This patch allows the disabling of decompression messages during
x86 bootup.
Signed-off-by: Ben Collins <ben.collins@canonical.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Jeremy Fitzhardinge wrote:
>
> Maybe it really does require the far jump immediately after setting PE
> in cr0...
>
> Hm, I don't remember this paragraph being in vol 3a, section 8.9.1
> before. Is it a recent addition?
>
> Random failures can occur if other instructions exist between steps
> 3 and 4 above. Failures will be readily seen in some situations,
> such as when instructions that reference memory are inserted between
> steps 3 and 4 while in system management mode.
>
I don't remember that, either.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: build failure in maximal configurations
The 32-bit x86 relocatable kernel requires an auxilliary host program
to process the relocations. This program had a hard-coded arbitrary
limit of a 100 ELF sections. Instead of a hard-coded limit, allocate
the structures dynamically.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Apparently, DOS and possibly other legacy operating systems issued a
null command to the keyboard controller after toggling A20,
specifically "pulse output pins" with no output pins specified. This
was presumably done for synchronization reasons. This has made it
into at least the UHCI spec, and it has been found to cause
compatibility problems when "legacy USB" is enabled (which it almost
always is) to not have this byte sent.
It is *NOT* clear if any of these compatibility problems has any
effect on Linux. However, for maximum compatibility, issue this null
command after togging A20 through the KBC.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
... so it could fall back to normal numa and we'd reduce the impact of the
NUMAQ subarch.
NUMAQ depends on GENERICARCH
also decouple genericarch numa from acpi.
also make it fall back to bigsmp if apicid > 8.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch lets the early real mode code look for the 'quiet' option
on the kernel command line and pass a loadflag to the decompressor.
When this flag is set, we suppress the "Decompressing Linux... Parsing
ELF... done." messages.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Replace hardcoded offsets embedded in macros in
arch/x86/boot/compressed with proper structure references.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Trying to boot a 64-bit kernel on a 32bit Pentium 4 gets
you an amusing message along the lines of.
"you need an x86-64, but you only have an i1586"
due to the P4 being family F. Munge it to be 686.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This patch is motivated by a subsequent patch which will allow for more
memory map entries on EFI supported systems than can be passed via the x86
legacy BIOS E820 interface. The legacy interface is limited to E820MAX ==
128 memory entries, and that "E820MAX" manifest constant was used as the
size for several arrays and loops over those arrays.
The primary change in this patch is to change code loop sizes over those
arrays from using the constant E820MAX, to using the ARRAY_SIZE() macro
evaluated for the array being looped. That way, a subsequent patch can
change the size of some of these arrays, without breaking this code.
This patch also adds a parameter to the sanitize_e820_map() routine,
which had an implicit size for the array passed it of E820MAX entries.
This new parameter explicitly passes the size of said array. Once again,
this will allow a subsequent patch to change that array size for some
calls to sanitize_e820_map() without breaking the code.
As part of enhancing the sanitize_e820_map() interface this way, I further
combined the unnecessarily distinct x86_32 and x86_64 declarations for
this routine into a single, commonly used, declaration.
This patch in itself should make no difference to the resulting kernel
binary.
[ mingo@elte.hu: merged to -tip ]
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Just moved an open brace to the previous line.
Signed-off-by: Miklos Vajna <vmiklos@frugalware.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We should better use already defined flags from processor-flags.h instead
of defining own ones
[>>> object code check >>>]
original
md5sum: 129f24be6df396fb7d8bf998c01fc716 arch/x86/boot/compressed/head_64.o
text data bss dec hex filename
705 48 45056 45809 b2f1 arch/x86/boot/compressed/head_64.o
patched
md5sum: 129f24be6df396fb7d8bf998c01fc716 arch/x86/boot/compressed/head_64-new.o
text data bss dec hex filename
705 48 45056 45809 b2f1 arch/x86/boot/compressed/head_64-new.o
[<<< object code check <<<]
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a kernel parameter option to 'edd' to enable/disable BIOS Enhanced Disk
Drive Services. CONFIG_EDD_OFF disables EDD while still compiling EDD into
the kernel. Default behavior can be forced using 'edd=on' or 'edd=off' as
a kernel parameter.
[akpm@linux-foundation.org: fix kernel-parameters.txt]
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds a field of 64-bit physical pointer to NULL terminated
single linked list of struct setup_data to real-mode kernel
header. This is used as a more extensible boot parameters passing
mechanism.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add some autogenerated files to various .gitignore files
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cleanup: change the _end in compressed vmlinux_64.lds.
also change _heap to _ebss that is not needed.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The kernel decompressor wrapper uses memory located beyond the
end of the image. This might lead to hard to debug problems,
but even if it can be proven to be safe, it is at the very
least unclean. I don't see any advantages either, unless you
count it not being zeroed out as an advantage. This patch
moves the boot-heap area to the bss segment.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove old comments that include the old arch/i386 directory.
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move wakeup code to .c, so that video mode setting code can be shared
between boot and wakeup. Remove nasty assembly code in 64-bit case by
re-using trampoline code. Stack setup was fixed to clear high 16bits
of %esp, maybe that fixes some machines.
.c code sharing and morse code was done H. Peter Anvin, Sam Ravnborg
reviewed kbuild related stuff, and it seems okay to him. Rafael did
some cleanups.
[rjw:
* Made the patch stop breaking compilation on x86-32
* Added arch/x86/kernel/acpi/sleep.h
* Got rid of compiler warnings in arch/x86/kernel/acpi/sleep.c
* Fixed 32-bit compilation on x86-64 systems
* Added include/asm-x86/trampoline.h and fixed the non-SMP
compilation on 64-bit x86
* Removed arch/x86/kernel/acpi/sleep_32.c which was not used
* Fixed some breakage caused by the integration of smpboot.c done
under us in the meantime]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In arch/x86/boot/compressed/misc.c, the variable vidmem is
the only variable that ends up in de data segment. It's also
superfluous, because the first thing the code does is:
if (RM_SCREEN_INFO.orig_video_mode == 7) {
vidmem = (char *) 0xb0000;
vidport = 0x3b4;
} else {
vidmem = (char *) 0xb8000;
vidport = 0x3d4;
}
This patch removes the initialisation.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Also update field names to simply payload_{offset,length} so as to not rule
out uncompressed images.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: virtualization@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The new x86 setup code (4fd06960f1) broke booting on an old P3/500MHz
with an onboard Voodoo3 of mine. After debugging it, it turned out
to be caused by the fact that the vesa probing now asks for VBE2 data.
Disassembing the video BIOS shows that it overflows the vesa_general_info
structure when VBE2 data is requested because the source addresses for the
information strings which get strcpy'ed to the buffer lie outside the 32K
BIOS code (and hence contain long sequences of 0xff's).
E.G.:
get_vbe_controller_info:
00002A9C 60 pushaw
00002A9D 1E push ds
00002A9E 0E push cs
00002A9F 1F pop ds
00002AA0 2BC9 sub cx,cx
00002AA2 6626813D56424532 cmp dword [es:di],0x32454256 ; "VBE2"
00002AAA 7501 jnz .1
00002AAC 41 inc cx
.1:
00002AAD 51 push cx
00002AAE B91400 mov cx,0x14
00002AB1 BED47F mov si, controller_header
00002AB4 57 push di
00002AB5 F3A4 rep movsb ; copy vbe1.2 header
00002AB7 B9EC00 mov cx,0xec
00002ABA 2AC0 sub al,al
00002ABC F3AA rep stosb ; zero pad remainder
00002ABE 5F pop di
00002ABF E8EB0D call word get_memory
00002AC2 C1E002 shl ax,0x2
00002AC5 26894512 mov [es:di+0x12],ax ; total memory
00002AC9 26C745040003 mov word [es:di+0x4],0x300 ; VBE version
00002ACF 268C4D08 mov [es:di+0x8],cs
00002AD3 268C4D10 mov [es:di+0x10],cs
00002AD7 59 pop cx
00002AD8 E361 jcxz .done ; VBE2 requested?
00002ADA 8D9D0001 lea bx,[di+0x100]
00002ADE 53 push bx
00002ADF 87DF xchg bx,di ; di now points to 2nd half
00002AE1 26C747140001 mov word [es:bx+0x14],0x100 ; sw rev
00002AE7 26897F06 mov [es:bx+0x6],di ; oem string
00002AEB 268C4708 mov [es:bx+0x8],es
00002AEF BE5280 mov si,0x8052 ; oem string
00002AF2 E87A1B call word strcpy
00002AF5 26897F0E mov [es:bx+0xe],di ; video mode list
00002AF9 268C4710 mov [es:bx+0x10],es
00002AFD B91E00 mov cx,0x1e
00002B00 BEE87F mov si,vidmodes
00002B03 F3A5 rep movsw
00002B05 26897F16 mov [es:bx+0x16],di ; oem vendor
00002B09 268C4718 mov [es:bx+0x18],es
00002B0D BE2480 mov si,0x8024 ; oem vendor
00002B10 E85C1B call word strcpy
00002B13 26897F1A mov [es:bx+0x1a],di ; oem product
00002B17 268C471C mov [es:bx+0x1c],es
00002B1B BE3880 mov si,0x8038 ; oem product
00002B1E E84E1B call word strcpy
00002B21 26897F1E mov [es:bx+0x1e],di ; oem product rev
00002B25 268C4720 mov [es:bx+0x20],es
00002B29 BE4580 mov si,0x8045 ; oem product rev
00002B2C E8401B call word strcpy
00002B2F 58 pop ax
00002B30 B90001 mov cx,0x100
00002B33 2BCF sub cx,di
00002B35 03C8 add cx,ax
00002B37 2AC0 sub al,al
00002B39 F3AA rep stosb ; zero pad
.done:
00002B3B 1F pop ds
00002B3C 61 popaw
00002B3D B84F00 mov ax,0x4f
00002B40 C3 ret
(The full BIOS can be found at http://peter.korsgaard.com/vgabios.bin
if interested).
The old setup code didn't ask for VBE2 info, and the new code doesn't
actually do anything with the extra information, so the fix is to simply
not request it. Other BIOS'es might have the same problem.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The proper way to terminate the e820 chain is with %ebx == 0 on the
last legitimate memory block. However, several BIOSes don't do that
and instead return error (CF = 1) when trying to read off the end of
the list. For this error return, %eax doesn't necessarily return the
SMAP signature -- correctly so, since %ah should contain an error code
in this case.
To deal with some particularly broken BIOSes, we clear the entire e820
chain if the SMAP signature is missing in the middle, indicating a
plain insane e820 implementation. However, we need to make the test
for CF = 1 before the SMAP check.
This fixes at least one HP laptop (nc6400) for which none of the
memory-probing methods (e820, e801, 88) functioned fully according to
spec.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In arch/x86/boot/printf.c gets rid of unused tail of digits: const char
*digits = "0123456789abcdefghijklmnopqrstuvwxyz"; (we are using 0-9a-f
only)
Uses smaller/faster lowercasing (by ORing with 0x20)
if we know that we work on numbers/digits. Makes
strtoul smaller, and also we are getting rid of
static const char small_digits[] = "0123456789abcdefx";
static const char large_digits[] = "0123456789ABCDEFX";
since this works equally well:
static const char digits[16] = "0123456789ABCDEF";
Size savings:
$ size vmlinux.org vmlinux
text data bss dec hex filename
877320 112252 90112 1079684 107984 vmlinux.org
877048 112252 90112 1079412 107874 vmlinux
It may be also a tiny bit faster because code has less
branches now, but I doubt it is measurable.
[ hugh@veritas.com: uppercase pointers fix ]
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Instead of obscure numbers, print the list of missing CPU features in
cleartext. To conserve space, use a host program (mkcpustr.c) to
produce a compact list of mandatory features only.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Do this rather than defining a global version and overriding it in
almost all cases in order to make subsequent patches simpler.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
for bzImage, the vmlinux_64.lds still have s32 bit code, and startup_32
should be 0. fix the comment.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remainder of unification can occur inplace.
size reports no change in arch/x86/boot/compressed/vmlinux.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
size reports no change in arch/x86/boot/compressed/vmlinux.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
size reports no change in arch/x86/boot/compressed/vmlinux.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
size reports no change in arch/x86/boot/compressed/vmlinux.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There seems to be a preference for the 64 bit version so use that on 32 bit and
drop the stray leading "."
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The files are now identical so merge them.
size reports no change in arch/x86/boot/compressed/vmlinux.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
vmlinux_64 and vmlinux_32.scr are now identical
size shows an expected movement from .text to .rodata and 4 extra bytes
of padding.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
size reports no change in arch/x86/boot/compressed/vmlinux.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
size reports no change in arch/x86/boot/compressed/vmlinux.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The GDT_ENTRY() macro in pm.c would incorrectly cut the bottom 8 bits
off the base. We didn't define any bases with the bottom 8 bits
nonzero, so it is a non-manifest bug, but it's still a bug.
Pointed out by John Smith <johnsmith9344@gmail.com>.
Cc: John Smith <johnsmith9344@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If we use the bootloader-provided stack pointer, we might end up in a
situation where the bootloader (incorrectly) pointed the stack in the
middle of our heap. Catch this by simply comparing the computed heap
end value to the stack pointer minus the defined stack size.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Push video mode setup as late as possible; messages issued through the
BIOS interface after video mode setup will either not be seen (for
framebuffer modes) or will screw up the cursor (for text modes.)
In particular, this makes the EDD probing message show up correctly.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tell the user to specify edd=off in the case of EDD probing hangs.
Per LKML discussion.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add prototype for cmdline_find_option_bool() missing from:
x86 setup: early cmdline parser handle boolean options
Also, fix up a minor formatting error in that patch.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Unnecessary capitals are shouting; no need for it here.
Thus, change "OK" to "ok" and add a space.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On early boot, probing the Bios for EDD happens without any message.
Enhanced Disk Drive Services (EDD) is a mechanism to match x86 BIOS device
names (int13 device 80h) to Linux device names (e.g. /dev/sda, /dev/hda)
There are buggy Bios out there having problems with EDD. This can be problems
with the Bios itself or with addon cards, too.
This patch is adds an informational message on early boot.
CONFIG_EDD is not set with defconfig, but with allmodconfig (i.e. CONFIG_EDD=m)
so the EDD probe may be active on early boot on many systems nowadays.
I can tell, that the probe is active on SuSE distro and with that I have seen
more than one system hanging endlessly with those "black screen with a blinking
cursor in the the upper left" on installation, making it difficult for the end-
user to find out, what`s the issue.
For sure I have seen this on FujitsuSiemens PCs with i810 and with i815 chipset.
This one also honours the "quiet" bootparam.
Also see:
http://marc.info/?l=linux-kernel&m=119781937207969&w=2http://marc.info/?l=linux-kernel&m=119783934032326&w=2http://marc.info/?l=linux-kernel&m=119783678529100&w=2
Signed-off-by: Roland Kletzing <devzero@web.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch extends the early commandline parser to support boolean options.
The current version in mainline only supports parsing "option=arg" value pairs.
With this it should be easy making other messages like "Uncompressing kernel"
honour the "quiet" parameter, too.
Signed-off-by: Roland Kletzing <devzero@web.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix the operand constraints for the segment accessor functions,
{rd,wr}{fs,gs}*. In particular, the 8-bit functions used "r"
constraints instead of "q" constraints.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Display VESA graphics modes, with their mode IDs, in the vga=ask
menu. Most VESA mode numbers are platform-dependent, so it helps to
have an easy way to display them.
Based in part on a patch by Petr Vandrovec <petr@vandrovec.name>.
Cc: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To set CR0.PE, use the X86_CR0_PE macro defined in
<asm/processor-flags.h> instead of hardcoding it as a constant (1).
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Intel VT doesn't like to engage when the protected-mode state isn't
fully initialized. Make life easier for it by initializing LDTR (to
null) and TR (to a dummy hunk of low memory which will never actually
be touched.)
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Make the transition to protected mode more paranoid by having
back-to-back near jump (to synchronize the 386/486 prefetch queue) and
far jump (to set up the code segment.)
While we're at it, zero as many registers as practical (for future
expandability of the 32-bit entry interface) and enter 32-bit mode
with a valid stack. Note that the 32-bit code cannot rely on this
stack, or we'll break all other existing users of the 32-bit
entrypoint, but it may make debugging hacks easier to write.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The boot protocol has until now required that the initrd be located in
lowmem, which makes the lowmem/highmem boundary visible to the boot
loader. This was exported to the bootloader via a compile-time
field. Unfortunately, the vmalloc= command-line option breaks this
part of the protocol; instead of adding yet another hack that affects
the bootloader, have the kernel relocate the initrd down below the
lowmem boundary inside the kernel itself.
Note that this does not rely on HIGHMEM being enabled in the kernel.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Previously the complete files were #ifdef'ed, but now handle that in the
Makefile.
May save a minor bit of compilation time.
[ Stephen Rothwell <sfr@canb.auug.org.au>: build dependency fix ]
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
H. Peter Anvin <hpa@zytor.com> wrote:
> It probably should actually HLT, to avoid sucking power, and stressing
> the thermal system. We're dead at this point, and the early 486's
> which had problems with HLT will lock up - we don't care.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Trivial unification of the two Makefiles.
Tested doing a defconfig build for both 32 and 64 bit and
no build changes occured.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There were no reason to mess around with CC, AS and LD.
Fixing this up avoided duplicated option for ld.
A small fixlet were needed in boot/Makefile which assumed
that CC were modified.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We need something here because we can't call in and out instructions
directly. However, we have to be careful, because no indirections are
allowed in misc_64.c , and paravirt_ops is a kind of one. So just
call it directly there
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This updates the exceptions for absolute relocs for the new symbol name
convention used for symbols extracted from the vDSO images.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
x86: provide a DMI based port 0x80 I/O delay override.
Certain (HP) laptops experience trouble from our port 0x80 I/O delay
writes. This patch provides for a DMI based switch to the "alternate
diagnostic port" 0xed (as used by some BIOSes as well) for these.
David P. Reed confirmed that port 0xed works for him and provides a
proper delay. The symptoms of _not_ working are a hanging machine,
with "hwclock" use being a direct trigger.
Earlier versions of this attempted to simply use udelay(2), with the
2 being a value tested to be a nicely conservative upper-bound with
help from many on the linux-kernel mailinglist but that approach has
two problems.
First, pre-loops_per_jiffy calibration (which is post PIT init while
some implementations of the PIT are actually one of the historically
problematic devices that need the delay) udelay() isn't particularly
well-defined. We could initialise loops_per_jiffy conservatively (and
based on CPU family so as to not unduly delay old machines) which
would sort of work, but...
Second, delaying isn't the only effect that a write to port 0x80 has.
It's also a PCI posting barrier which some devices may be explicitly
or implicitly relying on. Alan Cox did a survey and found evidence
that additionally some drivers may be racy on SMP without the bus
locking outb.
Switching to an inb() makes the timing too unpredictable and as such,
this DMI based switch should be the safest approach for now. Any more
invasive changes should get more rigid testing first. It's moreover
only very few machines with the problem and a DMI based hack seems
to fit that situation.
This also introduces a command-line parameter "io_delay" to override
the DMI based choice again:
io_delay=<standard|alternate>
where "standard" means using the standard port 0x80 and "alternate"
port 0xed.
This retains the udelay method as a config (CONFIG_UDELAY_IO_DELAY) and
command-line ("io_delay=udelay") choice for testing purposes as well.
This does not change the io_delay() in the boot code which is using
the same port 0x80 I/O delay but those do not appear to be a problem
as David P. Reed reported the problem was already gone after using the
udelay version. He moreover reported that booting with "acpi=off" also
fixed things and seeing as how ACPI isn't touched until after this DMI
based I/O port switch I believe it's safe to leave the ones in the boot
code be.
The DMI strings from David's HP Pavilion dv9000z are in there already
and we need to get/verify the DMI info from other machines with the
problem, notably the HP Pavilion dv6000z.
This patch is partly based on earlier patches from Pavel Machek and
David P. Reed.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In order to work around old LILO versions providing an invalid ss
register, the current setup code always sets up a new stack,
immediately following .bss and the heap. But this breaks LOADLIN.
This rewrite of the workaround checks for an invalid stack (ss!=ds)
first, and leaves ss:sp alone otherwise (apart from aligning esp).
[hpa note: LOADLIN has a number of arbitrary hard-coded limits that
are being pushed up against. Without some major revision of LOADLIN
itself it will not be sustainable keeping it alive. This gives it
another brief lease on life, however. This patch also helps the
cmdline truncation problem with old versions of SYSLINUX.]
Signed-off-by: Jens Rottmann <JRottmann at LiPPERT-AT. de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
For x86 ARCH may say i386 or x86_64 and soon x86.
Rely on CONFIG_X64_32 to select between 32/64 or just
hardcode the value as appropriate.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Move all CPU definitions to Kconfig.cpu
Always define X86_MINIMUM_CPU_FAMILY and do the
obvious code cleanup in boot/cpucheck.c
Comments from: Adrian Bunk <bunk@kernel.org> incorporated.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@kernel.org>
Cc: Brian Gerst <bgerst@didntduck.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
In accordance with the newly formalized 32-bit boot protocol, set
%ebx == %ebp == %edi == 0 in order to support future extensions to the
protocol.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The kernel only ever supports 1 version of the boot protocol
so there is no need to check the boot protocol revision to
see if a feature is supported.
Both x86 and x86_64 support the same boot protocol so we need
to implement the KEEP_SEGMENTS on x86_64 as well. It isn't
just paravirt bootloaders that could use this functionality.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Andi Kleen <ak@suse.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We use signed values for limit checking since the values can go
negative under certain circumstances. However, sizeof() is unsigned
and forces the comparison to be unsigned, so move the comparison into
the heap_free() macros so we can ensure it is a signed comparison.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Apparently some specific versions of LILO enter the kernel with a
stack pointer that doesn't match the rest of the segments. Make our
best attempt at untangling the resulting mess.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Make <asm/setup.h> usable by the boot code.
Clean up vestiges of the old command-line protocol from setup.h and
head_32.S (it is still supported from the boot loader point of
view, since it is converted to the new command-line protocol by the
boot code.)
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch uses the updated boot protocol to do paravirtualized boot.
If the boot version is >= 2.07, then it will do two things:
1. Check the bootparams loadflags to see if we should reload the
segment registers and clear interrupts. This is appropriate
for normal native boot and some paravirtualized environments, but
inapproprate for others.
2. Check the hardware architecture, and dispatch to the appropriate
kernel entrypoint. If the bootloader doesn't set this, then we
simply do the normal boot sequence.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
x86 uses target specific assignment of EXTRA_AFLAGS,
EXTRA_CFLAGS - this caused troubles with
introducing asflags-y, ccflags-y.
Fixed the target specific assignments in arch/x86/boot/Makefile
and auditted the rest of the kernel for similar usage.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
The variable AFLAGS is a wellknown variable and the usage by
kbuild may result in unexpected behaviour.
On top of that several people over time has asked for a way to
pass in additional flags to gcc.
This patch replace use of AFLAGS with KBUILD_AFLAGS all over
the tree.
Patch was tested on following architectures:
alpha, arm, i386, x86_64, mips, sparc, sparc64, ia64, m68k, s390
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
The variable CFLAGS is a wellknown variable and the usage by
kbuild may result in unexpected behaviour.
On top of that several people over time has asked for a way to
pass in additional flags to gcc.
This patch replace use of CFLAGS with KBUILD_CFLAGS all over the
tree and enabling one to use:
make CFLAGS=...
to specify additional gcc commandline options.
One usecase is when trying to find gcc bugs but other
use cases has been requested too.
Patch was tested on following architectures:
alpha, arm, i386, x86_64, mips, sparc, sparc64, ia64, m68k
Test was simple to do a defconfig build, apply the patch and check
that nothing got rebuild.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
