P1023 external IRQ[4:6, 11] are not pin out, but the interrupts are
utilized by the PCIe controllers. As they are not exposed as pins we
need to set them as active-high (internal to the SoC these interrupts
are pulled down).
IRQs[0:3,7:10] are pulled up on the board so we have them set as
active-low.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (106 commits)
powerpc/p3060qds: Add support for P3060QDS board
powerpc/83xx: Add shutdown request support to MCU handling on MPC8349 MITX
powerpc/85xx: Make kexec to interate over online cpus
powerpc/fsl_booke: Fix comment in head_fsl_booke.S
powerpc/85xx: issue 15 EOI after core reset for FSL CoreNet devices
powerpc/8xxx: Fix interrupt handling in MPC8xxx GPIO driver
powerpc/85xx: Add 'fsl,pq3-gpio' compatiable for GPIO driver
powerpc/86xx: Correct Gianfar support for GE boards
powerpc/cpm: Clear muram before it is in use.
drivers/virt: add ioctl for 32-bit compat on 64-bit to fsl-hv-manager
powerpc/fsl_msi: add support for "msi-address-64" property
powerpc/85xx: Setup secondary cores PIR with hard SMP id
powerpc/fsl-booke: Fix settlbcam for 64-bit
powerpc/85xx: Adding DCSR node to dtsi device trees
powerpc/85xx: clean up FPGA device tree nodes for Freecsale QorIQ boards
powerpc/85xx: fix PHYS_64BIT selection for P1022DS
powerpc/fsl-booke: Fix setup_initial_memory_limit to not blindly map
powerpc: respect mem= setting for early memory limit setup
powerpc: Update corenet64_smp_defconfig
powerpc: Update mpc85xx/corenet 32-bit defconfigs
...
Fix up trivial conflicts in:
- arch/powerpc/configs/40x/hcu4_defconfig
removed stale file, edited elsewhere
- arch/powerpc/include/asm/udbg.h, arch/powerpc/kernel/udbg.c:
added opal and gelic drivers vs added ePAPR driver
- drivers/tty/serial/8250.c
moved UPIO_TSI to powerpc vs removed UPIO_DWAPB support
The P3060QDS is a Freescale reference board that hosts the six-core P3060 SOC.
The P3060 Processor combines six e500mc Power Architecture processor cores with
high-performance datapath acceleration architecture(DPAA), CoreNet fabric
infrastructure, as well as network and peripheral interfaces.
P3060QDS Board Overview:
Memory subsystem:
- 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
- 128M Bytes NOR flash single-chip memory
- 16M Bytes SPI flash
- 8K Bytes AT24C64 I2C EEPROM
Ethernet:
- 4x1G + 4x1G/2.5G Ethernet controllers
- 2xRGMII + 1xMII, three VSC8641 PHYs on board
- Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3
PCIe: Two PCI Express 2.0 controllers/ports
USB: Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board
I2C: Four I2C controllers
UART: Supports up to four UARTs
RapidIO: Supports two serial RapidIO ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The GE DTBs were not updated when the Gianfar driver was converted to an
of_platform_driver in commit b31a1d8b41. Update
the DTBs, adding the required TBI entries.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Adding new device tree binding file for the DCSR node. Modifying device
tree dtsi files to add DCSR node for P2041, P3041, P4080, & P5020.
Signed-off-by: Stephen George <stephen.george@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Standarize and document the FPGA nodes used on Freescale QorIQ reference
boards. There are different kinds of FPGAs used on the boards, but
only two are currently standard: "pixis", "ngpixis", and "qixis". Although
there are minor differences among the boards that have one kind of FPGA, most
of the functionality is the same, so it makes sense to create common
compatibility strings.
We also need to update the P1022DS platform file, because the compatible
string for its PIXIS node has changed. This means that older kernels are
not compatible with newer device trees. This is not a real problem, however,
since that particular function doesn't work anyway. When the DIU is active,
the PIXIS is in "indirect mode", and so cannot be accessed as a memory-mapped
device.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There's only p2041rdb board for official release, but the p2041 silicon
on the board can be converted to p2040 silicon without XAUI and L2 cache
function, then the board becomes p2040rdb board. so we use the file name
p2041_rdb.c to handle P2040RDB board and P2041RDB board which is also
consistent with the board name under U-Boot.
During the rename we make few other minor changes to the device tree:
* Move USB phy setting into p2041si.dtsi as its SoC not board defined
* Convert PCI clock-frequency to decimal to be more readable
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P4080 silicon device tree was using PowerPC,4080 while the other
e500mc based SoCs used PowerPC,e500mc. Use the core name to be
consistent going forward.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
timer0 and timer1 pins are used as simple GPIO on this board.
Add gpio-controller and #gpio-cells properties to timer nodes
so that we can control gpio lines using available MPC52xx
GPT driver.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add new nodes to describe more hardware the board is
equipped with:
- two can nodes for SJA1000 on localbus
- pci node to support Coral-PA graphics controller
- serial node for SC28L92 DUART on localbus
- spi node for MSP430 device
Also correct i2c eeprom node name.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This adds a skeletton for the new Power "Non Virtualized"
platform which will be used by machines supporting running
without an hypervisor, for example in order to run KVM.
These machines will be using a new firmware called OPAL
for which the support will be provided by later patches.
The PowerNV platform is intended to be also usable under
the BML environment used internally for early CPU bringup
which is why the code also supports using RTAS instead of
OPAL in various places.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, the build can (very rarely) fail to build because libfdt.h has
not been created or is in the process of being copied.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In the p1023rds, a physical bus of nor flash is 16 bits width.
The bank-width is width (in bytes) of the bus width. So, the
value of bank-width of nor flash is not one, and it should be
two.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch cleans up the documentation of the device-tree binding for
the Flexcan devices on Freescale's PowerPC and ARM cores. Extra
properties are not used by the driver so we are removing them.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>,
Acked-by: Wolfgang Grandegger <wg@grandegger.com>,
Cc: U Bhaskar-B22300 <B22300@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: socketcan-core@lists.berlios.de,
Cc: netdev@vger.kernel.org,
Cc: PPC list <linuxppc-dev@lists.ozlabs.org>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Taishan (440GX) has the first PHY (EMAC2) mapped at PHY address 1
and the 2nd PHY (EMAC3) at PHY address 3. Use "phy-address" to
correctly describe this instead of "phy-map".
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
For AMP, different kernel instances load into separate memory regions.
Read the start of memory from the device tree and limit the memory to what's
specified in the device tree.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
On P1022DS both ethernet controllers are connected to RGMII PHYs
accessible via MDIO bus. Remove fixed-link property from ethernet
nodes as they only required when fixed link PHYs without MDIO bus
are used.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P2040RDB Specification:
-----------------------
2Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
128 Mbyte NOR flash single-chip memory
256 Kbit M24256 I2C EEPROM
16 Mbyte SPI memory
SD connector to interface with the SD memory card
dTSEC1: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC2: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC3: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC4: connected to the Vitesse RGMII PHY (VSC8641)
dTSEC5: connected to the Vitesse RGMII PHY (VSC8641)
I2C1: Real time clock, Temperature sensor
I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM
SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors
UART: supports two UARTs up to 115200 bps for console
USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces
PCIe:
- Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1
- Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Split out common (non-board specific) parts of the SoC related device
tree into a stub so multiple board dts files can include it and we can
reduce duplication and maintenance effort.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Split out common (non-board specific) parts of the SoC related device
tree into a stub so multiple board dts files can include it and we can
reduce duplication and maintenance effort.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This will allow the new HW RNG driver to bind on these boards
Signed-off-by: Mike Williams <mike@mikebwilliams.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The Sequoia board has a Security function IP block on it that contains a TRNG.
Add the crypto and rng portions of that IP block to the DTS.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
P1010RDB Overview
-----------------
1Gbyte DDR3 (on board DDR)
32Mbyte 16bit NOR flash
32Mbyte SLC NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
I2C Board 128x8 bit memory
SD/MMC connector to interface with the SD memory card
2 SATA interface
1 internal SATA connect to 2.5. 160G SATA2 HDD
1 eSATA connector to rear panel
USB 2.0
x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface.
x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet
eTSEC1: Connected to RGMII PHY VSC8641XKO
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY VSC8221 eCAN
Two DB-9 female connectors for Field bus interface UART
DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Split out common (non-board specific) parts of the SoC related device
tree into a stub so multiple board dts files can include it and we can
reduce duplication and maintenance effort.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
fsl-lbc driver requires an interrupt to bind to localbus device.
Populate 85xx boards' dts trees with lbc interrupt info.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1023 processor is an e500v2 based SoC that utilizes the DPAA
networking architecture. This adds basic board support for non-DPAA
functionality (device tree, board file, etc).
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Added BSD dual-license
* Moved mpic-parent to root so we dont need to duplicate everywhere
* Added next level cache from L2 to CPC
* Moved to 4-cell MPIC interrupt properties
* Added 3 MSI banks
* Added numerous missing nodes: soc-sram-error, guts, pins, clockgen,
rcpm, sfp, serdes, etc.
* Reworked PCIe interrupts to be at virtual bridge level
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add basic device tree for P3041DS board. This device tree excludes
support for DPAA and RapidIO nodes.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add basic device tree for P5020DS board. This device tree excludes
support for DPAA and RapidIO nodes.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On the Freescale P1022DS reference board, the SSI audio controller is
connected in "asynchronous" mode to the codec's clocks, so the device tree
needs an "fsl,ssi-asynchronous" property.
Also remove the clock-frequency property from the wm8776 node, because
the clock is enabled only if U-Boot enables it, and U-Boot will set the
property if the clock is enabled. A future version of the P1022DS audio
driver will configure the clock itself, but for now, the driver should
not be told that the clock is running when it isn't.
Also fix the FIFO depth to 15, instead of 16.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
dtc was moved and .gitignores have been added to the new location. So, we can
delete the old, forgotten ones.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds MSI support for 440SPe, 460Ex, 460Sx and 405Ex.
Signed-off-by: Rupjyoti Sarmah <rsarmah@apm.com>
Signed-off-by: Tirumala R Marri <tmarri@apm.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
