Commit Graph

11 Commits

Author SHA1 Message Date
Martyn Welch
948e78c3fc powerpc/86xx: Renaming following split of GE Fanuc joint venture
This patch renames GE Fanuc boards following the split-up of the GE Fanuc
joint venture. These boards are now made by GE Intelligent platorms.

Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-03-04 10:43:44 -06:00
Martyn Welch
0d81df8701 powerpc/86xx: Enable NVRAM on GE Fanuc's SBC610
This patch enables the NVRAM found on the GE Fanuc SBC610

Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-11-20 16:45:35 -06:00
Kumar Gala
1e76dff22c powerpc/86xx: clean up smp init code
Removed the need for asm/mpc86xx.h as it was only used in mpc86xx_smp.c
and just moved the defines it cared about into there.  Also fixed up
the ioremap to only map the one 4k page we need access to and to iounmap
when we are done.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-05-19 00:50:20 -05:00
Anton Vorontsov
d8bc55fb33 powerpc/86xx: Move gianfar mdio nodes under the ethernet nodes
Currently it doesn't matter where the mdio nodes are placed, but with
power management support (i.e. when sleep = <> properties will take
effect), mdio nodes placement will become important: mdio controller
is a part of the ethernet block, so the mdio nodes should be placed
correctly. Otherwise we may wrongly assume that MDIO controllers are
available during sleep.

Suggested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-03-24 08:35:18 -05:00
Tony Breeds
368a12117d powerpc: Run sbc610 USB fixup code only on the appropriate platform.
commit a969e76a71 (powerpc: Correct USB
support for GE Fanuc SBC610) introduced a fixup for NEC usb controllers.
This fixup should only run on GEF SBC610 boards.

Fixes Fedora bug #486511.
(https://bugzilla.redhat.com/show_bug.cgi?id=486511)

Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-03-04 17:36:52 +11:00
Becky Bruce
f465df81a8 powerpc: Move memory size print into common show_cpuinfo for 32-bit
Most of the platforms were printing the size of the memory
in their show_cpuinfo implementations. This moves that to
the common show_cpuinfo, so that all 32-bit platforms will
now print the size of memory.  I also update the code
to deal with the fact that total_memory is now a phys_addr_t.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2008-10-22 11:00:25 +11:00
Martyn Welch
6675847ea4 powerpc: FPGA support for GE Fanuc SBC610
Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).

This patch adds support for the registers held in the devices main FPGA,
exposing extra information about the revision of the board through cpuinfo.

Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-10-13 11:10:00 -05:00
Martyn Welch
3a47024791 powerpc: GE Fanuc's FPGA based PIC controller on the SBC610
Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC MPC8641D).

A number of MPC8641D based route interrupts for on-board interrupts through
a FPGA based interrupt controller, which is chained with the
MPC8641D's mpic. This patch provides a basic driver to allow basic routing
of interrupts to the mpic.

Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-10-13 11:09:57 -05:00
Martyn Welch
a969e76a71 powerpc: Correct USB support for GE Fanuc SBC610
Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).

Fixup to correctly reconfigure USB, provided by an NEC uPD720101, after
device is reset. This requires a set of chip specific registers in the
devices configuration space to be correctly written, enabling all ports
and switching the device to use an external 48-MHz Oscillator.

Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-09-29 09:25:47 -05:00
Becky Bruce
0161dca52d powerpc: Drop redundant machine type print in show_cpuinfo
For many of the embedded boards, "model" and "Machine" are printing
the same thing; remove the redundant code and allow the generic
show_cpuinfo to print the model information.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-09-29 09:23:06 -05:00
Martyn Welch
54508214cf powerpc: Board support for GE Fanuc SBC610
Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).

This is the basic board support for GE Fanuc's SBC610, a 6U single board
computer, based on Freescale's MPC8641D.

Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-09-16 10:17:14 -05:00