The quirk was meant to just inhibit some resets, but ended up blocking
all of them. Fortunately, this was just what was needed. Change the
comment to reflect reality.
Also, this issue has just been observed on Samsung laptops, so reduce
the number of chips the quirk affects.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The limit was a fixed 100k limit in the busy loop, which is not
accurate. It would better to have time limit for the worst case
which occurs when sending 80 cycles at 400 kHz and takes about
200 microseconds, so limit the max time spend in the busy loop
for some 250 microseconds.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Use work queues for starting new commands instead of starting them
directly from irq handler. The command scheduling needs to be delayed
a bit for some cards which should not be done from an interrupt.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
MMCA spec says the mmc clock should be kept running for at least
8 cycles after the last RW request. Ensure this with lazy clock
disable after a request, or with an explicit delay before
switching a slot.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Abort failed command from workqueue rather than from an interrupt,
allowing longer delays in abortion.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The cover waitqueue is occasionally scheduled twice from timer
and the interrupt and oops follows. It would have been possible
to fix this problem with spinlocks but using tasklet was a dropin
solution with no need for locking.
This path also adds some cleanups.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
If the get_cover_state is not set, it occurs the oops.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Using setup_timer() instead of init_timer() on omap.c file.
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
When a card is removed while it is being accessed, a command can get stuck so
that no timeout or end of command interrupt ever occurs. The command getting
stuck is almost always CDM12, but also the other commands can get stuck. Catch
a stuck command with a timer and try sending the initialization stream until
the controller starts running again and responds with the end of command
status.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
General code cleanup, modifications at some dev_* functions and
other hacks at mmc_omap_irq() for MMC multislot support.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Modifications at power functions to MMC multislot support. This patch
also move board-specific code out of MMC OMAP driver.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Fix the data timeout calculation for MMC multislot support.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
New functions to support MMC multislot:
mmc_omap_release_dma() and mmc_omap_abort_xfer().
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds back MMC cover switch support in a way that
supports multiple slots.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Introduce new MMC multislot structure and change driver to use it.
Note that MMC clocking is now enabled in mmc_omap_select_slot()
and disabled in mmc_omap_release_slot().
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch removes the MMC cover switch handling temporarily
to make following multislot patches cleaner.
MMC cover switch handling will be added back in later patches
after adding basic multislot support.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
According with commit 255d01af9a
from Linux-OMAP tree, the BYTEBLOCK capability was removed by Pierre Ossman.
MMC_CAP_BYTEBLOCK is not defined causing the compile error:
drivers/mmc/host/omap.c: In function `mmc_omap_probe':
drivers/mmc/host/omap.c:1077: error: `MMC_CAP_BYTEBLOCK' undeclared (first use in this function)
drivers/mmc/host/omap.c:1077: error: (Each undeclared identifier is reported only once
drivers/mmc/host/omap.c:1077: error: for each function it appears in.)
Signed-off-by: Francisco Alecrim <francisco.alecrim@indt.org.br>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
As noted by Kyungmin Park, the divisor calculation has
an unnecessary increase.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch removes some opcodes from host driver so there's no need on putting
'#include <linux/mmc/mmc.h>', that should not be needed in host drivers.
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Hook up the controller LED to the LED subsystem, allowing more flexible
control than simply indicating an ongoing request.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Since 43cc71eed1, the platform modalias is
prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable MMC host
platform drivers, to re-enable auto loading.
Also, add missing owner declarations in driver init.
[dbrownell@users.sourceforge.net: registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for the Ricoh RL5c476 chip: with this
the mmc adapter that needs this disabler (R5C843) can also be
handled correctly when it sits on a RL5c476.
Signed-off-by: Frank Seidel <fseidel@suse.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Update the AT91 MMC driver to use the generic GPIO calls instead of the
AT91-specific calls; and to request (and release) those GPIO signals.
That required updating the probe() fault cleanup codepaths. Now there
is a single sequence for freeing resources, in reverse order of their
allocation. Also that code uses use dev_*() for messaging, and has less
abuse of KERN_ERR.
Likewise with updating remove() cleanup. This had to free the GPIOs,
and while adding that code I noticed and fixed two other problems: it
was poking at a workqueue owned by the mmc core; and in one (rare)
case would try freeing an IRQ that it didn't allocate.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some devices have several controllers; need add the index info to
device slot name host->slot_desc[]
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Both of these drivers work well (although some hardware still has
its problems) and are not in the "alpha" quality that EXPERIMENTAL
suggests.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
As pci config space is reinitialised on a suspend/resume cycle, the
disabler needs to work its magic at resume time. For symmetry this
change also explicitly enables the controller at suspend time but
it's not strictly necessary.
Signed-off-by: Philipl Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Move the tps65010 header file from the OMAP arch directory to the
more generic <linux/i2c/...> directory, and remove the spurious
dependency of this driver on OMAP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patchis to add the first mmc controller support for pxa3xx.
It's valid for pxa3[0|1|2]0.
On zylonite, the first controller supports two slots, this patch
only support the first one right now.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is to move pxamci DMA specific code to corresponding
platform layer because using DRCMRRXMMC/DRCMRTXMMC in pxamci.c makes
the driver code dedicated to platform which is not extensible.
It is applicable to all pxa platforms.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pxa3[0|1]0 mmc controller can support 26MHz clock mode, they support
SD spec 1.1 and MMC spec 4.0 which specify high speed mode. So host
caps will include MMC_CAP_MMC_HIGHSPEED and MMC_CAP_SD_HIGHSPEED for
pxa3[0|1]0.
This patch is to add 26MHz support for them. pxa host clock will be
set to 26MHz mode when the card supported max clock rate is higher
than or equal to 26MHz.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The JMicron JMB38x chip doesn't support transfers that aren't 32-bit
aligned (both size and start address). It also doesn't like switching
between PIO and DMA mode, so it needs to be reset after each request.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some controllers have been designed on the assumption that all transfers
will be 32-bit aligned, both in start address and in size. This is not a
guarantee the SDHCI specification provides and not one we can provide.
Revert back to PIO for individual requests in order to work around the
hardware bug.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Given the patch which simplifies the spi_sync calling convention, this one
updates the callers of that routine which tried using it according to the
previous specification. (Most didn't.)
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is possible to handle arbitrary block sizes with tifm card reader by
conditionally switching to PIO in case such block has to be delivered. At
the beginning of each request, DMA is either disabled (non-power-of-2 block
size) or set to load time user preference.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Fix:
WARNING: at arch/arm/mach-pxa/clock.c:69 clk_disable()
[<c002d7c8>] (dump_stack+0x0/0x14) from [<c00334f4>] (clk_disable+0x34/0xa0)
[<c00334c0>] (clk_disable+0x0/0xa0) from [<c028a43c>] (pxamci_set_ios+0x74/0xf0)
[<c028a3c8>] (pxamci_set_ios+0x0/0xf0) from [<c0281548>] (mmc_power_off+0x90/0x9c)
[<c02814b8>] (mmc_power_off+0x0/0x9c) from [<c0281a30>] (mmc_start_host+0x18/0x28)
[<c0281a18>] (mmc_start_host+0x0/0x28) from [<c02825a0>] (mmc_add_host+0xe8/0x104)
[<c02824b8>] (mmc_add_host+0x0/0x104) from [<c028a7d0>] (pxamci_probe+0x24c/0x2f4)
[<c028a584>] (pxamci_probe+0x0/0x2f4) from [<c01e5948>] (platform_drv_probe+0x20/0x24)
...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
#include <scatterlist/scatterlist.h>
is an odd thing to do...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch 49dce689ad changed the sysfs data
structures for SPI in a way which broke the MMC-over-SPI host driver.
This patch fixes that regression by changing the scheme used to keep
from knowingly trying to use a shared bus segment, and updates the
adjacent comments slightly to better explain the issue.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Do a full scan of the directory to try and be a bit more proactive,
instead of waiting for things to break.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Commits
58b053e4ce ("Update arch/ to use sg helpers")
45711f1af6 ("[SG] Update drivers to use sg helpers")
fa05f1286b ("Update net/ to use sg helpers")
converted many files to use the scatter gather helpers without ensuring
that the necessary headerfile <linux/scatterlist> is included. This
happened to work for ia64, powerpc, sparc64 and x86 because they
happened to drag in that file via their <asm/dma-mapping.h>.
On most of the others this probably broke.
Instead of increasing the header file spider web I choose to include
<linux/scatterlist.h> directly into the affectes files.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A small MMC driver cleanup.
Use the defined AT91_MCI_ERRORS in at91_mci_completed_command() instead
of specifying all the error bits individually.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
