This patch removes CONFIG_PMAC_PBOOK (PowerBook support). This is now
split into CONFIG_PMAC_MEDIABAY for the actual hotswap bay that some
powerbooks have, CONFIG_PM for power management related code, and just left
out of any CONFIG_* option for some generally useful stuff that can be used
on non-laptops as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This one-liner fixes a test for interfaces that are already resumed.
It would be nice if this could get into 2.6.12, but it's not critical
since it only affects people doing selective (runtime) suspend/resume.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a build error on pxa25x processes with pxa2xx_udc and
CONFIG_USB_ETH=m
# CONFIG_USB_ETH_RNDIS is not set
The error is because on that CPU there's no status transfer support
except with RNDIS. Workaround, enable the RNDIS support too.
Signed-off-by: Ian Campbell <icampbell@arcom.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
One debug message won't print the right value; OSDL bugid 4545.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch started life as as527, and was rediffed by me.
Since the IDE interface doesn't convey much information about types of
errors, many USB-IDE adapters report all low-level errors with SK = 0x04,
which is supposed to be used only for non-recoverable errors. As a result
the SCSI midlayer doesn't retry the command. But quite often a retry
would succeed, whereas an unnecessary retry doesn't really hurt anything.
This patch uses a recently-implemented flag to tell the SCSI midlayer that
such hardware errors should be retried.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch causes a port reset whenever there's a transport error or abort.
If that fails it reverts back to doing a mass-storage device reset. It
started life as as497 and was rediffed by me.
This makes error recovery a lot quicker and more reliable.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch does two things to help reset recovery. It started life as
as496 and was rediffed by me.
First, the patch checks the result of a CLEAR_HALT request and doesn't reset the
endpoint's data toggle unless the request succeeded.
Second, it reduces the timeout for a device reset from 20 seconds to 5
seconds.
If all goes well, then I've finally figured quilt out and this patch should
apply cleanly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
up(&usblp->sem) was called twice in a row in this code path.
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
> On Sun, Apr 10, 2005 at 07:21:28PM +0600, Viktor A. Danilov wrote:
> >
> > PROBLEM: aiptek input doesn`t register `device` & `driver` section in sysfs (/sys/class/input/event#)
> > REASON: `dev` - field not filled...
> > SOLUTION: in linux/drivers/usb/input/aiptek.c write
> > aiptek->inputdev.dev = &intf->dev;
> > before calling
> > input_register_device(&aiptek->inputdev);
The following (tested) patch fixes the exact same issue with the ATI
Remote input driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added support for Creative WebCam Go Mini.
Camera has STV680 chip and just different Product ID(0x4007) and Vendor ID (0x041e).
Signed-off-by: Kiril Jovchev <jovchev@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initialize status fields in the read and write urbs to prevent a race
condition with open/read/close - open/write/close sequences.
Fixes bug #4432 at bugzilla.kernel.org
Signed-off-by: Adam Oldham <oldhamca@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The itd_patch() function is responsible for allocating entries in the
buffer page pointer list of the iTD. Particularly, a new page pointer
is needed every time when buffer data crosses a page boundary.
However, there is a bug in the allocation logic: the function does not
allocate a new entry when the current transaction is the first
transaction in the iTD (as indicated by first!=0).
The consequence is that, when the data of the first transaction begins
somewhere at the end of a page so that it actually does cross the page
boundary, no new page pointer is allocated. This means that the data
at the end of the first transaction (beyond the page boundary) will be
accessed by the HC using the second page pointer, which is zero.
Furthermore, the first page pointer will be later overwritten by the
page pointers of the other transactions, which will garble it because
the value is or-ed into the iTD field.
All this particular check (for !first) does is cause incorrect
behaviour, so it should be entirely removed (and with it the variable
first that is not used for anything else).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes the way uhci-hcd detects valid ports. The
specification doesn't mention any way to find out how many ports a
controller has, so the driver has to use some heuristics, reading the port
status and control register and deciding whether the value makes sense.
With this patch the driver will recognize a typical failure mode (all bits
set to one) for nonexistent ports and won't assume there are always at
least 2 ports -- such an assumption seems silly if the heuristics have
already shown that the ports don't exist.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drain the rndis response queue on disconnect. This fixes a problem
in which an rndis response left in the queue from a previous session
could cause a subsequent session to fail.
Signed-off-by: Andy Lowe <alowe@mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a compile glitch with CONFIG_USB_ETH_RNDIS disabled, and
replaces some inline #ifdeffery (and other code) with inline functions
which can evaluate to constants.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support to dummy_hcd for suspending and resuming the root
hub and the emulated platform devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the byte-ordering issue for setup packets in the
dummy_hcd driver and cleans up a few things that sparse -Wbitwise
dislikes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
you seem to have applied the original, not the new improved one with
whiter teeth that uses kcalloc instead of kmalloc + memset. Here's a
patch that goes on top of the one you applied.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Work around the gcc-2.95.x macro expansion bug.
Cc: Duncan Sands <baldrick@free.fr>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Zero the entire instance, not just the struct usbatm_data head.
Make sure the just allocated urb is freed if we fail to allocate
a buffer. Based on a patch by Stanislaw W. Gruszka.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reduce the number of "unknown vpi/vci" debug messages to (usually) at most
one per-urb, rather than one per-cell. This is only an issue when (a) many
packets come in but no connection is open; and (b) CONFIG_USB_DEBUG is set.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Doesn't do any firmware loading etc, just transmission and reception.
The user needs to take care of modem initialization, and load the
module with parameters giving the endpoints to use and so forth.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Driver for modems based on the Conexant AccessRunner chipset.
Original patch by Josep Comas, much reworked by Roman Kagan.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Port the speedtch driver to the new usbatm core. The code is much
the same as before, just reorganized, though I threw in some minor
improvements (a new module parameter for choosing the altsetting,
more robust urb failure handling, ...) while I was there.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rework the core usbatm code: minidrivers (i.e. drivers for particular
modems) now register themselves with the usbatm core, supplying methods
for binding/unbinding etc. The design was inspired by usb-serial and
usbnet. At the same time, more common code from the speedtch and
cxacru (patch 3/5) drivers was generalized and moved into the core. The
transmission and reception parts have been unified and simplified. Since
this is a major change and I don't like underscores in file names,
usb_atm.[ch] has been renamed usbatm.[ch].
Many thanks to Roman Kagan, who did a lot of the coding.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various minor EHCI updates
* Dump some more info in the debug dumps, notably the product
description (e.g. chip vendor), BIOS handhake flags, and
debug port status (when it's not managed by the HCD).
* Minor updates to the BIOS handoff code: always flag the HCD
as owned by Linux (in case BIOS doesn't grab it "early"),
and on the buggy-BIOS path always match the "early handoff"
code and forcibly disable SMI IRQs.
* For the disabled 64bit DMA support, there's now a constant
to use for the mask; use it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This has several small updates to the px2xx UDC driver:
* small fixes from Eugeny S. Mints <emints@ru.mvista.com>
- local_irq_save() around potential endpoint disable race
- fix handling of enqueue to OUT endpoints (potential oops)
* add shutdown() method to disable any D+ pullup
* rename methods accessing raw signals, referencing the signals
* describes itself as for "pxa25x", since pxa27x is different
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sparse updates; and the API change for SETUP packets being in USB byteorder.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is mostly "sparse" related updates, one of which was a missing
le32_to_cpu() should have affected big-endian hardware.
Notable is the API change: setup packets are now provided in USB
byte order. This affects only big-endian hardware, and the gadget
drivers have been updated in a separate patch.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This updates most of the gadget framework to expect SETUP packets use
USB byteorder (matching the annotation in <linux/usb_ch9.h> and usage
in the host side stack):
- definition in <linux/usb_gadget.h>
- gadget drivers: Ethernet/RNDIS, serial/ACM, file_storage, gadgetfs.
- dummy_hcd
It also includes some other similar changes as suggested by "sparse",
which was used to detect byteorder bugs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This prevents gadget drivers from being selected when no controller has
been selected, by adding an additional boolean and depending on it.
It's mostly to help "allmodconfig".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the dummy_hcd driver use emulated root-hub interrupts
instead of polling. It's in the spirit of similar changes being made to
the other HCDs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds to the dummy_hcd driver a new routine for keeping track of
all changes in the state of the emulated USB link. The logic is now kept
in one spot instead of spread around, and it's easier to verify and
update the code. The behavior of the port features has been corrected in
a few respects as well (for instance, if the POWER feature is clear then
none of the other features can be set).
Also added is support for the (relatively new) _connect() and
_disconnect() calls of the Gadget API.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the dummy_hcd driver create separate platform devices for
the emulated host controller and emulated device controller. This gives a
more accurate simulation and will permit testing of situations where only
one of the two devices is suspended.
This also changes the name of the host controller platform device to match
the name of the driver. That way the normal platform bus probe mechanism
will handle binding the driver to the device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes some cosmetic changes to dummy_hcd:
Minor alterations of comments and whitespace.
Replace USB_PORT_FEAT_xxx with USB_PORT_STAT_xxx. This is
appropriate as the values are stored in a status variable
and they aren't feature indices. Also it allows the
elimination of a bunch of awkward bit shift operations.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Partial OTG support for dummy_hcd, mostly as a framework for further work.
It emulates the new OTG flags in the host and peripheral frameworks, if
that option is configured. But it's incomplete:
- Resetting the peripheral needs to clear the OTG state bits;
a second enumeration won't work correctly.
- This stops modeling HNP right when roles should switch the first time.
It should probably disconnect, then set the usb_bus.is_b_host and
usb_gadget.is_a_peripheral flags; then it'd enumerate almost normally,
except for the role reversal. Roles could then switch a second time,
back to "normal" (with those flags cleared).
- SRP should be modeled as "resume from port-unpowered", which is
a state that usbcore doesn't yet use.
HNP can be triggered by enabling the OTG whitelist and configuring a
gadget driver that's not in that list; or by configuring Gadget Zero
to identify itself as the HNP test device.
Sent-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
More omap_udc updates:
* OMAP 1710 updates
- new UDC bit for clearing endpoint toggle, affecting CLEAR_HALT
- new OTG bits affecting wakeup
* Fix the bug Vladimir noted, that IN-DMA transfer code path kicks in
for under 1024 bytes (not "up to 1024 bytes")
* Handle transceiver setup more intelligently
- use transceiver whenever one's available; this can be handy
for GPIO based, loopback, or transceiverless configs
- cleanup correctly after the "unrecognized HMC" case
* DMA performance tweaks
- allow burst/pack for memory access
- use 16 bit DMA access most of the time on TIPB
* Add workarounds for some DMA errata (not observed "in the wild"):
- DMA CSAC/CDAC reads returning zero
- RX/TX DMA config registers bit 12 always reads as zero (TI patch)
* More "sparse" warnings removed, notably "changing" the SETUP packet
to return data in USB byteorder (an API change, null effect on OMAP
except for these warnings).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some cleanup for the the Ethernet part of the Ethernet/RNDIS gadget driver:
- Remove remnants of ancient endpoint init logic; this is simpler, clearer
- Save a smidgeon of space in the object file
- Get rid of some #ifdeffery, mostly by using some newish inlines
- Reset more driver state as part of USB reset
- Remove a needless wrapper around an RNDIS call
- Improve and comment the status interrupt handling:
* RNDIS sometimes needs to queue these transfers (rarely in normal
cases, but reproducibly while Windows was deadlocking its USB stack)
* Mark requests as busy/not
- Enable the SET_NETDEV_DEV() call; sysfs seems to behave sanely now
This is a net shrink of source code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some bugfixes and lots of cleanup (net code shrink):
- On reset, force the RNDIS state machine its initial state
- Hook up the RNDIS (outgoing) filters to the CDC mechanism
- Lots of cleanup:
* Eliminate duplicate copy of OID table;
* Unify handlying of the OID "query" response data pointer;
* Reduce code duplication for calculating query response lengths;
* Remove some checks for "can't happen" errors;
* Get rid of debugging #ifdefs by making the debug flag an integer level
Most of the patch, by volume, relates to those query response cleanups.
It incidentally shaves off a few hundred bytes of object code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes the host controller drivers; they no longer need to
register their root hubs because usbcore will take care of it for them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes usbcore automatically allocate and register the root hub
device for a new host controller when the controller is registered. This
way the HCDs don't all have to include the same boilerplate code. As a
pleasant side benefit, the register_root_hub routine can now be made
static and not EXPORTed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes the HCDs that used the old hub_set_power_budget call,
making them use the new hcd->power_budget field instead.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch simplifies the uhci-hcd driver by removing the device pointer
currently stored in the QH and TD structures. Those pointers weren't
being used for anything other than to increment the device's reference
count, which is unnecessary since the device is used only when an URB
completes, and outstanding URBs take their own reference to the device.
As a useful side effect, this change means that uhci-hcd no longer needs
to have the root-hub device available in the start routine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the hub_set_power_budget routine, which was used by a
couple of HCDs to indicate that the root hub was running on battery power.
In its place is a new field added to struct usb_hcd, which HCDs can set
before the root hub is registered. Special-case code in the hub driver
knows to look at this field when configuring a root hub.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
