Weak header file declarations are error-prone because they make every
definition weak, and the linker chooses one based on link order (see
10629d711e ("PCI: Remove __weak annotation from pcibios_get_phb_of_node
decl")).
That's not a problem for vpe_run() because Kconfig ensures there's never
more than one definition:
- vpe_run() is defined in arch/mips/kernel/vpe-mt.c if
CONFIG_MIPS_VPE_LOADER_MT=y
- vpe_run() is defined in arch/mips/mti-malta/malta-amon.c if
CONFIG_MIPS_CMP=y
- CONFIG_MIPS_VPE_LOADER_MT cannot be set if CONFIG_MIPS_CMP=y
But it's simpler to verify correctness if we remove "weak" from the picture
and test the config symbols directly.
Remove "weak" from the vpe_run() declaration and use #if to test whether a
definition should be present.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-mips@linux-mips.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10684/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
vpe_run() is a weak symbol. If there's no definition of it, its value is
zero.
If vpe_run is zero, return failure early. We're going to fail anyway, so
there's no point in getting a VPE and attempting to load it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-mips@linux-mips.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10683/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Weak header file declarations are error-prone because they make every
definition weak, and the linker chooses one based on link order (see
10629d711e ("PCI: Remove __weak annotation from pcibios_get_phb_of_node
decl")).
platform_maar_init() is defined in:
- arch/mips/mm/init.c (where it is marked "weak")
- arch/mips/mti-malta/malta-memory.c (without annotation)
The "weak" attribute on the platform_maar_init() extern declaration applies
to the platform-specific definition in arch/mips/mti-malta/malta-memory.c,
so both definitions are weak, and which one we get depends on link order.
Remove the "weak" attribute from the declaration. That makes the malta
definition strong, so it will always be preferred if it is present.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: linux-mips@linux-mips.org
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10682/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There's only one implementation of mips_cpc_phys_base(), and it's only used
within the same file, so it doesn't need to be weak, and it doesn't need an
extern declaration.
Remove the extern mips_cpc_phys_base() declaration and make it static.
[ralf@linux-mips.org: Fixed conflict.]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: linux-mips@linux-mips.org
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10681/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The db_assert call checks whether the bus_num pointer is non-NULL, but
does so after said pointer has been dereferenced by the assignment on
the previous line. Thus the check is pointless & likely to have been
optimised out by the compiler anyway. The check_args function is static
& only ever called from the local file with bus_num being a pointer to
an on-stack variable, so the check seems somewhat overzealous anyway.
Simply remove it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10692/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: LKML <linux-kernel@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/10706/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: LKML <linux-kernel@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/10705/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The gpio interrupt handling of octeon contains a homebrewn flow
handler which calls either handle_level_irq or handle_edge_irq
depending on the trigger type. Thats an extra conditional and call in
the interrupt handling path. The proper way to handle different types
and therefor different flows is to update the handler in the
irq_set_type() callback.
Remove the extra indirection and add the handler update to
octeon_irq_ciu_gpio_set_type(). At mapping time it defaults to
handle_level_irq which gets updated if the device tree contains a
different trigger type.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Daney <david.daney@cavium.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: LKML <linux-kernel@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/10704/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The various interrupt flow handlers in ath79 are cascading interrupt
handlers. They all have a disable_irq_nosync()/enable_irq() pair
around the generic_handle_irq() call. The value of this disable/enable
is zero because its a complete noop:
disable_irq_nosync() merily increments the disable count without
actually masking the interrupt. enable_irq() soleley decrements the
disable count without touching the interrupt chip. The interrupt
cannot arrive again because the complete call chain runs with
interrupts disabled.
Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Patchwork: https://patchwork.linux-mips.org/patch/10703/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
bcsr_csc_handler() is a cascading interrupt handler. It has a
disable_irq_nosync()/enable_irq() pair around the generic_handle_irq()
call. The value of this disable/enable is zero because its a complete
noop:
disable_irq_nosync() merily increments the disable count without
actually masking the interrupt. enable_irq() soleley decrements the
disable count without touching the interrupt chip. The interrupt
cannot arrive again because the complete call chain runs with
interrupts disabled.
Remove it.
[ralf@linux-mips.org: Fold in followup fix from Thomas Gleixner.]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Patchwork: https://patchwork.linux-mips.org/patch/10702/
Patchwork: https://patchwork.linux-mips.org/patch/10708/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use irq_set_handler_locked() as it avoids a redundant lookup of the
irq descriptor.
Search and replacement was done with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: LKML <linux-kernel@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/10701/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Hand in irq_data and avoid the redundant lookup of irq_desc.
Originally-from: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10700/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is a preparatory patch for moving irq_data struct members.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: LKML <linux-kernel@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/10699/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Patchwork: https://patchwork.linux-mips.org/patch/10698/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: linux-mips@linux-mips.org
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Patchwork: https://patchwork.linux-mips.org/patch/10697/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: linux-mips@linux-mips.org
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Patchwork: https://patchwork.linux-mips.org/patch/10696/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: linux-mips@linux-mips.org
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Patchwork: https://patchwork.linux-mips.org/patch/10695/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
R6 has dropped the MMUExtDef field from the config4 register and it
now returns 0. However, the return value means nothing in that case
and the only supported configuration for R6 is the VTLB+FTLB
(MMUextDef == 3). As a result, rework the code so that the correct
value is set for R6 cores.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10651/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a default case for the FTLB enable/disable code. This will be used
to detect that something went wrong in the set_ftlb_enable() function
either because that function knows nothing about the running core, or
simply because the core can't turn its FTLB on/off.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10650/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We are so early in the boot process where we really don't want to
stall and wait for CP0 FTLB related changes become visible so just drop
the cp0 hazard barrier.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10649/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CM3 uses a 64-bit counter and compare registers so add support for
them in the GIC counter interrupt.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10648/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Previously, the GIC accessors were only accessing u32 registers but
newer CMs may actually be 64-bit on MIPS64 cores. As a result of which,
extended these accessors to support 64-bit reads and writes.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10709/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The CM cache error reporting code is not Malta specific and as such it
should live in the mips-cm.c file. Moreover, CM2 and CM3 differ in the
way cache errors are being recorded to the registers so extend the
previous code to add support for the CM3 as well.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10646/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The GCR CPC base register is 64-bit on 64-bit processors so use the
appropriate field.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10645/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The CMGCRBase register (CP0, 15, 3) register is 64-bit on MIPS64
so we change its type to unsigned long.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10644/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Previously, the CM accessors were only accessing CM registers as u32
types instead of using the native CM register with. However, newer CMs
may actually be 64-bit on MIPS64 cores. Fortunately, current 64-bit CMs
(CM3) hold all the useful configuration bits in the lower half of the
64-bit registers (at least most of them) so they can still be accessed
using the current 32-bit accessors.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10707/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Allow platforms to perform platform-specific steps before configuring
the L2 cache. This is necessary for platforms with CM3 since the L2
parameters no longer live in the Config2 register.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10642/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Detect the L2 cache configuration from GCR_L2_CONFIG when a CM3 is
present in the system, rather than from Config2 which does not expose
the L2 configuration on I6400.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10641/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Provide accessor functions for the GCR_L2_CONFIG register introduced
with CM3, and define the bits included in the register.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10639/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Provide a function to trivially return the version of the CM present in
the system, or 0 if no CM is present. The mips_cm_revision() will be
used later on to determine the CM register width, so it must not use
the regular CM accessors to read the revision register since that will
lead to build failures due to recursive inlines.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10655/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
R6 does not support the MIPS MT ASE and the CMP/SMP options so
restrict them in order to prevent users from selecting incompatible
SMP configuration for R6 cores. We also disable the CPS/SMP option
because its support hasn't been added to the CPS code yet.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10637/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a case in cpu_probe_mips for the MIPS I6400 processor ID, which sets
the CPU type to the new CPU_I6400.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10636/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a CPU_I6400 case to various switch statements, doing the same thing
as for CPU_P5600.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10635/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the ugly cross tree include now that IRQCHIP_DECLARE moved to
linux/irqchip.h.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10633/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A couple of major (hang and deadlock) fixes with fortunately fairly rare
triggering conditions. The PM oops is only really triggered by people using
enclosure services (rare) and the fnic driver is mostly used in enterprise
environments.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJV2e34AAoJEDeqqVYsXL0MywIH/0ZzZzofgUammzkjalMxoW1b
rojSyB1bpuADc8eXpqsw1x6coNxKK85e9aAmplXqdykgazw44lzkH43Vez7gbwGN
JG5+utu2hQUMJYF9bQ3NLPu5JgxgP0w6aqY1L1ZndKFrRmEnM53UcojNT3M2NIN3
cgA5ICDD0RSQy24KDSZaN+y3SvopEcY5eXUcLfshrwXI3yAIH4G39z8hQHCFGHZB
BkYq9qjI5T4P7PRE5trRYu7B9rO8IJpoYdPnmI3i49jIyJlpFXP3FlLSmL+gCzyO
FBhdln9sCulCWnTirRf7Gsbq6LfXpihtzzgfCtPoxxwI4PRcIBh0jxu3Od8o9NY=
=jY8K
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A couple of major (hang and deadlock) fixes with fortunately fairly
rare triggering conditions. The PM oops is only really triggered by
people using enclosure services (rare) and the fnic driver is mostly
used in enterprise environments"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
SCSI: Fix NULL pointer dereference in runtime PM
fnic: Use the local variable instead of I/O flag to acquire io_req_lock in fnic_queuecommand() to avoid deadloack
Pull MIPS bug fixes from Ralf Baechle:
"Two more fixes for 4.2.
One fixes a build issue with the LLVM assembler - LLVM assembler macro
names are case sensitive, GNU as macro names are insensitive; the
other corrects a license string (GPL v2, not GPLv2) such that the
module loader will recognice the license correctly"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
FIRMWARE: bcm47xx_nvram: Fix module license.
MIPS: Fix LLVM build issue.
Pull 9p regression fix from Al Viro:
"Fix for breakage introduced when switching p9_client_{read,write}() to
struct iov_iter * (went into 4.1)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
9p: ensure err is initialized to 0 in p9_client_read/write
Some use of those functions were providing unitialized values to those
functions. Notably, when reading 0 bytes from an empty file on a 9P
filesystem, the return code of read() was not 0.
Tested with this simple program:
#include <assert.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <unistd.h>
int main(int argc, const char **argv)
{
assert(argc == 2);
char buffer[256];
int fd = open(argv[1], O_RDONLY|O_NOCTTY);
assert(fd >= 0);
assert(read(fd, buffer, 0) == 0);
return 0;
}
Cc: stable@vger.kernel.org # v4.1
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull ARM fixes from Russell King:
"Another couple of small ARM fixes.
A patch from Masahiro Yamada who noticed that "make -jN all zImage"
would end up generating bad images where N > 1, and a patch from
Nicolas to fix the Marvell CPU user access optimisation code when page
faults are disabled"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8418/1: add boot image dependencies to not generate invalid images
ARM: 8414/1: __copy_to_user_memcpy: fix mmap semaphore usage
Pull x86 fixes from Ingo Molnar:
"Various low level fixes: fix more fallout from the FPU rework and the
asm entry code rework, plus an MSI rework fix, and an idle-tracing fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu/math-emu: Fix crash in fork()
x86/fpu/math-emu: Fix math-emu boot crash
x86/idle: Restore trace_cpu_idle to mwait_idle() calls
x86/irq: Build correct vector mapping for multiple MSI interrupts
Revert "sched/x86_64: Don't save flags on context switch"
Pull perf fixes from Ingo Molnar:
"Tooling fixes: a 'perf record' deadlock fix plus debuggability fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf top: Show backtrace when handling a SIGSEGV on --stdio mode
perf tools: Fix buildid processing
perf tools: Make fork event processing more resilient
perf tools: Avoid deadlock when map_groups are broken
Pull irq fixes from Thomas Gleixner:
"A series of small fixlets for a regression visible on OMAP devices
caused by the conversion of the OMAP interrupt chips to hierarchical
interrupt domains. Mostly one liners on the driver side plus a small
helper function in the core to avoid open coded mess in the drivers"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/crossbar: Restore set_wake functionality
irqchip/crossbar: Restore the mask on suspend behaviour
ARM: OMAP: wakeupgen: Restore the irq_set_type() mechanism
irqchip/crossbar: Restore the irq_set_type() mechanism
genirq: Introduce irq_chip_set_type_parent() helper
genirq: Don't return ENOSYS in irq_chip_retrigger_hierarchy
Pull timer fixes from Thomas Gleixner:
"Two minimalistic fixes for 4.2 regressions:
- Eric fixed a thinko in the timer_list base switching code caused by
the overhaul of the timer wheel. It can cause a cpu to see the
wrong base for a timer while we move the timer around.
- Guenter fixed a regression for IMX if booted w/o device tree, where
the timer interrupt is not initialized and therefor the machine
fails to boot"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/imx: Fix boot with non-DT systems
timer: Write timer->flags atomically
During later stages of math-emu bootup the following crash triggers:
math_emulate: 0060:c100d0a8
Kernel panic - not syncing: Math emulation needed in kernel
CPU: 0 PID: 1511 Comm: login Not tainted 4.2.0-rc7+ #1012
[...]
Call Trace:
[<c181d50d>] dump_stack+0x41/0x52
[<c181c918>] panic+0x77/0x189
[<c1003530>] ? math_error+0x140/0x140
[<c164c2d7>] math_emulate+0xba7/0xbd0
[<c100d0a8>] ? fpu__copy+0x138/0x1c0
[<c1109c3c>] ? __alloc_pages_nodemask+0x12c/0x870
[<c136ac20>] ? proc_clear_tty+0x40/0x70
[<c136ac6e>] ? session_clear_tty+0x1e/0x30
[<c1003530>] ? math_error+0x140/0x140
[<c1003575>] do_device_not_available+0x45/0x70
[<c100d0a8>] ? fpu__copy+0x138/0x1c0
[<c18258e6>] error_code+0x5a/0x60
[<c1003530>] ? math_error+0x140/0x140
[<c100d0a8>] ? fpu__copy+0x138/0x1c0
[<c100c205>] arch_dup_task_struct+0x25/0x30
[<c1048cea>] copy_process.part.51+0xea/0x1480
[<c115a8e5>] ? dput+0x175/0x200
[<c136af70>] ? no_tty+0x30/0x30
[<c1157242>] ? do_vfs_ioctl+0x322/0x540
[<c104a21a>] _do_fork+0xca/0x340
[<c1057b06>] ? SyS_rt_sigaction+0x66/0x90
[<c104a557>] SyS_clone+0x27/0x30
[<c1824a80>] sysenter_do_call+0x12/0x12
The reason is the incorrect assumption in fpu_copy(), that FNSAVE
can be executed from math-emu kernels as well.
Don't try to copy the registers, the soft state will be copied
by fork anyway, so the child task inherits the parent task's
soft math state.
With this fix applied math-emu kernels boot up fine on modern
hardware and the 'no387 nofxsr' boot options.
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Bobby Powers <bobbypowers@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On a math-emu bootup the following crash occurs:
Initializing CPU#0
------------[ cut here ]------------
kernel BUG at arch/x86/kernel/traps.c:779!
invalid opcode: 0000 [#1] SMP
[...]
EIP is at do_device_not_available+0xe/0x70
[...]
Call Trace:
[<c18238e6>] error_code+0x5a/0x60
[<c1002bd0>] ? math_error+0x140/0x140
[<c100bbd9>] ? fpu__init_cpu+0x59/0xa0
[<c1012322>] cpu_init+0x202/0x330
[<c104509f>] ? __native_set_fixmap+0x1f/0x30
[<c1b56ab0>] trap_init+0x305/0x346
[<c1b548af>] start_kernel+0x1a5/0x35d
[<c1b542b4>] i386_start_kernel+0x82/0x86
The reason is that in the following commit:
b1276c48e9 ("x86/fpu: Initialize fpregs in fpu__init_cpu_generic()")
I failed to consider math-emu's limitation that it cannot execute the
FNINIT instruction in kernel mode.
The long term fix might be to allow math-emu to execute (certain) kernel
mode FPU instructions, but for now apply the safe (albeit somewhat ugly)
fix: initialize the emulation state explicitly without trapping out to
the FPU emulator.
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While the idea behind get_maintainer seems highly useful it's
unfortunately way to trigger happy to grab people that once had a few
commits to files. For someone like me who does a lot of tree-wide API
work that leads to an incredible amount of Cc spam.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
