With the removal of the spinlocking around eh calls, we need to add a
little more locking back in, otherwise we do some naked list
manipulation.
Signed-off-by: Dave Boutcher <boutcher@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes the bad assumption of the aacraid driver with use_sg.
I used the 3w-xxxx driver fix as a guide for this.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If your transport class sets the ATTRIBUTE_CONTAINER_NO_CLASSDEVS flag,
then its configure method never gets called. This patch fixes that so
that the configure method is called with a NULL classdev.
Also remove a spurious inverted comma in the transport_class comments.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
remove lots of completely dead code from aiclib, there's not a lot left
and even what's left is rather useless.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
remove ahd_tailq and do sane pci probing. ported over from aic7xxx.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
remove some dead cruft, as done already in aic7xxx
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I recently tried to construct a totally generic transport class and
found there were certain features missing from the current abstract
transport class. Most notable is that you have to hang the data on the
class_device but most of the API is framed in terms of the generic
device, not the class_device.
These changes are two fold
- Provide the class_device to all of the setup and configure APIs
- Provide and extra API to take the device and the attribute class and
return the corresponding class_device
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch is necessary if we begin exposing underlying physical disks
(which can attach to the SPI transport class) of the hardware RAID
cards, since we don't want any SPI parameters binding to the RAID
devices.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Christoph Hellwig <hch@lst.de>
Multi-function cards need to inherit the PCI flags from the master PCI
device.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: "Martin J. Bligh" <mbligh@mbligh.org>
drivers/scsi/aic7xxx/aic7770.c: In function `aic7770_config':
drivers/scsi/aic7xxx/aic7770.c:129: warning: unused variable `l'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Andrew Morton <akpm@osdl.org>
drivers/scsi/scsi.c: In function `scsi_softirq':
drivers/scsi/scsi.c:814: warning: int format, long int arg (arg 4)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Replace use of lpfc_put_lun with midlayer's int_to_scsilun
Remove driver's local definition of lpfc_put_lun (which converts an
int back to a 64-bit LUN) and replace it's use with the recently added
int_to_scsilun function provided by the midlayer.
Note: Embedding midlayer structure in our structure caused
need for more files to include midlayer headers.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix handling of the dev_loss and nodev timeouts.
Symptoms: when remote port disappears for a period of time longer then
either nodev_tmo or dev_loss_tmo, the lpfc driver worker thread will
stall removing that remote port.
Cause: removing remote port involves un-blocking and sync-ing
corresponding block device queue. But corresponding node in the lpfc
driver is still in the NPR(?node port recovery?) state and mid-layer
gets SCSI_MLQUEUE_HOST_BUSY as a return value when it is trying to call
queuecommand() with command for that node (AKA remote port)
Fix: Instead of returning SCSI_MLQUEUE_HOST_BUS from queuecommand() for
nodes in NPR states complete it with retry-able error code DID_BUS_BUSY
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix panic in lpfc_get_stats()
Symptoms: Panic on sysfs stats access
Cause: In lpfc_get_stats() we are writing to memory that we do not
own.
Fix: Fix our stats structure allocation. Embed phba->link_stats in
struct lpfc_hba and stop treating it like rogue structure.
Note: Embedding midlayer/transport structure in our structure caused
need for more files to include midlayer/transport headers.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Clear task management bits when preparing SCSI commands
In lpfc_scsi_prep_cmnd, clear the task management bits (fcpCntl2 member
in the fcp_cmd structure) when preparing regular SCSI commands.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix panic on lip and cable pull
Symptoms: Panic on lip or cable pull
Cause: Use after free of nlp in lpfc_nlp_remove()
Fix: Do not make FC transport calls after a node is removed. Transport
calls are disabled by ignoring the initial delete transition.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
IOCB BDE not getting fully initialized during reuse
Symptoms: Driver gets Status 3 and Reason 0x13 on IOCB completions.
Cause: The IOCB bpl.bdeSize and bdeFlags are not getting initialized on reuse.
Fix: Reinitialize these fields in prep_dma each time an IOCB is used.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Steve Wilcox <spwilcox@att.com>
In order to properly report LUN's > 7, the DEC HSG80 definition in
scsi_devinfo.c needs to include BLIST_REPORTLUN2 rather than
BLIST_SPARSELUN. I've tested this change with several HSG firmware
revisions and with both Emulex and Qlogic HBA's.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's a spurious (and illegal since it's marked __exit) call to
ahc_linux_exit() in ahc_linux_init() which causes a double list
deletion of the transport class; remove it.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When run on a kernel that scans all LUNs, a certain crappy
scsi scanner reports the same LUN over and over..
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=155457
Aparently they were so shamed by this, they chose to remain
anonymous. Though it seems the blacklist code handles
anonymous vendors just fine.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
This patch adds the product ID for the ICP9067MA adapter.
The entries for the ICP9085LI, ICP5085BR, IBM8k & ASR4810SAS were
incorrect and would not initialize the adapters correctly.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There are certain rogue devices (and the aic7xxx driver) that return
BUSY or QUEUE_FULL forever. This code will apply a global timeout (of
the total number of retries times the per command timer) to a given
command. If it is exceeded, the command is completed regardless of its
state.
The patch also removes the unused field in the command: timeout and
timeout_total.
This solves the problem of detecting an endless loop in the mid-layer
because of BUSY/QUEUE_FULL bouncing, but will not recover the device.
In the aic7xxx case, the driver can be recovered by sending a bus reset,
so possibly this should be tied into the error handler?
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I have rediffed the patch against 2.6.13-rc5, done a couple of cosmetic
cleanups, and run some tests. Brian King has acknowledged that it fixes the
problems he has seen. Seems mature enough for inclusion into 2.6.14 (or
later)?
Nate's explanation of the changes:
I've attached patches against 2.6.13rc2. These are basically identical
to my earlier patches, as I found that all issues I'd seen in earlier
kernels still existed in this kernel.
To summarize, the changes are: (more details in my original email)
- add a kref to the scsi_tape structure, and associate reference
counting stuff
- set sr_request->end_io = blk_end_sync_rq so we get notified when an IO
is rejected when the device goes away
- check rq_status when IOs complete, else we don't know that IOs
rejected for a dead device in fact did not complete
- change last_SRpnt so it's set before an async IO is issued (in case
st_sleep_done is bypassed)
- fix a bogus use of last_SRpnt in st_chk_result
Signed-off-by: Nate Dailey <nate.dailey@stratus.com>
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The cmd->timeout field has been obsolete for a while now. While looking
to remove it, I came across this use in the aacraid driver. It looks
like you want to initialise the firmware with the current timeout of the
command (in seconds), so the value I think you should be using is
cmd->timeout_per_command.
Acked by: Mark Haverkamp <markh@osdl.org>
Acked by: Mark Salyzyn <mark_salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
without it you get this failure:
drivers/built-in.o(.text+0xdcccd): In function `ahd_linux_slave_configure':
drivers/scsi/aic7xxx/aic79xx_osm.c:636: undefined reference to `spi_dv_device'
drivers/built-in.o(.text+0xdd7b1): In function `ahd_send_async':
drivers/scsi/aic7xxx/aic79xx_osm.c:1652: undefined reference to `spi_display_xfer_agreement'
drivers/built-in.o(.init.text+0x7b4d): In function `ahd_linux_init':
drivers/scsi/aic7xxx/aic79xx_osm.c:2765: undefined reference to `spi_attach_transport'
drivers/built-in.o(.init.text+0x7c94):drivers/scsi/aic7xxx/aic79xx_osm.c:2774: undefined reference to `spi_release_transport'
drivers/built-in.o(.exit.text+0x72c): In function `ahd_linux_exit':
drivers/scsi/aic7xxx/aic79xx_osm.c:2783: undefined reference to `spi_release_transport'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec:
This patch adds support for the new raw io command. This new command
offers much larger io commands, is more friendly to the internal firmware
structure requiring less translation efforts by the firmware and offers
support for targets greater than 2TB (patch to support >2TB will
be sent in the future).
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec:
If the Adapter is quiet and does not produce an AIF event packets to be
picked up by the management applications for longer than the timeout
interval of two minutes, the cleanup code that deals with aging out
registrants could erroneously drop the registration. The timeout is
there to clean up should the management application die and fail to poll
for updated AIF event packets.
Moving the timer update from the ioctl code that delivers an AIF to the
polling registrant to the bottom of the ioctl means the timeout is reset
with any management application polling activity regardless if an AIF is
delivered or not removing the erroneous timeout cleanups.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec:
This patch removes the duplicate code in the write_callback command
completion handler, and renames read_callback to io_callback. Optimized
the lba calculation into the debug print routine macro to optimize the
i/o code path.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add in pci shutdown method so that the adapter shuts down correctly and
flushes its cache. Shutdown should also disable the adapter's interrupt
when shutdown (in particularly if the driver is rmmod'd) to prevent
spurious hardware activities.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec.
Fixes a bug in check_revision. It should return the driver version not
the firmware version.
Update driver version number.
Update driver version string.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec:
If more than two commands are outstanding to the controller, there is no
need to notify the adapter via a PCI bus transaction of additional
commands added into the queue; it will get to them when it works through
the produce/consumer indexes.
This reduced the PCI traffic in the driver to submit a command to the
queue to near zero allowing a significant number of commands to be
turned around with no need to block for the PCI bridge to flush the
notify request to the adapter.
Interrupt mitigation has always been present in the driver; it was
turned off because of a bug that prevented one from realizing the
usefulness of the feature. This bug is fixed in this patch.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch upports all relevant code fixes and bumps the driver version
to 7.0 to signify starting a new tree.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
this patch is just a cross-port of the fixup for aic7xxx DT settings.
As the same restrictions apply for aic79xx also (DT requires wide
transfers) the dt setting routine should be modified equivalently.
And an invalid period setting will be caught by ahd_find_syncrate()
anyway.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This parameter is important only to people who take the time to tune the
margin control settings, otherwise it's completely irrelevant. However,
just in case anyone should want to do this, it's appropriate to include
the parameter.
I don't do anything with it in DV by design, so the parameter will come
up as off by default, so if anyone actually wants to play with the
margin control settings they'll have to enable it under the
spi_transport class first.
I also updated the transfer settings display to report all of the PPR
settings instead of only DT, IU and QAS
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's a slight problem in the way you've done the transport
parameters; reading from the variables actually produces the current
settings, not the ones you just set (and there's usually a lag because
devices don't renegotiate until the next command goes over the bus). If
you set the bit immediately, you get into the situation where the
transport parameters report something as being set even if the drive
cannot support it.
I patched the driver to do it this way and also corrected a panic in the
proc routines.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch updates various scsi_transport_spi parameters with the actual
parameters used by the driver internally.
Domain Validation for all devices should now work properly.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch updates the aic79xx driver to take advantage of the
scsi_transport_spi infrastructure. Patch is quite a mess as some
procedures have been reshuffled to be closer to the aic7xxx driver.
Rejections fixed and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Jeff Garzik <jgarzik@pobox.com>
This patch removes the busyq in aic79xx and uses the command-queue from
the midlayer instead. Additionally some dead code is removed.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Fixed rejections
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
we have the most recent microcode, make sure to always load it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
