Change the PHY clock divisor to make the MDIO clock 2.5MHz, instead of
3.5MHz (which is out of spec).
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Faisal Latif <Faisal.Latif@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add a missing 16-bit reserved field between ap_status and info fields.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
For IBoE, SLs 0-7 are mapped to Ethernet 802.1Q user priority bits
(pbits) which are part of the VLAN tag, SLs 8-15 are reserved.
Under Ethernet, the ConnectX firmware treats (decode/encode) the four
bit SL field in various constructs such as QPC / UD WQE / CQE as PPP0
and not as 0PPP. This correlates well to the fact that within the
vlan tag the pbits are located in bits 15-13 and not 12-14.
The current code wasn't consistent around that area - the
encoding was correct for the IBoE QPC.path.schedule_queue field,
but was wrong for IBoE CQEs and when MLX header was built.
These inconsistencies resulted in wrong SL <--> wire 802.1Q pbits
mapping, which is fixed by using SL <--> PPP0 all around the place.
Signed-off-by: Oren Duer <oren@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Minimize the need for users to have to set module parameters to get
good performance.
The following two parameters are changed:
- rcvhdrcnt to twice the rcvegrcnt
- pcie_caps=0x51
The rcvhdrcnt at twice the egrcount allows the preemptive NAK code
during reception to function in 100% of the cases rather than a sender
jiffies-based timeout.
The pcie_caps default of 0x51 will set the proposed MaxPayload and
MaxReceiveReqest to 256 and 4096 respectively. The capabilities on
the root complex will be used to limit those values.
Reviewed-by: Ram Vepa <ram.vepa@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The current code locks the QP s_lock, followed by the pending_lock, I
guess to to protect against the allocate failing.
This patch only locks the pending_lock, assuming that the empty case
is an exeception, in which case the pending_lock is dropped, and the
original code is executed. This will save a lock of s_lock in the
normal case.
The observation is that the sdma descriptors will deplete at twice the
rate of txreq's, so this should be rare.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Prevent a receive data corruption by ensuring that the write to update
the rcvhdrheadn register to generate an interrupt is at the very end
of the receive processing.
Signed-off-by: Ramkrishna Vepa <ram.vepa@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The qib driver makes use of the the 64-bit jiffies API.
Code inspection reveals that that version of the API is not really
required. This patch converts to use the "normal" jiffies.
Reviewed-by: Ram Vepa <ram.vepa@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
More style issues revealed with checkpatch.pl -f.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Userspace verbs multicast attach/detach operations on a QP are done
while holding the rwsem of the QP for reading. That's not sufficient
since a reader lock allows more than one reader to acquire the
lock. However, multicast attach/detach does list manipulation that
can corrupt the list if multiple threads run in parallel.
Fix this by acquiring the rwsem as a writer to serialize attach/detach
operations. Add idr_write_qp() and put_qp_write() to encapsulate
this.
This fixes oops seen when running applications that perform multicast
joins/leaves.
Reported by: Mike Dubman <miked@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
both callers of device_get_devnode() are only interested in lower 16bits
and nobody tries to return anything wider than 16bit anyway.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Conflicts:
net/bluetooth/l2cap_core.c
Just two overlapping changes, one added an initialization of
a local variable, and another change added a new local variable.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 53ab1c6498 ("IB/qib: Correct nfreectxts for multiple HCAs")
reversed the increments and decrements of dd->nfreectxts. Fix it.
Reviewed-by: Ram Vepa <ram.vepa@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
private_data_len is defined as a u8. If the user specifies a large
private_data size (> 220 bytes), we will calculate a total length that
exceeds 255, resulting in private_data_len wrapping back to 0. This
can lead to overwriting random kernel memory. Avoid this by verifying
that the resulting size fits into a u8.
Reported-by: B. Thery <benjamin.thery@bull.net>
Addresses: <http://bugs.openfabrics.org/bugzilla/show_bug.cgi?id=2335>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch adds the kernel module ib_srpt SCSI RDMA Protocol (SRP) target
implementation conforming to the SRP r16a specification for the mainline
drivers/target infrastructure.
This driver was originally developed by Vu Pham and has been optimized by
Bart Van Assche and merged into upstream LIO based on his srpt-lio-4.1
branch here:
https://github.com/bvanassche/srpt-lio/commits/srpt-lio-4.1/
This updated patch also contains the following two changes from
lio-core-2.6.git/master. One is to fix a bug with 1 >= task->task_sg[]
chained mappings in ib_srpt, and the other to convert the configfs control
plane to reference IB Port GUID and struct srpt_port directly following
mainline v4.x target_core_fabric_configfs.c convertion for ib_srpt
to work with rtslib/rtsadmin v2 code.
These seperate patches can be found here:
ib_srpt: Fix bug with chainged SGLs in srpt_map_sg_to_ib_sge
http://www.risingtidesystems.com/git/?p=lio-core-2.6.git;a=commitdiff;h=ea485147563b6555a97dbf811825fbb586519252
ib_srpt: Convert se_wwn endpoint reference to struct srpt_port->port_wwn
http://www.risingtidesystems.com/git/?p=lio-core-2.6.git;a=commitdiff;h=4e544a210acb227df1bb4ca5086e65bdf4e648ea
This also includes the following recent v1 -> v2 review changes:
ib_srpt: Fix potential out-of-bounds array access
ib_srpt: Avoid failed multipart RDMA transfers
ib_srpt: Fix srpt_alloc_fabric_acl failure case return value
ib_srpt: Update comments to reference $driver/$port layout
ib_srpt: Fix sport->port_guid formatting code
ib_srpt: Remove legacy use_port_guid_in_session_name module parameter
ib_srpt: Convert srp_max_rdma_size into per port configfs attribute
ib_srpt: Convert srp_max_rsp_size into per port configfs attribute
ib_srpt: Convert srpt_sq_size into per port configfs attribute
and v2 -> v3 review changes:
ib_srpt: Fix possible race with srp_sq_size in srpt_create_ch_ib
ib_srpt: Fix possible race with srp_max_rsp_size in srpt_release_channel_work
ib_srpt: Fix up MAX_SRPT_RDMA_SIZE define
ib_srpt: Make srpt_map_sg_to_ib_sge() failure case return -EAGAIN
ib_srpt: Convert port_guid to use subnet_prefix + interface_id formatting
ib_srpt: Make srpt_check_stop_free return kref_put status
ib_srpt: Make compilation with BUG=n proceed`
ib_srpt: Use new target_core_fabric.h include
ib_srpt: Check hex2bin() return code to silence build warning
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Vu Pham <vu@mellanox.com>
Cc: David Dillow <dillowda@ornl.gov>
Signed-off-by: Nicholas A. Bellinger <nab@risingtidesystems.com>
For SRIOV, some Hypervisor commands can be executed directly (native = 1).
Others should go through the command wrapper flow (for tracking resource
usage, for example, or for changing some HCA configurations that slaves
need to be notified of).
This patch sets the groundwork for this capability -- adding the correct
value of "native" in each case.
Note that if SRIOV is not activated, this parameter has no effect.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port mask now has additional state.
Port can be set as "none". In this case neither the mlx4_en or mlx4_ib
drivers take ownership of the port.
In multifunction mode there is an option to set the vfs as single ported devices.
(in single function mode, both physical ports belong to same function)
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit cfcde11c3d ("IB/mlx4: Use flow counters on IBoE ports") added
code that sets elements of counters[] to -1 if no counter is allocated,
but then goes ahead and passes every entry to mlx4_counter_free() on
shutdown. This is a bad idea, especially if MLX4_DEV_CAP_FLAG_COUNTERS
isn't set so there isn't even an underlying bitmap to free from.
Tested-by: Sean Hefty <sean.hefty@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reduce the number of dst_get_neighbour_noref() calls within a single
call chain. Primarily by passing the neighbour pointer down to the
helper functions.
Handle dst_get_neighbour_noref() returning NULL in ipoib_start_xmit()
by incrementing the dropped counter and freeing the packet. We don't
want it to fall through into the ARP/RARP/multicast handling, since
that should only happen when skb_dst() is NULL.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Roland Dreier <roland@purestorage.com>
Three pieces of code do the same thing, create a l2t entry and then
import this information into the c4iw_ep object.
Create a helper function and call it from these 3 locations instead.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Roland Dreier <roland@purestorage.com>
This way we consolidate the RCU locking down into the place where it
actually matters, and also we can make the code handle
dst_get_neighbour_noref() returning NULL properly.
Signed-off-by: David S. Miller <davem@davemloft.net>
IPV4 should do exactly what the IPV6 code does here, which is
use the neighbour obtained via the dst entry.
And now that the two code paths do the same thing, use a common
helper function to perform the operation.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Roland Dreier <roland@purestorage.com>
To reflect the fact that a refrence is not obtained to the
resulting neighbour entry.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Roland Dreier <roland@purestorage.com>
netdev->neigh_priv_len records the private area length.
This will trigger for neigh_table objects which set tbl->entry_size
to zero, and the first instances of this will be forthcoming.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f2c31e32b3 ("net: fix NULL dereferences in check_peer_redir()")
forgot to take care of infiniband uses of dst neighbours.
Many thanks to Marc Aurele who provided a nice bug report and feedback.
Reported-by: Marc Aurele La France <tsi@ualberta.ca>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This following can occur with ipoib when processing a multicast reponse:
BUG: soft lockup - CPU#0 stuck for 67s! [ib_mad1:982]
Modules linked in: ...
CPU 0:
Modules linked in: ...
Pid: 982, comm: ib_mad1 Not tainted 2.6.32-131.0.15.el6.x86_64 #1 ProLiant DL160 G5
RIP: 0010:[<ffffffff814ddb27>] [<ffffffff814ddb27>] _spin_unlock_irqrestore+0x17/0x20
RSP: 0018:ffff8802119ed860 EFLAGS: 00000246
0000000000000004 RBX: ffff8802119ed860 RCX: 000000000000a299
RDX: ffff88021086c700 RSI: 0000000000000246 RDI: 0000000000000246
RBP: ffffffff8100bc8e R08: ffff880210ac229c R09: 0000000000000000
R10: ffff88021278aab8 R11: 0000000000000000 R12: ffff8802119ed860
R13: ffffffff8100be6e R14: 0000000000000001 R15: 0000000000000003
FS: 0000000000000000(0000) GS:ffff880028200000(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 00000000006d4840 CR3: 0000000209aa5000 CR4: 00000000000406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Call Trace:
[<ffffffffa032c247>] ? ipoib_mcast_send+0x157/0x480 [ib_ipoib]
[<ffffffff8100bc8e>] ? apic_timer_interrupt+0xe/0x20
[<ffffffff8100bc8e>] ? apic_timer_interrupt+0xe/0x20
[<ffffffffa03283d4>] ? ipoib_path_lookup+0x124/0x2d0 [ib_ipoib]
[<ffffffffa03286fc>] ? ipoib_start_xmit+0x17c/0x430 [ib_ipoib]
[<ffffffff8141e758>] ? dev_hard_start_xmit+0x2c8/0x3f0
[<ffffffff81439d0a>] ? sch_direct_xmit+0x15a/0x1c0
[<ffffffff81423098>] ? dev_queue_xmit+0x388/0x4d0
[<ffffffffa032d6b7>] ? ipoib_mcast_join_finish+0x2c7/0x510 [ib_ipoib]
[<ffffffffa032dab8>] ? ipoib_mcast_sendonly_join_complete+0x1b8/0x1f0 [ib_ipoib]
[<ffffffffa02a0946>] ? mcast_work_handler+0x1a6/0x710 [ib_sa]
[<ffffffffa015f01e>] ? ib_send_mad+0xfe/0x3c0 [ib_mad]
[<ffffffffa00f6c93>] ? ib_get_cached_lmc+0xa3/0xb0 [ib_core]
[<ffffffffa02a0f9b>] ? join_handler+0xeb/0x200 [ib_sa]
[<ffffffffa029e4fc>] ? ib_sa_mcmember_rec_callback+0x5c/0xa0 [ib_sa]
[<ffffffffa029e79c>] ? recv_handler+0x3c/0x70 [ib_sa]
[<ffffffffa01603a4>] ? ib_mad_completion_handler+0x844/0x9d0 [ib_mad]
[<ffffffffa015fb60>] ? ib_mad_completion_handler+0x0/0x9d0 [ib_mad]
[<ffffffff81088830>] ? worker_thread+0x170/0x2a0
[<ffffffff8108e160>] ? autoremove_wake_function+0x0/0x40
[<ffffffff810886c0>] ? worker_thread+0x0/0x2a0
[<ffffffff8108ddf6>] ? kthread+0x96/0xa0
[<ffffffff8100c1ca>] ? child_rip+0xa/0x20
Coinciding with stack trace is the following message:
ib0: ib_address_create failed
The code below in ipoib_mcast_join_finish() will note the above
failure in the address handle but otherwise continue:
ah = ipoib_create_ah(dev, priv->pd, &av);
if (!ah) {
ipoib_warn(priv, "ib_address_create failed\n");
} else {
The while loop at the bottom of ipoib_mcast_join_finish() will attempt
to send queued multicast packets in mcast->pkt_queue and eventually
end up in ipoib_mcast_send():
if (!mcast->ah) {
if (skb_queue_len(&mcast->pkt_queue) < IPOIB_MAX_MCAST_QUEUE)
skb_queue_tail(&mcast->pkt_queue, skb);
else {
++dev->stats.tx_dropped;
dev_kfree_skb_any(skb);
}
My read is that the code will requeue the packet and return to the
ipoib_mcast_join_finish() while loop and the stage is set for the
"hung" task diagnostic as the while loop never sees a non-NULL ah, and
will do nothing to resolve.
There are GFP_ATOMIC allocates in the provider routines, so this is
possible and should be dealt with.
The test that induced the failure is associated with a host SM on the
same server during a shutdown.
This patch causes ipoib_mcast_join_finish() to exit with an error
which will flush the queued mcast packets. Nothing is done to unwind
the QP attached state so that subsequent sends from above will retry
the join.
Reviewed-by: Ram Vepa <ram.vepa@qlogic.com>
Reviewed-by: Gary Leshner <gary.leshner@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Don't over-schedule QSFP work on driver initialization. It could end
up being run simultaneously on two different CPUs resulting in bad
EEPROM reads. In combination with setting the physical IB link state
prior to the IBC being brought out of reset, this can cause the link
state machine to start training early with wrong settings.
Signed-off-by: Mitko Haralanov <mitko@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix logic so that we don't retry with MPAv1 once we have done that
already. Otherwise, we end up retrying with MPAv1 even when its not
needed on getting peer aborts - and this could lead to kernel panic.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix another place in the code where logic dealing with the t4_cqe was
using the wrong QID. This fixes the counting logic so that it tests
against the SQ QID instead of the RQ QID when counting RCQES.
Signed-off by: Jonathan Lallinger <jonathan@ogc.us>
Signed-off by: Steve Wise <swise@ogc.us>
Signed-off-by: Roland Dreier <roland@purestorage.com>
C assignment can handle struct in6_addr copying.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was mistakenly introduced by dde05cbdf8 ("IB/qib: Hold links
until tuning data is available").
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
The following panic can occur when flushing a QP:
RIP: 0010:[<ffffffffa0168e8b>] [<ffffffffa0168e8b>] qib_send_complete+0x3b/0x190 [ib_qib]
RSP: 0018:ffff8803cdc6fc90 EFLAGS: 00010046
RAX: 0000000000000000 RBX: ffff8803d84ba000 RCX: 0000000000000000
RDX: 0000000000000005 RSI: ffffc90015a53430 RDI: ffff8803d84ba000
RBP: ffff8803cdc6fce0 R08: ffff8803cdc6fc90 R09: 0000000000000001
R10: 00000000ffffffff R11: 0000000000000000 R12: ffff8803d84ba0c0
R13: ffff8803d84ba5cc R14: 0000000000000800 R15: 0000000000000246
FS: 0000000000000000(0000) GS:ffff880036600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000034 CR3: 00000003e44f9000 CR4: 00000000000406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process qib/0 (pid: 1350, threadinfo ffff8803cdc6e000, task ffff88042728a100)
Stack:
53544c5553455201 0000000100000005 0000000000000000 ffff8803d84ba000
0000000000000000 0000000000000000 0000000000000000 0000000000000000
0000000000000000 0000000000000001 ffff8803cdc6fd30 ffffffffa0165d7a
Call Trace:
[<ffffffffa0165d7a>] qib_make_rc_req+0x36a/0xe80 [ib_qib]
[<ffffffffa0165a10>] ? qib_make_rc_req+0x0/0xe80 [ib_qib]
[<ffffffffa01698b3>] qib_do_send+0xf3/0xb60 [ib_qib]
[<ffffffff814db757>] ? thread_return+0x4e/0x777
[<ffffffffa01697c0>] ? qib_do_send+0x0/0xb60 [ib_qib]
[<ffffffff81088bf0>] worker_thread+0x170/0x2a0
[<ffffffff8108e530>] ? autoremove_wake_function+0x0/0x40
[<ffffffff81088a80>] ? worker_thread+0x0/0x2a0
[<ffffffff8108e1c6>] kthread+0x96/0xa0
[<ffffffff8100c1ca>] child_rip+0xa/0x20
[<ffffffff8108e130>] ? kthread+0x0/0xa0
[<ffffffff8100c1c0>] ? child_rip+0x0/0x20
RIP [<ffffffffa0168e8b>] qib_send_complete+0x3b/0x190 [ib_qib]
The RC error state flush logic in qib_make_rc_req() could return all
of the acked wqes and potentially have emptied the queue. It would
then unconditionally try return a flush completion via
qib_send_complete() for an invalid wqe, or worse a valid one that is
not queued. The panic results when the completion code tries to
maintain an MR reference count for a NULL MR.
This fix modifies logic to only send one completion per
qib_make_rc_req() call and changing the completion status from
IB_WC_SUCCESS to IB_WC_WR_FLUSH_ERR as the completions progress.
The outer loop will call as many times as necessary to flush the queue.
Reviewed-by: Ram Vepa <ram.vepa@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The current driver never does DMA unmapping on these buffers. Fix that
by adding DMA unmapping to the task cleanup callback, and DMA mapping to
the task init function (drop the headers_initialized micro-optimization).
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The driver counted on the transactional nature of iSCSI login/text
flows and used the same buffer for both the request and the response.
We also went further and did DMA mapping only once, with
DMA_FROM_DEVICE, which violates the DMA mapping API. Fix that by
using different buffers, one for requests and one for responses, and
use the correct DMA mapping direction for each.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The num_free field of mthca_buddy has a type of array of unsigned int
while it was allocated as an array of pointers. On 64-bit platforms
this allocates twice more than required. Fix this by allocating the
correct size for the type.
This is the same bug just fixed in mlx4 by Eli Cohen <eli@mellanox.co.il>.
Signed-off-by: Roland Dreier <roland@purestorage.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (62 commits)
mlx4_core: Deprecate log_num_vlan module param
IB/mlx4: Don't set VLAN in IBoE WQEs' control segment
IB/mlx4: Enable 4K mtu for IBoE
RDMA/cxgb4: Mark QP in error before disabling the queue in firmware
RDMA/cxgb4: Serialize calls to CQ's comp_handler
RDMA/cxgb3: Serialize calls to CQ's comp_handler
IB/qib: Fix issue with link states and QSFP cables
IB/mlx4: Configure extended active speeds
mlx4_core: Add extended port capabilities support
IB/qib: Hold links until tuning data is available
IB/qib: Clean up checkpatch issue
IB/qib: Remove s_lock around header validation
IB/qib: Precompute timeout jiffies to optimize latency
IB/qib: Use RCU for qpn lookup
IB/qib: Eliminate divide/mod in converting idx to egr buf pointer
IB/qib: Decode path MTU optimization
IB/qib: Optimize RC/UC code by IB operation
IPoIB: Use the right function to do DMA unmap pages
RDMA/cxgb4: Use correct QID in insert_recv_cqe()
RDMA/cxgb4: Make sure flush CQ entries are collected on connection close
...
Some kernel components pin user space memory (infiniband and perf) (by
increasing the page count) and account that memory as "mlocked".
The difference between mlocking and pinning is:
A. mlocked pages are marked with PG_mlocked and are exempt from
swapping. Page migration may move them around though.
They are kept on a special LRU list.
B. Pinned pages cannot be moved because something needs to
directly access physical memory. They may not be on any
LRU list.
I recently saw an mlockalled process where mm->locked_vm became
bigger than the virtual size of the process (!) because some
memory was accounted for twice:
Once when the page was mlocked and once when the Infiniband
layer increased the refcount because it needt to pin the RDMA
memory.
This patch introduces a separate counter for pinned pages and
accounts them seperately.
Signed-off-by: Christoph Lameter <cl@linux.com>
Cc: Mike Marciniszyn <infinipath@qlogic.com>
Cc: Roland Dreier <roland@kernel.org>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These files were getting the moduleparam infrastructure from the
implicit presence of module.h being everywhere, but that is going
away soon.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These were getting it implicitly via device.h --> module.h but
we are going to stop that when we clean up the headers.
Fix these in advance so the tree remains biscect-clean.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
They had been getting it implicitly via device.h but we can't
rely on that for the future, due to a pending cleanup so fix
it now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
They get it via module.h (via device.h) but we want to clean that up.
When we do, we'll get things like:
CC [M] drivers/infiniband/core/sysfs.o
sysfs.c:361: error: 'S_IRUGO' undeclared here (not in a function)
sysfs.c:654: error: 'S_IWUSR' undeclared here (not in a function)
so add in the stat header it is using explicitly in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
There's no need to set the vlan-related fields in an IBoE send WQE
control segment:
- the vlan to be used by a UD QP is set in the datagram segment.
- for GSI (CM) QP, all the headers down to 8021q and MAC are built by
the software anyway.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The IBoE port MTU is derived from the corresponding Ethernet netdevice
MTU, which can support jumbo frames of 9K, and hence surely supports
the max IB mtu of 4K.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
QPs need to be moved to error before telling the firwmare to shutdown
the queue. Otherwise, the application can submit WRs that will never
get fetched by the hardware and never flushed by the driver.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Acked-by: Steve Wise <swsie@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit 01e7da6ba5 ("RDMA/cxgb4: Make sure flush CQ entries are
collected on connection close") introduced a potential problem where a
CQ's comp_handler can get called simultaneously from different places
in the iw_cxgb4 driver. This does not comply with
Documentation/infiniband/core_locking.txt, which states that at a
given point of time, there should be only one callback per CQ should
be active.
This problem was reported by Parav Pandit <Parav.Pandit@Emulex.Com>.
Based on discussion between Parav Pandit and Steve Wise, this patch
fixes the above problem by serializing the calls to a CQ's
comp_handler using a spin_lock.
Reported-by: Parav Pandit <Parav.Pandit@Emulex.Com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
iw_cxgb3 has a potential problem where a CQ's comp_handler can get
called simultaneously from different places in iw_cxgb3 driver. This
does not comply with Documentation/infiniband/core_locking.txt, which
states that at a given point of time, there should be only one
callback per CQ should be active.
Such problem was reported by Parav Pandit <Parav.Pandit@Emulex.Com>
for iw_cxgb4 driver. Based on discussion between Parav Pandit and
Steve Wise, this patch fixes the above problem by serializing the
calls to a CQ's comp_handler using a spin_lock.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix an issue where the link would come up after replugging a cable
even if it has been DISABLED manually.
Signed-off-by: Mitko Haralanov <mitko@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Set the extended active speeds based on the hardware configuration.
Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
[ Move FDR-10 handling into ib_link_query_port(). - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Hold the link state machine until the tuning data is read from the
QSFP EEPROM so correct tuning settings are applied before the state
machine attempts to bring the link up. Link is also held on cable
unplug in case a different cable is used.
Signed-off-by: Mitko Haralanov <mitko@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This was probably present from initial submission.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Review of qib_ruc_check_hdr() shows that the s_lock is not required in
the normal case. The r_lock is held in all cases, and protects the qp
fields that are read.
The s_lock will be needed to around the call to qib_migrate_qp() to
insure that the send engine sees a consistent set of fields.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
A new field is added to qib_qp called timeout_jiffies. It is
initialized upon create and modify.
The field is now used instead of a computation based on qp->timeout.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The heavy weight spinlock in qib_lookup_qpn() is replaced with RCU.
The hash list itself is now accessed via jhash functions instead of mod.
The changes should benefit multiple receive contexts in different
processors by not contending for the lock just to read the hash
structures.
The patch also adds a lookaside_qp (pointer) and a lookaside_qpn in
the context. The interrupt handler will test the current packet's qpn
against lookaside_qpn if the lookaside_qp pointer is non-NULL. The
pointer is NULL'ed when the interrupt handler exits.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The context init now saves a shift from rcvegrbufs_perchunk
rcvegrbufs_perchunk_shift using ilog2. A BUG_ON() protects the
power of 2 assumption.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Store both the encoded and decoded MTU in the QP structure as a minor
optimization for UC/RC receive routines.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The memset for zeroing work completions had been unconditional.
This patch removes the memset and moves the zeroing into the work
completion with a more explicit field by field set. With this patch,
non-ONLY/non-LAST packets will avoid the overhead since they will not
generate a completion.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.
Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pages that were mapped using ib_dma_map_page() should be unmapped
using ib_dma_unmap_page().
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When creating flushed receive CQEs, set the QPID field in the t4_cqe
to the SQ QID and not the RQ QID. Otherwise the poll code will not
find the correct QP context.
Signed-off by: Jonathan Lallinger <jonathan@ogc.us>
Signed-off by: Steve Wise <swise@ogc.us>
Signed-off-by: Roland Dreier <roland@purestorage.com>
At the time when a peer closes the connection, iw_cxgb4 will not send
a cq event if ibqp.uobject exists. In that case, its possible for a
user application to get blocked in ibv_get_cq_event().
To resolve this, call the cq's comp_handler to unblock any read from
ibv_get_cq_event(). This will trigger userspace to poll the cq and
collect flush status completions for any pending work requests.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Allow processes that share the same XRC domain to open an existing
shareable QP. This permits those processes to receive events on the
shared QP and transfer ownership, so that any process may modify the
QP. The latter allows the creating process to exit, while a remaining
process can still transition it for path migration purposes.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
XRC TGT QPs are shared resources among multiple processes. Since the
creating process may exit, allow other processes which share the same
XRC domain to open an existing QP. This allows us to transfer
ownership of an XRC TGT QP to another process.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Support the creation of XRC INI and TGT QPs. To handle the case where
a CQ or PD is not provided, we allocate them internally with the xrcd.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Allow the user to create XRC SRQs. This patch is based on a patch
from Jack Morgenstrein <jackm@dev.mellanox.co.il>.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Support creating and destroying XRC domains. Any sharing of the XRCD
is managed above the low-level driver.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Because an XRC TGT QP can end up being shared among multiple
processes, don't have the ib_cm automatically send a DREQ when the
userspace process that owns the ib_cm_id exits. Disconnect can be
initiated by the user directly; otherwise, the owner of the XRC INI QP
controls the connection.
Note that as a result of the process exiting, the ib_cm will stop
tracking the XRC connection on the target side. For the purposes of
disconnecting, this isn't a big deal. The ib_cm will respond to the
DREQ appropriately. For other messages, mainly LAP, the CM will
reject the request, since there's no one available to route the
request to.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Allow users to connect XRC QPs through the rdma_cm.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Allow the user to indicate the QP type separately from the port space
when allocating an rdma_cm_id. With RDMA_PS_IB, there is no longer a
1:1 relationship between the QP type and port space, so we need to
switch on the QP type to select between UD and connected QPs.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add RDMA_PS_IB. XRC QP types will use the IB port space when operating
over the RDMA CM. For the 'IP protocol' field value, we select 0x3F,
which is listed as being for 'any local network'.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The XRC annex was updated to have XRC behave more like RD. Specifically,
the XRC TGT QPN moves from the local QPN to local EECN field. Lookup of
SRQN is done using the REQ/REP protocol.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Update the REQ and REP messages to support XRC connection setup
according to the XRC Annex. Several existing fields must be set to 0 or
1 when connecting XRC QPs, and a reserved field is changed to an
extended transport type.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Allow user space to operate on XRC TGT QPs the same way as other types
of QPs, with one notable exception: since XRC TGT QPs may be shared
among multiple processes, the XRC TGT QP is allowed to exist beyond the
lifetime of the creating process.
The process that creates the QP is allowed to destroy it, but if the
process exits without destroying the QP, then the QP will be left bound
to the lifetime of the XRCD.
TGT QPs are not associated with CQs or a PD.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
XRC INI QPs are similar to send only RC QPs. Allow user space to create
INI QPs. Note that INI QPs do not require receive CQs.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We require additional information to create XRC SRQs than we can
exchange using the existing create SRQ ABI. Provide an enhanced create
ABI for extended SRQ types.
Based on patches by Jack Morgenstein <jackm@dev.mellanox.co.il>
and Roland Dreier <roland@purestorage.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Allow user space to create XRC domains. Because XRCDs are expected to
be shared among multiple processes, we use inodes to identify an XRCD.
Based on patches by Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
XRC TGT QPs are intended to be shared among multiple users and
processes. Allow the destruction of an XRC TGT QP to be done explicitly
through ib_destroy_qp() or when the XRCD is destroyed.
To support destroying an XRC TGT QP, we need to track TGT QPs with the
XRCD. When the XRCD is destroyed, all tracked XRC TGT QPs are also
cleaned up.
To avoid stale reference issues, if a user is holding a reference on a
TGT QP, we increment a reference count on the QP. The user releases the
reference by calling ib_release_qp. This releases any access to the QP
from a user above verbs, but allows the QP to continue to exist until
destroyed by the XRCD.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
XRC ("eXtended reliable connected") is an IB transport that provides
better scalability by allowing senders to specify which shared receive
queue (SRQ) should be used to receive a message, which essentially
allows one transport context (QP connection) to serve multiple
destinations (as long as they share an adapter, of course).
XRC communication is between an initiator (INI) QP and a target (TGT)
QP. Target QPs are associated with SRQs through an XRCD. An XRC TGT QP
behaves like a receive-only RD QP. XRC INI QPs behave similarly to RC
QPs, except that work requests posted to an XRC INI QP must specify the
remote SRQ that is the target of the work request.
We define two new QP types for XRC, to distinguish between INI and TGT
QPs, and update the core layer to support XRC QPs.
This patch is derived from work by Jack Morgenstein
<jackm@dev.mellanox.co.il>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
XRC ("eXtended reliable connected") is an IB transport that provides
better scalability by allowing senders to specify which shared receive
queue (SRQ) should be used to receive a message, which essentially
allows one transport context (QP connection) to serve multiple
destinations (as long as they share an adapter, of course).
XRC defines SRQs that are specifically used by XRC connections. Expand
the SRQ code to support XRC SRQs. An XRC SRQ is currently restricted to
only XRC use according to the IB XRC Annex.
Portions of this patch were derived from work by
Jack Morgenstein <jackm@dev.mellanox.co.il>.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Currently, there is only a single ("basic") type of SRQ, but with XRC
support we will add a second. Prepare for this by defining an SRQ type
and setting all current users to IB_SRQT_BASIC.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
XRC ("eXtended reliable connected") is an IB transport that provides
better scalability by allowing senders to specify which shared receive
queue (SRQ) should be used to receive a message, which essentially
allows one transport context (QP connection) to serve multiple
destinations (as long as they share an adapter, of course).
A few new concepts are introduced to support this. This patch adds:
- A new device capability flag, IB_DEVICE_XRC, which low-level
drivers set to indicate that a device supports XRC.
- A new object type, XRC domains (struct ib_xrcd), and new verbs
ib_alloc_xrcd()/ib_dealloc_xrcd(). XRCDs are used to limit which
XRC SRQs an incoming message can target.
This patch is derived from work by Jack Morgenstein <jackm@dev.mellanox.co.il>.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Use new function ib_rate_to_mbps() to handle printing rate in debugfs,
so that we handle extended rates.
Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Introduce support for the following extended speeds:
FDR-10: a Mellanox proprietary link speed which is 10.3125 Gbps with
64b/66b encoding rather than 8b/10b encoding.
FDR: IBA extended speed 14.0625 Gbps.
EDR: IBA extended speed 25.78125 Gbps.
Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix build errors:
drivers/infiniband/hw/ipath/ipath_init_chip.c:54:1: error: 'S_IRUGO' undeclared here (not in a function)
drivers/infiniband/hw/ipath/ipath_init_chip.c:54:1: error: bit-field '<anonymous>' width not an integer constant
drivers/infiniband/hw/ipath/ipath_init_chip.c:67:1: error: 'S_IWUSR' undeclared here (not in a function)
drivers/infiniband/hw/ipath/ipath_init_chip.c:67:1: error: bit-field '<anonymous>' width not an integer constant
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Support for Packed and Unaligned (PAU) FPDUs is needed for
interoperability between NES and non-NES nodes. When the NES hardware
detects a PAU frame, it will pass it to the driver to process the
frame. NES driver creates a new frame for each FPDU and forwards it
to the hardware to be sent to its associated qp.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Faisal Latif <Faisal.Latif@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Print the IP address of the remote host when a critical asynchronous event is
received.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Faisal Latif <Faisal.Latif@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fixes a crash that occurs during close when error async event is received.
Terminate message is not sent to the remote node if already processing close.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Faisal Latif <Faisal.Latif@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When I converted some drivers from pci_map_page to skb_frag_dma_map I
neglected to convert PCI_DMA_xDEVICE into DMA_x_DEVICE and
pci_dma_mapping_error into dma_mapping_error.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Enhanced RDMA Connection Establishment
(draft-ietf-storm-mpa-peer-connect-06), aka MPAv2. Details of draft
can be obtained from:
<http://www.ietf.org/id/draft-ietf-storm-mpa-peer-connect-06.txt>
For backwards compatibility, the MPAv2 enabled driver reverts to MPAv1
if the remote node doesn't support MPAv2.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Faisal Latif <Faisal.Latif@intel.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch adds support for Enhanced RDMA Connection Establishment
(draft-ietf-storm-mpa-peer-connect-06), aka MPAv2. Details of draft
can be obtained from:
<http://www.ietf.org/id/draft-ietf-storm-mpa-peer-connect-06.txt>
The patch updates the following functions for initiator perspective:
- send_mpa_request
- process_mpa_reply
- post_terminate for TERM error codes
- destroy_qp for TERM related change
- adds layer/etype/ecode to c4iw_qp_attrs for sending with TERM
- peer_abort for retrying connection attempt with MPA_v1 message
- added c4iw_reconnect function
The patch updates the following functions for responder perspective:
- process_mpa_request
- send_mpa_reply
- c4iw_accept_cr
- passes ird/ord to upper layers
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
As part of MPAv2 Enhanced RDMA Negotiation, pass max supported ird/ord
values upwards for the time being in iw_cxgb3 and amso1100.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Update struct iw_cm_event to support propagating the ird/ord values
upwards to the application.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The code that was recently introduced to report the number
of free contexts is flawed for multiple HCAs:
/* Return the number of free user ports (contexts) available. */
return scnprintf(buf, PAGE_SIZE, "%u\n", dd->cfgctxts -
dd->first_user_ctxt - (u32)qib_stats.sps_ctxts);
The qib_stats is global to the module, not per HCA, so the code is broken
for multiple HCAs.
This patch adds a qib_devdata field, freectxts, that reflects the free
contexts for this HCA.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Reviewed-by: Ram Vepa <ram.vepa@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add calls to ib_umem_release(), as in the other error-handling code in
nes_reg_user_mr().
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Roland Dreier <roland@purestorage.com>
cmd is unsigned, no need to check for < 0. Found by code inspection.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
If a received MAD contains an invalid or reserved mgmt class, we will
attempt to access method_table outside of its range. Add a check to
ensure that mgmt class falls within the handled range.
Found by code inspection.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Check that conn_param is not null before dereferencing it when
processing rdma_accept(). This is necessary to prevent a possible
system crash, which can be caused by user space.
Problem found by code inspection.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Since commit e58aa3d2d0 ("genirq: Run irq handlers with interrupts
disabled"), we run all interrupt handlers with interrupts disabled and
we even check and yell when an interrupt handler returns with
interrupts enabled -- cf commit b738a50a20 ("genirq: Warn when
handler enables interrupts").
So now this flag is a no-op and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The iw_cxgb4 module crashes at init time if the T4 card does not
support RDMA. So clean up the init logic to correctly deal with
non-RDMA cards.
- If any RDMA resources are not available, then fail the initialization
logging an info message.
- Clean up properly on initialization failures.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The RDMA CM uses the local qp_type to determine how to process an
incoming request. This can result in an incoming REQ being treated as
a SIDR REQ and vice versa. Fix this by switching off the event type
instead, and for good measure verify that the listener supports the
incoming connection request.
This problem showed up when a user space application mismatched the QP
types between a client and server app.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This oops was reported recently:
d:mon> e
cpu 0xd: Vector: 300 (Data Access) at [c0000000fd4c7120]
pc: d00000000076f194: .t3_l2t_get+0x44/0x524 [cxgb3]
lr: d000000000b02108: .init_act_open+0x150/0x3d4 [cxgb3i]
sp: c0000000fd4c73a0
msr: 8000000000009032
dar: 0
dsisr: 40000000
current = 0xc0000000fd640d40
paca = 0xc00000000054ff80
pid = 5085, comm = iscsid
d:mon> t
[c0000000fd4c7450] d000000000b02108 .init_act_open+0x150/0x3d4 [cxgb3i]
[c0000000fd4c7500] d000000000e45378 .cxgbi_ep_connect+0x784/0x8e8 [libcxgbi]
[c0000000fd4c7650] d000000000db33f0 .iscsi_if_rx+0x71c/0xb18
[scsi_transport_iscsi2]
[c0000000fd4c7740] c000000000370c9c .netlink_data_ready+0x40/0xa4
[c0000000fd4c77c0] c00000000036f010 .netlink_sendskb+0x4c/0x9c
[c0000000fd4c7850] c000000000370c18 .netlink_sendmsg+0x358/0x39c
[c0000000fd4c7950] c00000000033be24 .sock_sendmsg+0x114/0x1b8
[c0000000fd4c7b50] c00000000033d208 .sys_sendmsg+0x218/0x2ac
[c0000000fd4c7d70] c00000000033f55c .sys_socketcall+0x228/0x27c
[c0000000fd4c7e30] c0000000000086a4 syscall_exit+0x0/0x40
--- Exception: c01 (System Call) at 00000080da560cfc
The root cause was an EEH error, which sent us down the offload_close path in
the cxgb3 driver, which in turn sets cdev->l2opt to NULL, without regard for
upper layer driver (like the cxgbi drivers) which might have execution contexts
in the middle of its use. The result is the oops above, when t3_l2t_get attempts
to dereference L2DATA(cdev)->nentries in arp_hash right after the EEH error handler sets it to NULL.
The fix is to prevent the setting of the NULL pointer until after there are no
further users of it. The t3cdev->l2opt pointer is now converted to be an rcu
pointer and the L2DATA macro is now called under the protection of the
rcu_read_lock(). When the EEH error path:
t3_adapter_error->offload_close->cxgb3_offload_deactivate
Is exectured, setting of that l2opt pointer to NULL, is now gated on an rcu
quiescence point, preventing, allowing L2DATA callers to safely check for a NULL
pointer without concern that the underlying data will be freeded before the
pointer is dereferenced.
This has been tested by the reporter and shown to fix the reproted oops
[nhorman: fix up unitinialised variable reported by Dan Carpenter]
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Karen Xie <kxie@chelsio.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and driver's host attrs to use the attribute
container sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and driver's session attrs to use the attribute
container sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and drivers to use the attribute container
sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Roland Dreier <roland@kernel.org>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux-rdma@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Faisal Latif <faisal.latif@intel.com>
Cc: Roland Dreier <roland@kernel.org>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux-rdma@vger.kernel.org
Cc: netdev@vger.kernel.org
Acked-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tom Tucker <tom@opengridcomputing.com>
Cc: Steve Wise <swise@opengridcomputing.com>
Cc: Roland Dreier <roland@kernel.org>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux-rdma@vger.kernel.org
Cc: netdev@vger.kernel.org
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC3270 mandates that iSCSI PDUs are padded to the closest integer
number of four byte words. Fix the iser code to support that on both
the TX/RX flows.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The code that prepares the SG associated with SCSI command for FMR was
buggy for systems with DMA addresses that don't fit in unsigned long,
e.g under the 32-bit based XenServer dom0 sizeof(dma_addr_t) is 8.
Fix that by casting to unsigned long long a masking constant used by
the code. This resolves a crash in iser_sg_to_page_vec on this system.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Moves the drivers for the Chelsio chipsets into
drivers/net/ethernet/chelsio/ and the necessary Kconfig and Makefile
changes.
CC: Divy Le Ray <divy@chelsio.com>
CC: Dimitris Michailidis <dm@chelsio.com>
CC: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Convert to DIV_ROUND_UP_SECTOR_T usage for sectors / dev_max_sectors
kernel.h: Add DIV_ROUND_UP_ULL and DIV_ROUND_UP_SECTOR_T macro usage
iscsi-target: Add iSCSI fabric support for target v4.1
iscsi: Add Serial Number Arithmetic LT and GT into iscsi_proto.h
iscsi: Use struct scsi_lun in iscsi structs instead of u8[8]
iscsi: Resolve iscsi_proto.h naming conflicts with drivers/target/iscsi
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch renames the following iscsi_proto.h structures to avoid
namespace issues with drivers/target/iscsi/iscsi_target_core.h:
*) struct iscsi_cmd -> struct iscsi_scsi_req
*) struct iscsi_cmd_rsp -> struct iscsi_scsi_rsp
*) struct iscsi_login -> struct iscsi_login_req
This patch includes useful ISCSI_FLAG_LOGIN_[CURRENT,NEXT]_STAGE*,
and ISCSI_FLAG_SNACK_TYPE_* definitions used by iscsi_target_mod, and
fixes the incorrect definition of struct iscsi_snack to following
RFC-3720 Section 10.16. SNACK Request.
Also, this patch updates libiscsi, iSER, be2iscsi, and bn2xi to
use the updated structure definitions in a handful of locations.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (26 commits)
IB/qib: Defer HCA error events to tasklet
mlx4_core: Bump the driver version to 1.0
RDMA/cxgb4: Use printk_ratelimited() instead of printk_ratelimit()
IB/mlx4: Support PMA counters for IBoE
IB/mlx4: Use flow counters on IBoE ports
IB/pma: Add include file for IBA performance counters definitions
mlx4_core: Add network flow counters
mlx4_core: Fix location of counter index in QP context struct
mlx4_core: Read extended capabilities into the flags field
mlx4_core: Extend capability flags to 64 bits
IB/mlx4: Generate GID change events in IBoE code
IB/core: Add GID change event
RDMA/cma: Don't allow IPoIB port space for IBoE
RDMA: Allow for NULL .modify_device() and .modify_port() methods
IB/qib: Update active link width
IB/qib: Fix potential deadlock with link down interrupt
IB/qib: Add sysfs interface to read free contexts
IB/mthca: Remove unnecessary read of PCI_CAP_ID_EXP
IB/qib: Remove double define
IB/qib: Remove unnecessary read of PCI_CAP_ID_EXP
...
With ib_qib options:
options ib_qib krcvqs=1 pcie_caps=0x51 rcvhdrcnt=4096 singleport=1 ibmtu=4
a run of ib_write_bw -a yields the following:
------------------------------------------------------------------
#bytes #iterations BW peak[MB/sec] BW average[MB/sec]
1048576 5000 2910.64 229.80
------------------------------------------------------------------
The top cpu use in a profile is:
CPU: Intel Architectural Perfmon, speed 2400.15 MHz (estimated)
Counted CPU_CLK_UNHALTED events (Clock cycles when not halted) with a unit mask
of 0x00 (No unit mask) count 1002300
Counted LLC_MISSES events (Last level cache demand requests from this core that
missed the LLC) with a unit mask of 0x41 (No unit mask) count 10000
samples % samples % app name symbol name
15237 29.2642 964 17.1195 ib_qib.ko qib_7322intr
12320 23.6618 1040 18.4692 ib_qib.ko handle_7322_errors
4106 7.8860 0 0 vmlinux vsnprintf
Analysis of the stats, profile, the code, and the annotated profile indicate:
- All of the overflow interrupts (one per packet overflow) are
serviced on CPU0 with no mitigation on the frequency.
- All of the receive interrupts are being serviced by CPU0. (That is
the way truescale.cmds statically allocates the kctx IRQs to CPU)
- The code is spending all of its time servicing QIB_I_C_ERROR
RcvEgrFullErr interrupts on CPU0, starving the packet receive
processing.
- The decode_err routine is very inefficient, using a printf variant
to format a "%s" and continues to loop when the errs mask has been
cleared.
- Both qib_7322intr and handle_7322_errors read pci registers, which
is very inefficient.
The fix does the following:
- Adds a tasklet to service QIB_I_C_ERROR
- Replaces the very inefficient scnprintf() with a memcpy(). A field
is added to qib_hwerror_msgs to save the sizeof("string") at
compile time so that a strlen is not needed during err_decode().
- The most frequent errors (Overflows) are serviced first to exit the
loop as early as possible.
- The loop now exits as soon as the errs mask is clear rather than
fruitlessly looping through the msp array.
With this fix the performance changes to:
------------------------------------------------------------------
#bytes #iterations BW peak[MB/sec] BW average[MB/sec]
1048576 5000 2990.64 2941.35
------------------------------------------------------------------
During testing of the error handling overflow patch, it was determined
that some CPU's were slower when servicing both overflow and receive
interrupts on CPU0 with different MSI interrupt vectors.
This patch adds an option (krcvq01_no_msi) to not use a dedicated MSI
interrupt for kctx's < 2 and to service them on the default interrupt.
For some CPUs, the cost of the interrupt enter/exit is more costly
than then the additional PCI read in the default handler.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
- unify vlan and nonvlan rx path
- kill nesvnic->vlan_grp and nes_netdev_vlan_rx_register
- allow to turn on/off rx/tx vlan accel via ethtool (set_features)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since printk_ratelimit() shouldn't be used anymore (see comment in
include/linux/printk.h), replace it with printk_ratelimited().
Signed-off-by: Manuel Zerpies <manuel.f.zerpies@ww.stud.uni-erlangen.de>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Use the per port counter attached to all QPs created on that port to
implement port level packets/bytes performance counters a la IB.
Derived from a patch by Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Allocate flow counter per Ethernet/IBoE port, and attach this counter
to all the QPs created on that port. Based on patch by Eli Cohen
<eli@mellanox.co.il>.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Move the various definitions and mad structures needed for software
implementation of IBA PM agent from the ipath and qib drivers into a
single include file, which in turn could be used by more consumers.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
IBoE doesn't use LIDs. Use the GID change event to update the IB core
cache for addition/deletion of GIDs.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add IB GID change event type. This is needed for IBoE when the HW
driver updates the GID (e.g when new VLANs are added/deleted) table
and the change should be reflected to the IB core cache.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch fixes a kernel crash in cma_set_qkey().
When the link layer is Ethernet, it is wrong to use IPoIB port space
since no IPoIB interface is available. Specifically, setting the
Q_Key when port space is RDMA_PS_IPOIB requires MGID calculation and
an SA query, which doesn't make sense over Ethernet.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
These methods don't make sense for iWARP devices, so rather than
forcing them to implement stubs, just return -ENOSYS in the core if
the hardware driver doesn't set .modify_device and/or .modify_port.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Update the active link width on QLE7220 chips when link goes down if
chip width does not match shadowed width.
Signed-off-by: Mitko Haralanov <mitko@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There is a possibility of a deadlock due to the way locks are
acquired and released in qib_set_uevent_bits(). The function
qib_set_uevent_bits() is called in process context and it uses
spin_lock() and spin_unlock(). This same lock is acquired/released
in interrupt context which can lead to a deadlock when running on
the same cpu.
The fix is to replace spin_lock() and spin_unlock() with
spin_lock_irqsave() and spin_unlock_irqrestore() respectively in
qib_set_uevent_bits().
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Indicate the number of free user contexts via the sysfs file
/sys/class/infiniband/qib0/nfreectxts as required for PSM.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The PCIE capability offset is saved during PCI bus walking. It will
remove an unnecessary search in the PCI configuration space if this
value is referenced instead of reacquiring it. Also, pci_is_pcie is a
better way of determining if the device is PCIE or not (as it uses the
same saved PCIE capability offset).
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The PCIE capability offset is saved during PCI bus walking. It will
remove an unnecessary search in the PCI configuration space if this
value is referenced instead of reacquiring it.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Acked-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Adapt to new api. We plan to remove old one later. Almost all
changes are trivial, but there is one real fix: the following code is
unsafe:
int ncpus = num_online_cpus()
for (i = 0; i < ncpus; i++) {
..
}
because 1) we don't guarantee last bit of online cpus is equal to
num_online_cpus(). some arch assign sparse cpu number. 2) cpu
hotplugging may change cpu_online_mask at same time. we need to pin
it by get_online_cpus().
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Adapt to use new APIs. We plan to remove old one later and plan to
change current->cpus_allowed implementation.
No functional change.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Avoid assigning an IS_ERR value to the cm_id pointer. This fixes a
few anomalies in the error flow due to confusion about checking for
NULL vs IS_ERR, and eliminates the need to test for the IS_ERR value
every time we wish to determine if the cma_id object has a cm device
associated with it.
Also, eliminate the now-unnecessary procedure cma_has_cm_dev (we can
check directly for the existence of the device pointer -- for a
non-NULL check, makes no difference if it is the iwarp or the ib
pointer).
Finally, make a few code changes here to improve coding consistency.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
SCSI scanning of a channel🆔lun triplet in Linux works as follows
(function scsi_scan_target() in drivers/scsi/scsi_scan.c):
- If lun == SCAN_WILD_CARD, send a REPORT LUNS command to the target
and process the result.
- If lun != SCAN_WILD_CARD, send an INQUIRY command to the LUN
corresponding to the specified channel🆔lun triplet to verify
whether the LUN exists.
So a SCSI driver must either take the channel and target id values in
account in its quecommand() function or it should declare that it only
supports one channel and one target id.
Currently the ib_srp driver does neither. As a result scanning the
SCSI bus via e.g. rescan-scsi-bus.sh causes many duplicate SCSI
devices to be created. For each 0:0:L device, several duplicates are
created with the same LUN number and with (C:I) != (0:0). Fix this by
declaring that the ib_srp driver only supports one channel and one
target id.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: <stable@kernel.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commits 71c29bd5c2 ("IB/uverbs: Add devnode method to set path/mode")
and c3af0980ce ("IB: Add devnode methods to cm_class and umad_class")
added devnode methods that set the mode.
However, these methods don't check for a NULL mode, and so we get a
crash when unloading modules because devtmpfs_delete_node() calls
device_get_devnode() with mode == NULL.
Add the missing checks.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.de>
[ Also fix cm.c. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Due to timing, it is possible for the LOS and DFE to remain on. This
is due to the link progressing to LinkUP prior to the driver getting
the first Status Changed interrupt. By expanding the conditions under
which LOS is turned off and DFE timeout is being set, timing is no
longer an issue.
Signed-off-by: Mitko Haralanov <mitko@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
- fix a race where the driver could end up sending a close_con_req
after an abort_rpl. In c4iw_ep_disconnect(), send abort or close
request with the ep mutex held.
- fix a hang where driver fails to wake up when a connection is reset
during a normal close. Wake up any waiters in the interrupt path,
and correctly cleanup after rdma_fini() failures.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Remove left-over code from T3 that limited MR sizes to 32b.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Memory allocated for user CQs gets rounded up to the next page
boundary. And after rounding, we recalculate the resulting IQ depth
and we need to make sure we don't exceed the HW limits.
This bug can result a much smaller CQ allocated than was expected if
the HW size field is exceeded, resulting in CQ overflow failures.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The message size allocated for rtnl ifinfo dumps was limited to
a single page. This is not enough for additional interface info
available with devices that support SR-IOV and caused a bug in
which VF info would not be displayed if more than approximately
40 VFs were created per interface.
Implement a new function pointer for the rtnl_register service that will
calculate the amount of data required for the ifinfo dump and allocate
enough data to satisfy the request.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* remove interrupt.g inclusion from netdevice.h -- not needed
* fixup fallout, add interrupt.h and hardirq.h back where needed.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/cma: Save PID of ID's owner
RDMA/cma: Add support for netlink statistics export
RDMA/cma: Pass QP type into rdma_create_id()
RDMA: Update exported headers list
RDMA/cma: Export enum cma_state in <rdma/rdma_cm.h>
RDMA/nes: Add a check for strict_strtoul()
RDMA/cxgb3: Don't post zero-byte read if endpoint is going away
RDMA/cxgb4: Use completion objects for event blocking
IB/srp: Fix integer -> pointer cast warnings
IB: Add devnode methods to cm_class and umad_class
IB/mad: Return EPROTONOSUPPORT when an RDMA device lacks the QP required
IB/uverbs: Add devnode method to set path/mode
RDMA/ucma: Add .nodename/.mode to tell userspace where to create device node
RDMA: Add netlink infrastructure
RDMA: Add error handling to ib_core_init()
Save the PID associated with an RDMA CM ID for reporting via netlink.
Signed-off-by: Nir Muchtar <nirm@voltaire.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add callbacks and data types for statistics export of all current
devices/ids. The schema for RDMA CM is a series of netlink messages.
Each one contains an rdma_cm_stat struct. Additionally, two netlink
attributes are created for the addresses for each message (if
applicable).
Their types used are:
RDMA_NL_RDMA_CM_ATTR_SRC_ADDR (The source address for this ID)
RDMA_NL_RDMA_CM_ATTR_DST_ADDR (The destination address for this ID)
sockaddr_* structs are encapsulated within these attributes.
In other words, every transaction contains a series of messages like:
-------message 1-------
struct rdma_cm_id_stats {
__u32 qp_num;
__u32 bound_dev_if;
__u32 port_space;
__s32 pid;
__u8 cm_state;
__u8 node_type;
__u8 port_num;
__u8 reserved;
}
RDMA_NL_RDMA_CM_ATTR_SRC_ADDR attribute - contains the source address
RDMA_NL_RDMA_CM_ATTR_DST_ADDR attribute - contains the destination address
-------end 1-------
-------message 2-------
struct rdma_cm_id_stats
RDMA_NL_RDMA_CM_ATTR_SRC_ADDR attribute
RDMA_NL_RDMA_CM_ATTR_DST_ADDR attribute
-------end 2-------
Signed-off-by: Nir Muchtar <nirm@voltaire.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The RDMA CM currently infers the QP type from the port space selected
by the user. In the future (eg with RDMA_PS_IB or XRC), there may not
be a 1-1 correspondence between port space and QP type. For netlink
export of RDMA CM state, we want to export the QP type to userspace,
so it is cleaner to explicitly associate a QP type to an ID.
Modify rdma_create_id() to allow the user to specify the QP type, and
use it to make our selections of datagram versus connected mode.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Move cma.c's internal definition of enum cma_state to enum rdma_cm_state
in an exported header so that it can be exported via RDMA netlink.
Signed-off-by: Nir Muchtar <nirm@voltaire.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
It should check if strict_strtoul() succeeds before using
'wqm_quanta_value'.
Signed-off-by: Liu Yuan <tailai.ly@taobao.com>
[ Convert to kstrtoul() directly while we're here. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
tx_ack() wasn't checking the endpoint state and consequently would
attempt to post the p2p 0B read on an endpoint/QP that is closing or
aborting. This causes a NULL pointer dereference crash.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There exists a race condition when using wait_queue_head_t objects
that are declared on the stack. This was being done in a few places
where we are sending work requests to the FW and awaiting replies, but
we don't have an endpoint structure with an embedded c4iw_wr_wait
struct. So the code was allocating it locally on the stack. Bad
design. The race is:
1) thread on cpuX declares the wait_queue_head_t on the stack, then
posts a firmware WR with that wait object ptr as the cookie to be
returned in the WR reply. This thread will proceed to block in
wait_event_timeout() but before it does:
2) An interrupt runs on cpuY with the WR reply. fw6_msg() handles
this and calls c4iw_wake_up(). c4iw_wake_up() sets the condition
variable in the c4iw_wr_wait object to TRUE and will call
wake_up(), but before it calls wake_up():
3) The thread on cpuX calls c4iw_wait_for_reply(), which calls
wait_event_timeout(). The wait_event_timeout() macro checks the
condition variable and returns immediately since it is TRUE. So
this thread never blocks/sleeps. The function then returns
effectively deallocating the c4iw_wr_wait object that was on the
stack.
4) So at this point cpuY has a pointer to the c4iw_wr_wait object
that is no longer valid. Further its pointing to a stack frame
that might now be in use by some other context/thread. So cpuY
continues execution and calls wake_up() on a ptr to a wait object
that as been effectively deallocated.
This race, when it hits, can cause a crash in wake_up(), which I've
seen under heavy stress. It can also corrupt the referenced stack
which can cause any number of failures.
The fix:
Use struct completion, which supports on-stack declarations.
Completions use a spinlock around setting the condition to true and
the wake up so that steps 2 and 4 above are atomic and step 3 can
never happen in-between.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Fix
drivers/infiniband/ulp/srp/ib_srp.c: In function 'srp_handle_recv':
drivers/infiniband/ulp/srp/ib_srp.c:1150: warning: cast to pointer from integer of different size
drivers/infiniband/ulp/srp/ib_srp.c: In function 'srp_send_completion':
drivers/infiniband/ulp/srp/ib_srp.c🔢 warning: cast to pointer from integer of different size
by adding an intermediate cast to uintptr_t.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Acked-by: David Dillow <dillowda@ornl.gov>
We want the ucmX, umadX and issmX device nodes to show up under
/dev/infiniband, and additionally ucmX should have mode 0666. Add
appropriate devnode methods to their class structs for this.
Signed-off-by: Roland Dreier <roland@purestorage.com>
We had a script which was looping through the devices returned from
ibstat and attempted to register a SMI agent on an ethernet device.
This caused a kernel panic for IBoE devices that don't have QP0.
Fix this by checking if the QP exists before using it.
Signed-off-by: Ira Weiny <weiny2@llnl.gov>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We want udev to create a device node under /dev/infiniband with
permission 0666 for uverbsX devices, so add a devnode method to set the
appropriate info.
Signed-off-by: Roland Dreier <roland@purestorage.com>
We want udev to create a device node under /dev/infiniband with
permission 0666 for rdma_cm, so add that info to our struct miscdevice.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
After discovering that wide use of prefetch on modern CPUs
could be a net loss instead of a win, net drivers which were
relying on the implicit inclusion of prefetch.h via the list
headers showed up in the resulting cleanup fallout. Give
them an explicit include via the following $0.02 script.
=========================================
#!/bin/bash
MANUAL=""
for i in `git grep -l 'prefetch(.*)' .` ; do
grep -q '<linux/prefetch.h>' $i
if [ $? = 0 ] ; then
continue
fi
( echo '?^#include <linux/?a'
echo '#include <linux/prefetch.h>'
echo .
echo w
echo q
) | ed -s $i > /dev/null 2>&1
if [ $? != 0 ]; then
echo $i needs manual fixup
MANUAL="$i $MANUAL"
fi
done
echo ------------------- 8\<----------------------
echo vi $MANUAL
=========================================
Signed-off-by: Paul <paul.gortmaker@windriver.com>
[ Fixed up some incorrect #include placements, and added some
non-network drivers and the fib_trie.c case - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1446 commits)
macvlan: fix panic if lowerdev in a bond
tg3: Add braces around 5906 workaround.
tg3: Fix NETIF_F_LOOPBACK error
macvlan: remove one synchronize_rcu() call
networking: NET_CLS_ROUTE4 depends on INET
irda: Fix error propagation in ircomm_lmp_connect_response()
irda: Kill set but unused variable 'bytes' in irlan_check_command_param()
irda: Kill set but unused variable 'clen' in ircomm_connect_indication()
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_transport()
be2net: Kill set but unused variable 'req' in lancer_fw_download()
irda: Kill set but unused vars 'saddr' and 'daddr' in irlan_provider_connect_indication()
atl1c: atl1c_resume() is only used when CONFIG_PM_SLEEP is defined.
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_peer().
rxrpc: Kill set but unused variable 'local' in rxrpc_UDP_error_handler()
rxrpc: Kill set but unused variable 'sp' in rxrpc_process_connection()
rxrpc: Kill set but unused variable 'sp' in rxrpc_rotate_tx_window()
pkt_sched: Kill set but unused variable 'protocol' in tc_classify()
isdn: capi: Use pr_debug() instead of ifdefs.
tg3: Update version to 3.119
tg3: Apply rx_discards fix to 5719/5720
...
Fix up trivial conflicts in arch/x86/Kconfig and net/mac80211/agg-tx.c
as per Davem.
Add basic RDMA netlink infrastructure that allows for registration of
RDMA clients for which data is to be exported and supplies message
construction callbacks.
Signed-off-by: Nir Muchtar <nirm@voltaire.com>
[ Reorganize a few things, add CONFIG_NET dependency. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Manual merge of arch/powerpc/kernel/smp.c and add missing scheduler_ipi()
call to arch/powerpc/platforms/cell/interrupt.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The driver reads PCI revision ID from the PCI configuration register
while it's already stored by PCI subsystem in the revision field of
struct pci_dev.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The IW_CM_EVENT_STATUS_xxx values were used in only a couple of places;
cma.c uses -Exxx values instead, and so do the amso1100, cxgb3 and cxgb4
drivers -- only nes was using the enum values (with the mild consequence
that all nes connection failures were treated as generic errors rather
than reported as timeouts or rejections).
We can fix this confusion by getting rid of enum iw_cm_event_status and
using a plain int for struct iw_cm_event.status, and converting nes to
use -Exxx as the other iWARP drivers do.
This also gets rid of the warning
drivers/infiniband/core/cma.c: In function 'cma_iw_handler':
drivers/infiniband/core/cma.c:1333:3: warning: case value '4294967185' not in enumerated type 'enum iw_cm_event_status'
drivers/infiniband/core/cma.c:1336:3: warning: case value '4294967186' not in enumerated type 'enum iw_cm_event_status'
drivers/infiniband/core/cma.c:1332:3: warning: case value '4294967192' not in enumerated type 'enum iw_cm_event_status'
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Faisal Latif <faisal.latif@intel.com>
Commit 44c10138fd ("PCI: Change all drivers to use pci_device->revision")
already converted this driver to using the revision field of struct
pci_dev but commit bb9171448d ("IB/ipath: Misc changes to prepare
for IB7220 introduction") later reverted that change for some strange
reason. Restore the change.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The time limit test now correctly checks against current jiffies to
avoid the hang.
Signed-off-by: Mitko Haralanov <mitko@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
A few more EEH fixes:
c4iw_wait_for_reply(): detect fatal EEH condition on timeout and
return an error.
The iw_cxgb4 driver was only calling ib_deregister_device() on an EEH
event followed by a ib_register_device() when the device was
reinitialized. However, the RDMA core doesn't allow multiple
iterations of register/deregister by the provider. See
drivers/infiniband/core/sysfs.c: ib_device_unregister_sysfs() where
the kobject ref is held until the device is deallocated in
ib_deallocate_device(). Calling deregister adds this kobj reference,
and then a subsequent register call will generate a WARN_ON() from the
kobject subsystem because the kobject is being initialized but is
already initialized with the ref held.
So the provider must deregister and dealloc when resetting for an EEH
event, then alloc/register to re-initialize. To do this, we cannot
use the device ptr as our ULD handle since it will change with each
reallocation. This commit adds a ULD context struct which is used as
the ULD handle, and then contains the device pointer and other state
needed.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The driver was never really waiting for RDMA_WR/FINI completions
because the condition variable used to determine if the completion
happened was never reset, and this condition variable is reused for
both connection setup and teardown. This causes various driver
crashes under heavy loads due to releasing resources too early.
The fix is to use atomic bits to correctly reset the condition
immediately after the completion is detected.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Parens are missing: '|' has a higher presedence than '?'.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
c4iw_uld_add() must return ERR_PTR() values instead of NULL on failure.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Concurrent ingress CLOSE and ULP ABORT operations causes a crash due
to a race condition where the close path releases the EP lock and then
tries to move the QP state to CLOSED. This must be done inside the EP
lock to avoid the race.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Lustre requires that clients bind to a privileged port number before
connecting to a remote server. On larger clusters (typically more
than about 1000 nodes), the number of privileged ports is exhausted,
resulting in lustre being unusable.
To handle this, we add support for reusable addresses to the rdma_cm.
This mimics the behavior of the socket option SO_REUSEADDR. A user
may set an rdma_cm_id to reuse an address before calling
rdma_bind_addr() (explicitly or implicitly). If set, other
rdma_cm_id's may be bound to the same address, provided that they all
have reuse enabled, and there are no active listens.
If rdma_listen() is called on an rdma_cm_id that has reuse enabled, it
will only succeed if there are no other id's bound to that same
address. The reuse option is exported to user space. The behavior of
the kernel reuse implementation was verified against that given by
sockets.
This patch is derived from a path by Ira Weiny <weiny2@llnl.gov>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
cma_use_port() assumes that the sockaddr is an IPv4 address. Since
IPv6 addressing is supported (and also to support other address
families) make the code more generic in its address handling.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This updates the network drivers so that they don't access the
ethtool_cmd::speed field directly, but use ethtool_cmd_speed()
instead.
For most of the drivers, these changes are purely cosmetic and don't
fix any problem, such as for those 1GbE/10GbE drivers that indirectly
call their own ethtool get_settings()/mii_ethtool_gset(). The changes
are meant to enforce code consistency and provide robustness with
future larger throughputs, at the expense of a few CPU cycles for each
ethtool operation.
All drivers compiled with make allyesconfig ion x86_64 have been
updated.
Tested: make allyesconfig on x86_64 + e1000e/bnx2x work
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
