Since the ARM AMBA bus is used on MIPS as well as ARM, we need
to make the bus available for other architectures to use. Move
the AMBA include files from include/asm-arm/hardware/ to
include/linux/amba/
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Before this patch we were just using the "classic" /dev/ttySx devices.
However when another on the system is loaded that uses those (like drivers for
serial PCMCIA), that creates a conflict for the minors. Therefore, we now use
/dev/ttyPSC[0:5] (note the 0-based numbering !) with some minors we've been
assigned in the "Low Density Serial port major"
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Unify the EVENT_CARD_INSERTION and "attach" callbacks to one unified
probe() callback. As all in-kernel drivers are changed to this new
callback, there will be no temporary backwards-compatibility. Inside a
probe() function, each driver _must_ set struct pcmcia_device
*p_dev->instance and instance->handle correctly.
With these patches, the basic driver interface for 16-bit PCMCIA drivers
now has the classic four callbacks known also from other buses:
int (*probe) (struct pcmcia_device *dev);
void (*remove) (struct pcmcia_device *dev);
int (*suspend) (struct pcmcia_device *dev);
int (*resume) (struct pcmcia_device *dev);
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The linked list of devices managed by each PCMCIA driver is, in very most
cases, unused. Therefore, remove it from many drivers.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Unify the "detach" and REMOVAL_EVENT handlers to one "remove" function.
Old functionality is preserved, for the moment.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Move the suspend and resume methods out of the event handler, and into
special functions. Also use these functions for pre- and post-reset, as
almost all drivers already do, and the remaining ones can easily be
converted.
Bugfix to include/pcmcia/ds.c
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
All call sites for serial8250_handle_port() acquired the port spinlock
and released it afterwards. This is a needless duplication of code.
Move the spinlocking inside serial8250_handle_port().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The function uart_match_port() incorrectly compares the ioremap'd
virtual addresses of ports instead of the physical address to find
duplicate ports for MMIO based UARTs. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I've also fixed the sort-ordering comments on this naming convention.
Signed-off-by: Stuart MacDonald <stuartm@connecttech.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reading the MSR register on 8250-compatible UARTs results in any
modem status interrupts being cleared. To avoid missing any
status changes, arrange for get_mctrl() to read the current
status via check_modem_status(), which will process any pending
state changes for us.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It seems that clk_use() and clk_unuse() are additional complexity
which isn't required anymore. Remove them from the clock framework
to avoid the additional confusion which they cause, and update all
ARM machine types except for OMAP.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Erik Hovland
This patch provides two changes. An indent is supplied for an if/else clause so that it is more readable. An acronym is incorrectly typed as UER when it should be IER.
Signed-off-by: Erik Hovland <erik@hovland.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Introduce a Kconfig symbol SPARC that is defined on both the sparc and
sparc64 architectures.
This symbol makes some dependencies more readable.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch marks a few serial data structures const, moving them to
.rodata where they won't false-share cachelines with things that get
written to.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the spinlock was removed from sa1100_start_tx(), the "flags"
variable becomes redundant. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The receiver status register reports latched error conditions, which
must be cleared by writing to it. However, the data register reports
unlatched conditions which are associated with the current character.
Use the data register to interpret error status rather than the RSR.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Depend on GSC, not PARISC. Machines without GSC don't have a MUX.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This commit is in response to a bug reported by Vesa on the irc channel
a couple of weeks ago.
The bug was that the console would apparently hang (not return) while
using the mux console.
The root cause of this bug is that bash (with readline support) makes a
call to the tcsetattr() glibc function with the argument TCSADRAIN. This
causes the serial core in the kernel use the uart_wait_until_sent() to be
called. This function verifies the mux transmit queue is empty or calls the
msleep_interruptable() with a calculated timeout value that is dependant
upon the port->timeout variable.
The real problem here is that the port->timeout was not defined so it
was defaulted to 0 and the timeout calculation performs the following
calculation:
char_time = (port->timeout - HZ/50) / port->fifosize;
where char_time is an unsigned long. Since the serial Mux does not use
interrupts, the msleep_interruptable() function waits until the timeout
has been reached ... and when the port->timeout < HZ/50 this timeout will
be a long time. (I have validated that the console will eventually
return ... but it takes quite a while for this to happen).
This patch simply sets the port->timeout on the Mux to HZ/50 to avoid
this long timeout period.
Signed-off-by: Ryan Bradetich <rbrad@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This patch does the following:
* Fixes compiler warnings.
* Replaces a __raw_readl call with the existing macro.
Signed-off-by: Ryan Bradetich <rbrad@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Changed jobs and the Freescale address is no longer valid.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since few people need the support anymore, this moves the legacy
pm_xxx functions to CONFIG_PM_LEGACY, and include/linux/pm_legacy.h.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we fail to re-startup a serial port on resume, shut it down
immediately and mark it as an error condition.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Claim the WACF005 device. This is the pen display pointing device on
the HP Compaq tc1100 Tablet PC. More information about using this
device, including using it as an X pointer device:
http://www.theory.bham.ac.uk/staff/schofield/linux/tc1100/
Christopher Kemp <ck231@cam.ac.uk> did the legwork of determining that
the WACF005 is really just a plain old UART and doing an initial ACPI
driver (before we had PNPACPI), and David Ludlow <dave@adsllc.com>
confirmed that PNPACPI + the attached patch is now sufficient:
pnp: Device 00:05 activated.
ttyS4 at I/O 0x300 (irq = 4) is a 16550A
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix copy-paste bug in mpc52xx_uart.c (pdev<->dev)
Signed-off-by: Andrey Volkov <avolkov@varma-el.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use physical addresses at the interface level, letting drivers remap
them as appropriate.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
xscale-type UARTs have an extra bit (UUE) in the IER register that has
to be written as 1 to enable the UART. At the end of autoconfig() in
drivers/serial/8250.c, the IER register is unconditionally written as
zero, which turns off the UART, and makes any subsequent printch() hang
the box.
Since other 8250-type UARTs don't have this enable bit and are thus
always 'enabled' in this sense, it can't hurt to enable xscale-type
serial ports all the time as well. The attached patch changes the
autoconfig() exit path to see if the port has an UUE enable bit, and if
yes, to write UUE=1 instead of just putting a zero into IER, using the
same test as is used at the beginning of serial8250_console_write().
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows us to eliminate the casts in the drivers, and eventually
remove the use of the device_driver function pointer methods for
platform device drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the Freescale 5208 processor UART's to the common
ColdFire serial port code.
Patch originally from Matt Waddel (from code originally written by
Mike Lavender).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use schedule_timeout_uninterruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Large console spews from IRQ or local_irq_disable() sections can cause the NMI
watchdog to go off.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The offsets of the registers are in a different place, and
some parts cannot handle a full set of modem control signals.
Signed-off-by: Pantelis Antoniou <pantelis@embeddedalley.ocm>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix sparse warning about passing `0` to simple_strtoul()
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
