It appears that driver runs into a problem here if fibsize is too small
because we allocate user_srbcmd with fibsize size only but later we
access it until user_srbcmd->sg.count to copy it over to srbcmd.
It is not correct to test (fibsize < sizeof(*user_srbcmd)) because this
structure already includes one sg element and this is not needed for
commands without data. So, we would recommend to add the following
(instead of test for fibsize == 0).
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
"Mostly these are fixes for fallout due to merge window changes, as
well as cures for problems that have been with us for a much longer
period of time"
1) Johannes Berg noticed two major deficiencies in our genetlink
registration. Some genetlink protocols we passing in constant
counts for their ops array rather than something like
ARRAY_SIZE(ops) or similar. Also, some genetlink protocols were
using fixed IDs for their multicast groups.
We have to retain these fixed IDs to keep existing userland tools
working, but reserve them so that other multicast groups used by
other protocols can not possibly conflict.
In dealing with these two problems, we actually now use less state
management for genetlink operations and multicast groups.
2) When configuring interface hardware timestamping, fix several
drivers that simply do not validate that the hwtstamp_config value
is one the driver actually supports. From Ben Hutchings.
3) Invalid memory references in mwifiex driver, from Amitkumar Karwar.
4) In dev_forward_skb(), set the skb->protocol in the right order
relative to skb_scrub_packet(). From Alexei Starovoitov.
5) Bridge erroneously fails to use the proper wrapper functions to make
calls to netdev_ops->ndo_vlan_rx_{add,kill}_vid. Fix from Toshiaki
Makita.
6) When detaching a bridge port, make sure to flush all VLAN IDs to
prevent them from leaking, also from Toshiaki Makita.
7) Put in a compromise for TCP Small Queues so that deep queued devices
that delay TX reclaim non-trivially don't have such a performance
decrease. One particularly problematic area is 802.11 AMPDU in
wireless. From Eric Dumazet.
8) Fix crashes in tcp_fastopen_cache_get(), we can see NULL socket dsts
here. Fix from Eric Dumzaet, reported by Dave Jones.
9) Fix use after free in ipv6 SIT driver, from Willem de Bruijn.
10) When computing mergeable buffer sizes, virtio-net fails to take the
virtio-net header into account. From Michael Dalton.
11) Fix seqlock deadlock in ip4_datagram_connect() wrt. statistic
bumping, this one has been with us for a while. From Eric Dumazet.
12) Fix NULL deref in the new TIPC fragmentation handling, from Erik
Hugne.
13) 6lowpan bit used for traffic classification was wrong, from Jukka
Rissanen.
14) macvlan has the same issue as normal vlans did wrt. propagating LRO
disabling down to the real device, fix it the same way. From Michal
Kubecek.
15) CPSW driver needs to soft reset all slaves during suspend, from
Daniel Mack.
16) Fix small frame pacing in FQ packet scheduler, from Eric Dumazet.
17) The xen-netfront RX buffer refill timer isn't properly scheduled on
partial RX allocation success, from Ma JieYue.
18) When ipv6 ping protocol support was added, the AF_INET6 protocol
initialization cleanup path on failure was borked a little. Fix
from Vlad Yasevich.
19) If a socket disconnects during a read/recvmsg/recvfrom/etc that
blocks we can do the wrong thing with the msg_name we write back to
userspace. From Hannes Frederic Sowa. There is another fix in the
works from Hannes which will prevent future problems of this nature.
20) Fix route leak in VTI tunnel transmit, from Fan Du.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (106 commits)
genetlink: make multicast groups const, prevent abuse
genetlink: pass family to functions using groups
genetlink: add and use genl_set_err()
genetlink: remove family pointer from genl_multicast_group
genetlink: remove genl_unregister_mc_group()
hsr: don't call genl_unregister_mc_group()
quota/genetlink: use proper genetlink multicast APIs
drop_monitor/genetlink: use proper genetlink multicast APIs
genetlink: only pass array to genl_register_family_with_ops()
tcp: don't update snd_nxt, when a socket is switched from repair mode
atm: idt77252: fix dev refcnt leak
xfrm: Release dst if this dst is improper for vti tunnel
netlink: fix documentation typo in netlink_set_err()
be2net: Delete secondary unicast MAC addresses during be_close
be2net: Fix unconditional enabling of Rx interface options
net, virtio_net: replace the magic value
ping: prevent NULL pointer dereference on write to msg_name
bnx2x: Prevent "timeout waiting for state X"
bnx2x: prevent CFC attention
bnx2x: Prevent panic during DMAE timeout
...
This doesn't really change anything, but prepares for the
next patch that will change the APIs to pass the group ID
within the family, rather than the global group ID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Re-enable flow steering verbs with new improved userspace ABI
- Fixes for slow connection due to GID lookup scalability
- IPoIB fixes
- Many fixes to HW drivers including mlx4, mlx5, ocrdma and qib
- Further improvements to SRP error handling
- Add new transport type for Cisco usNIC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=xxC+
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma updates from Roland Dreier:
- Re-enable flow steering verbs with new improved userspace ABI
- Fixes for slow connection due to GID lookup scalability
- IPoIB fixes
- Many fixes to HW drivers including mlx4, mlx5, ocrdma and qib
- Further improvements to SRP error handling
- Add new transport type for Cisco usNIC
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (66 commits)
IB/core: Re-enable create_flow/destroy_flow uverbs
IB/core: extended command: an improved infrastructure for uverbs commands
IB/core: Remove ib_uverbs_flow_spec structure from userspace
IB/core: Use a common header for uverbs flow_specs
IB/core: Make uverbs flow structure use names like verbs ones
IB/core: Rename 'flow' structs to match other uverbs structs
IB/core: clarify overflow/underflow checks on ib_create/destroy_flow
IB/ucma: Convert use of typedef ctl_table to struct ctl_table
IB/cm: Convert to using idr_alloc_cyclic()
IB/mlx5: Fix page shift in create CQ for userspace
IB/mlx4: Fix device max capabilities check
IB/mlx5: Fix list_del of empty list
IB/mlx5: Remove dead code
IB/core: Encorce MR access rights rules on kernel consumers
IB/mlx4: Fix endless loop in resize CQ
RDMA/cma: Remove unused argument and minor dead code
RDMA/ucma: Discard events for IDs not yet claimed by user space
IB/core: Add Cisco usNIC rdma node and transport types
RDMA/nes: Remove self-assignment from nes_query_qp()
IB/srp: Report receive errors correctly
...
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
some robustness fixes for broken virtio devices, plus minor tweaks.
[vs last pull request: added the virtio-scsi broken vq escape patch, which
I somehow lost.]
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=vY2L
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"Nothing really exciting: some groundwork for changing virtio endian,
and some robustness fixes for broken virtio devices, plus minor
tweaks"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio_scsi: verify if queue is broken after virtqueue_get_buf()
x86, asmlinkage, lguest: Pass in globals into assembler statement
virtio: mmio: fix signature checking for BE guests
virtio_ring: adapt to notify() returning bool
virtio_net: verify if queue is broken after virtqueue_get_buf()
virtio_console: verify if queue is broken after virtqueue_get_buf()
virtio_blk: verify if queue is broken after virtqueue_get_buf()
virtio_ring: add new function virtqueue_is_broken()
virtio_test: verify if virtqueue_kick() succeeded
virtio_net: verify if virtqueue_kick() succeeded
virtio_ring: let virtqueue_{kick()/notify()} return a bool
virtio_ring: change host notification API
virtio_config: remove virtio_config_val
virtio: use size-based config accessors.
virtio_config: introduce size-based accessors.
virtio_ring: plug kmemleak false positive.
virtio: pm: use CONFIG_PM_SLEEP instead of CONFIG_PM
This patch set is driver updates for qla4xxx, scsi_debug, pm80xx, fcoe/libfc,
eas2r, lpfc, be2iscsi and megaraid_sas plus some assorted bug fixes and
cleanups.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJSfw30AAoJEDeqqVYsXL0MZPEIAK6GBHFw8JsU3NQ4SbM5hzdM
ywPryTn7DO9jyj0J04i6TNtbS6om9E8tjLyr3SnmTQNiTDXGv44rIEfJyHR9ko2n
E2hRu4xaGEWK4dkuktQuOqj2fuXRyeXr2maYIXjkmFI0hesLqozYKgLAeWTHvabE
2HICwG/lfCzesqVl69Y3V8n1vZvtJqAls6liwY09i9eSDRe39DynRn7bjLXzkPkc
ynjJYl22CIZ7nb+PgzqQ+xEUIdXqGG890CvGaqg7+x3ZUmmOtfECaDUkCjVeiiE6
sy72V6E4ET/YMrkhRmIUKyZxGbl/tMxYPuGaBhq2fSNRx8x1R+Ajfh9UM2AZTh4=
=hCHG
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This patch set is driver updates for qla4xxx, scsi_debug, pm80xx,
fcoe/libfc, eas2r, lpfc, be2iscsi and megaraid_sas plus some assorted
bug fixes and cleanups"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (106 commits)
[SCSI] scsi_error: Escalate to LUN reset if abort fails
[SCSI] Add 'eh_deadline' to limit SCSI EH runtime
[SCSI] remove check for 'resetting'
[SCSI] dc395: Move 'last_reset' into internal host structure
[SCSI] tmscsim: Move 'last_reset' into host structure
[SCSI] advansys: Remove 'last_reset' references
[SCSI] dpt_i2o: return SCSI_MLQUEUE_HOST_BUSY when in reset
[SCSI] dpt_i2o: Remove DPTI_STATE_IOCTL
[SCSI] megaraid_sas: Fix synchronization problem between sysPD IO path and AEN path
[SCSI] lpfc: Fix typo on NULL assignment
[SCSI] scsi_dh_alua: ALUA handler attach should succeed while TPG is transitioning
[SCSI] scsi_dh_alua: ALUA check sense should retry device internal reset unit attention
[SCSI] esas2r: Cleanup snprinf formatting of firmware version
[SCSI] esas2r: Remove superfluous mask of pcie_cap_reg
[SCSI] esas2r: Fixes for big-endian platforms
[SCSI] esas2r: Directly call kernel functions for atomic bit operations
[SCSI] lpfc 8.3.43: Update lpfc version to driver version 8.3.43
[SCSI] lpfc 8.3.43: Fixed not processing task management IOCB response status
[SCSI] lpfc 8.3.43: Fixed spinlock hang.
[SCSI] lpfc 8.3.43: Fixed invalid Total_Data_Placed value received for els and ct command responses
...
Pull block IO core updates from Jens Axboe:
"This is the pull request for the core changes in the block layer for
3.13. It contains:
- The new blk-mq request interface.
This is a new and more scalable queueing model that marries the
best part of the request based interface we currently have (which
is fully featured, but scales poorly) and the bio based "interface"
which the new drivers for high IOPS devices end up using because
it's much faster than the request based one.
The bio interface has no block layer support, since it taps into
the stack much earlier. This means that drivers end up having to
implement a lot of functionality on their own, like tagging,
timeout handling, requeue, etc. The blk-mq interface provides all
these. Some drivers even provide a switch to select bio or rq and
has code to handle both, since things like merging only works in
the rq model and hence is faster for some workloads. This is a
huge mess. Conversion of these drivers nets us a substantial code
reduction. Initial results on converting SCSI to this model even
shows an 8x improvement on single queue devices. So while the
model was intended to work on the newer multiqueue devices, it has
substantial improvements for "classic" hardware as well. This code
has gone through extensive testing and development, it's now ready
to go. A pull request is coming to convert virtio-blk to this
model will be will be coming as well, with more drivers scheduled
for 3.14 conversion.
- Two blktrace fixes from Jan and Chen Gang.
- A plug merge fix from Alireza Haghdoost.
- Conversion of __get_cpu_var() from Christoph Lameter.
- Fix for sector_div() with 64-bit divider from Geert Uytterhoeven.
- A fix for a race between request completion and the timeout
handling from Jeff Moyer. This is what caused the merge conflict
with blk-mq/core, in case you are looking at that.
- A dm stacking fix from Mike Snitzer.
- A code consolidation fix and duplicated code removal from Kent
Overstreet.
- A handful of block bug fixes from Mikulas Patocka, fixing a loop
crash and memory corruption on blk cg.
- Elevator switch bug fix from Tomoki Sekiyama.
A heads-up that I had to rebase this branch. Initially the immutable
bio_vecs had been queued up for inclusion, but a week later, it became
clear that it wasn't fully cooked yet. So the decision was made to
pull this out and postpone it until 3.14. It was a straight forward
rebase, just pruning out the immutable series and the later fixes of
problems with it. The rest of the patches applied directly and no
further changes were made"
* 'for-3.13/core' of git://git.kernel.dk/linux-block: (31 commits)
block: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
block: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
block: Do not call sector_div() with a 64-bit divisor
kernel: trace: blktrace: remove redundent memcpy() in compat_blk_trace_setup()
block: Consolidate duplicated bio_trim() implementations
block: Use rw_copy_check_uvector()
block: Enable sysfs nomerge control for I/O requests in the plug list
block: properly stack underlying max_segment_size to DM device
elevator: acquire q->sysfs_lock in elevator_change()
elevator: Fix a race in elevator switching and md device initialization
block: Replace __get_cpu_var uses
bdi: test bdi_init failure
block: fix a probe argument to blk_register_region
loop: fix crash if blk_alloc_queue fails
blk-core: Fix memory corruption if blkcg_init_queue fails
block: fix race between request completion and timeout handling
blktrace: Send BLK_TN_PROCESS events to all running traces
blk-mq: don't disallow request merges for req->special being set
blk-mq: mq plug list breakage
blk-mq: fix for flush deadlock
...
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
If virtqueue_get_buf() returned with a NULL pointer avoid a possibly
endless loop by checking for a broken virtqueue.
Signed-off-by: Heinz Graalfs <graalfs@linux.vnet.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Add support for periodically reconnecting to an SRP target until
the dev_loss timer expires. After the tenth reconnection attempt,
gradually slow down subsequent reconnect attempts.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add the necessary functions in the SRP transport module to allow an
SRP initiator driver to implement transport layer error handling
similar to the functionality already provided by the FC transport
layer. This includes:
- Support for implementing fast_io_fail_tmo, the time that should
elapse after having detected a transport layer problem and
before failing I/O.
- Support for implementing dev_loss_tmo, the time that should
elapse after having detected a transport layer problem and
before removing a remote port.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Keep the rport data structure around after srp_remove_host() has
finished until cleanup of the IB transport layer has finished
completely. This is necessary because later patches use the rport
pointer inside the queuecommand callback. Without this patch
accessing the rport from inside a queuecommand callback is racy
because srp_remove_host() must be invoked before scsi_remove_host()
and because the queuecommand callback could get invoked after
srp_remove_host() has finished. In other words, without this patch
the queuecommand callback can get invoked after the rport data
structure has been freed.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Here's the big driver core / sysfs update for 3.13-rc1.
There's lots of dev_groups updates for different subsystems, as they all
get slowly migrated over to the safe versions of the attribute groups
(removing userspace races with the creation of the sysfs files.) Also
in here are some kobject updates, devres expansions, and the first round
of Tejun's sysfs reworking to enable it to be used by other subsystems
as a backend for an in-kernel filesystem.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlJ6xAMACgkQMUfUDdst+yk1kQCfcHXhfnrvFZ5J/mDP509IzhNS
ddEAoLEWoivtBppNsgrWqXpD1vi4UMsE
=JmVW
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core / sysfs patches from Greg KH:
"Here's the big driver core / sysfs update for 3.13-rc1.
There's lots of dev_groups updates for different subsystems, as they
all get slowly migrated over to the safe versions of the attribute
groups (removing userspace races with the creation of the sysfs
files.) Also in here are some kobject updates, devres expansions, and
the first round of Tejun's sysfs reworking to enable it to be used by
other subsystems as a backend for an in-kernel filesystem.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (83 commits)
sysfs: rename sysfs_assoc_lock and explain what it's about
sysfs: use generic_file_llseek() for sysfs_file_operations
sysfs: return correct error code on unimplemented mmap()
mdio_bus: convert bus code to use dev_groups
device: Make dev_WARN/dev_WARN_ONCE print device as well as driver name
sysfs: separate out dup filename warning into a separate function
sysfs: move sysfs_hash_and_remove() to fs/sysfs/dir.c
sysfs: remove unused sysfs_get_dentry() prototype
sysfs: honor bin_attr.attr.ignore_lockdep
sysfs: merge sysfs_elem_bin_attr into sysfs_elem_attr
devres: restore zeroing behavior of devres_alloc()
sysfs: fix sysfs_write_file for bin file
input: gameport: convert bus code to use dev_groups
input: serio: remove bus usage of dev_attrs
input: serio: use DEVICE_ATTR_RO()
i2o: convert bus code to use dev_groups
memstick: convert bus code to use dev_groups
tifm: convert bus code to use dev_groups
virtio: convert bus code to use dev_groups
ipack: convert bus code to use dev_groups
...
DMA bounce limit is the maximum direct DMA'able memory beyond which
bounce buffers has to be used to perform dma operations. SCSI driver
relies on dma_mask but its calculation is based on max_*pfn which
don't have uniform meaning across architectures. So make use of
dma_max_pfn() which is expected to return the DMAable maximum pfn
value across architectures.
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In commit d496f94d22 ('[SCSI] aacraid: fix security weakness') we
added a check on CAP_SYS_RAWIO to the ioctl. The compat ioctls need the
check as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a command abort fails there is a fair chance that all other
aborts will be failing, too.
So we should be calling LUN reset directly after the first failed
abort and skip aborting the remaining commands.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patchs adds an 'eh_deadline' sysfs attribute to the scsi
host which limits the overall runtime of the SCSI EH.
The 'eh_deadline' value is stored in the now obsolete field
'resetting'.
When a command is failed the start time of the EH is stored
in 'last_reset'. If the overall runtime of the SCSI EH is longer
than last_reset + eh_deadline, the EH is short-circuited and
falls through to issue a host reset only.
[jejb: add comments in Scsi_Host about new fields]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Field is now unused, so this is dead code.
[jejb: remove resetting and last_reset from Scsi_Host]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We have officially run out of flags in a 32-bit space. Extend it
to 64-bit even on 32-bit archs.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
'last_reset' is only used internally, so move it into the
internal host structure.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The 'last_reset' value is only used internally, so move it into
the internal host structure.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When the HBA is in reset we should be returning 'busy' and not
rely on the obscure 'last_reset' feature.
[jejb: checkpatch fixes]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There is syncronization problem between sysPD IO path and AEN path. Driver
maintains instance->pd_list[] array, which will get updated(by calling
function megasas_get_pd_list[]), whenever any of below events occurs-
MR_EVT_PD_INSERTED
MR_EVT_PD_REMOVED
MR_EVT_CTRL_HOST_BUS_SCAN_REQUESTED
MR_EVT_FOREIGN_CFG_IMPORTED
At same time running sysPD IO will be accessing the same array
instance->pd_list[], which is getting updated in AEN path, because of this IO
may not get correct PD info from instance->pd_list[] array.
Signed-off-by: Adam Radford <adam.radford@lsi.com>
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In the lpfc_ct_free_iocb function after freeing associated memory to the
ctiocb->context3, the ctiocb->context1 is set to NULL instead of context3.
Signed-off-by: Felipe Pena <felipensp@gmail.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During testing, it was discovered that when a device tries to attach to the
alua handler while in TPG state of transitioning, the alua_rtpg function will
wait for it to exit the state before allowing it to continue. As a result, if
the 60 second timeout expires, the alua handler will not attach to the device.
To fix this, I have introduced an input argument to alua_rtpg called
wait_for_transition. The idea is that it will wait for the transition to
complete before an activation (because the current TPG state has some bearing
in that case), but during a discovery if it is transitioning, it will not
wait, and will store the state as standby for the time being.
I believe the precedent exists for this from commit
c0d289b3e5 Since if the device reports a state
of transitioning, it can transition to other more valid states, and it has
been established TPGS is supported on the device, if it is attaching.
Signed-off-by: Sean Stewart <Sean.Stewart@netapp.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When the scsi_dh_alua handler issues an RTPG during initialization, if it gets
0x06/0x29/0x04 as the sense, it will fail to attach the handler. NetApp
E-Series returns 0x29/0x00 for power on, and 0x29/0x04 for conditions that
cause the controller to reboot again. These conditions should be treated
identically within the handler.
Signed-off-by: Sean Stewart <Sean.Stewart@netapp.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This reverts commit 15b06f9a02.
This is one of four patches that was causing this bug
[ 205.372823] ================================================
[ 205.372901] [ BUG: lock held when returning to user space! ]
[ 205.372979] 3.12.0-rc6-hw-debug-pagealloc+ #67 Not tainted
[ 205.373055] ------------------------------------------------
[ 205.373132] megarc.bin/5283 is leaving the kernel with locks still held!
[ 205.373212] 1 lock held by megarc.bin/5283:
[ 205.373285] #0: (&sdp->o_sem){.+.+..}, at: [<ffffffff8161e650>] sg_open+0x3a0/0x4d0
Cc: Vaughan Cao <vaughan.cao@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This reverts commit 00b2d9d6d0.
This is one of four patches that was causing this bug
[ 205.372823] ================================================
[ 205.372901] [ BUG: lock held when returning to user space! ]
[ 205.372979] 3.12.0-rc6-hw-debug-pagealloc+ #67 Not tainted
[ 205.373055] ------------------------------------------------
[ 205.373132] megarc.bin/5283 is leaving the kernel with locks still held!
[ 205.373212] 1 lock held by megarc.bin/5283:
[ 205.373285] #0: (&sdp->o_sem){.+.+..}, at: [<ffffffff8161e650>] sg_open+0x3a0/0x4d0
Cc: Vaughan Cao <vaughan.cao@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This reverts commit e32c9e6300.
This is one of four patches that was causing this bug
[ 205.372823] ================================================
[ 205.372901] [ BUG: lock held when returning to user space! ]
[ 205.372979] 3.12.0-rc6-hw-debug-pagealloc+ #67 Not tainted
[ 205.373055] ------------------------------------------------
[ 205.373132] megarc.bin/5283 is leaving the kernel with locks still held!
[ 205.373212] 1 lock held by megarc.bin/5283:
[ 205.373285] #0: (&sdp->o_sem){.+.+..}, at: [<ffffffff8161e650>] sg_open+0x3a0/0x4d0
Cc: Vaughan Cao <vaughan.cao@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This reverts commit 1f962ebcdf.
This is one of four patches that was causing this bug
[ 205.372823] ================================================
[ 205.372901] [ BUG: lock held when returning to user space! ]
[ 205.372979] 3.12.0-rc6-hw-debug-pagealloc+ #67 Not tainted
[ 205.373055] ------------------------------------------------
[ 205.373132] megarc.bin/5283 is leaving the kernel with locks still held!
[ 205.373212] 1 lock held by megarc.bin/5283:
[ 205.373285] #0: (&sdp->o_sem){.+.+..}, at: [<ffffffff8161e650>] sg_open+0x3a0/0x4d0
Cc: Vaughan Cao <vaughan.cao@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In esas2r_format_init_msg(), sgl_page_size and epoch_time params
are converted to little endian and the firmware version read from
the hba is converted to cpu endianess.
In esas2r_rq_init_request, correct and simplify the construction
of the SCSI handle.
These fixes are the result of testing on a PPC64 machine.
Signed-off-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Previously the code embedded the kernel's test_bit/clear_bit
functions in wrappers that accepted u32 parameters. The
wrapper cast these parameters to longs before passing them
to the kernel's bit functions. This did not work properly
on platforms with 64-bit longs.
Signed-off-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch implements the changes requested by Jeremy Linton:
http://marc.info/?l=linux-scsi&m=136242124409687&w=2
The patch revises the command issuing behavior, detecting cases where the
Task Mgmt command may have completed but with a non-successful status, which it
previously treated as a successful TMF. The patch also corrects a flushing of
I/O that was done which should only be done on successful TMF completion.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Rather than having a separate constant for specifying the timeout on FLUSH
operations, use the basic I/O timeout value that is already configurable
on a per target basis to derive the FLUSH timeout. Looking at the current
definitions of these timeout values, the FLUSH operation is supposed to have
a value that is twice the normal timeout value. This patch preserves this
relationship while leveraging the flexibility of specifying the I/O timeout.
Based on a prior patch by KY Srinivasan <kys@microsoft.com>
Reviewed-by: KY Srinivasan <kys@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Supports below logging facilities,
Inbound outbound queues dump.
Non fatal dump in case of IO failures.
Fatal dump in case of firmware failure.
[jejb: checkpatch spacing fixes]
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
