx: Use irq not hwirq for __irq_set_handler_locked()
  genirq: Implement irq_set_handler_locked()/irq_set_chip_handler_name_locked()
  genirq: Introduce helper irq_desc_get_irq()
  genirq: Remove irq_node()
  genirq: Clean up outdated comments related to include/linux/irqdesc.h
  mn10300: Fix incorrect use of irq_data->affinity
  MIPS/ralink: Fix race in installing chained IRQ handler
  MIPS/pci: Fix race in installing chained IRQ handler
  MIPS/ath25: Fix race in installing chained IRQ handler
  MIPS/ath25: Fix race in installing chained IRQ handler
  m68k/psc: Fix race in installing chained IRQ handler
  avr32/at32ap: Fix race in installing chained IRQ handler
  sh/intc: Fix race in installing chained IRQ handler
  sh/intc: Fix potential race in installing chained IRQ handler
  pinctrl/sun4i: Fix race in installing chained IRQ handler
  pinctrl/samsung: Fix race in installing chained IRQ handler
  pinctrl/samsung: Fix race in installing chained IRQ handler
  pinctrl/exynos: Fix race in installing chained IRQ handler
  pinctrl/st: Fix race in installing chained IRQ handler
  pinctrl/adi2: Fix race in installing chained IRQ handler
  ...
2015-07-01 15:19:35 -07:00
Thomas Gleixner
ef80e87d20 pinctrl/sun4i: Fix race in installing chained IRQ handler
Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().

Search and conversion was done with coccinelle:

@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
-   BUG();
|
-irq_set_chained_handler(E1, E3);
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);

@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
-   BUG();
...
|
-irq_set_chained_handler(E1, E3);
...
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);

Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Fan Wu <fwu@marvell.com>
Cc: abdoulaye berthe <berthe.ab@gmail.com>
Cc: Alexandre Courbot <acourbot@nvidia.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
2015-06-25 11:57:17 +02:00
Masahiro Yamada
323de9efdf pinctrl: make pinctrl_register() return proper error code
Currently, pinctrl_register() just returns NULL on error, so the
callers can not know the exact reason of the failure.

Some of the pinctrl drivers return -EINVAL, some -ENODEV, and some
-ENOMEM on error of pinctrl_register(), although the error code
might be different from the real cause of the error.

This commit reworks pinctrl_register() to return the appropriate
error code and modifies all of the pinctrl drivers to use IS_ERR()
for the error checking and PTR_ERR() for getting the error code.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Ray Jui <rjui@broadcom.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Acked-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-06-10 14:49:52 +02:00
Vishnu Patekar
7164873e7c pinctrl: sunxi: Add allwinner A33 PIO controller support
A33 PIO has 7 ports which starts from PB and has two interrupt ports.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-06-04 10:32:11 +02:00
Fabio Estevam
3944e7b78c pinctrl: Remove .owner field
platform_driver does not need to set the owner field, as it will be
populated by the driver core, so just remove it.

The semantic patch that makes this change is available
in scripts/coccinelle/api/platform_no_drv_owner.cocci.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-06-04 10:12:42 +02:00
Linus Torvalds
07e492eb89 This is the bulk of pin control changes for the v4.1 development
cycle:
 
 New drivers:
   - Intel Sunrisepoint
   - AMD KERNCZ GPIO
   - Broadcom Cygnus IOMUX
 
 New subdrivers:
   - Marvell MVEBU Armada 39x SoCs
   - Samsung Exynos 5433
   - nVidia Tegra 210
   - Mediatek MT8135
   - Mediatek MT8173
   - AMLogic Meson8b
   - Qualcomm PM8916
 
 On top of this cleanups and development history for the above
 drivers as issues were fixed after merging.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJVLSiSAAoJEEEQszewGV1z/nMP/jXyxCb8THuAyCFkJoY+Hgzz
 dj3eMt+TPPyqt6lG3WODq/lQFxEdE28TqHYf2eGVdpriCpuyecFxyf9MPzY3P60E
 v6XfzIeUOIGovw781qsg9TxJAZ0C+DLmNgpS8kWhnK7Igs3EJrRcz5Zz00F32olv
 1dojVIQF6Nsn3M2Cc6bzF2wkJre3tLsUT7KXGZw4e3yA0K1XMZI3jYYXZ25GgLW0
 CpZ1vKdKgwuBsgV5waJ8XZuFMqo3FRhjcD/f8ubk5hhMK6Wx6gszBcrLKVlkbz+2
 XJzhn5tZSupSKmBtl0gCzP7pgVc0JeV8P12hHv6imT82rCU0YGBidNX2s3GrscnF
 Nfwpw/BsaOXcu9CttI5LndvDlvCH2hUAal6i4IghiL5sRzlcW4jUoWHkIa8e6dHe
 e/zjJSo7tXrWio30Dl6++qklcDimP3sbaaFseENhLUSl7hDGJ09Tx8yxEOFN3PX6
 29i7ZC+ifZFzS30E3E+MOlFrxp3MB7j/z/ig3HL7XYr/TTiCKMNbKJNOlmGEfiTV
 VI3GvTAJgt/1U+AOJI7a5xrxivaGL5GWXuoonQHY1gPrvjqkL54w4j+XBpj4tXIV
 LBh6AS6G6AJDUOEU00EroCxOt1FPMW24zQvTKP18sgXsKWqHTIKT9B5RZbDXM9D7
 pLfOIy0H1RWdQGvGgK7X
 =MGqe
 -----END PGP SIGNATURE-----

Merge tag 'pinctrl-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pincontrol updates from Linus Walleij:
 "This is the bulk of pin control changes for the v4.1 development
  cycle.  Nothing really exciting this time: we basically added a few
  new drivers and subdrivers and stabilized them in linux-next.  Some
  cleanups too.  With sunrisepoint Intel has a real fine fully featured
  pin control driver for contemporary hardware, and the AMD driver is
  also for large deployments.  Most of the others are ARM devices.

  New drivers:
    - Intel Sunrisepoint
    - AMD KERNCZ GPIO
    - Broadcom Cygnus IOMUX

  New subdrivers:
    - Marvell MVEBU Armada 39x SoCs
    - Samsung Exynos 5433
    - nVidia Tegra 210
    - Mediatek MT8135
    - Mediatek MT8173
    - AMLogic Meson8b
    - Qualcomm PM8916

  On top of this cleanups and development history for the above drivers
  as issues were fixed after merging"

* tag 'pinctrl-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (71 commits)
  pinctrl: sirf: move sgpio lock into state container
  pinctrl: Add support for PM8916 GPIO's and MPP's
  pinctrl: bcm2835: Fix support for threaded level triggered IRQs
  sh-pfc: r8a7790: add EtherAVB pin groups
  pinctrl: Document "function" + "pins" pinmux binding
  pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support
  pinctrl: fsl: imx: Check for 0 config register
  pinctrl: Add support for Meson8b
  documentation: Extend pinctrl docs for Meson8b
  pinctrl: Cleanup Meson8 driver
  Fix inconsistent spinlock of AMD GPIO driver which can be recognized by static analysis tool smatch. Declare constant Variables with Sparse's suggestion.
  pinctrl: at91: convert __raw to endian agnostic IO
  pinctrl: constify of_device_id array
  pinctrl: pinconf-generic: add dt node names to error messages
  pinctrl: pinconf-generic: scan also referenced phandle node
  pinctrl: mvebu: add suspend/resume support to Armada XP pinctrl driver
  pinctrl: st: Display pin's function when printing pinctrl debug information
  pinctrl: st: Show correct pin direction also in GPIO mode
  pinctrl: st: Supply a GPIO get_direction() call-back
  pinctrl: st: Move st_get_pio_control() further up the source file
  ...
2015-04-14 17:58:15 -07:00
Fabian Frederick
baa9946e32 pinctrl: constify of_device_id array
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-27 09:58:35 +01:00
Hans de Goede
ef6d24cc7f pinctrl: sun4i: GPIOs configured as irq must be set to input before reading
On sun4i-a10, when GPIOs are configured as external interrupt the value for
them in the data register does not seem to get updated, so set their mux to
input (and restore afterwards) when reading the pin.

Missed edges seem to be buffered, so this does not introduce a race
condition.

I've also tested this on sun5i-a13 and sun7i-a20 and those do not seem to
be affected, the input value representation in the data register does seem
to correctly get updated to the actual pin value while in irq mode there.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-18 10:56:46 +01:00
Hans de Goede
47cf4b326c pinctrl: sun6i: Add A31s pinctrl support
The A31s is a stripped down version of the A31, as such it is missing some
pins and some functions on some pins.

The new pinctrl-sun6i-a31s.c this commit adds is a copy of pinctrl-sun6i-a31s.c
with the missing pins and functions removed.

Note there is no a31s specific version of pinctrl-sun6i-a31-r.c, as the
prcm pins are identical between the A31 and the A31s.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-01-14 14:21:52 +01:00
Hans de Goede
c5abe62b76 pinctrl: sun6i: Add some missing functions
While working on pinctrl for the A31s, I noticed that function 4 of
PA15 - PA18 was missing, add these.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-01-14 14:21:52 +01:00
Linus Torvalds
e6b5be2be4 Driver core patches for 3.19-rc1
Here's the set of driver core patches for 3.19-rc1.
 
 They are dominated by the removal of the .owner field in platform
 drivers.  They touch a lot of files, but they are "simple" changes, just
 removing a line in a structure.
 
 Other than that, a few minor driver core and debugfs changes.  There are
 some ath9k patches coming in through this tree that have been acked by
 the wireless maintainers as they relied on the debugfs changes.
 
 Everything has been in linux-next for a while.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
 53kAoLeteByQ3iVwWurwwseRPiWa8+MI
 =OVRS
 -----END PGP SIGNATURE-----

Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core update from Greg KH:
 "Here's the set of driver core patches for 3.19-rc1.

  They are dominated by the removal of the .owner field in platform
  drivers.  They touch a lot of files, but they are "simple" changes,
  just removing a line in a structure.

  Other than that, a few minor driver core and debugfs changes.  There
  are some ath9k patches coming in through this tree that have been
  acked by the wireless maintainers as they relied on the debugfs
  changes.

  Everything has been in linux-next for a while"

* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
  Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
  fs: debugfs: add forward declaration for struct device type
  firmware class: Deletion of an unnecessary check before the function call "vunmap"
  firmware loader: fix hung task warning dump
  devcoredump: provide a one-way disable function
  device: Add dev_<level>_once variants
  ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
  ath: use seq_file api for ath9k debugfs files
  debugfs: add helper function to create device related seq_file
  drivers/base: cacheinfo: remove noisy error boot message
  Revert "core: platform: add warning if driver has no owner"
  drivers: base: support cpu cache information interface to userspace via sysfs
  drivers: base: add cpu_device_create to support per-cpu devices
  topology: replace custom attribute macros with standard DEVICE_ATTR*
  cpumask: factor out show_cpumap into separate helper function
  driver core: Fix unbalanced device reference in drivers_probe
  driver core: fix race with userland in device_add()
  sysfs/kernfs: make read requests on pre-alloc files use the buffer.
  sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
  fs: sysfs: return EGBIG on write if offset is larger than file size
  ...
2014-12-14 16:10:09 -08:00
Linus Torvalds
980f3c344f This is the bulk of GPIO changes for the v3.19 series:
- A new API that allows setting more than one GPIO at the
   time. This is implemented for the new descriptor-based
   API only and makes it possible to e.g. toggle a clock and
   data line at the same time, if the hardware can do this
   with a single register write. Both consumers and drivers
   need new calls, and the core will fall back to driving
   individual lines where needed. Implemented for the MPC8xxx
   driver initially.
 - Patched the mdio-mux-gpio and the serial mctrl driver
   that drives modems to use the new multiple-setting API
   to set several signals simultaneously.
 - Get rid of the global GPIO descriptor array, and instead
   allocate descriptors dynamically for each GPIO on a certain
   GPIO chip. This moves us closer to getting rid of the
   limitation of using the global, static GPIO numberspace.
 - New driver and device tree bindings for 74xx ICs.
 - New driver and device tree bindings for the VF610 Vybrid.
 - Support the RCAR r8a7793 and r8a7794.
 - Guidelines for GPIO device tree bindings trying to get
   things a bit more strict with the advent of combined
   device properties.
 - Suspend/resume support for the MVEBU driver.
 - A slew of minor fixes and improvements.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJUjgQ7AAoJEEEQszewGV1zuJ8P+wamlDNhJbsgqXPcSCZZFgeP
 1O22VRYqoo/i8mAzNCRi2h6NogO9Da6rCRhHdH35TsuNzIbusHE+btMukj248qJ7
 WYOf25I0ImyUP8kulogW4/+7lYibRLHnN2BSLuAkApofmxDvODPS1KNWHulcOcxl
 VaVsA8wvFzQO1s1Wjv94ctVfs5rqk7mBfPwk61zHuLeETecmKg0e52p0Uzqlq6gi
 UKi9uK3sjQ7kI/+xa+qDrF9GRwRR22oJfD/9zNj8g94iU9iMs5Oh+Zp3RJcvYUSD
 y5BIb+IY2ATy20ZkijWmeP8LJz6pja+C9Ne7lKM0jkv7geGeHGAoavz0n3oUq4oz
 IvUNz6hCAP9PcxWc5a9FFqqORLWrRew6GmZmJvIkmC9K+3UQcWhkzO3vLpfl6Q9h
 S728XexkIlhxG9NcER21bFXV2dw3z/X9dm5mQ473TqJm+wQmRuYcPRg053NbqMcx
 juvkweCksx8qlpnjo/1QXQcVwFM8kuR7xAlVo7zdMDOU5F8pdxRnsTl0cUdx5cPv
 DKeMRg8+FYcHmIoe/EodemIh7cAZtEpijZNNAr9cDmAjifeBjWhCb+zri5SIc96x
 0jKVTXyY4jnHXBVoA0FIl1d2t54yVjh3PYiu0MjeLJ9tyB+Px/nOxW8FrdlFnPJ/
 oP5WK13c8h3bMkxUzsvL
 =ZAhA
 -----END PGP SIGNATURE-----

Merge tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull take two of the GPIO updates:
 "Same stuff as last time, now with a fixup patch for the previous
  compile error plus I ran a few extra rounds of compile-testing.

  This is the bulk of GPIO changes for the v3.19 series:

   - A new API that allows setting more than one GPIO at the time.  This
     is implemented for the new descriptor-based API only and makes it
     possible to e.g. toggle a clock and data line at the same time, if
     the hardware can do this with a single register write.  Both
     consumers and drivers need new calls, and the core will fall back
     to driving individual lines where needed.  Implemented for the
     MPC8xxx driver initially

   - Patched the mdio-mux-gpio and the serial mctrl driver that drives
     modems to use the new multiple-setting API to set several signals
     simultaneously

   - Get rid of the global GPIO descriptor array, and instead allocate
     descriptors dynamically for each GPIO on a certain GPIO chip.  This
     moves us closer to getting rid of the limitation of using the
     global, static GPIO numberspace

   - New driver and device tree bindings for 74xx ICs

   - New driver and device tree bindings for the VF610 Vybrid

   - Support the RCAR r8a7793 and r8a7794

   - Guidelines for GPIO device tree bindings trying to get things a bit
     more strict with the advent of combined device properties

   - Suspend/resume support for the MVEBU driver

   - A slew of minor fixes and improvements"

* tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (33 commits)
  gpio: mcp23s08: fix up compilation error
  gpio: pl061: document gpio-ranges property for bindings file
  gpio: pl061: hook request if gpio-ranges avaiable
  gpio: mcp23s08: Add option to configure IRQ output polarity as active high
  gpio: fix deferred probe detection for legacy API
  serial: mctrl_gpio: use gpiod_set_array function
  mdio-mux-gpio: Use GPIO descriptor interface and new gpiod_set_array function
  gpio: remove const modifier from gpiod_get_direction()
  gpio: remove gpio_descs global array
  gpio: mxs: implement get_direction callback
  gpio: em: Use dynamic allocation of GPIOs
  gpio: Check if base is positive before calling gpio_is_valid()
  gpio: mcp23s08: Add simple IRQ support for SPI devices
  gpio: mcp23s08: request a shared interrupt
  gpio: mcp23s08: Do not free unrequested interrupt
  gpio: rcar: Add r8a7793 and r8a7794 support
  gpio-mpc8xxx: add mpc8xxx_gpio_set_multiple function
  gpiolib: allow simultaneous setting of multiple GPIO outputs
  gpio: mvebu: add suspend/resume support
  gpio: gpio-davinci: remove duplicate check on resource
  ..
2014-12-14 14:05:05 -08:00
Maxime Ripard
d5e9fb31ba pinctrl: sunxi: Add A80 pinctrl muxing options
The A80 has a rather usual pin controller, the only thing out of the ordinary
being that it has 5 interrupts banks, and that some pins have several options
for the same functions.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-10-30 15:56:16 +01:00
Maxime Ripard
4f6bd5cfc6 pinctrl: sunxi: Add PN bank base pin
The A80 R-PIO controller has one more bank that what we've seen so far, add the
PN pin bank.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-10-30 15:55:26 +01:00
Alexandre Courbot
e3a2e87893 gpio: rename gpio_lock_as_irq to gpiochip_lock_as_irq
This function actually operates on a gpio_chip, so its prefix should
reflect that fact for consistency with other functions defined in
gpio/driver.h.

Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-10-28 17:30:59 +01:00