> Relevant standard (RFC 3493) notes:
>
> The IPV6_UNICAST_HOPS option may be used with getsockopt() to
> determine the hop limit value that the system will use for subsequent
> unicast packets sent via that socket.
>
> I don't reckon -1 could be the hop limit value.
-1 means un-initialized.
> IMHO, the value from
> case 1 (if socket is connected to some destination), otherwise case 2
> (if bound to a scope interface) or ultimately the default hop limit
> ought to be returned instead, as it will be most often correct, while
> the current behavior is always wrong, unless setsockopt() has been used
> first. I don't if some people may think doing a route lookup in
> getsockopt might be overly expensive, but at least the two other cases
> should be ok, particularly the last one.
The following patch seems to work for me, but this code has behaved this
way for a while, so don't know if it will break any existing apps.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a recent patch we introduced invalid return codes which will result in the
opposite of what is intended (i.e. send more packets in face of peculiar
network conditions).
This fixes it by returning ~0 which means not calculated as per
dccp_li_hist_calc_i_mean.
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
If we come to node we'd already marked as seen and it's not a part of path
(i.e. we don't have a loop right there), we already know that it isn't a
part of any loop, so we don't need to revisit it.
That speeds the things up if some chain is refered to from several places
and kills O(exp(table size)) worst-case behaviour (without sleeping,
at that, so if you manage to self-LART that way, you are SOL for a long
time)...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matches and targets verification is duplicated in normal and compat processing
ways. This patch refactors code in order to remove this.
Signed-off-by: Dmitry Mishin <dim@openvz.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
CLUSTERIP, CONNMARK, CONNSECMARK, and connbytes need ip_conntrack or
layer 3 protocol module of nf_conntrack.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
To do that, this makes nf_ct_l3proto_try_module_{get,put} compatible
functions. As a result we can remove '#ifdef' surrounds and direct call of
need_conntrack().
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
NF_NAT depends on NF_CONNTRACK_IPV4, not NF_CONNTRACK.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building with INET=n results in
WARNING: "ip_route_output_key" [net/netfilter/nf_conntrack_h323.ko] undefined!
The entire code in net/netfilter is only used for IPv4/IPv6 currently, so
let it depend on INET.
Noticed by Toralf Förster <toralf.foerster@gmx.de>.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4017/1: [Jornada7xx] - Updating Jornada720.c
[ARM] 3992/1: i.MX/MX1 CPU Frequency scaling support
[ARM] Provide a method to alter the control register
[ARM] 4016/1: prefetch macro is wrong wrt gcc's "delete-null-pointer-checks"
[ARM] Remove empty fixup function
[ARM] 4014/1: include drivers/hid/Kconfig
[ARM] 4013/1: clocksource driver for netx
[ARM] 4012/1: Clocksource for pxa
[ARM] Clean up ioremap code
[ARM] Unuse another Linux PTE bit
[ARM] Clean up KERNEL_RAM_ADDR
[ARM] Add sys_*at syscalls
[ARM] 4004/1: S3C24XX: UDC remove implict addition of VA to regs
[ARM] Formalise the ARMv6 processor name string
[ARM] Handle HWCAP_VFP in VFP support code
[ARM] 4011/1: AT91SAM9260: Fix compilation with NAND driver
[ARM] 4010/1: AT91SAM9260-EK board: Prepare for MACB Ethernet support
Deprecate the old "legacy" PM API, and more importantly default it to "n".
Virtually nothing in-tree uses it any more.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
platform_device_add_data() makes a copy of the data that is given to it,
and thus the parameter can be const. This removes a warning when data
from get_property() on powerpc is handed to platform_device_add_data(),
as get_property() returns a const pointer.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function can be __init
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix file and directory removal in debugfs. Add inotify support for file removal.
The following scenario :
create dir a
create dir a/b
cd a/b (some process goes in cwd a/b)
rmdir a/b
rmdir a
fails due to the fact that "a" appears to be non empty. It is because
the "b" dentry is not deleted from "a" and still in use. The same
problem happens if "b" is a file. d_delete is nice enough to know when
it needs to unhash and free the dentry if nothing else is using it or,
if someone is using it, to remove it from the hash queues and wait for
it to be deleted when it has no users.
The nice side-effect of this fix is that it calls the file removal
notification.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Correct dentry count to handle creation errors.
This patch puts a dput at the file creation instead of the file removal :
lookup_one_len already returns a dentry with reference count of 1. Then,
the dget() in simple_mknod increments it when the dentry is associated
with a file. In a scenario where simple_create or simple_mkdir returns
an error, this would lead to an unwanted increment of the reference
counter, therefore making file removal impossible.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix error handling of file and directory creation in DebugFS.
The error path should release the file system because no _remove will be called
for this erroneous creation.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor coding style fixes along the way : 80 cols and a white space.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Class virtual directory is created as the need arises.
But it is not deleted when the class is unregistered.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Show the initialization state(live, coming, going) of the module:
$ cat /sys/module/usbcore/initstate
live
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* HP Jornada 720 uses epson 1356 chip for graphics. This chip is compatible with s1d13xxxfb driver.
* HP Jornada 720 uses a Microprocessor Control Unit to talk to various
hardware. We add it as a platform device in jornada720_init()
* We provide pm_suspend() to avoid unresolved symbols in apm.o. We are
unable to truly suspend now, hence the stub.
* Speaker/microphone enabling got removed because it will be placed in the alsa driver.
Signed-off-by: Filip Zyzniewski <(address hidden)>
Signed-off-by: Kristoffer Ericson <(address hidden)>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
IA64 is in a tiny minority providing these defines in pci.h.
Almost everyone else has them in scatterlist.h
Signed-off-by: Tony Luck <tony.luck@intel.com>
Support to change MX1 CPU frequency at runtime.
Tested on PiKRON's PiMX1 board and seems to be fully
stable up to 200 MHz end even as low as 8 MHz.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
i.MX needs to tweak the control register to support CPU frequency
scaling. Rather than have folk blindly try and change the control
register by writing to it and then wondering why it doesn't work,
provide a method (which is safe for UP only, and therefore only
available for UP) to achieve this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
optimization
The gcc manual says:
|`-fdelete-null-pointer-checks'
| Use global dataflow analysis to identify and eliminate useless
| checks for null pointers. The compiler assumes that dereferencing
| a null pointer would have halted the program. If a pointer is
| checked after it has already been dereferenced, it cannot be null.
| Enabled at levels `-O2', `-O3', `-Os'.
Now the problem can be seen with this test case:
#include <linux/prefetch.h>
extern void bar(char *x);
void foo(char *x)
{
prefetch(x);
if (x)
bar(x);
}
Because the constraint to the inline asm used in the prefetch() macro is
a memory operand, gcc assumes that the asm code does dereference the
pointer and the delete-null-pointer-checks optimization kicks in.
Inspection of generated assembly for the above example shows that bar()
is indeed called unconditionally without any test on the value of x.
Of course in the prefetch case there is no real dereference and it
cannot be assumed that a null pointer would have been caught at that
point. This causes kernel oopses with constructs like
hlist_for_each_entry() where the list's 'next' content is prefetched
before the pointer is tested against NULL, and only when gcc feels like
applying this optimization which doesn't happen all the time with more
complex code.
It appears that the way to prevent delete-null-pointer-checks
optimization to occur in this case is to make prefetch() into a static
inline function instead of a macro. At least this is what is done on
x86_64 where a similar inline asm memory operand is used (I presume they
would have seen the same problem if it didn't work) and resulting code
for the above example confirms that.
An alternative would consist of replacing the memory operand by a
register operand containing the pointer, and use the addressing mode
explicitly in the asm template. But that would be less optimal than an
offsettable memory reference.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Virtually index, physically tagged cache architectures can get away
without cache flushing when forking. This patch adds a new cache
flushing function flush_cache_dup_mm(struct mm_struct *) which for the
moment I've implemented to do the same thing on all architectures
except on MIPS where it's a no-op.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Provide a custom copy_user_highpage() to deal with aliasing issues on
MIPS. It uses kmap_coherent() to map an user page for kernel with same
color. Rewrite copy_to_user_page() and copy_from_user_page() with the
new interfaces to avoid extra cache flushing.
The main part of this patch was originally written by Ralf Baechle;
Atushi Nemoto did the the debugging.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To allow a more effective copy_user_highpage() on certain architectures,
a vma argument is added to the function and cow_user_page() allowing
the implementation of these functions to check for the VM_EXEC bit.
The main part of this patch was originally written by Ralf Baechle;
Atushi Nemoto did the the debugging.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Problem:
1. There is a process containing two thread (T1 and T2). The
thread T1 calls fork(). Then dup_mmap() function called on T1 context.
static inline int dup_mmap(struct mm_struct *mm, struct mm_struct *oldmm)
...
flush_cache_mm(current->mm);
... /* A */
(write-protect all Copy-On-Write pages)
... /* B */
flush_tlb_mm(current->mm);
...
2. When preemption happens between A and B (or on SMP kernel), the
thread T2 can run and modify data on COW pages without page fault
(modified data will stay in cache).
3. Some time after fork() completed, the thread T2 may cause a page
fault by write-protect on a COW page.
4. Then data of the COW page will be copied to newly allocated
physical page (copy_cow_page()). It reads data via kernel mapping.
The kernel mapping can have different 'color' with user space
mapping of the thread T2 (dcache aliasing). Therefore
copy_cow_page() will copy stale data. Then the modified data in
cache will be lost.
In order to allow architecture code to deal with this problem allow
architecture code to override copy_user_highpage() by defining
__HAVE_ARCH_COPY_USER_HIGHPAGE in <asm/page.h>.
The main part of this patch was originally written by Ralf Baechle;
Atushi Nemoto did the the debugging.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds initial support to 8250-pci for the Korenix Jetcard PCI serial
cards. The JC12xx cards are standard RS232-based serial cards utilising
the Oxford 16C950 device.
The JC14xx are RS422/RS485-based cards, but in order for these to be
supported natively, we will need additional tweaks to the 8250 layers so
we can specify some values for the 950's registers. Hence, these two
entries are commented out.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'for-linus' of git://brick.kernel.dk/data/git/linux-2.6-block:
[PATCH] Fixup cciss error handling
[PATCH] Allow as-iosched to be unloaded
[PATCH 2/2] cciss: remove calls to pci_disable_device
[PATCH 1/2] cciss: map out more memory for config table
[PATCH] Propagate down request sync flag
Resolve trivial whitespace conflict in drivers/block/cciss.c manually.
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon: Add MAINTAINERS entry for new ams driver
hwmon: New AMS hardware monitoring driver
hwmon/w83793: Add documentation and maintainer
hwmon: New Winbond W83793 hardware monitoring driver
hwmon: Update Rudolf Marek's e-mail address
hwmon/f71805f: Fix the device address decoding
hwmon/f71805f: Always create all fan inputs
hwmon/f71805f: Add support for the Fintek F71872F/FG chip
hwmon: New PC87427 hardware monitoring driver
hwmon/it87: Remove the SMBus interface support
hwmon/hdaps: Update the list of supported devices
hwmon/hdaps: Move the DMI detection data to .data
hwmon/pc87360: Autodetect the VRM version
hwmon/f71805f: Document the fan control features
hwmon/f71805f: Add support for "speed mode" fan speed control
hwmon/f71805f: Support DC fan speed control mode
hwmon/f71805f: Let the user adjust the PWM base frequency
hwmon/f71805f: Add manual fan speed control
hwmon/f71805f: Store the fan control registers
Run this:
#!/bin/sh
for f in $(grep -Erl "\([^\)]*\) *k[cmz]alloc" *) ; do
echo "De-casting $f..."
perl -pi -e "s/ ?= ?\([^\)]*\) *(k[cmz]alloc) *\(/ = \1\(/" $f
done
And then go through and reinstate those cases where code is casting pointers
to non-pointers.
And then drop a few hunks which conflicted with outstanding work.
Cc: Russell King <rmk@arm.linux.org.uk>, Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Steven French <sfrench@us.ibm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Modify the sstfb (Voodoo1/2) driver:
- fix a memleak when removing the sstfb module
- fix sstfb to use the fbdev default videomode database
- add module option "mode_option" to set initial screen mode
- add sysfs-interface to turn VGA-passthrough on/off via
/sys/class/graphics/fbX/vgapass
- remove old debug functions from ioctl interface
Signed-off-by: Helge Deller <deller@gmx.de>
Acked-By: James Simmons <jsimmons@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The undocumented register BIOS uses for saving f_CNT seems to only be
mapped to I/O space while all the other HPT3xx regs are dual-mapped. Looks
like another HighPoint's dirty trick. With this patch, the deadly kernel
oops on the cards having the modern HighPoint BIOSes is now at last gone!
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the f_CNT value saved by the HighPoint BIOS if available as reading it
directly would give us a wrong PCI frequency after DPLL has already been
calibrated by BIOS.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
init_chipset_hpt366() modifies some fields of the ide_pci_device_t structure
depending on the chip's revision, so pass it a copy of the structure to avoid
issues when multiple different chips are present.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the broken hotswap code: on HPT37x it caused RESET- to glitch when
tristating the bus (the MISC control 3/6 and soft control 2 need to be written
to in the certain order), and for HPT36x the obsolete HDIO_TRISTATE_HWIF
ioctl() handler was called instead which treated the state argument wrong.
Also, get rid of the soft control reg. 1 wtite to enable IDE interrupt --
this is done in init_hpt37x() already...
Have been tested on HPT370 and 371N.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Save some space on the timing tables by introducing the separate transfer mode
table in which the mode lookup is done to get the index into the timing table
itself. Get rid of the rest of the obsolete/duplicate tables and use one set
of tables for the whole HPT37x chip family like the HighPoint open-source
drivers do. Documnent the different timing register layout for the HPT36x
chip family (this is my guesswork based on the timing values).
Have been tested and works fine on HPT370/302/371N.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix/remove bad/unused timing tables: HPT370/A 66 MHz tables weren't really
needed (the chips are not UltraATA/133 capable and shouldn't support 66 MHz
PCI) and had many modes over- and underclocked, HPT372 33 MHz table was in
fact for 66 MHz and 50 MHz table missed UltraDMA mode 6, HPT374 33 MHz table
was really for 50 MHz... (Actually, HPT370/A 33 MHz tables also have issues.
e.g. HPT370 has PIO modes 0/1 overlocked.)
There's also no need in the separate HPT374 tables because HPT372 timings
should be the same (and those tables has UltraDMA mode 6 which HPT374 supports
depending on HPT374_ALLOW_ATA133_6 #define)...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix serious problems with the HPT372N clock turnaround code:
- the wrong ports were written to when called for the secondary channel;
- it didn't serialize access to the channels;
- turnaround shou;dn't be done on 66 MHz PCI;
- caching the clock mode per-channel caused it to get out of sync with the
actual register value.
Additionally, avoid calibrating PLL twice (for each channel) as the second try
results in a wrong PCI frequency and thus in the wrong timings.
Make the driver deal with HPT302N and HPT371N correctly -- the clocking and
(seemingly) a need for clock tunaround is the same as for HPT372N. HPT371/N
chips have only one, secondary channel, so avoid touching their "pure virtual"
primary channel, and disable it if the BIOS haven't done this already.
Also, while at it, disable UltraATA/133 for HPT372 by default -- 50 MHz DPLL
clock don't allow for this speed anyway. And remove the traces of the former
bad patch that wasn't even applicable to this version of driver.
Has been tested on HPT370/371N, unfortunately I don't have an instant access
to the other chips...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
calc_load() is called by timer interrupt to update avenrun[]. It currently
calls nr_active() at each timer tick (HZ per second), while the update of
avenrun[] is done only once every 5 seconds. (LOAD_FREQ=5 Hz)
nr_active() is quite expensive on SMP machines, since it has to sum up
nr_running and nr_uninterruptible of all online CPUS, bringing foreign
dirty cache lines.
This patch is an optimization of calc_load() so that nr_active() is called
only if we need it.
The use of unlikely() is welcome since the condition is true only once every
5*HZ time.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The nfsservctl system call isn't used but recent nfs-utils releases for
exporting filesystems, and consequently the code that is uses - exp_export -
has suffered some bitrot.
Particular:
- some newly added fields in 'struct svc_export' are being initialised
properly.
- the return value is now always -ENOMEM ...
This patch fixes both these problems.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kill another big "if" clause.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I'm not too fond of these big if conditions. Replace them by checks of a flag
in the operation descriptor. To my eye this makes the code a bit more
self-documenting, and makes the complicated part of the code (proc_compound) a
little more compact.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define an op descriptor struct, use it to simplify nfsd4_proc_compound().
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
