Commit Graph

695 Commits

Author SHA1 Message Date
Alexey Dobriyan
32613090a9 net: constify struct net_protocol
Remove long removed "inet_protocol_base" declaration.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-14 17:03:01 -07:00
Vlad Yasevich
f1751c57f7 sctp: Catch bogus stream sequence numbers
Since our TSN map is capable of holding at most a 4K chunk gap,
there is no way that during this gap, a stream sequence number
(unsigned short) can wrap such that the new number is smaller
then the next expected one.  If such a case is encountered,
this is a protocol violation.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:21:03 -04:00
Wei Yongjun
be2971438d sctp: remove dup code in net/sctp/output.c
Use sctp_packet_reset() instead of dup code.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:21:02 -04:00
Bhaskar Dutta
723884339f sctp: Sysctl configuration for IPv4 Address Scoping
This patch introduces a new sysctl option to make IPv4 Address Scoping
configurable <draft-stewart-tsvwg-sctp-ipv4-00.txt>.

In networking environments where DNAT rules in iptables prerouting
chains convert destination IP's to link-local/private IP addresses,
SCTP connections fail to establish as the INIT chunk is dropped by the
kernel due to address scope match failure.
For example to support overlapping IP addresses (same IP address with
different vlan id) a Layer-5 application listens on link local IP's,
and there is a DNAT rule that maps the destination IP to a link local
IP. Such applications never get the SCTP INIT if the address-scoping
draft is strictly followed.

This sysctl configuration allows SCTP to function in such
unconventional networking environments.

Sysctl options:
0 - Disable IPv4 address scoping draft altogether
1 - Enable IPv4 address scoping (default, current behavior)
2 - Enable address scoping but allow IPv4 private addresses in init/init-ack
3 - Enable address scoping but allow IPv4 link local address in init/init-ack

Signed-off-by: Bhaskar Dutta <bhaskar.dutta@globallogic.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:21:01 -04:00
Vlad Yasevich
8da645e101 sctp: Get rid of an extra routing lookup when adding a transport.
We used to perform 2 routing lookups for a new transport: one
just for path mtu detection, and one to actually route to destination
and path mtu update when sending a packet.  There is no point in doing
both of them, especially since the first one just for path mtu doesn't
take into account source address and sometimes gives the wrong route,
causing path mtu updates anyway.

We now do just the one call to do both route to destination and get
path mtu updates.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:21:01 -04:00
Vlad Yasevich
4007cc88ce sctp: Correctly track if AUTH has been bundled.
We currently track if AUTH has been bundled using the 'auth'
pointer to the chunk.  However, AUTH is disallowed after DATA
is already in the packet, so we need to instead use the
'has_auth' field.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:21:00 -04:00
Wei Yongjun
d521c08f4c sctp: fix to reset packet information after packet transmit
The packet information does not reset after packet transmit, this
may cause some problems such as following DATA chunk be sent without
AUTH chunk, even if the authentication of DATA chunk has been
requested by the peer.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:21:00 -04:00
Vlad Yasevich
31b02e1549 sctp: Failover transmitted list on transport delete
Add-IP feature allows users to delete an active transport.  If that
transport has chunks in flight, those chunks need to be moved to another
transport or association may get into unrecoverable state.

Reported-by: Rafael Laufer <rlaufer@cisco.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:21:00 -04:00
Vlad Yasevich
f68b2e05f3 sctp: Fix SCTP_MAXSEG socket option to comply to spec.
We had a bug that we never stored the user-defined value for
MAXSEG when setting the value on an association.  Thus future
PMTU events ended up re-writing the frag point and increasing
it past user limit.  Additionally, when setting the option on
the socket/endpoint, we effect all current associations, which
is against spec.

Now, we store the user 'maxseg' value along with the computed
'frag_point'.  We inherit 'maxseg' from the socket at association
creation and use it as an upper limit for 'frag_point' when its
set.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:21:00 -04:00
Vlad Yasevich
cb95ea32a4 sctp: Don't do NAGLE delay on large writes that were fragmented small
SCTP will delay the last part of a large write due to NAGLE, if that
part is smaller then MTU.  Since we are doing large writes, we might
as well send the last portion now instead of waiting untill the next
large write happens.  The small portion will be sent as is regardless,
so it's better to not delay it.

This is a result of much discussions with Wei Yongjun <yjwei@cn.fujitsu.com>
and Doug Graham <dgraham@nortel.com>.  Many thanks go out to them.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:59 -04:00
Vlad Yasevich
b29e790728 sctp: Nagle delay should be based on path mtu
The decision to delay due to Nagle should be based on the path mtu
and future packet size.  We currently incorrectly base it on
'frag_point' which is the SCTP DATA segment size, and also we do
not count DATA chunk header overhead in the computation.  This
actuall allows situations where a user can set low 'frag_point',
and then send small messages without delay.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:59 -04:00
Vlad Yasevich
d4d6fb5787 sctp: Try not to change a_rwnd when faking a SACK from SHUTDOWN.
We currently set a_rwnd to 0 when faking a SACK from SHUTDOWN.
This results in an hung association if the remote only uses
SHUTDOWNs (which it's allowed to do) to acknowlege DATA when
closing.  The reason for that is that we simply honor the a_rwnd
from the sack, but since we faked it to be 0, we enter 0-window
probing.  The fix is to use the peers old rwnd and add our flight
size to it.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:59 -04:00
Vlad Yasevich
4d3c46e683 sctp: drop a_rwnd to 0 when receive buffer overflows.
SCTP has a problem that when small chunks are used, it is possible
to exhaust the receiver buffer without fully closing receive window.
This happens due to all overhead that we have account for with small
messages.  To fix this, when receive buffer is exceeded, we'll drop
the window to 0 and save the 'drop' portion.  When application starts
reading data and freeing up recevie buffer space, we'll wait until
we've reached the 'drop' window and then add back this 'drop' one
mtu at a time.  This worked well in testing and under stress produced
rather even recovery.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:59 -04:00
Vlad Yasevich
33ce828131 sctp: Clear fast_recovery on the transport when T3 timer expires.
If T3 timer expires, we are retransmitting data due to timeout any
any fast recovery is null and void.  We can clear the fast recovery
flag.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:58 -04:00
Vlad Yasevich
b9f8478682 sctp: Fix error count increments that were results of HEARTBEATS
SCTP RFC 4960 states that unacknowledged HEARTBEATS count as
errors agains a given transport or endpoint.  As such, we
should increment the error counts for only for unacknowledged
HB, otherwise we detect failure too soon.  This goes for both
the overall error count and the path error count.

Now, there is a difference in how the detection is done
between the two.  The path error detection is done after
the increment, so to detect it properly, we actually need
to exceed the path threshold.  The overall error detection
is done _BEFORE_ the increment.  Thus to detect the failure,
it's enough for the error count to match the threshold.
This is why all the state functions use '>=' to detect failure,
while path detection uses '>'.

Thanks goes to Chunbo Luo <chunbo.luo@windriver.com> who first
proposed patches to fix this issue and made me re-read the spec
and the code to figure out how this cruft really works.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:58 -04:00
Alexey Dobriyan
d71a09ed55 sctp: use proc_create()
create_proc_entry() is deprecated (not formally, though).

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:58 -04:00
Wei Yongjun
dadb50cc1a sctp: fix check the chunk length of received HEARTBEAT-ACK chunk
The receiver of the HEARTBEAT should respond with a HEARTBEAT ACK
that contains the Heartbeat Information field copied from the
received HEARTBEAT chunk. So the received HEARTBEAT-ACK chunk
must have a length of:
  sizeof(sctp_chunkhdr_t) + sizeof(sctp_sender_hb_info_t)

A badly formatted HB-ACK chunk, it is possible that we may access
invalid memory.  We should really make sure that the chunk format
is what we expect, before attempting to touch the data.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:58 -04:00
Wei Yongjun
a2f36eec56 sctp: drop SHUTDOWN chunk if the TSN is less than the CTSN
If Cumulative TSN Ack field of SHUTDOWN chunk is less than the
Cumulative TSN Ack Point then drop the SHUTDOWN chunk.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:57 -04:00
Vlad Yasevich
9c5c62be2f sctp: Send user messages to the lower layer as one
Currenlty, sctp breaks up user messages into fragments and
sends each fragment to the lower layer by itself.  This means
that for each fragment we go all the way down the stack
and back up.  This also discourages bundling of multiple
fragments when they can fit into a sigle packet (ex: due
to user setting a low fragmentation threashold).

We introduce a new command SCTP_CMD_SND_MSG and hand the
whole message down state machine.  The state machine and
the side-effect parser will cork the queue, add all chunks
from the message to the queue, and then un-cork the queue
thus causing the chunks to get transmitted.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:57 -04:00
Vlad Yasevich
5d7ff261ef sctp: Try to encourage SACK bundling with DATA.
If the association has a SACK timer pending and now DATA queued
to be send, we'll try to bundle the SACK with the next application send.
As such, try encourage bundling by accounting for SACK in the size
of the first chunk fragment.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:56 -04:00
Vlad Yasevich
e83963b769 sctp: Generate SACKs when actually sending outbound DATA
We are now trying to bundle SACKs when we have outbound
DATA to send.  However, there are situations where this
outbound DATA will not be sent (due to congestion or 
available window).  In such cases it's ok to wait for the
timer to expire.  This patch refactors the sending code
so that betfore attempting to bundle the SACK we check
to see if the DATA will actually be transmitted.

Based on eirlier works for Doug Graham <dgraham@nortel.com> and
Wei Youngjun <yjwei@cn.fujitsu.com>.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:56 -04:00
Vlad Yasevich
3e62abf92f sctp: Fix data segmentation with small frag_size
Since an application may specify the maximum SCTP fragment size
that all data should be fragmented to, we need to fix how
we do segmentation.   Right now, if a user specifies a small
fragment size, the segment size can go negative in the presence
of AUTH or COOKIE_ECHO bundling.

What we need to do is track the largest possbile DATA chunk that
can fit into the mtu.  Then if the fragment size specified is
bigger then this maximum length, we'll shrink it down.  Otherwise,
we just use the smaller segment size without changing it further.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:56 -04:00
Vlad Yasevich
bec9640bb0 sctp: Disallow new connection on a closing socket
If a socket has a lot of association that are in the process of
of being closed/aborted, it is possible for a remote to establish
new associations during the time period that the old ones are shutting
down.  If this was a result of a close() call, there will be no socket
and will cause a memory leak.  We'll prevent this by setting the
socket state to CLOSING and disallow new associations when in this state.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:56 -04:00
Doug Graham
af87b823ca sctp: Fix piggybacked ACKs
This patch corrects the conditions under which a SACK will be piggybacked
on a DATA packet.  The previous condition was incorrect due to a
misinterpretation of RFC 4960 and/or RFC 2960.  Specifically, the
following paragraph from section 6.2 had not been implemented correctly:

   Before an endpoint transmits a DATA chunk, if any received DATA
   chunks have not been acknowledged (e.g., due to delayed ack), the
   sender should create a SACK and bundle it with the outbound DATA
   chunk, as long as the size of the final SCTP packet does not exceed
   the current MTU.  See Section 6.2.

When about to send a DATA chunk, the code now checks to see if the SACK
timer is running.  If it is, we know we have a SACK to send to the
peer, so we append the SACK (assuming available space in the packet)
and turn off the timer.  For a simple request-response scenario, this
will result in the SACK being bundled with the response, meaning the
the SACK is received quickly by the client, and also meaning that no
separate SACK packet needs to be sent by the server to acknowledge the
request.  Prior to this patch, a separate SACK packet would have been
sent by the server SCTP only after its delayed-ACK timer had expired
(usually 200ms).  This is wasteful of bandwidth, and can also have a
major negative impact on performance due the interaction of delayed ACKs
with the Nagle algorithm.

Signed-off-by: Doug Graham <dgraham@nortel.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:55 -04:00
Vlad Yasevich
40187886bc sctp: release cached route when the transport goes down.
When the sctp transport is marked down, we can release the
cached route and force a new lookup when attempting to use
this transport for anything.  This way, if a better route
or source address is available, we'll try to use it.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:55 -04:00
Wei Yongjun
3cd9749c0b sctp: update the route for non-active transports after addresses are added
Update the route and saddr entries for the non-active transports as some
of the added addresses can be used as better source addresses, or may
be there is a better route.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:55 -04:00
Wei Yongjun
44e65c1ef1 sctp: check the unrecognized ASCONF parameter before access it
This patch fix to check the unrecognized ASCONF parameter before
access it.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:54 -04:00
Wei Yongjun
425e0f6852 sctp: avoid overwrite the return value of sctp_process_asconf_ack()
The return value of sctp_process_asconf_ack() may be
overwritten while process parameters with no error.
This patch fixed the problem.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:54 -04:00
David S. Miller
aa11d958d1 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	arch/microblaze/include/asm/socket.h
2009-08-12 17:44:53 -07:00
Rafael Laufer
418372b0ab sctp: fix missing destroy of percpu counter variable in sctp_proc_exit()
Commit 1748376b66,
	net: Use a percpu_counter for sockets_allocated

added percpu_counter function calls to sctp_proc_init code path, but
forgot to add them to sctp_proc_exit().  This resulted in a following
Ooops when performing this test
	# modprobe sctp
	# rmmod -f sctp
	# modprobe sctp

[  573.862512] BUG: unable to handle kernel paging request at f8214a24
[  573.862518] IP: [<c0308b8f>] __percpu_counter_init+0x3f/0x70
[  573.862530] *pde = 37010067 *pte = 00000000
[  573.862534] Oops: 0002 [#1] SMP
[  573.862537] last sysfs file: /sys/module/libcrc32c/initstate
[  573.862540] Modules linked in: sctp(+) crc32c libcrc32c binfmt_misc bridge
stp bnep lp snd_hda_codec_analog snd_hda_intel snd_hda_codec snd_hwdep
snd_pcm_oss snd_mixer_oss arc4 joydev snd_pcm ecb pcmcia snd_seq_dummy
snd_seq_oss iwlagn iwlcore snd_seq_midi snd_rawmidi snd_seq_midi_event
yenta_socket rsrc_nonstatic thinkpad_acpi snd_seq snd_timer snd_seq_device
mac80211 psmouse sdhci_pci sdhci nvidia(P) ppdev video snd soundcore serio_raw
pcspkr iTCO_wdt iTCO_vendor_support led_class ricoh_mmc pcmcia_core intel_agp
nvram agpgart usbhid parport_pc parport output snd_page_alloc cfg80211 btusb
ohci1394 ieee1394 e1000e [last unloaded: sctp]
[  573.862589]
[  573.862593] Pid: 5373, comm: modprobe Tainted: P  R        (2.6.31-rc3 #6)
7663B15
[  573.862596] EIP: 0060:[<c0308b8f>] EFLAGS: 00010286 CPU: 1
[  573.862599] EIP is at __percpu_counter_init+0x3f/0x70
[  573.862602] EAX: f8214a20 EBX: f80faa14 ECX: c48c0000 EDX: f80faa20
[  573.862604] ESI: f80a7000 EDI: 00000000 EBP: f69d5ef0 ESP: f69d5eec
[  573.862606]  DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[  573.862610] Process modprobe (pid: 5373, ti=f69d4000 task=c2130c70
task.ti=f69d4000)
[  573.862612] Stack:
[  573.862613]  00000000 f69d5f18 f80a70a8 f80fa9fc 00000000 fffffffc f69d5f30
c018e2d4
[  573.862619] <0> 00000000 f80a7000 00000000 f69d5f88 c010112b 00000000
c07029c0 fffffffb
[  573.862626] <0> 00000000 f69d5f38 c018f83f f69d5f54 c0557cad f80fa860
00000001 c07010c0
[  573.862634] Call Trace:
[  573.862644]  [<f80a70a8>] ? sctp_init+0xa8/0x7d4 [sctp]
[  573.862650]  [<c018e2d4>] ? marker_update_probe_range+0x184/0x260
[  573.862659]  [<f80a7000>] ? sctp_init+0x0/0x7d4 [sctp]
[  573.862662]  [<c010112b>] ? do_one_initcall+0x2b/0x160
[  573.862666]  [<c018f83f>] ? tracepoint_module_notify+0x2f/0x40
[  573.862671]  [<c0557cad>] ? notifier_call_chain+0x2d/0x70
[  573.862678]  [<c01588fd>] ? __blocking_notifier_call_chain+0x4d/0x60
[  573.862682]  [<c016b2f1>] ? sys_init_module+0xb1/0x1f0
[  573.862686]  [<c0102ffc>] ? sysenter_do_call+0x12/0x28
[  573.862688] Code: 89 48 08 b8 04 00 00 00 e8 df aa ec ff ba f4 ff ff ff 85
c0 89 43 14 74 31 b8 b0 18 71 c0 e8 19 b9 24 00 a1 c4 18 71 c0 8d 53 0c <89> 50
04 89 43 0c b8 b0 18 71 c0 c7 43 10 c4 18 71 c0 89 15 c4
[  573.862725] EIP: [<c0308b8f>] __percpu_counter_init+0x3f/0x70 SS:ESP
0068:f69d5eec
[  573.862730] CR2: 00000000f8214a24
[  573.862734] ---[ end trace 39c4e0b55e7cf54d ]---

Signed-off-by: Rafael Laufer <rlaufer@cisco.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-09 21:45:43 -07:00
Jan Engelhardt
36cbd3dcc1 net: mark read-only arrays as const
String literals are constant, and usually, we can also tag the array
of pointers const too, moving it to the .rodata section.

Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-05 10:42:58 -07:00
Wei Yongjun
1bc4ee4088 sctp: fix warning at inet_sock_destruct() while release sctp socket
Commit 'net: Move rx skb_orphan call to where needed' broken sctp protocol
with warning at inet_sock_destruct(). Actually, sctp can do this right with
sctp_sock_rfree_frag() and sctp_skb_set_owner_r_frag() pair.

    sctp_sock_rfree_frag(skb);
    sctp_skb_set_owner_r_frag(skb, newsk);

This patch not revert the commit d55d87fdff,
instead remove the sctp_sock_rfree_frag() function.

------------[ cut here ]------------
WARNING: at net/ipv4/af_inet.c:151 inet_sock_destruct+0xe0/0x142()
Modules linked in: sctp ipv6 dm_mirror dm_region_hash dm_log dm_multipath
scsi_mod ext3 jbd uhci_hcd ohci_hcd ehci_hcd [last unloaded: scsi_wait_scan]
Pid: 1808, comm: sctp_test Not tainted 2.6.31-rc2 #40
Call Trace:
 [<c042dd06>] warn_slowpath_common+0x6a/0x81
 [<c064a39a>] ? inet_sock_destruct+0xe0/0x142
 [<c042dd2f>] warn_slowpath_null+0x12/0x15
 [<c064a39a>] inet_sock_destruct+0xe0/0x142
 [<c05fde44>] __sk_free+0x19/0xcc
 [<c05fdf50>] sk_free+0x18/0x1a
 [<ca0d14ad>] sctp_close+0x192/0x1a1 [sctp]
 [<c0649f7f>] inet_release+0x47/0x4d
 [<c05fba4d>] sock_release+0x19/0x5e
 [<c05fbab3>] sock_close+0x21/0x25
 [<c049c31b>] __fput+0xde/0x189
 [<c049c3de>] fput+0x18/0x1a
 [<c049988f>] filp_close+0x56/0x60
 [<c042f422>] put_files_struct+0x5d/0xa1
 [<c042f49f>] exit_files+0x39/0x3d
 [<c043086a>] do_exit+0x1a5/0x5dd
 [<c04a86c2>] ? d_kill+0x35/0x3b
 [<c0438fa4>] ? dequeue_signal+0xa6/0x115
 [<c0430d05>] do_group_exit+0x63/0x8a
 [<c0439504>] get_signal_to_deliver+0x2e1/0x2f9
 [<c0401d9e>] do_notify_resume+0x7c/0x6b5
 [<c043f601>] ? autoremove_wake_function+0x0/0x34
 [<c04a864e>] ? __d_free+0x3d/0x40
 [<c04a867b>] ? d_free+0x2a/0x3c
 [<c049ba7e>] ? vfs_write+0x103/0x117
 [<c05fc8fa>] ? sys_socketcall+0x178/0x182
 [<c0402a56>] work_notifysig+0x13/0x19
---[ end trace 9db92c463e789fba ]---

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-06 12:47:08 -07:00
Wei Yongjun
ff0ac74afb sctp: xmit sctp packet always return no route error
Commit 'net: skb->dst accessors'(adf30907d6)
broken the sctp protocol stack, the sctp packet can never be sent out after
Eric Dumazet's patch, which have typo in the sctp code.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Vlad Yasevich <vladisalv.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-29 19:41:53 -07:00
Brian Haley
d5fdd6babc ipv6: Use correct data types for ICMPv6 type and code
Change all the code that deals directly with ICMPv6 type and code
values to use u8 instead of a signed int as that's the actual data
type.

Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-23 04:31:07 -07:00
Eric Dumazet
31e6d363ab net: correct off-by-one write allocations reports
commit 2b85a34e91
(net: No more expensive sock_hold()/sock_put() on each tx)
changed initial sk_wmem_alloc value.

We need to take into account this offset when reporting
sk_wmem_alloc to user, in PROC_FS files or various
ioctls (SIOCOUTQ/TIOCOUTQ)

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-18 00:29:12 -07:00
Jesper Dangaard Brouer
eaa184a1a1 sctp: protocol.c call rcu_barrier() on unload.
On module unload call rcu_barrier(), this is needed as synchronize_rcu()
is not strong enough.  The kmem_cache_destroy() does invoke
synchronize_rcu() but it does not provide same protection.

Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-10 01:11:25 -07:00
David S. Miller
1b003be39e sctp: Use frag list abstraction interfaces.
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-09 00:24:07 -07:00
Vlad Yasevich
c6ba68a266 sctp: support non-blocking version of the new sctp_connectx() API
Prior implementation of the new sctp_connectx() call that returns
an association ID did not work correctly on non-blocking socket.
This is because we could not return both a EINPROGRESS error and
an association id.  This is a new implementation that supports this.

Originally from Ivan Skytte Jørgensen <isj-sctp@i1.dk

Signed-off-by: Ivan Skytte Jørgensen <isj-sctp@i1.dk
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-06-03 09:14:47 -04:00
Wei Yongjun
9919b455fc sctp: fix to choose alternate destination when retransmit ASCONF chunk
RFC 5061 Section 5.1 ASCONF Chunk Procedures said:

B4)  Re-transmit the ASCONF Chunk last sent and if possible choose an
     alternate destination address (please refer to [RFC4960],
     Section 6.4.1).  An endpoint MUST NOT add new parameters to this
     chunk; it MUST be the same (including its Sequence Number) as
     the last ASCONF sent.  An endpoint MAY, however, bundle an
     additional ASCONF with new ASCONF parameters with the next
     Sequence Number.  For details, see Section 5.5.

This patch fix to choose an alternate destination address when
re-transmit the ASCONF chunk, with some dup codes cleanup.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-06-03 09:14:46 -04:00
Jean-Mickael Guerin
d48e074dfd sctp: fix sack_timeout sysctl min and max types
sctp_sack_timeout is defined as int, but the sysctl's maxsize is set
to sizeof(long) and the min/max are defined as long.

Signed-off-by: jean-mickael.guerin@6wind.com
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-06-03 09:14:46 -04:00
Wei Yongjun
10a43cea7d sctp: fix panic when T4-rto timer expire on removed transport
If T4-rto timer is expired on a removed transport, kernel panic
will occur when we do failure management on that transport.
You can reproduce this use the following sequence:

Endpoint A                           Endpoint B
(ESTABLISHED)                        (ESTABLISHED)

            <-----------------      ASCONF
                                    (SRC=X)
ASCONF        ----------------->
(Delete IP Address = X)
            <-----------------      ASCONF-ACK
                                    (Success Indication)
            <-----------------      ASCONF
                                    (T4-rto timer expire)

This patch fixed the problem.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-06-03 09:14:46 -04:00
Wei Yongjun
6345b19985 sctp: fix panic when T2-shutdown timer expire on removed transport
If T2-shutdown timer is expired on a removed transport, kernel
panic will occur when we do failure management on that transport.
You can reproduce this use the following sequence:

  Endpoint A                           Endpoint B
  (ESTABLISHED)                        (ESTABLISHED)

                <-----------------      SHUTDOWN
                                        (SRC=X)
  ASCONF        ----------------->
  (Delete IP Address = X)
                <-----------------      ASCONF-ACK
                                        (Success Indication)
                <-----------------      SHUTDOWN
                                        (T2-shutdown timer expire)
This patch fixed the problem.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-06-03 09:14:46 -04:00
Wei Yongjun
a2c395846c sctp: fix to only enable IPv6 address support on PF_INET6 socket
If socket is create by PF_INET type, it can not used IPv6 address
to send/recv DATA. So only enable IPv6 address support on PF_INET6
socket.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-06-03 09:14:46 -04:00
Wei Yongjun
4553e88d87 sctp: fix a typo in net/sctp/sm_statetable.c
Just fix a typo in net/sctp/sm_statetable.c.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-06-03 09:14:45 -04:00
Wei Yongjun
945e5abcee sctp: fix the error code when ASCONF is received with invalid address
Use Unresolvable Address error cause instead of Invalid Mandatory
Parameter error cause when process ASCONF chunk with invalid address
since address parameters are not mandatory in the ASCONF chunk.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-06-03 09:14:45 -04:00
Wei Yongjun
a987f762ca sctp: fix report unrecognized parameter in ACSONF-ACK
RFC5061 Section 5.2.  Upon Reception of an ASCONF Chunk

V2)  In processing the chunk, the receiver should build a
     response message with the appropriate error TLVs, as
     specified in the Parameter type bits, for any ASCONF
     Parameter it does not understand.  To indicate an
     unrecognized parameter, Cause Type 8 should be used as
     defined in the ERROR in Section 3.3.10.8, [RFC4960].  The
     endpoint may also use the response to carry rejections for
     other reasons, such as resource shortages, etc., using the
     Error Cause TLV and an appropriate error condition.

So we should indicate an unrecognized parameter with error
SCTP_ERROR_UNKNOWN_PARAM in ACSONF-ACK chunk, not
SCTP_ERROR_INV_PARAM.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-06-03 09:14:45 -04:00
Eric Dumazet
adf30907d6 net: skb->dst accessors
Define three accessors to get/set dst attached to a skb

struct dst_entry *skb_dst(const struct sk_buff *skb)

void skb_dst_set(struct sk_buff *skb, struct dst_entry *dst)

void skb_dst_drop(struct sk_buff *skb)
This one should replace occurrences of :
dst_release(skb->dst)
skb->dst = NULL;

Delete skb->dst field

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-03 02:51:04 -07:00
Eric Dumazet
511c3f92ad net: skb->rtable accessor
Define skb_rtable(const struct sk_buff *skb) accessor to get rtable from skb

Delete skb->rtable field

Setting rtable is not allowed, just set dst instead as rtable is an alias.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-03 02:51:02 -07:00
Jesse Brandeburg
8dc92f7e2e sctp: add feature bit for SCTP offload in hardware
this is the sctp code to enable hardware crc32c offload for
adapters that support it.

Originally by: Vlad Yasevich <vladislav.yasevich@hp.com>

modified by Jesse Brandeburg <jesse.brandeburg@intel.com>

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-28 01:53:14 -07:00
Alexey Dobriyan
99b7623380 proc 2/2: remove struct proc_dir_entry::owner
Setting ->owner as done currently (pde->owner = THIS_MODULE) is racy
as correctly noted at bug #12454. Someone can lookup entry with NULL
->owner, thus not pinning enything, and release it later resulting
in module refcount underflow.

We can keep ->owner and supply it at registration time like ->proc_fops
and ->data.

But this leaves ->owner as easy-manipulative field (just one C assignment)
and somebody will forget to unpin previous/pin current module when
switching ->owner. ->proc_fops is declared as "const" which should give
some thoughts.

->read_proc/->write_proc were just fixed to not require ->owner for
protection.

rmmod'ed directories will be empty and return "." and ".." -- no harm.
And directories with tricky enough readdir and lookup shouldn't be modular.
We definitely don't want such modular code.

Removing ->owner will also make PDE smaller.

So, let's nuke it.

Kudos to Jeff Layton for reminding about this, let's say, oversight.

http://bugzilla.kernel.org/show_bug.cgi?id=12454

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
2009-03-31 01:14:44 +04:00
Vlad Yasevich
8d2f9e8116 sctp: Clean up TEST_FRAME hacks.
Remove 2 TEST_FRAME hacks that are no longer needed.  These allowed
sctp regression tests to compile before, but are no longer needed.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 13:41:09 -07:00
David S. Miller
2b1c4354de Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/virtio_net.c
2009-03-20 02:27:41 -07:00
Al Viro
cb0dc77de0 net: fix sctp breakage
broken by commit 5e739d1752aca4e8f3e794d431503bfca3162df4; AFAICS should
be -stable fodder as well...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Aced-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18 19:12:42 -07:00
malc
6fc791ee63 sctp: add Adaptation Layer Indication parameter only when it's set
RFC5061 states:

        Each adaptation layer that is defined that wishes
        to use this parameter MUST specify an adaptation code point in an
        appropriate RFC defining its use and meaning.

If the user has not set one - assume they don't want to sent the param
with a zero Adaptation Code Point.

Rationale - Currently the IANA defines zero as reserved - and
1 as the only valid value - so we consider zero to be unset - to save
adding a boolean to the socket structure.

Including this parameter unconditionally causes endpoints that do not
understand it to report errors unnecessarily.

Signed-off-by: Malcolm Lashley <mlashley@gmail.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-13 11:37:58 -07:00
Wei Yongjun
76595024ff sctp: fix to send FORWARD-TSN chunk only if peer has such capable
RFC3758 Section 3.3.1.  Sending Forward-TSN-Supported param in INIT

   Note that if the endpoint chooses NOT to include the parameter, then
   at no time during the life of the association can it send or process
   a FORWARD TSN.

If peer does not support PR-SCTP capable, don't send FORWARD-TSN chunk
to peer.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-13 11:37:58 -07:00
Wei Yongjun
5ffad5aceb sctp: fix to indicate ASCONF support in INIT-ACK only if peer has such capable
This patch fix to indicate ASCONF support in INIT-ACK only if peer has
such capable.

This patch also fix to calc the chunk size if peer has no FWD-TSN
capable.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-13 11:37:56 -07:00
Vlad Yasevich
5e8f3f703a sctp: simplify sctp listening code
sctp_inet_listen() call is split between UDP and TCP style.  Looking
at the code, the two functions are almost the same and can be
merged into a single helper.  This also fixes a bug that was
fixed in the UDP function, but missed in the TCP function.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-13 11:37:56 -07:00
David S. Miller
508827ff0a Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/tokenring/tmspci.c
	drivers/net/ucc_geth_mii.c
2009-03-05 02:06:47 -08:00
Brian Haley
fb13d9f9e4 SCTP: change sctp_ctl_sock_init() to try IPv4 if IPv6 fails
Change sctp_ctl_sock_init() to try IPv4 if IPv6 socket registration
fails.  Required if the IPv6 module is loaded with "disable=1", else
SCTP will fail to load.

Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-04 03:20:26 -08:00
Vlad Yasevich
7e99013a50 sctp: Fix broken RTO-doubling for data retransmits
Commit faee47cdbf
(sctp: Fix the RTO-doubling on idle-link heartbeats)
broke the RTO doubling for data retransmits.  If the
heartbeat was sent before the data T3-rtx time, the
the RTO will not double upon the T3-rtx expiration.
Distingish between the operations by passing an argument
to the function.

Additionally, Wei Youngjun pointed out that our treatment
of requested HEARTBEATS and timer HEARTBEATS is the same
wrt resetting congestion window.  That needs to be separated,
since user requested HEARTBEATS should not treat the link
as idle.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02 22:49:18 -08:00
Wei Yongjun
f61f6f82c9 sctp: use time_before or time_after for comparing jiffies
The functions time_before or time_after are more robust
for comparing jiffies against other values.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02 22:49:18 -08:00
Wei Yongjun
c6db93a58f sctp: fix the length check in sctp_getsockopt_maxburst()
The code in sctp_getsockopt_maxburst() doesn't allow len to be larger
then struct sctp_assoc_value, which is a common case where app writers
just pass down the sizeof(buf) or something similar.

This patch fix the problem.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02 22:49:17 -08:00
Wei Yongjun
d212318c9d sctp: remove dup code in net/sctp/socket.c
Remove dup check of "if (optlen < sizeof(int))".

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02 22:49:16 -08:00
Wei Yongjun
906f8257ee sctp: Add some missing types for debug message
This patch add the type name "AUTH" and primitive type name
"PRIMITIVE_ASCONF" for debug message.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02 22:49:16 -08:00
Wei Yongjun
3df2678737 sctp: fix kernel panic with ERROR chunk containing too many error causes
If ERROR chunk is received with too many error causes in ESTABLISHED
state, the kernel get panic.

This is because sctp limit the max length of cmds to 14, but while
ERROR chunk is received, one error cause will add around 2 cmds by
sctp_add_cmd_sf(). So many error causes will fill the limit of cmds
and panic.

This patch fixed the problem.

This bug can be test by SCTP Conformance Test Suite
<http://networktest.sourceforge.net/>.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02 22:27:39 -08:00
Vlad Yasevich
d1dd524785 sctp: fix crash during module unload
An extra list_del() during the module load failure and unload
resulted in a crash with a list corruption.  Now sctp can
be unloaded again.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02 22:27:38 -08:00
Vlad Yasevich
914e1c8b69 sctp: Inherit all socket options from parent correctly.
During peeloff/accept() sctp needs to save the parent socket state
into the new socket so that any options set on the parent are
inherited by the child socket.  This was found when the
parent/listener socket issues SO_BINDTODEVICE, but the
data was misrouted after a route cache flush.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-16 00:03:11 -08:00
Vlad Yasevich
faee47cdbf sctp: Fix the RTO-doubling on idle-link heartbeats
SCTP incorrectly doubles rto ever time a Hearbeat chunk
is generated.   However RFC 4960 states:

   On an idle destination address that is allowed to heartbeat, it is
   recommended that a HEARTBEAT chunk is sent once per RTO of that
   destination address plus the protocol parameter 'HB.interval', with
   jittering of +/- 50% of the RTO value, and exponential backoff of the
   RTO if the previous HEARTBEAT is unanswered.

Essentially, of if the heartbean is unacknowledged, do we double the RTO.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-16 00:03:10 -08:00
Vlad Yasevich
4458f04c02 sctp: Clean up sctp checksumming code
The sctp crc32c checksum is always generated in little endian.
So, we clean up the code to treat it as little endian and remove
all the __force casts.

Suggested by Herbert Xu.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-16 00:03:10 -08:00
Lucas Nussbaum
06e868066e sctp: Allow to disable SCTP checksums via module parameter
This is a new version of my patch, now using a module parameter instead
of a sysctl, so that the option is harder to find. Please note that,
once the module is loaded, it is still possible to change the value of
the parameter in /sys/module/sctp/parameters/, which is useful if you
want to do performance comparisons without rebooting.

Computation of SCTP checksums significantly affects the performance of
SCTP. For example, using two dual-Opteron 246 connected using a Gbe
network, it was not possible to achieve more than ~730 Mbps, compared to
941 Mbps after disabling SCTP checksums.
Unfortunately, SCTP checksum offloading in NICs is not commonly
available (yet).

By default, checksums are still enabled, of course.

Signed-off-by: Lucas Nussbaum <lucas.nussbaum@ens-lyon.fr>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-16 00:03:09 -08:00
Harvey Harrison
09640e6365 net: replace uses of __constant_{endian}
Base versions handle constant folding now.

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-01 00:45:17 -08:00
David S. Miller
3eacdf58c2 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 2009-01-26 17:43:16 -08:00
Vlad Yasevich
ae53b5bd77 sctp: Fix another socket race during accept/peeloff
There is a race between sctp_rcv() and sctp_accept() where we
have moved the association from the listening socket to the
accepted socket, but sctp_rcv() processing cached the old
socket and continues to use it.

The easy solution is to check for the socket mismatch once we've
grabed the socket lock.  If we hit a mis-match, that means
that were are currently holding the lock on the listening socket,
but the association is refrencing a newly accepted socket.  We need
to drop the lock on the old socket and grab the lock on the new one.

A more proper solution might be to create accepted sockets when
the new association is established, similar to TCP.  That would
eliminate the race for 1-to-1 style sockets, but it would still
existing for 1-to-many sockets where a user wished to peeloff an
association.  For now, we'll live with this easy solution as
it addresses the problem.

Reported-by: Michal Hocko <mhocko@suse.cz>
Reported-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-22 14:53:23 -08:00
Vlad Yasevich
759af00ebe sctp: Properly timestamp outgoing data chunks for rtx purposes
Recent changes to the retransmit code exposed a long standing
bug where it was possible for a chunk to be time stamped
after the retransmit timer was reset.  This caused a rare
situation where the retrnamist timer has expired, but
nothing was marked for retrnasmission because all of
timesamps on data were less then 1 rto ago.  As result,
the timer was never restarted since nothing was retransmitted,
and this resulted in a hung association that did couldn't
complete the data transfer.  The solution is to timestamp
the chunk when it's added to the packet for transmission
purposes.  After the packet is trsnmitted the rtx timer
is restarted.  This guarantees that when the timer expires,
there will be data to retransmit.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-22 14:53:01 -08:00
Vlad Yasevich
6574df9a89 sctp: Correctly start rtx timer on new packet transmissions.
Commit 62aeaff5cc
(sctp: Start T3-RTX timer when fast retransmitting lowest TSN)
introduced a regression where it was possible to forcibly
restart the sctp retransmit timer at the transmission of any
new chunk.  This resulted in much longer timeout times and
sometimes hung sctp connections.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-22 14:52:43 -08:00
Joe Perches
4fe1d58bf5 sctp/ipv6.c: use ipv6_addr_copy
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-22 13:49:44 -08:00
Coly Li
73ac36ea14 fix similar typos to successfull
When I review ocfs2 code, find there are 2 typos to "successfull".  After
doing grep "successfull " in kernel tree, 22 typos found totally -- great
minds always think alike :)

This patch fixes all the similar typos. Thanks for Randy's ack and comments.

Signed-off-by: Coly Li <coyli@suse.de>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-08 08:31:15 -08:00
Frederik Schwarzer
025dfdafe7 trivial: fix then -> than typos in comments and documentation
- (better, more, bigger ...) then -> (...) than

Signed-off-by: Frederik Schwarzer <schwarzerf@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-01-06 11:28:06 +01:00
Wei Yongjun
8510b937ae sctp: Add validity check for SCTP_PARTIAL_DELIVERY_POINT socket option
The latest ietf socket extensions API draft said:

  8.1.21.  Set or Get the SCTP Partial Delivery Point

    Note also that the call will fail if the user attempts to set
    this value larger than the socket receive buffer size.

This patch add this validity check for SCTP_PARTIAL_DELIVERY_POINT
socket option.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-25 16:59:03 -08:00
Wei Yongjun
9fcb95a105 sctp: Avoid memory overflow while FWD-TSN chunk is received with bad stream ID
If FWD-TSN chunk is received with bad stream ID, the sctp will not do the
validity check, this may cause memory overflow when overwrite the TSN of
the stream ID.

The FORWARD-TSN chunk is like this:

FORWARD-TSN chunk
  Type                       = 192
  Flags                      = 0
  Length                     = 172
  NewTSN                     = 99
  Stream                     = 10000
  StreamSequence             = 0xFFFF

This patch fix this problem by discard the chunk if stream ID is not
less than MIS.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-25 16:58:11 -08:00
Wei Yongjun
aea3c5c05d sctp: Implement socket option SCTP_GET_ASSOC_NUMBER
Implement socket option SCTP_GET_ASSOC_NUMBER of the latest ietf socket
extensions API draft.

  8.2.5.  Get the Current Number of Associations (SCTP_GET_ASSOC_NUMBER)

   This option gets the current number of associations that are attached
   to a one-to-many style socket.  The option value is an uint32_t.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-25 16:57:24 -08:00
Wei Yongjun
ea686a2653 sctp: Fix a typo in socket.c
Just fix a typo in socket.c.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-25 16:56:45 -08:00
Wei Yongjun
e89c209581 sctp: Bring SCTP_MAXSEG socket option into ietf API extension compliance
Brings maxseg socket option set/get into line with the latest ietf socket
extensions API draft, while maintaining backwards compatibility.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-25 16:54:58 -08:00
Randy Dunlap
157653ce79 sctp: fix missing label when PROC_FS=n
Fix missing label when CONFIG_PROC_FS=n:

net/sctp/protocol.c: In function 'sctp_proc_init':
net/sctp/protocol.c:106: error: label 'out_nomem' used but not defined
make[3]: *** [net/sctp/protocol.o] Error 1

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-27 15:30:53 -08:00
Eric Dumazet
1748376b66 net: Use a percpu_counter for sockets_allocated
Instead of using one atomic_t per protocol, use a percpu_counter
for "sockets_allocated", to reduce cache line contention on
heavy duty network servers. 

Note : We revert commit (248969ae31
net: af_unix can make unix_nr_socks visbile in /proc),
since it is not anymore used after sock_prot_inuse_add() addition

Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-25 21:16:35 -08:00
Eric Dumazet
5bc0b3bfa7 net: Make sure BHs are disabled in sock_prot_inuse_add()
prot->destroy is not called with BH disabled. So we must add
explicit BH disable around call to sock_prot_inuse_add()
in sctp_destroy_sock()

Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-25 13:53:27 -08:00
David S. Miller
6f756a8c36 net: Make sure BHs are disabled in sock_prot_inuse_add()
The rule of calling sock_prot_inuse_add() is that BHs must
be disabled.  Some new calls were added where this was not
true and this tiggers warnings as reported by Ilpo.

Fix this by adding explicit BH disabling around those call sites.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-23 17:34:03 -08:00
Eric Dumazet
9a57f7fabd net: sctp should update its inuse counter
This patch is a preparation to namespace conversion of /proc/net/protocols

In order to have relevant information for SCTP protocols, we should use
sock_prot_inuse_add() to update a (percpu and pernamespace) counter of
inuse sockets.

Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-17 02:41:00 -08:00
Alexey Dobriyan
6d9f239a1e net: '&' redux
I want to compile out proc_* and sysctl_* handlers totally and
stub them to NULL depending on config options, however usage of &
will prevent this, since taking adress of NULL pointer will break
compilation.

So, drop & in front of every ->proc_handler and every ->strategy
handler, it was never needed in fact.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-03 18:21:05 -08:00
Harvey Harrison
21454aaad3 net: replace NIPQUAD() in net/*/
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u
can be replaced with %pI4

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-31 00:54:56 -07:00
Harvey Harrison
5b095d9892 net: replace %p6 with %pI6
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-29 12:52:50 -07:00
Harvey Harrison
fdb46ee752 net, misc: replace uses of NIP6_FMT with %p6
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-28 23:02:32 -07:00
Wei Yongjun
2e3f92dad6 sctp: Fix to handle SHUTDOWN in SHUTDOWN_RECEIVED state
Once an endpoint has reached the SHUTDOWN-RECEIVED state,
it MUST NOT send a SHUTDOWN in response to a ULP request.
The Cumulative TSN Ack of the received SHUTDOWN chunk
MUST be processed.

This patch fix to process Cumulative TSN Ack of the received
SHUTDOWN chunk in SHUTDOWN_RECEIVED state.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-23 01:01:18 -07:00
Wei Yongjun
cf896d514a sctp: Fix to handle SHUTDOWN in SHUTDOWN-PENDING state
If SHUTDOWN is received in SHUTDOWN-PENDING state, enpoint should enter
the SHUTDOWN-RECEIVED state and check the Cumulative TSN Ack field of
the SHUTDOWN chunk (RFC 4960 Section 9.2). If the SHUTDOWN chunk can
acknowledge all of the send DATA chunks, SHUTDOWN-ACK should be sent.

But now endpoint just silently discarded the SHUTDOWN chunk.

SHUTDOWN received in SHUTDOWN-PENDING state can happend when the last
SACK is lost by network, or the SHUTDOWN chunk can acknowledge all of
the received DATA chunks. The packet sequence(SACK lost) is like this:

Endpoint A                       Endpoint B       ULP
(ESTABLISHED)                    (ESTABLISHED)

               <-----------      DATA
                                             <--- shutdown
                                 Enter SHUTDOWN-PENDING state
  SACK         ----lost---->

  SHUTDOWN(*1) ------------>

               <-----------      SHUTDOWN-ACK

 (*1) silently discarded now.

This patch fix to handle SHUTDOWN in SHUTDOWN-PENDING state as the same
as ESTABLISHED state.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-23 01:00:49 -07:00
Wei Yongjun
df10eec476 sctp: Add check for the TSN field of the SHUTDOWN chunk
If SHUTDOWN chunk is received Cumulative TSN Ack beyond the max tsn currently
send, SHUTDOWN chunk be accepted and the association will be broken. New data
is send, but after received SACK it will be drop because TSN in SACK is less
than the Cumulative TSN, data will be retrans again and again even if correct
SACK is received.

The packet sequence is like this:

Endpoint A                       Endpoint B       ULP
(ESTABLISHED)                    (ESTABLISHED)

               <-----------      DATA (TSN=x-1)

               <-----------      DATA (TSN=x)

  SHUTDOWN     ----------->      (Now Cumulative TSN=x+1000)
  (TSN=x+1000)
               <-----------      DATA (TSN=x+1)

  SACK         ----------->      drop the SACK
  (TSN=x+1)
               <-----------      DATA (TSN=x+1)(retrans)

This patch fix this problem by terminating the association and respond to
the sender with an ABORT.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-23 01:00:21 -07:00
Wei Yongjun
91bd6b1e03 sctp: Drop ICMP packet too big message with MTU larger than current PMTU
If ICMP packet too big message is received with MTU larger than current
PMTU, SCTP will still accept this ICMP message and sync the PMTU of assoc
with the wrong MTU.

Endpoing A                 Endpoint B
(ESTABLISHED)              (ESTABLISHED)
ICMP         --------->
(packet too big, MTU too larger)
                           sync PMTU

This patch fixed the problem by drop that ICMP message.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-23 00:59:52 -07:00
Vlad Yasevich
a1080a8b0b sctp: update SNMP statiscts when T5 timer expired.
The T5 timer is the timer for the over-all shutdown procedure.  If
this timer expires, then shutdown procedure has not completed and we
ABORT the association.  We should update SCTP_MIB_ABORTED and
SCTP_MIB_CURRESTAB  when aborting.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-09 14:33:26 -07:00
Vlad Yasevich
56eb82bb8d sctp: Fix SNMP number of SCTP_MIB_ABORTED during violation handling.
If ABORT chunks require authentication and a protocol violation
is triggered, we do not tear down the association.  Subsequently,
we should not increment SCTP_MIB_ABORTED.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-09 14:33:01 -07:00
Wei Yongjun
3d5a019d57 sctp: Fix the SNMP number of SCTP_MIB_CURRESTAB
RFC3873 defined SCTP_MIB_CURRESTAB:
  sctpCurrEstab OBJECT-TYPE
    SYNTAX         Gauge32
    MAX-ACCESS     read-only
    STATUS         current
    DESCRIPTION
         "The number of associations for which the current state is
         either ESTABLISHED, SHUTDOWN-RECEIVED or SHUTDOWN-PENDING."
    REFERENCE
         "Section 4 in RFC2960 covers the SCTP   Association state
         diagram."

If the T4 RTO timer expires many times(timeout), the association will enter
CLOSED state, so we should dec the number of SCTP_MIB_CURRESTAB, not inc the
number of SCTP_MIB_CURRESTAB.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-09 14:32:24 -07:00
Vlad Yasevich
02015180e2 sctp: shrink sctp_tsnmap some more by removing gabs array
The gabs array in the sctp_tsnmap structure is only used
in one place, sctp_make_sack().  As such, carrying the
array around in the sctp_tsnmap and thus directly in
the sctp_association is rather pointless since most
of the time it's just taking up space.  Now, let
sctp_make_sack create and populate it and then throw
it away when it's done.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08 14:19:01 -07:00
Vlad Yasevich
8e1ee18c33 sctp: Rework the tsn map to use generic bitmap.
The tsn map currently use is 4K large and is stuck inside
the sctp_association structure making memory references REALLY
expensive.  What we really need is at most 4K worth of bits
so the biggest map we would have is 512 bytes.   Also, the
map is only really usefull when we have gaps to store and
report.  As such, starting with minimal map of say 32 TSNs (bits)
should be enough for normal low-loss operations.  We can grow
the map by some multiple of 32 along with some extra room any
time we receive the TSN which would put us outside of the map
boundry.  As we close gaps, we can shift the map to rebase
it on the latest TSN we've seen.  This saves 4088 bytes per
association just in the map alone along savings from the now
unnecessary structure members.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08 14:18:39 -07:00
Denis V. Lunev
e41b5368e0 ipv6: added net argument to ICMP6_INC_STATS_BH
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08 11:14:13 -07:00
Vlad Yasevich
e69c4e0f12 sctp: correctly save sctp_adaptation from parameter.
The INIT perameter carries the adapatation value in network-byte
order.  We need to store it in host byte order as expected
by data types and the user API.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2008-10-01 11:34:16 -04:00
Vlad Yasevich
96cd0d3d71 sctp: enable cookie-echo retransmission transport switch
This patch enables cookie-echo retransmission transport switch
feature. If COOKIE-ECHO retransmission happens, it will be sent
to the address other than the one last sent to.

Signed-off-by: Gui Jianfeng <guijianfeng@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2008-10-01 11:34:16 -04:00
Wei Yongjun
8190f89dfd sctp: Fix the SNMP counter of SCTP_MIB_OUTOFBLUES
RFC3873 defined SCTP_MIB_OUTOFBLUES:

 sctpOutOfBlues OBJECT-TYPE
   SYNTAX         Counter32
   MAX-ACCESS     read-only
   STATUS         current
   DESCRIPTION
        "The number of out of the blue packets received by the host.
        An out of the blue packet is an SCTP packet correctly formed,
        including the proper checksum, but for which the receiver was
        unable to identify an appropriate association."
   REFERENCE
        "Section 8.4 in RFC2960 deals with the Out-Of-The-Blue
         (OOTB) packet definition and procedures."

But OOTB packet INIT, INIT-ACK and SHUTDOWN-ACK(COOKIE-WAIT or
COOKIE-ECHOED state) are not counted by SCTP_MIB_OUTOFBLUES.

Case 1(INIT):

Endpoint A               Endpoint B
(CLOSED)                 (CLOSED)

 INIT     ---------->
          <----------    ABORT

Case 2(INIT-ACK):

Endpoint A               Endpoint B
(CLOSED)                 (CLOSED)

 INIT-ACK  ---------->
           <----------   ABORT

Case 3(SHUTDOWN-ACK):

Endpoint A               Endpoint B
(CLOSED)                 (CLOSED)

          <----------    INIT
 SHUTDOWN-ACK  ---------->
           <----------   SHUTDOWN-COMPLETE

Case 4(SHUTDOWN-ACK):

Endpoint A               Endpoint B
(CLOSED)                 (COOKIE-ECHOED)

 SHUTDOWN-ACK  ---------->
           <----------   SHUTDOWN-COMPLETE

This patch fixed the problem.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2008-10-01 11:34:16 -04:00
Wei Yongjun
536428a9b9 sctp: Fix to start T5-shutdown-guard timer while enter SHUTDOWN-SENT state
RFC 4960: Section 9.2
The sender of the SHUTDOWN MAY also start an overall guard timer
'T5-shutdown-guard' to bound the overall time for the shutdown
sequence.  At the expiration of this timer, the sender SHOULD abort
the association by sending an ABORT chunk.  If the 'T5-shutdown-
guard' timer is used, it SHOULD be set to the recommended value of 5
times 'RTO.Max'.

The timer 'T5-shutdown-guard' is used to counter the overall time
for shutdown sequence, and it's start by the sender of the SHUTDOWN.
So timer 'T5-shutdown-guard' should be start when we send the first
SHUTDOWN chunk and enter the SHUTDOWN-SENT state, not start when we
receipt of the SHUTDOWN primitive and enter SHUTDOWN-PENDING state.

If 'T5-shutdown-guard' timer is start at SHUTDOWN-PENDING state, the
association may be ABORT while data is still transmitting.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2008-10-01 11:34:16 -04:00
Vlad Yasevich
52cae8f06b sctp: try harder to figure out address family when checking wildcards
sctp_is_any() function that is used to check for wildcard addresses
only looks at the address itself to determine the address family.
This function is used in the API to check the address passed in from
the user.  If the user simply zerroes out the sockaddr_storage and
pass that in, we'll end up failing.  So, let's try harder to determine
the address family by also checking the socket if it's possible.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2008-10-01 11:33:06 -04:00
Neil Horman
c226ef9b83 sctp: reduce memory footprint of sctp_chunk structure
sctp_chunks should be put on a diet.  This is some of the low hanging
fruit that we can strip out.  Changes all the __s8/__u8 flags to
bitfields.  Saves 12 bytes per chunk.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2008-10-01 11:33:06 -04:00
Vlad Yasevich
845b8eda4d sctp: Retransmit list is ineligable for missing indications
Chunks placed on the retransmit list are marked as inelegible
for fast retrasnmission.   Since missing indications determine
when fast reransmission is done, there is not point in calling
sctp_mark_missing() on the retransmit list since those chunks
will not be marked.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2008-10-01 11:33:06 -04:00
Vlad Yasevich
ab5216a5bd sctp: Optimize SFR-CACC transport list walking during SACK processing
There is a possibility of walking the transport list twice during
SACK processing when doing SFR-CACC algorithm.  We can restructure
the code to only do this once.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2008-10-01 11:33:06 -04:00
Vlad Yasevich
2cd9b822bf sctp: Only mark chunks as missing when there are gaps
Frist small step in optimizing SACK processing.   Do not call
sctp_mark_missing() when there are no gaps reported and thus
not missing chunks.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2008-10-01 11:33:06 -04:00
David S. Miller
b262e60309 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:

	drivers/net/wireless/ath9k/core.c
	drivers/net/wireless/ath9k/main.c
	net/core/dev.c
2008-10-01 06:12:56 -07:00
Wei Yongjun
ba0166708e sctp: Fix kernel panic while process protocol violation parameter
Since call to function sctp_sf_abort_violation() need paramter 'arg' with
'struct sctp_chunk' type, it will read the chunk type and chunk length from
the chunk_hdr member of chunk. But call to sctp_sf_violation_paramlen()
always with 'struct sctp_paramhdr' type's parameter, it will be passed to
sctp_sf_abort_violation(). This may cause kernel panic.

   sctp_sf_violation_paramlen()
     |-- sctp_sf_abort_violation()
        |-- sctp_make_abort_violation()

This patch fixed this problem. This patch also fix two place which called
sctp_sf_violation_paramlen() with wrong paramter type.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-09-30 05:32:24 -07:00
David S. Miller
43f59c8939 net: Remove __skb_insert() calls outside of skbuff internals.
This minor cleanup simplifies later changes which will convert
struct sk_buff and friends over to using struct list_head.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-09-21 21:28:51 -07:00
Vlad Yasevich
add52379dd sctp: Fix oops when INIT-ACK indicates that peer doesn't support AUTH
If INIT-ACK is received with SupportedExtensions parameter which
indicates that the peer does not support AUTH, the packet will be
silently ignore, and sctp_process_init() do cleanup all of the
transports in the association.
When T1-Init timer is expires, OOPS happen while we try to choose
a different init transport.

The solution is to only clean up the non-active transports, i.e
the ones that the peer added.  However, that introduces a problem
with sctp_connectx(), because we don't mark the proper state for
the transports provided by the user.  So, we'll simply mark
user-provided transports as ACTIVE.  That will allow INIT
retransmissions to work properly in the sctp_connectx() context
and prevent the crash.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-09-18 16:28:27 -07:00
Vlad Yasevich
0ef46e285c sctp: do not enable peer features if we can't do them.
Do not enable peer features like addip and auth, if they
are administratively disabled localy.  If the peer resports
that he supports something that we don't, neither end can
use it so enabling it is pointless.  This solves a problem
when talking to a peer that has auth and addip enabled while
we do not.  Found by Andrei Pelinescu-Onciul <andrei@iptel.org>.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-09-18 16:27:38 -07:00
Vlad Yasevich
a3028b8ed1 sctp: set the skb->ip_summed correctly when sending over loopback.
Loopback used to clobber the ip_summed filed which sctp then used
to figure out if it needed to do checksumming or not.  Now that
loopback doesn't do that any more, sctp needs to set the ip_summed
field correctly.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-09-18 02:48:25 -07:00
Vlad Yasevich
d97240552c sctp: fix random memory dereference with SCTP_HMAC_IDENT option.
The number of identifiers needs to be checked against the option
length.  Also, the identifier index provided needs to be verified
to make sure that it doesn't exceed the bounds of the array.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-08-27 16:09:49 -07:00
Vlad Yasevich
328fc47ea0 sctp: correct bounds check in sctp_setsockopt_auth_key
The bonds check to prevent buffer overlflow was not exactly
right.  It still allowed overflow of up to 8 bytes which is
sizeof(struct sctp_authkey).

Since optlen is already checked against the size of that struct,
we are guaranteed not to cause interger overflow either.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-08-27 16:08:54 -07:00
Vlad Yasevich
30c2235cbc sctp: add verification checks to SCTP_AUTH_KEY option
The structure used for SCTP_AUTH_KEY option contains a
length that needs to be verfied to prevent buffer overflow
conditions.  Spoted by Eugene Teo <eteo@redhat.com>.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-08-25 15:16:19 -07:00
Vlad Yasevich
5e739d1752 sctp: fix potential panics in the SCTP-AUTH API.
All of the SCTP-AUTH socket options could cause a panic
if the extension is disabled and the API is envoked.

Additionally, there were some additional assumptions that
certain pointers would always be valid which may not
always be the case.

This patch hardens the API and address all of the crash
scenarios.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-08-21 03:34:25 -07:00
Brian Haley
191cd58250 netns: Add network namespace argument to rt6_fill_node() and ipv6_dev_get_saddr()
ipv6_dev_get_saddr() blindly de-references dst_dev to get the network
namespace, but some callers might pass NULL.  Change callers to pass a
namespace pointer instead.

Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-08-14 15:33:21 -07:00
Herbert Xu
f880374c2f sctp: Drop ipfargok in sctp_xmit function
The ipfragok flag controls whether the packet may be fragmented
either on the local host on beyond.  The latter is only valid on
IPv4.

In fact, we never want to do the latter even on IPv4 when PMTU is
enabled.  This is because even though we can't fragment packets
within SCTP due to the prtocol's inherent faults, we can still
fragment it at IP layer.  By setting the DF bit we will improve
the PMTU process.

RFC 2960 only says that we SHOULD clear the DF bit in this case,
so we're compliant even if we set the DF bit.  In fact RFC 4960
no longer has this statement.

Once we make this change, we only need to control the local
fragmentation.  There is already a bit in the skb which controls
that, local_df.  So this patch sets that instead of using the
ipfragok argument.

The only complication is that there isn't a struct sock object
per transport, so for IPv4 we have to resort to changing the
pmtudisc field for every packet.  This should be safe though
as the protocol is single-threaded.

Note that after this patch we can remove ipfragok from the rest
of the stack too.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-08-03 21:15:08 -07:00
Linus Torvalds
2284284281 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  netns: fix ip_rt_frag_needed rt_is_expired
  netfilter: nf_conntrack_extend: avoid unnecessary "ct->ext" dereferences
  netfilter: fix double-free and use-after free
  netfilter: arptables in netns for real
  netfilter: ip{,6}tables_security: fix future section mismatch
  selinux: use nf_register_hooks()
  netfilter: ebtables: use nf_register_hooks()
  Revert "pkt_sched: sch_sfq: dump a real number of flows"
  qeth: use dev->ml_priv instead of dev->priv
  syncookies: Make sure ECN is disabled
  net: drop unused BUG_TRAP()
  net: convert BUG_TRAP to generic WARN_ON
  drivers/net: convert BUG_TRAP to generic WARN_ON
2008-07-26 20:17:56 -07:00
Ilpo Järvinen
547b792cac net: convert BUG_TRAP to generic WARN_ON
Removes legacy reinvent-the-wheel type thing. The generic
machinery integrates much better to automated debugging aids
such as kerneloops.org (and others), and is unambiguous due to
better naming. Non-intuively BUG_TRAP() is actually equal to
WARN_ON() rather than BUG_ON() though some might actually be
promoted to BUG_ON() but I left that to future.

I could make at least one BUILD_BUG_ON conversion.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-25 21:43:18 -07:00
Ulrich Drepper
a677a039be flag parameters: socket and socketpair
This patch adds support for flag values which are ORed to the type passwd
to socket and socketpair.  The additional code is minimal.  The flag
values in this implementation can and must match the O_* flags.  This
avoids overhead in the conversion.

The internal functions sock_alloc_fd and sock_map_fd get a new parameters
and all callers are changed.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
#include <fcntl.h>
#include <stdio.h>
#include <unistd.h>
#include <netinet/in.h>
#include <sys/socket.h>

#define PORT 57392

/* For Linux these must be the same.  */
#define SOCK_CLOEXEC O_CLOEXEC

int
main (void)
{
  int fd;
  fd = socket (PF_INET, SOCK_STREAM, 0);
  if (fd == -1)
    {
      puts ("socket(0) failed");
      return 1;
    }
  int coe = fcntl (fd, F_GETFD);
  if (coe == -1)
    {
      puts ("fcntl failed");
      return 1;
    }
  if (coe & FD_CLOEXEC)
    {
      puts ("socket(0) set close-on-exec flag");
      return 1;
    }
  close (fd);

  fd = socket (PF_INET, SOCK_STREAM|SOCK_CLOEXEC, 0);
  if (fd == -1)
    {
      puts ("socket(SOCK_CLOEXEC) failed");
      return 1;
    }
  coe = fcntl (fd, F_GETFD);
  if (coe == -1)
    {
      puts ("fcntl failed");
      return 1;
    }
  if ((coe & FD_CLOEXEC) == 0)
    {
      puts ("socket(SOCK_CLOEXEC) does not set close-on-exec flag");
      return 1;
    }
  close (fd);

  int fds[2];
  if (socketpair (PF_UNIX, SOCK_STREAM, 0, fds) == -1)
    {
      puts ("socketpair(0) failed");
      return 1;
    }
  for (int i = 0; i < 2; ++i)
    {
      coe = fcntl (fds[i], F_GETFD);
      if (coe == -1)
        {
          puts ("fcntl failed");
          return 1;
        }
      if (coe & FD_CLOEXEC)
        {
          printf ("socketpair(0) set close-on-exec flag for fds[%d]\n", i);
          return 1;
        }
      close (fds[i]);
    }

  if (socketpair (PF_UNIX, SOCK_STREAM|SOCK_CLOEXEC, 0, fds) == -1)
    {
      puts ("socketpair(SOCK_CLOEXEC) failed");
      return 1;
    }
  for (int i = 0; i < 2; ++i)
    {
      coe = fcntl (fds[i], F_GETFD);
      if (coe == -1)
        {
          puts ("fcntl failed");
          return 1;
        }
      if ((coe & FD_CLOEXEC) == 0)
        {
          printf ("socketpair(SOCK_CLOEXEC) does not set close-on-exec flag for fds[%d]\n", i);
          return 1;
        }
      close (fds[i]);
    }

  puts ("OK");

  return 0;
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:27 -07:00
Adrian Bunk
4d6971e909 sctp: remove sctp_assoc_proc_exit()
Commit 20c2c1fd6c
(sctp: add sctp/remaddr table to complete RFC remote address table OID)
added an unused sctp_assoc_proc_exit() function that seems to have been 
unintentionally created when copying the assocs code.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-22 14:21:30 -07:00
Adrian Bunk
abd0b198ea sctp: make sctp_outq_flush() static
sctp_outq_flush() can now become static.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-22 14:20:45 -07:00
YOSHIFUJI Hideaki
721499e893 netns: Use net_eq() to compare net-namespaces for optimization.
Without CONFIG_NET_NS, namespace is always &init_net.
Compiler will be able to omit namespace comparisons with this patch.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-19 22:34:43 -07:00
Vlad Yasevich
845525a642 sctp: Update sctp global memory limit allocations.
Update sctp global memory limit allocations to be the same as TCP.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-18 23:08:21 -07:00
Harvey Harrison
336d3262df sctp: remove unnecessary byteshifting, calculate directly in big-endian
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-18 23:07:09 -07:00
Vlad Yasevich
4e54064e0a sctp: Allow only 1 listening socket with SO_REUSEADDR
When multiple socket bind to the same port with SO_REUSEADDR,
only 1 can be listining.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-18 23:06:32 -07:00
Vlad Yasevich
23b29ed80b sctp: Do not leak memory on multiple listen() calls
SCTP permits multiple listen call and on subsequent calls
we leak he memory allocated for the crypto transforms.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-18 23:06:07 -07:00
Vlad Yasevich
7dab83de50 sctp: Support ipv6only AF_INET6 sockets.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-18 23:05:40 -07:00
Florian Westphal
6d0ccbac68 sctp: Prevent uninitialized memory access
valgrind reports uninizialized memory accesses when running
sctp inside the network simulation cradle simulator:

 Conditional jump or move depends on uninitialised value(s)
    at 0x570E34A: sctp_assoc_sync_pmtu (associola.c:1324)
    by 0x57427DA: sctp_packet_transmit (output.c:403)
    by 0x5710EFF: sctp_outq_flush (outqueue.c:824)
    by 0x5710B88: sctp_outq_uncork (outqueue.c:701)
    by 0x5745262: sctp_cmd_interpreter (sm_sideeffect.c:1548)
    by 0x57444B7: sctp_side_effects (sm_sideeffect.c:976)
    by 0x5744460: sctp_do_sm (sm_sideeffect.c:945)
    by 0x572157D: sctp_primitive_ASSOCIATE (primitive.c:94)
    by 0x5725C04: __sctp_connect (socket.c:1094)
    by 0x57297DC: sctp_connect (socket.c:3297)

 Conditional jump or move depends on uninitialised value(s)
    at 0x575D3A5: mod_timer (timer.c:630)
    by 0x5752B78: sctp_cmd_hb_timers_start (sm_sideeffect.c:555)
    by 0x5754133: sctp_cmd_interpreter (sm_sideeffect.c:1448)
    by 0x5753607: sctp_side_effects (sm_sideeffect.c:976)
    by 0x57535B0: sctp_do_sm (sm_sideeffect.c:945)
    by 0x571E9AE: sctp_endpoint_bh_rcv (endpointola.c:474)
    by 0x573347F: sctp_inq_push (inqueue.c:104)
    by 0x572EF93: sctp_rcv (input.c:256)
    by 0x5689623: ip_local_deliver_finish (ip_input.c:230)
    by 0x5689759: ip_local_deliver (ip_input.c:268)
    by 0x5689CAC: ip_rcv_finish (dst.h:246)

#1 is due to "if (t->pmtu_pending)".
8a4794914f "[SCTP] Flag a pmtu change request"
suggests it should be initialized to 0.

#2 is the heartbeat timer 'expires' value, which is uninizialised, but
test by mod_timer().
T3_rtx_timer seems to be affected by the same problem, so initialize it, too.

Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-18 23:04:39 -07:00
Florian Westphal
c4e85f82ed sctp: Don't abort initialization when CONFIG_PROC_FS=n
This puts CONFIG_PROC_FS defines around the proc init/exit functions
and also avoids compiling proc.c if procfs is not supported.
Also make SCTP_DBG_OBJCNT depend on procfs.

Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-18 23:03:44 -07:00
Pavel Emelyanov
de0744af1f mib: add net to NET_INC_STATS_BH
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-16 20:31:16 -07:00
Pavel Emelyanov
5c52ba170f sock: add net to prot->enter_memory_pressure callback
The tcp_enter_memory_pressure calls NET_INC_STATS, but doesn't
have where to get the net from.

I decided to add a sk argument, not the net itself, only to factor
all the required sock_net(sk) calls inside the enter_memory_pressure 
callback itself.

Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-16 20:28:10 -07:00
Pavel Emelyanov
7c73a6faff mib: add net to IP_INC_STATS_BH
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-16 20:20:11 -07:00
Pavel Emelyanov
dcfc23cac1 mib: add struct net to ICMP_INC_STATS_BH
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-14 23:05:29 -07:00
David S. Miller
7c3ceb4a40 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:

	drivers/net/wireless/iwlwifi/iwl-3945.c
	net/mac80211/mlme.c
2008-07-08 16:30:17 -07:00
Vlad Yasevich
3888e9efc9 sctp: Mark the tsn as received after all allocations finish
If we don't have the buffer space or memory allocations fail,
the data chunk is dropped, but TSN is still reported as received.
This introduced a data loss that can't be recovered.  We should
only mark TSNs are received after memory allocations finish.
The one exception is the invalid stream identifier, but that's
due to user error and is reported back to the user.

This was noticed by Michael Tuexen.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-08 02:28:39 -07:00
Vlad Yasevich
ecbed6a419 sctp: Mark GET_PEER|LOCAL_ADDR_OLD deprecated.
Socket options SCTP_GET_PEER_ADDR_OLD, SCTP_GET_PEER_ADDR_NUM_OLD,
SCTP_GET_LOCAL_ADDR_OLD, and SCTP_GET_PEER_LOCAL_ADDR_NUM_OLD
have been replaced by newer versions a since 2005.  It's time
to officially deprecate them and schedule them for removal.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-01 20:06:22 -07:00
David S. Miller
1b63ba8a86 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:

	drivers/net/wireless/iwlwifi/iwl4965-base.c
2008-06-28 01:19:40 -07:00
David S. Miller
735ce972fb sctp: Make sure N * sizeof(union sctp_addr) does not overflow.
As noticed by Gabriel Campana, the kmalloc() length arg
passed in by sctp_getsockopt_local_addrs_old() can overflow
if ->addr_num is large enough.

Therefore, enforce an appropriate limit.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-20 22:04:34 -07:00
Vlad Yasevich
0f474d9bc5 sctp: Kill unused variable in sctp_assoc_bh_rcv()
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-20 10:34:47 -07:00
Vlad Yasevich
2e3216cd54 sctp: Follow security requirement of responding with 1 packet
RFC 4960, Section 11.4. Protection of Non-SCTP-Capable Hosts

When an SCTP stack receives a packet containing multiple control or
DATA chunks and the processing of the packet requires the sending of
multiple chunks in response, the sender of the response chunk(s) MUST
NOT send more than one packet.  If bundling is supported, multiple
response chunks that fit into a single packet MAY be bundled together
into one single response packet.  If bundling is not supported, then
the sender MUST NOT send more than one response chunk and MUST
discard all other responses.  Note that this rule does NOT apply to a
SACK chunk, since a SACK chunk is, in itself, a response to DATA and
a SACK does not require a response of more DATA.

We implement this by not servicing our outqueue until we reach the end
of the packet.  This enables maximum bundling.  We also identify
'response' chunks and make sure that we only send 1 packet when sending
such chunks.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-19 16:08:18 -07:00
Wei Yongjun
7115e632f9 sctp: Validate Initiate Tag when handling ICMP message
This patch add to validate initiate tag and chunk type if verification
tag is 0 when handling ICMP message.

RFC 4960, Appendix C. ICMP Handling

ICMP6) An implementation MUST validate that the Verification Tag
contained in the ICMP message matches the Verification Tag of the peer.
If the Verification Tag is not 0 and does NOT match, discard the ICMP
message.  If it is 0 and the ICMP message contains enough bytes to
verify that the chunk type is an INIT chunk and that the Initiate Tag
matches the tag of the peer, continue with ICMP7.  If the ICMP message
is too short or the chunk type or the Initiate Tag does not match,
silently discard the packet.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-19 16:07:48 -07:00
Pavel Emelyanov
3d00fb9eb1 sctp: fix error path in sctp_proc_init
After the sctp_remaddr_proc_init failed, the proper rollback is
not the sctp_remaddr_proc_exit, but the sctp_assocs_proc_exit.

Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-17 15:54:14 -07:00
David S. Miller
caea902f72 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:

	drivers/net/wireless/rt2x00/Kconfig
	drivers/net/wireless/rt2x00/rt2x00usb.c
	net/sctp/protocol.c
2008-06-16 18:25:48 -07:00