Fix some device tree omissions that prevented the new EMAC driver from
setting up ethernet on the Bamboo board correctly and update the Bamboo
defconfig.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch enables NEW EMAC support for PowerPC 440EPx Sequoia board.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds RGMII support to Sequoia DTS and sets correct phy-mode
for EMACs. According to Sequoia datasheet, both ethernet ports
are connected to RGMII interface, while ZMII is used only for MDIO.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (408 commits)
[POWERPC] Add memchr() to the bootwrapper
[POWERPC] Implement logging of unhandled signals
[POWERPC] Add legacy serial support for OPB with flattened device tree
[POWERPC] Use 1TB segments
[POWERPC] XilinxFB: Allow fixed framebuffer base address
[POWERPC] XilinxFB: Add support for custom screen resolution
[POWERPC] XilinxFB: Use pdata to pass around framebuffer parameters
[POWERPC] PCI: Add 64-bit physical address support to setup_indirect_pci
[POWERPC] 4xx: Kilauea defconfig file
[POWERPC] 4xx: Kilauea DTS
[POWERPC] 4xx: Add AMCC Kilauea eval board support to platforms/40x
[POWERPC] 4xx: Add AMCC 405EX support to cputable.c
[POWERPC] Adjust TASK_SIZE on ppc32 systems to 3GB that are capable
[POWERPC] Use PAGE_OFFSET to tell if an address is user/kernel in SW TLB handlers
[POWERPC] 85xx: Enable FP emulation in MPC8560 ADS defconfig
[POWERPC] 85xx: Killed <asm/mpc85xx.h>
[POWERPC] 85xx: Add cpm nodes for 8541/8555 CDS
[POWERPC] 85xx: Convert mpc8560ads to the new CPM binding.
[POWERPC] mpc8272ads: Remove muram from the CPM reg property.
[POWERPC] Make clockevents work on PPC601 processors
...
Fixed up conflict in Documentation/powerpc/booting-without-of.txt manually.
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs. The
same ASIC is also found in the Axon bridge chip. This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging. Specifically:
- Should be adjusted to properly use the dma mapping API.
Axon needs this.
- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices. The dependencies here between
EMAC, MAL, ZMII etc. make this complicated. At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Commit 804ace8881 changed the behavior of how compatible nodes are found.
This highlighted a bug on the Bamboo board where it wasn't probing the bus
specified in the DTS file. We fix it by being explicit about which bus to
probe.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbvear.id.au>
This patch corrects a number of minor errors in the Ebony device tree:
- Missing (given as 0) cache sizes are added to the CPU node
- device_type properties are removed from nodes which don't
have a reasonably well defined device_type binding. This does require
a very small code change to locate the busses to be probed for
of_platform devices by 'compatible' instead of 'device_type'.
- A node is added for the SRAM controller
- The unit address of the small-flash node is adjusted to
correctly reflect the reg property.
- device_type values for the MAL and ZMII are updated to
reflected more up-to-date versions of the binding.
- An incorrect offset in the partition map for the large-flash
node is corrected.
- Some redundant values, already commented out are removed
entirely.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
An allmodconfig on the current powerpc tree yields:
arch/powerpc/platforms/44x/Kconfig:41:warning: 'select' used by
config symbol '440GP' refers to undefined symbol 'IBM_NEW_EMAC_ZMII'
Hide the select until the driver exists.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds support for early serial debugging via the built in
port on IBM/AMCC PowerPC 44x CPUs. It uses a bolted TLB entry in
address space 1 for the UART's mapping, allowing robust debugging both
before and after the initialization of the MMU.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds platform support code for the Ebony (440GP) evaluation
board. This includes both code in arch/powerpc/platforms/44x for
board initialization, and zImage wrapper code to correctly tweak the
flattened device tree based on information from the firmware. The
zImage supports both IBM OpenBIOS (aka "treeboot") and old versions of
uboot which don't support a flattened device tree.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This prepares for Ebony/440 support by creating an
arch/powerpc/platforms/44x directory. It is populated with a single
misc_44x.S file, into which is moved the 44x specific reset code from
head_44x.S (on the grounds that we should really stop clogging up the
head_* files with random asm helper routines).
At the same time, we disable the (empty save Kconfig and Makefile)
arch/powerpc/platforms/4xx directory from the arch/powerpc/platforms
Makefile. Contrary to the comment in
arch/powerpc/platforms/4xx/Makefile, attempting to build such an empty
Makefile will fail, thus breaking compile for the 44x platforms we're
about to add. It can go back in once we start porting some of the 40x
platforms (and thus it becomes non-empty).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
