Commit Graph

5 Commits

Author SHA1 Message Date
David Brownell
ab983f2a1b musb: support disconnect after HNP roleswitch
Adjust HNP state machines in MUSB driver so that they handle the
case where the cable is disconnected.  The A-side machine was
very wrong (unrecoverable); the B-Side was much less so.

 - A_PERIPHERAL ... as usual, the non-observability of the ID
   pin through Mentor's registers makes trouble.  We can't go
   directly to A_WAIT_VFALL to end the session and start the
   disconnect processing.  We can however sense link suspending,
   go to A_WAIT_BCON, and from there use OTG timeouts to finally
   trigger that A_WAIT_VFALL transition.  (Hoping that nobody
   reconnects quickly to that port and notices the wrong state.)

 - B_HOST ... actually clear the Host Request (HR) bit as the
   messages say, disconnect the peripheral from the root hub,
   and don't detour through a suspend state.  (In some cases
   this would eventually have cleaned up.)

Also adjust the A_SUSPEND transition to respect the A_AIDL_BDIS
timeout, so if HNP doesn't trigger quickly enough the A_WAIT_VFALL
transition happens as it should.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-15 21:44:41 -07:00
David Brownell
1de00dae80 musb: make initial HNP roleswitch work (v2)
Minor HNP bugfixes, so the initial role switch works:

 - A-Device:
     * disconnect-during-suspend enters A_PERIPHERAL state
     * kill OTG timer after reset as A_PERIPHERAL ...
     * ... and also pass that reset to the gadget
     * once HNP succeeds, clear the "ignore_disconnect" flag
     * from A_PERIPHERAL, disconnect transitions to A_WAIT_BCON

 - B-Device:
     * kill OTG timer on entry to B_HOST state (HNP succeeded)
     * once HNP succeeds, clear "ignore_disconnect" flag
     * kick the root hub only _after_ the state is adjusted

Other state transitions are left alone.  Notably, exit paths from
the "roles have switched" state ... A_PERIPHERAL handling of that
stays seriously broken.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-15 21:44:41 -07:00
David Brownell
84e250ffa7 musb: proper hookup to transceiver drivers
Let the otg_transceiver in MUSB be managed by an external driver;
don't assume it's integrated.  OMAP3 chips need it to be external,
and there may be ways to interact with the transceiver which add
functionality to the system.

Platform init code is responsible for setting up the transeciver,
probably using the NOP transceiver for integrated transceivers.
External ones will use whatever the board init code provided,
such as twl4030 or something more hands-off.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-15 21:44:40 -07:00
Harvey Harrison
551509d267 USB: replace uses of __constant_{endian}
The base versions handle constant folding now.

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-24 16:20:33 -07:00
Felipe Balbi
550a7375fe USB: Add MUSB and TUSB support
This patch adds support for MUSB and TUSB controllers
integrated into omap2430 and davinci. It also adds support
for external tusb6010 controller.

Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-08-13 17:33:00 -07:00