This patch converts all FC_DBG statements to use new runtime tunable
debug macros. The fcoe.ko module now has a debug_logging module
parameter.
fcoe_debug_logging is an unsigned integer representing a bitmask of all
available logging levels. Currently only two logging levels are
supported-
bit
LSB 0 = general fcoe logging
1 = netdevice related logging
This patch also attempts to clean up some debug statement formatting
so it's more readable.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds support for setting the physical block exponent and
lowest aligned LBA in the READ CAPACITY(16) response.
The B0 VPD page is adjusted accordingly.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
NETDEVICES + NETDEV_1000 need to be enabled so that kconfig will check
those branches for selects and enforce "select UIO" under CNIC.
Otherwise the build fails with:
ERROR: "uio_unregister_device" [drivers/net/cnic.ko] undefined!
ERROR: "uio_event_notify" [drivers/net/cnic.ko] undefined!
ERROR: "__uio_register_device" [drivers/net/cnic.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
MSI has only been tested on and known to work with PCI-E based adapters. This
patch adds a field to struct ipr_chip_t to indicate which type of interrupt to
use based on what is known about the chip.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The return value from pci_enable_msi() can not always be trusted. This patch
adds code to generate an interrupt after MSI has been enabled and tests
whether or not we can receive and process it. If the tests fails, then fall
back to LSI.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There have been several bug reports which identified the Ultrium-3
tape as just hanging up on the bus during certain types of IU
transfer. The identified culpret is type 0x02 (MULTIPLE COMMAND)
transfers. The only way to prevent this tape wedging is to prevent it
from using IU transfers at all. So this patch uses the exported
blacklist matching technology to recognise the drive and force it not
to use IU transfers.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Right at the moment, we carefully set up the spi_support_xx in the
device configuration routines, but then we never actually use the
results: we rely on the inquiry strings. If we're going to allow
overrides to the inquiry data, we have to rely on our own internal
settings.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The current scsi_devinfo.c matching routines use a single table for
the global blacklist. However, we're developing a need to blacklist
from specific transports too (notably some tape drives using SPI which
don't respond well to high speed protocols). Instead of developing
separate blacklist matching for each transport class needing it,
enhance the current list matching to permit multiple lists.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Pre-ISP24xx chips have dedicated uses for mailbox 4 and 5 which
software should typically not query nor update.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* To set iiDMA speeds for ISP81XX, bits 5-0 are used whereas for
other older ISPs bits 2-0 are used.
* Pass proper VP index
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Just once, two fcoe instances got the same host number
from scsi_add_host().
Use atomic_t and atomic_inc_return() to get next host number.
Subtract 1, so that scsi_host still starts with 0.
[jejb: added comment about unusual subtraction]
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We need to call blk_end_request_all to complete SMP requests properly.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Allow the user to control the debug logs in libiscsi. We will now
have a module param for connection, session & error handling.
[Mike Christie - Fixed up to compile on current code and added
missing ISCSI_DBG_EH conversions]
Signed-off-by: Erez Zilber <erezzi.list@gmail.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The net layer might return -EAGAIN because it could not
get space/mem within the sock sndtimeo or becuase the tcp/ip
connection was down. For the latter we do not want to retry
because the conn/session should just be shutdown and restarted.
libiscsi knows the state of the session recovery so propogate
this error to that layer. It will either do iscsi recovery
or have us retry the operation. Right now if we have partially
sent a pdu we would always retry the IO xmit slowing down
recovery.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If we are sending or receiving data for the task successfully do
not run the scsi eh, because we know the task is making progress.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The default kernel pages supported are 4K, 8K, 16K, and 64K. Re-calculate
entries if PAGE_SIZE is not one of the defaults.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The iscsi ddp functionality could be used by multiple iscsi entities,
add a refcnt to keep track of it, so we would not release it pre-maturely.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Query the block limits VPD page and adjust queue minimum and optimal I/O
sizes.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Detect non-rotational devices and set the queue flag accordingly.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Extract physical block size and lowest aligned LBA from READ
CAPACITY(16) response and adjust queue parameters.
Report physical block size and alignment when applicable.
[jejb: fix up trailing whitespace]
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6:
[SCSI] aic79xx: make driver respect nvram for IU and QAS settings
[SCSI] don't attach ULD to Dell Universal Xport
[SCSI] lpfc 8.3.3 : Update driver version to 8.3.3
[SCSI] lpfc 8.3.3 : Add support for Target Reset handler entrypoint
[SCSI] lpfc 8.3.3 : Fix a couple of spin_lock and memory issues and a crash
[SCSI] lpfc 8.3.3 : FC/FCOE discovery fixes
[SCSI] lpfc 8.3.3 : Fix various SLI-3 vs SLI-4 differences
[SCSI] qla2xxx: Resolve a performance issue in interrupt
[SCSI] cnic, bnx2i: Fix build failure when CONFIG_PCI is not set.
[SCSI] nsp_cs: time_out reaches -1
[SCSI] qla2xxx: fix printk format warnings
[SCSI] ncr53c8xx: div reaches -1
[SCSI] compat: don't perform unneeded copy in sg_io code
[SCSI] zfcp: Update FC pass-through support
[SCSI] zfcp: Add FC pass-through support
[SCSI] FC Pass Thru support
Many developers use "/debug/" or "/debugfs/" or "/sys/kernel/debug/"
directory name to mount debugfs filesystem for ftrace according to
./Documentation/tracers/ftrace.txt file.
And, three directory names(ex:/debug/, /debugfs/, /sys/kernel/debug/) is
existed in kernel source like ftrace, DRM, Wireless, Documentation,
Network[sky2]files to mount debugfs filesystem.
debugfs means debug filesystem for debugging easy to use by greg kroah
hartman. "/sys/kernel/debug/" name is suitable as directory name
of debugfs filesystem.
- debugfs related reference: http://lwn.net/Articles/334546/
Fix inconsistency of directory name to mount debugfs filesystem.
* From Steven Rostedt
- find_debugfs() and tracing_files() in this patch.
Signed-off-by: GeunSik Lim <geunsik.lim@samsung.com>
Acked-by : Inaky Perez-Gonzalez <inaky@linux.intel.com>
Reviewed-by : Steven Rostedt <rostedt@goodmis.org>
Reviewed-by : James Smart <james.smart@emulex.com>
CC: Jiri Kosina <trivial@kernel.org>
CC: David Airlie <airlied@linux.ie>
CC: Peter Osterlund <petero2@telia.com>
CC: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
CC: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
CC: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Cc: linux-scsi@vger.kernel.org
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Brian King <brking@linux.vnet.ibm.com>
Cc: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Cc: linux-scsi@vger.kernel.org
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch allows the Adaptec firmware to pass on its values for Packetize and
QAS. To do this, the settings max_iu and max_qas have been introduced into
the SPI transport class and populated from the adaptec NVram tables. Domain
validation in the SPI transport class will respect the max settings when
configuring to the highest possible speed for testing.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We already have blacklists for SGI, IBM and SUN versions of this; apparently
there's a Dell version too.
Reported-by: Thomas Witzel <witzel.thomas@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Patch was originally submitted upstream on 4/21/2008:
http://marc.info/?l=linux-scsi&m=120880973719266&w=2
Somewhere, it never get merged. The patch restructures the task mgmt
routines, commonizing like behavior. Then the patch changes device
reset to LUN resets, and adds a target reset handler.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Contains the following changes:
- Fixed error paths retaking a spin lock which they already hold
- Added code to free memory in a couple of error paths
- Added code to free RPI bit map while unloading driver
- Added code to write zero to memory object allocated through dma_alloc_coherent
- Fixed crash/hang with target or LUN resets
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Contains the following changes:
- Force vport to send LOGO to fabric controller when deleting vport
- Fixed driver failing to register login when a PLOGI is received
- Fixes for FIP discovery
- Added stricter checks for FCF addressing mode
- Added code to send only FLOGI, FDISC and LOGO to Fabric controller as FIP
- Fixed handling of LOGO from Fabric port
- Fixed consecutive link up events skipped link_down processing
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Contains the following changes
- Set the CT field of FDISC to 3
- Fixed over allocation of SCSI buffers on SLI4
- Removed unused jump table entries
- Increase LPFC_WQE_DEF_COUNT to 256
- Updated FDISC context to VPI
- Fixed immediate SCSI command for LUN reset translation to WQE
- Extended mailbox handling to allow MBX_POLL commands in between async
MBQ commands
- Fixed SID used for FDISC
- Fix crash when accessing ctlregs from sysfs for SLI4 HBAs
- Fix SLI4 firmware version not being saved or displayed correctly
- Expand CQID field in WQE structure to 16 bits
- Fix post header template mailbox command timing out
- Removed FCoE PCI device ID 0x0705
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reverted back a change in qla*_intr_handler code that caused an increase in
cpu cycles by allowing interrupts to occur while the instance hardware lock
was being held. Fix by taking the lock in irqsave mode.
Reported-and-tested-by: Douglas W. Styner <douglas.w.styner@intel.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
CNIC and BNX2I must depend on PCI. Dependencies do not get
propagated through select.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
With a postfix decrement timeouts will reach -1 rather than 0, so the
errors do not appear.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix qla2xxx printk format warnings:
drivers/scsi/qla2xxx/qla_sup.c:915: warning: long long unsigned int format, u64 arg (arg 5)
drivers/scsi/qla2xxx/qla_sup.c:915: warning: long long unsigned int format, u64 arg (arg 6)
drivers/scsi/qla2xxx/qla_sup.c:923: warning: long long unsigned int format, u64 arg (arg 5)
drivers/scsi/qla2xxx/qla_sup.c:923: warning: long long unsigned int format, u64 arg (arg 6)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Attached is the ELS/CT pass-thru patch for the FC Transport. The patch
creates a generic framework that lays on top of bsg and the SGIO v4 ioctl
in order to pass transaction requests to LLDD's.
The interface supports the following operations:
On an fc_host basis:
Request login to the specified N_Port_ID, creating an fc_rport.
Request logout of the specified N_Port_ID, deleting an fc_rport
Send ELS request to specified N_Port_ID w/o requiring a login, and
wait for ELS response.
Send CT request to specified N_Port_ID and wait for CT response.
Login is required, but LLDD is allowed to manage login and decide
whether it stays in place after the request is satisfied.
Vendor-Unique request. Allows a LLDD-specific request to be passed
to the LLDD, and the passing of a response back to the application.
On an fc_rport basis:
Send ELS request to nport and wait for ELS response.
Send CT request to nport and wait for CT response.
The patch also exports several headers from include/scsi such that
they can be available to user-space applications:
include/scsi/scsi.h
include/scsi/scsi_netlink.h
include/scsi/scsi_netlink_fc.h
include/scsi/scsi_bsg_fc.h
For further information, refer to the last RFC:
http://marc.info/?l=linux-scsi&m=123436574018579&w=2
Note: Documentation is still spotty and will be added later.
[bharrosh@panasas.com: update for new block API]
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Conflicts:
drivers/message/fusion/mptsas.c
fixed up conflict between req->data_len accessors and mptsas driver updates.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* 'for-2.6.31' of git://git.kernel.dk/linux-2.6-block: (153 commits)
block: add request clone interface (v2)
floppy: fix hibernation
ramdisk: remove long-deprecated "ramdisk=" boot-time parameter
fs/bio.c: add missing __user annotation
block: prevent possible io_context->refcount overflow
Add serial number support for virtio_blk, V4a
block: Add missing bounce_pfn stacking and fix comments
Revert "block: Fix bounce limit setting in DM"
cciss: decode unit attention in SCSI error handling code
cciss: Remove no longer needed sendcmd reject processing code
cciss: change SCSI error handling routines to work with interrupts enabled.
cciss: separate error processing and command retrying code in sendcmd_withirq_core()
cciss: factor out fix target status processing code from sendcmd functions
cciss: simplify interface of sendcmd() and sendcmd_withirq()
cciss: factor out core of sendcmd_withirq() for use by SCSI error handling code
cciss: Use schedule_timeout_uninterruptible in SCSI error handling code
block: needs to set the residual length of a bidi request
Revert "block: implement blkdev_readpages"
block: Fix bounce limit setting in DM
Removed reference to non-existing file Documentation/PCI/PCI-DMA-mapping.txt
...
Manually fix conflicts with tracing updates in:
block/blk-sysfs.c
drivers/ide/ide-atapi.c
drivers/ide/ide-cd.c
drivers/ide/ide-floppy.c
drivers/ide/ide-tape.c
include/trace/events/block.h
kernel/trace/blktrace.c
* 'tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (244 commits)
Revert "x86, bts: reenable ptrace branch trace support"
tracing: do not translate event helper macros in print format
ftrace/documentation: fix typo in function grapher name
tracing/events: convert block trace points to TRACE_EVENT(), fix !CONFIG_BLOCK
tracing: add protection around module events unload
tracing: add trace_seq_vprint interface
tracing: fix the block trace points print size
tracing/events: convert block trace points to TRACE_EVENT()
ring-buffer: fix ret in rb_add_time_stamp
ring-buffer: pass in lockdep class key for reader_lock
tracing: add annotation to what type of stack trace is recorded
tracing: fix multiple use of __print_flags and __print_symbolic
tracing/events: fix output format of user stack
tracing/events: fix output format of kernel stack
tracing/trace_stack: fix the number of entries in the header
ring-buffer: discard timestamps that are at the start of the buffer
ring-buffer: try to discard unneeded timestamps
ring-buffer: fix bug in ring_buffer_discard_commit
ftrace: do not profile functions when disabled
tracing: make trace pipe recognize latency format flag
...
* Delete Makefile. It is only used for out-of-tree compilation
and was never needed. It slipped in by mistake.
* Remove from Kbuild all the out of tree stuff as promised.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
libosd has it's own sense decoding and printout. Don't
let scsi_lib duplicate that printout. (Which is done wrong
in regard to osd commands)
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch was inspired by Al Viro, for simplifying and fixing the
retrieval of osd-devices by in-kernel users, eg: file systems.
In-Kernel users, now, go through the same path user-mode does by
opening a file on the osd char-device and though holding a reference
to both the device and the Module.
A file pointer was added to the osd_dev structure which is now
allocated for each user. The internal osd_dev is no longer exposed
outside of the uld. I wanted to do that for a long time so each
libosd user can have his own defaults on the device.
The API is left the same, so user code need not change.
It is no longer needed to open/close a file handle on the osd
char-device from user-mode, before mounting an exofs on it.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
CC: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
libosd users that need to work with bios, must sometime use
the request_queue associated with the osd_dev. Make a wrapper for
that, and convert all in-tree users.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For supporting of chained-bios we can not inspect the first
bio only, as before. Caller shall pass the total length of the
request, ie. sum_bytes(bio-chain).
Also since the bio might be a chain we don't set it's direction
on behalf of it's callers. The bio direction should be properly
set prior to this call. So fix a couple of write users that now
need to set the bio direction properly
[In this patch I change both library code and user sites at
exofs, to make it easy on integration. It should be submitted
via James's scsi-misc tree.]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
CC: Jeff Garzik <jeff@garzik.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
_osd_req_finalize_data_integrity was trying to deduce the number of
out_bytes from passed osd_request->out.bio. This is wrong when
the bio is chained. The caller of _osd_req_finalize_data_integrity
has more ready available information and should just pass it.
Also in the light of future support for CDB-continuation segment this is
a better solution.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
By popular demand, define usefull wrappers for osd_req_read/write
that recieve kernel pointers. All users had their own.
Also remove these from exofs
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Shorten out the Attributes names.
Align all results on column 24.
Print system ID in a new line.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
New iSCSI driver for Broadcom BNX2 devices. The driver interfaces with
the CNIC driver to access the hardware.
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add ISCSI_NETLINK messages for iSCSI NICs to get information such as
path from userspace. Original iscsid messages are now always sent as
multicast to group 1. The new messages are sent to group 2.
The multicast changes were made by Mike Christie.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add support to ibmvscsi for the capabilities MAD. This command gets sent
to the Virtual I/O server prior to login in order to communicate client
capabilities. Additionally it returns information regarding capabilities
that the server supports. The two main capabilities communicated in this
MAD are related to partition migration and client reserve. Client reserve
allows for SCSI-2 reservations to be sent to virtual disks which are backed
by physical LUNs and will result in the reservation being sent to the
physical LUN.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
A new mode of error reporting, fast fail, has been added to the VIOS
which allows failover to happen more quickly.
If this new fast fail mode is enabled on the VIOS and the vSCSI client
supports the mode, the VIOS will not return MEDIUM error on path failures,
but rather return VIOSRP_ADAPTER_FAIL in the crq response, which
ibmvscsi will translate to DID_ERROR.
This new mode can be enabled for single path configurations as well,
so it is the new default error reporting mode. A module parameter is
provided to disable this new behavior on the off chance it causes a
problem on some old VIOS version.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ibmvscsi driver currently sends the SRP Login before sending the Adapter
Info MAD, which can result in commands getting sent to the virtual adapter
before we are ready for them. This results in a slight window where the target
devices may not behave as expected. Change the order and close the window.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Previously we had one timeout that was used for all types of operations.
This adds specific timeout values for different operations (init, login,
adapter info MAD, abort task, and LUN reset).
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Adds support for 16 byte CDBs to the ibmvscsi driver.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Ensure MPS remains in synchronization across all NIC/FCoE
functions after a reset.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Queued work processing will now be serialized with its own
lower-priority spinlock. This also simplifies the work-queue
interface for future work-queue consumers.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As firmware will ultimately terminate (stop) and port
states-cleared.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ISP24xx and above must query the host-status register, not HCCR.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ISP24xx and above ISPs perform a RISC reset in
qla24xx_reset_chip(), which is called prior to
qla24xx_chip_diag().
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
With RSCN states not being kept across qla2x00_configure_loop()
invocations, loop-resync distruptions during fabric-discovery may
cause ports to remain in a lost state. Force state
renegotiation during a follow-on configure-loop iteration.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Unlike earlier ISPs, recent ISPs (ISP81xx) can in fact fail this
mailbox command.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch fixes a NULL pointer bug that occurs when IO is being
carried out on a vport for which the cpu affinity mode is turned on.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The SCSI-midlayer's fast-fail codes consider an DID_ERROR status
as a driver-error and the failed I/O would then be retried in the
midlayer without being fast-failed to dm-multipath. DID_BUS_BUSY
status returns would induce unneeded path-failures events being
propagated to the DM/MD.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In case the onboard firmware is unable to be read or loaded for
operation, attempt to fallback to a limited-operational firmware
image stored in a different flash region. This will allow a user
to reflash and correct a board with proper operational firmware.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Firmware currently provides PB and PGF TLVs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This is not required as VLAN header is added by device
interface driver, this was causing bad FC_CRC in FCoE pkts when
using VLAN interface.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Removes periodic fcoe_watchdog timer used across all fcoe interface
maintained in fcoe_hostlist instead added new fcoe_queue_timer
per fcoe interface.
Added timer is armed only when some pending skb need to be flushed
as oppose to periodic 1 second fcoe_watchdog, since now
fcoe_queue_timer is used on demand thus set this to 2 jiffies.
Now fcoe_queue_timer is much simple than fcoe_watchdog using lock to
process all fcoe interface from fcoe_hostlist.
I noticed +ve performance result with using 2 jiffies timer as
this helps flushing fcoe_pending_queue quickly.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently fcoe_pending_queue.lock held twice for every new skb
adding to this queue when already least one pkt is pending in this
queue and that is not uncommon once skb pkts starts getting queued
here upon fcoe_start_io => dev_queue_xmit failure.
This patch moves most fcoe_pending_queue logic to fcoe_check_wait_queue
function, this new logic grabs fcoe_pending_queue.lock only once to
add a new skb instead twice as used to be.
I think after this patch call flow around fcoe_check_wait_queue
calling in fcoe_xmit is bit simplified with modified
fcoe_check_wait_queue function taking care of adding and
removing pending skb in one function.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When a sequence is received in response to an exchange we issued previously,
we should check to see if the exchange has completed. If yes, the sequence
should be discarded. Since the exchange might be still in the completion
process, it should be untouched.
Signed-off-by: Steve Ma <steve.ma@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If we aborted a command, because it timed out we should not use
DID_ABORT. It will fail the command right away back to the upper
layer. We want to use something that indicated that the problem
did not complete normally, but it was not a fatal problem.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
FIP frames should leave the fcoe layer with skb->protocol set to
ETH_P_FIP, not ETH_P_802_3.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When a reset is sent using fcoeadm on a non-FIP mode NIC,
there's no link flap, so the fcoe_ctlr stays in non-FIP mode.
In that case, FIP wasn't setting the flogi_oxid or map_dest flag,
causing the FLOGI to be sent with the both wrong source MAC and
the wrong destination MAC address, causing it to fail.
This leads to a non-functioning HBA until a link flap or
instance delete/create.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This driver needs dst_cache->dev so it should include net/dst.h
to ensure that it builds. While net/tcp.h probably includes it
already, we shouldn't rely on that since there is no guarantee
that this won't change in future.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There are several scenarios where the ibmvfc driver needs to
try to log back into a target on the fabric. Today when these events
occur, we simply go through re-discovery for all attached targets,
assuming that either the query of the name server or an ADISC will
indicate we might need to log back into the target, which doesn't
work for all scenarios. Fix this by taking note of the affected target(s)
in these conditions and ensuring we try to PLOGI back into the target.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For certain scenarios during device rediscovery, we detect we need
to log back into a target. Currently we do just that - PLOGI/PRLI
back into the target. Change the code to delete and add the target
from the FC transport layer as well, to ensure we handle any cases
where the target may have changed.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The virtual I/O server controlling the NPIV adapter associated with
a virtual fibre channel adapter can send a HALT event to the client.
When this occurs, the client can no longer send commands until a RESUME
is received. By adding support for flush on halt, we will get all of
our outstanding commands flushed back before the Virtual I/O server
enters the halt state, eliminating potential command timeouts for
outstanding commands which might occur if we did not support this feature.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds support for a new command supported by the Virtual I/O
Server, NPIV Logout. The command will abort all outstanding commands
and log out of the fabric. Currently, the only way to do this is
by breaking the CRQ, which can take a fairly long time when lots of
commands are outstanding. The NPIV Logout commands provides a mechanism
to accomplish virtually the same function, but is much faster.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ibmvfc driver currently logs errors during discovery for several
transient fabric errors, which generally get retried. If retries
do not work, we see multiple errors in the log. If retries do work,
we see errors in the log which may be confusing since the retry worked.
This patch enhances the discovery time error logging to only log errors
for command failures during discovery if all allowed retries have been
used up. The existing behavior of logging all failures can be restored
by setting the hosts log_level to a value of 3 or greater.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Use DEVICE_ATTR macro for defining device sysfs attributes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Since target allocations can occur while resetting the virtual adapter,
we shouldn't be using GFP_KERNEL for them as it could hang. Switch to
use GFP_NOIO.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix an obvious bug in processing error responses for SCSI commands
which can result in successful responses being incorrectly returned
with DID_ERROR.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The async split up of probing in sd.c created a potential failure case where
something goes wrong with device_add(), but which we don't recover properly.
Since, in general, asynchronous error handling is hard, move the device_add()
into the asynchronous path (it should be fast) and make sure all the deferred
processing cannot fail.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The Documentation is incorrect (we removed some functions referred to), and
none of the bug warnings now apply. Additionally remove the spurious check on
the return from blk_get_request() which can't fail if __GFP_WAIT is passed in.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add support for persistent vport definitions at creation at boot time
Also includes a few misc fixes for:
- conversion to vpi name from vport slang name
- couple of small mailbox references
- some additional discovery mods
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Miscellaneous Changes:
- Convert from SLI2_ACTIVE flag to more correct SLI_ACTIVE (generic) flag
- Reposition log verbose messaging definitions
- Update naming for vpi object name from vport slang name
- Handle deferred error attention condition
- Add 10G link support
- Small bug fixup
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update of copyrights on modified files
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
SLI4 supports both FC and FCOE, with some extended topology objects.
This patch adss support for the objects, and updates the disovery
engines for their use.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The mailbox commands themselves are the same, or very similar to
their SLI3 counterparts. This patch genericizes mailbox command
handling and adds support for the new SLI4 mailbox queue.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Adds support for the new queues in the SLI-4 interface. There are :
- Work Queues - host-to-adapter for fast-path traffic
- Mailbox Queues - host-to-adapter for control (slow-path)
- Buffer Queues - host-to-adapter for posting buffers for async receive
- Completion Queues - adapter-to-host for posting async events,
completions for fast or slow patch work, receipt of async
receive traffic
- Event Queues - tied to MSI-X vectors, binds completion queues with
interrupts
These patches add the all the support code to tie into command submission
and response paths, updates the interrupt handling, etc.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Adds new hardware and interface definitions.
Adds new interface routines - utilizing the reorganized layout of the
driver. Adds SLI-4 specific functions for attachment, initialization,
teardown, etc.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Preps the organization of the driver so that the bottom half, which
interacts with the hardware, can share common code sequences for
attachment, detachment, initialization, teardown, etc with new hardware.
For very common code sections, which become specific to the interface
type, the driver uses an indirect function call. The function is set at
initialization. For less common sections, such as initialization, the
driver looks at the interface type and calls the routines relative to
the interface.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch converts unicast address list to standard list_head using
previously introduced struct netdev_hw_addr. It also relaxes the
locking. Original spinlock (still used for multicast addresses) is not
needed and is no longer used for a protection of this list. All
reading and writing takes place under rtnl (with no changes).
I also removed a possibility to specify the length of the address
while adding or deleting unicast address. It's always dev->addr_len.
The convertion touched especially e1000 and ixgbe codes when the
change is not so trivial.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 13 +--
drivers/net/e1000/e1000_main.c | 24 +++--
drivers/net/ixgbe/ixgbe_common.c | 14 ++--
drivers/net/ixgbe/ixgbe_common.h | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/ixgbe/ixgbe_type.h | 4 +-
drivers/net/macvlan.c | 11 +-
drivers/net/mv643xx_eth.c | 11 +-
drivers/net/niu.c | 7 +-
drivers/net/virtio_net.c | 7 +-
drivers/s390/net/qeth_l2_main.c | 6 +-
drivers/scsi/fcoe/fcoe.c | 16 ++--
include/linux/netdevice.h | 18 ++--
net/8021q/vlan.c | 4 +-
net/8021q/vlan_dev.c | 10 +-
net/core/dev.c | 195 +++++++++++++++++++++++++++-----------
net/dsa/slave.c | 10 +-
net/packet/af_packet.c | 4 +-
18 files changed, 227 insertions(+), 137 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows fnic to configure number of retries for lport and rport
separately.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Acked-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This fix's is for all local function so their name has the "_" preceeding
the module name, then function name. Most the code is already is using this
naming convention.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch will find an active mid for a query_task request via the ioctl path.
This code is already there for task_abort, so this patch combining code using
the same fuction _ctl_set_task_mid(), previously _ctl_do_task_abort().
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Adding new eh_target_reset_handler for target reset. Change the
eh_device_reset_handler so its sending
MPI2_SCSITASKMGMT_TASKTYPE_LOGICAL_UNIT_RESET, instead of
MPI2_SCSITASKMGMT_TASKTYPE_TARGET_RESET. Add new function
_scsih_scsi_lookup_find_by_lun as a sanity check to insure I_T_L commands are
completed upon completing lun reset.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This add support for type 1 and 3 DIF support per the Oracle API.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Ying Chu <jasonchu@marvell.com>
Signed-off-by: Andy Yan <ayan@marvell.com>
Signed-off-by: Ke Wei <kewei@marvell.com
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch just adds some debug statements for the abort
and completion paths.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If a task did not complete normally due to a TMF, libiscsi will
now complete the task with the state ISCSI_TASK_ABRT_TMF. Drivers
like bnx2i that need to free resources if a command did not complete normally
can then check the task state. If a driver does not need to send
a special command if we have dropped the session then they can check
for ISCSI_TASK_ABRT_SESS_RECOV.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Instead of having libiscsi check if the offload bit is set, have
it check if the lld created a work queue. I think this is more
clear.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If the session is failed, but we have not yet fully transitioned
to the recovery stage we were still queueuing IO. The idea is
that for some failures we can recvover at the command level
and still continue to execute other IO. Well, we never have
added the recovery within a command code, so queueing up IO here
just creates the possibility that it might time time out so
this just has us requeue the IO the scsi layer for now.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bnx2i needs to send a hardware specific cleanup command if
a command has not completed normally (iscsi/scsi response from
target), and the session is still ok (this is the case when we
send a TMF to stop the command).
At this time it will need to drop the session lock. The problem
with the current code is that fail_all_commands assumes we
will hold the lock the entire time, so it uses list_for_each_entry_safe.
If while bnx2i drops the session lock multiple cmds complete then
list_for_each_entry_safe will not handle this correctly.
This patch removes the running lists and just has us loop over
the cmds array (in later patches we will then replace that
array with a block tag map at the session level). It also fixes
up the completion path so that if the TMF code and the normal recv
path were completing the same command then they both do not try
to do release the refcount taken when the task is queued.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If we have not got any pdus for recv_timeout seconds, then we will
send a iscsi ping/nop to make sure the target is still around. The
problem is if this is a slow link, and the ping got queued after
the data for a data_out (read), then the transport code could think
the ping has failed when it is just slowly making its way through
the network. This patch has us check if we are making progress while
the nop is outstanding. If we are still reading in data, then we
do not fail the session at that time.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Everytime we read in a pdu libiscsi will update a tracking field.
It uses this to decide when to check if the transport might be bad.
If we have not got data in recv_timeout seconds then we will
send a iscsi ping/nop.
If we are on a slow link then it could take a while to read in all
the data for a data_in. In that case we might send a ping/nop when
we do not need to or we might drop a session thinking it is bad
when the lower layer is making forward progress on it.
This patch has libiscsi_tcp update the recv tracking for each skb
(basically network packet from our point of view) instead of the
entire iscsi pdu+data, so we account for these cases where data is
coming in slowly.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If we are responding to a nop from the target by sending our nop,
and the session is getting torn down, then iscsi_start_session_recovery
could set the conn stop bits while the recv path is sending the nop
response and we will hit the bug ons in __iscsi_conn_send_pdu.
This has us check the state in __iscsi_conn_send_pdu and fail all
incoming mgmt IO if we are not logged in and if the pdu is not login
related. It also changes the ordering of the setting of conn stop state
bits so they are set after the session state is set (both are set under
the session lock).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This has iscsi_data_in_rsp call iscsi_update_cmdsn when a pdu is
completed like is done for other pdu's that are don.
For libiscsi_tcp, this means that it calls iscsi_update_cmdsn when
it is handling the pdu internally to only transfer data, but if there is
status then it does not need to call it since the completion handling
will do it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bnx2i needs to be able to look up mgmt task like login and nop, because
it does some processing of them on the completion path. This exports
iscsi_itt_to_task so it can look up the task.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If we could not allocate the initiator name or some other id like
the hwaddress or netdev, then userspace could deal with the failure
by just running in a dregraded mode.
Now we want to be able to switch values for the params and we
want some feedback, so this patch will check if a string like
the initiatorname could not be allocated and return an error.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bnx2i does not have one. It currently preallocates the bdt
when the session is setup.
We probably want to change that to a dma pool, then allocate from
the pool in the alloc pdu. Until then check if there is a alloc
pdu callout.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When we create the tcp/ip connection by calling ep_connect, we currently
just go by the routing table info.
I think there are two problems with this.
1. Some drivers do not have access to a routing table. Some drivers like
qla4xxx do not even know about other ports.
2. If you have two initiator ports on the same subnet, the user may have
set things up so that session1 was supposed to be run through port1. and
session2 was supposed to be run through port2. It looks like we could
end with both sessions going through one of the ports.
Fixes for cxgb3i from Karen Xie.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
drivers/scsi/NCR_D700.c: In function `NCR_D700_probe':
drivers/scsi/NCR_D700.c:322: warning: passing argument 2 of `request_irq' from incompatible pointer type
drivers/scsi/NCR_D700.c:322: warning: passing argument 2 of `request_irq' from incompatible pointer type
drivers/scsi/NCR_D700.c:322: warning: passing argument 2 of `request_irq' from incompatible pointer type
Signed-off-by: Zhenwen Xu <helight.xu@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Using sticky field to improve retrieve performance by eliminating some
lookups in . Remove some spurious casts.
Signed-off-by: Ying Chu <jasonchu@marvell.com>
Signed-off-by: Andy Yan <ayan@marvell.com>
Signed-off-by: Ke Wei <kewei@marvell.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Utilize DECLARE_BITMAP to define the tags array.
Signed-off-by: Ying Chu <jasonchu@marvell.com>
Signed-off-by: Andy Yan <ayan@marvell.com>
Signed-off-by: Ke Wei <kewei@marvell.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Null pointer check to avoid corruption.
Signed-off-by: Ying Chu <jasonchu@marvell.com>
Signed-off-by: Andy Yan <ayan@marvell.com>
Signed-off-by: Ke Wei <kewei@marvell.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
TMF task should be issued with Interrupt Disabled, or Deadlock may take place.
Clean-up unused parameters and conditonal lock.
Signed-off-by: Ying Chu <jasonchu@marvell.com>
Signed-off-by: Andy Yan <ayan@marvell.com>
Signed-off-by: Ke Wei <kewei@marvell.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Correct frame type setting according to parameter.
Signed-off-by: Ying Chu <jasonchu@marvell.com>
Signed-off-by: Andy Yan <ayan@marvell.com>
Signed-off-by: Ke Wei <kewei@marvell.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ipr driver can hang if it encounters enough PCI errors
to trigger the permanent error handler. The driver will attempt
to initiate a "bringdown" of the adapter and fail all pending
ops back. However, this bringdown is unlike any other bringdown
of the adapter in the code as the driver. In this code path we
end up failing back ops with allow_cmds still set to 1. This results
in some commands, the HCAM commands in particular, getting immediately
re-issued to the adapter on the done call, which results in
an infinite loop in ipr_fail_all_ops. Fix this by setting allow_cmds
to zero in this path.
Signed-off-by: Kleber S. Souza <klebers@linux.vnet.ibm.com>
[brking@linux.vnet.ibm.com: alternate patch substituted]
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
I had to set CONFIG_SCSI_MULTI_LUN to y in order to get my SE W595
working when plugging it as a mass storage. Looking at SCSI option to
get a phone behaving correctly was convoluted to say the least. There
are quite a few other reports about USB card readers needing this option
as well. This patch improves the help text to make the use of the option
more obvious.
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch fixes the GCC 4.4 warning reported by David Binderman and Sergey
Senozhatsky. The old version was working correctly but was not easy to read.
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
scsi timeout on two or more devices may cause extremely long execution
time for user applications because SDEV_OFFLINE state is changed to
SDEV_RUNNING state during scsi error recovery procedures triggered by
a bus reset or a host reset of scsi LLD, and scsi timeout can happens
on the same devices many times.
This happens because scsi_internal_device_unblock() changes device's
state to SDEV_RUNNING even if a device in other states than SDEV_BLOCK,
while the following two transitions are required in this function.
SDEV_BLOCK -> SDEV_RUNNING
SDEV_CREATED_BLOCK -> SDEV_CREATED
Otherwise, it returns -EINVAL.
Signed-off-by: Takahiro Yasui <tyasui@redhat.com>
[matthew@wil.cx: supplied rewritten base for patch]
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Convert all external users of queue limits to using wrapper functions
instead of poking the request queue variables directly.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Until now we have had a 1:1 mapping between storage device physical
block size and the logical block sized used when addressing the device.
With SATA 4KB drives coming out that will no longer be the case. The
sector size will be 4KB but the logical block size will remain
512-bytes. Hence we need to distinguish between the physical block size
and the logical ditto.
This patch renames hardsect_size to logical_block_size.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix function declarations:
drivers/scsi/fcoe/fcoe.c:1356:28: warning: non-ANSI function declaration of function 'fcoe_dev_setup'
drivers/scsi/libfc/fc_rport.c:1293:20: warning: non-ANSI function declaration of function 'fc_setup_rport'
drivers/scsi/libfc/fc_rport.c:1302:23: warning: non-ANSI function declaration of function 'fc_destroy_rport'
[jejb: fixed wrong doc in comment noticed during inspection]
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Marking the ipr clean up function ipr_remove() as __devexit and using
__devexit_p() macro in its address reference.
Signed-off-by: Kleber Sacilotto de Souza <kleber@linux.vnet.ibm.com>
Reported-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
During device discovery read capacity fails with 0x020401 and sets the
device size to 0. As a reason any I/O submitted to this path gets
killed at sd_prep_fn with BLKPREP_KILL. This patch is to retry for
0x020401. NEED_RETRY in scsi_decide_disposition does not give
sufficient time for the device to become ready.
Signed-off-by: Vijay Chauhan <vijay.chauhan@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Make the sym53c8xx_2 driver slave_alloc/destroy less unsafe. References
to the destroyed LCB are cleared from the target structure (instead of
leaving a dangling pointer), and when the last LCB for the target is
destroyed the reference to the upper layer target data is cleared. The
host lock is used to prevent a race with the interrupt handler. Also
user commands are prevented for targets with all LCBs destroyed.
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Tested-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
(Resent with proper formatting)
Fix for the sym53c8xx_2 driver to initialize lun's to_clear flag after
a bus reset (a failed clear can trigger a bus reset and it should not
be attemped again after that).
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Tested-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The driver now waits for the scsi commands associated with a
particular error recovery step to be returned to the mid-layer,
and returns the appropriate SUCCESS or FAILED status. Removes
unneeded polling of chip for interrupts.
This patch also bumps the driver version number.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Remove some unneeded, inactive and unused code, make some trivial
corrections to comments and a printk, and return a proper status
in qla1280_queuecommand. No fundamental logic changes are made.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch (as1224) changes the default timeout for INQUIRY commands
from 3 seconds to 20 seconds, which is the value used by Windows for
USB Mass-Storage devices. Some of these devices, like the Corsair
Flash Voyager (see Bugzilla #12188) really do need a long timeout.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This version contains following main changes
- Switch to new layout to support more types of ASIC.
- SSP TMF supported and related Error Handing enhanced.
- Support flash feature with delay 2*HZ when PHY changed.
- Support Marvell 94xx series ASIC for 6G SAS/SATA, which has 2
88SE64xx chips but any different register description.
- Support SPI flash for HBA-related configuration info.
- Other patch enhanced from kernel side such as increasing PHY type
[jejb: fold back in DMA_BIT_MASK changes]
Signed-off-by: Ying Chu <jasonchu@marvell.com>
Signed-off-by: Andy Yan <ayan@marvell.com>
Signed-off-by: Ke Wei <kewei@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Split mvsas driver into multiple source codes, based on the split
and function distribution found in Marvell's mvsas update.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Zero functional changes, just file movement.
This commit prepares for the upcoming integration of the
Marvell-provided driver update that splits the driver into support
for both 64xx and 94xx chip families.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Read adapter's physical port number from interrupt pin register
and use it instead of pci function number to offset into the
nvram to obtain the port's configuration parameters.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As it may be useful during debugging to use a specific firmware
image.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Changing a lun's queue depth (/sys/block/sdX/device/queue_depth)
isn't sticky when the device is connected via a QLogic fibre
channel adapter.
The QLogic qla2xxx fibre channel driver dynamically adjusts a
lun's queue depth. If a user has a specific need to limit the
number of commands issued to a lun (say a tape drive, or a shared
raid where the total commands issued to all luns is limited at
the controller level, for example) and writes a limiting value to
/sys/block/sdXX/device/queue_depth, the qla2xxx driver will
silently and gradually increase the queue depth back to the
driver limit of ql2xmaxqdepth. While reducing this value (module
parameter) or increasing the interval between ramp ups
(ql2xqfullrampup) offers the potential for a work around it would
be better to have the option of just disabling the dynamic
adjustment of queue depth.
This patch implements an "off switch" as a module parameter.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set the conditional plogi option bit whenever logging in the
fabric management server (if it is already logged in, it does not
need an explicit login; an implicit login suffices).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Information present in static table is only valid for pre-ISP25xx
adapters.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
srbs used to maintain a reference to the request queue on which
it was enqueued. This is no longer required as the request queue
pointer is now maintained in the scsi host that issues the srb.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set the module parameter ql2xmultique_tag to 1 to enable this
feature. In this mode, the total number of response queues
created is equal to the number of online cpus. Turning the block
layer's rq_affinity mode on enables requests to be routed to the
proper cpu and at the same time it enables completion of the IO
in a response queue that is affined to the cpu in the request
path.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set the number of request queues to the module paramater
ql2xmaxqueues. Each vport gets a request queue. The QoS value
set to the request queues determines priority control for queued
IOs. If QoS value is not specified, the vports use the default
queue 0.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Cull and export VN_Port MAC address and VLAN_ID information on
supported FCoE ISPs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The short-circuit to skip the non-applicable 'full-login-lip'
process on 81xx ISPs was nested too deeply in the 'bus-reset'
routine, as the code in qla2x00_loop_reset() should skip the
whole enable_lip_full_login process. The original code could
cause device tear-down due to the qla2x00_wait_for_loop_ready()
call taking a large amount of time.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The last request completion cleanup in scsi_lib left an unused
this_count variable in scsi_io_completion().
(It was used before in a code segment that now uses blk_end_request_all())
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Use new blk_make_request() to allocate a request from bio
and avoid using deprecated blk_rq_append_bio().
This patch is dependent on a block layer patch titled:
[BLOCK] New blk_make_request() takes bio returns request
This is the last usage of blk_rq_append_bio in osd, it can now
be un-exported.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
CC: Jeff Garzik <jeff@garzik.org>
CC: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Now that blk_rq_map_kern will append the buffer onto the
request we can use it easily for adding extra segments
(eg. attributes)
This patch is dependent on a block layer patch titled:
[BLOCK] allow blk_rq_map_kern to append to requests
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
In commit c3a4d78c58, while introducing
rq->resid_len, the default value of residue count was changed from
full count to zero. The conversion was done under the assumption that
when a request fails residue count wasn't defined. However, Boaz and
James pointed out that this wasn't true and the residue count should
be preserved for failed requests too.
This patchset restores the original behavior by setting rq->resid_len
to blk_rq_bytes(rq) on request start and restoring explicit clearing
in affected drivers. While at it, take advantage of the fact that
rq->resid_len is set to full count where applicable.
* ide-cd: rq->resid_len cleared on pc success
* mptsas: req->resid_len cleared on success
* sas_expander: rsp/req->resid_len cleared on success
* mpt2sas_transport: req->resid_len cleared on success
* ide-cd, ide-tape, mptsas, sas_host_smp, mpt2sas_transport, ub: take
advantage of initial full count to simplify code
Boaz Harrosh spotted bug in resid_len initialization. Fixed as
suggested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Borislav Petkov <petkovbb@googlemail.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
In Commit
commit 3b8b5c9b1f
Author: Eric Moore <eric.moore@lsi.com>
Date: Tue Apr 21 15:44:27 2009 -0600
[SCSI] mpt2sas : bump driver version to 01.100.02.00
The MPT2SAS_MAJOR_VERSION didn't get bumped from 00 to 01 so
applications will see it incorrectly as 00.100.02.00 driver instead of
01.100.02.00. Fix by making MPT2SAS_MAJOR_VERSION match the major
number in MPT2SAS_DRIVER_VERSION
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If we can find a type NETDEV_HW_ADDR_T_SAN mac address from the
corresponding netdev for a fcoe interface then sets up added the
fc->ctlr.spma flag and stores spma mode address in ctl_src_addr.
In case the spma flag is set then:-
1. Adds spma mode MAC address in ctl_src_addr as secondary
MAC address, the FLOGI for FIP and pre-FIP will go out
using this address.
2. Cleans up stored spma MAC address in ctl_src_addr in
fcoe_netdev_cleanup.
3. Sets up spma bit in fip_flags for FIP solicitations along
with exiting FPMA bit setting.
4. Initialize the FLOGI FIP MAC descriptor to stored spma
MAC address in ctl_src_addr. This is used as proposed
FCoE MAC address from initiator along with both SPMA
and FPMA bit set in FIP solicitation, in response the
switch may grant any FPMA or SPMA mode MAC address to
initiator.
Removes FIP descriptor type checking against ELS type
ELS_FLOGI in fcoe_ctlr_encaps to update a FIP MAC descriptor,
instead now checks against FIP_DT_FLOGI.
I've tested this with available FPMA-only FCoE switch but
since data_src_addr is updated using same old code for
both FPMA and SPMA modes with FIP or pre-FIP links, so added
SPMA mode will work with SPMA-only switch also provided that
switch grants a valid MAC address.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently fcoe_netdev_config adds netdev pkt handler for fcoe pkts,
fcoe_if_create adds netdev pkt handler for fip packets, a secondary
MAC address is added by fcoe_netdev_config and then later cleanup
for these netdev related config/adds is done only during
fcoe_if_destroy and no cleanup done on error during fcoe interface
creation after above netdev config calling in fcoe_if_create.
So this patch adds single func for above mentioned cleanup the
fcoe_netdev_cleanup and then calls this func on either fcoe interface
destroy or exiting from fcoe_if_create due to an error after fcoe/fip
related above netdev config is done.
Moved netdev pkt handler addition code blocks for fip pkts close to
similar code block for foce pkt in fcoe_netdev_config, so that added
fcoe_netdev_cleanup could be called on error from fcoe_netdev_config
to undo these both additions for fcoe/fip pkt handlers. This move
required reference to fcoe_fip_recv in fcoe_netdev_config, so moved
fip related functions fcoe_fip_recv, fcoe_fip_send and
fcoe_update_src_mac above fcoe_netdev_config.
This consolidation will enable spma mode support in next patch to
easily add or delete spma mode mac address beside fixing current
no cleanup issue during error.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following regression that occurred during the
scsi_dma_map()/unmap()
changes when compiling with CONFIG_DMA_API_DEBUG=y :
WARNING: at lib/dma-debug.c:496 check_unmap+0x142/0x542()
Hardware name:
3w-xxxx 0000:02:02.0: DMA-API: device driver tries to free DMA memory
it has not allocated [device address=0x0000000000000000] [size=36
bytes]
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch fixes the following regression the occurred during the
scsi_dma_map()/unmap() changes:
3w-9xxx 0001:45:00.0: DMA-API: device driver tries to free DMA memory
it has not allocated [device address=0x0000000000000000] [size=36
bytes]
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Andrew Vasquez wrote:
> fc-transport: Close state transition-window during rport deletion.
>
> After an rport's state has transitioned to FC_PORTSTATE_BLOCKED,
> but, prior to making the upcall to 'block' the scsi-target
> associated with an rport, queued commands can recycle and
> ultimately run out of retries causing failures to propagate to
> upper-level drivers. Close this transition-window by returning
> the non-'retries' modifying DID_IMM_RETRY status for submitted
> I/Os.
The same can happen for iscsi when transitioning from logged in
to failed and blocking the sdevs.
This patch converts iscsi and fc's transitions back to use DID_IMM_RETRY
instead of DID_TRANSPORT_DISRUPTED which has a limited number of retries
that we do not want to use for handling this race.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
[Addition of iscsi and fc port online devloss case conversion by Mike Christie]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch initializes the max_target_blocked field of a scsi target
structure so that a queuecommand return value of
SCSI_MLQUEUE_TARGET_BUSY will actually result in having the
scsi_queue_insert blocking the device queue before requeuing the
command and running the queue. Otherwise, can and does cause livelock
on single CPU configurations if/when open-iSCSI software initiator's
command PDU window fills.
Signed-off-by: Ed Goggin <egoggin@vmware.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
fnic is a driver for the Cisco PCI-Express FCoE HBA
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Commit c3a4d78c58 introduced
rq->data_len and converted residual count users to it. While
converting, it mistakenly converted scsi_end_request() to finish
requests with residual count when it wants to do is fully complete the
request. Fix it by using blk_end_request_all() instead.
This bug was spotted by Boaz Harrosh.
Signed-off-by: Tejun Heo <tj@kernel.org>
Spotted-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Till now block layer allowed two separate modes of request execution.
A request is always acquired from the request queue via
elv_next_request(). After that, drivers are free to either dequeue it
or process it without dequeueing. Dequeue allows elv_next_request()
to return the next request so that multiple requests can be in flight.
Executing requests without dequeueing has its merits mostly in
allowing drivers for simpler devices which can't do sg to deal with
segments only without considering request boundary. However, the
benefit this brings is dubious and declining while the cost of the API
ambiguity is increasing. Segment based drivers are usually for very
old or limited devices and as converting to dequeueing model isn't
difficult, it doesn't justify the API overhead it puts on block layer
and its more modern users.
Previous patches converted all block low level drivers to dequeueing
model. This patch completes the API transition by...
* renaming elv_next_request() to blk_peek_request()
* renaming blkdev_dequeue_request() to blk_start_request()
* adding blk_fetch_request() which is combination of peek and start
* disallowing completion of queued (not started) requests
* applying new API to all LLDs
Renamings are for consistency and to break out of tree code so that
it's apparent that out of tree drivers need updating.
[ Impact: block request issue API cleanup, no functional change ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: unsik Kim <donari75@gmail.com>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Laurent Vivier <Laurent@lvivier.info>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With the previous changes, the followings are now guaranteed for all
requests in any valid state.
* blk_rq_sectors() == blk_rq_bytes() >> 9
* blk_rq_cur_sectors() == blk_rq_cur_bytes() >> 9
Clean up accessor usages. Notable changes are
* nbd,i2o_block: end_all used instead of explicit byte count
* scsi_lib: unnecessary conditional on request type removed
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With recent unification of fields, it's now guaranteed that
rq->data_len always equals blk_rq_bytes(). Convert all non-IDE direct
users to accessors. IDE will be converted in a separate patch.
Boaz: spotted incorrect data_len/resid_len conversion in osd.
[ Impact: convert direct rq->data_len usages to blk_rq_bytes() ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With recent cleanups, there is no place where low level driver
directly manipulates request fields. This means that the 'hard'
request fields always equal the !hard fields. Convert all
rq->sectors, nr_sectors and current_nr_sectors references to
accessors.
While at it, drop superflous blk_rq_pos() < 0 test in swim.c.
[ Impact: use pos and nr_sectors accessors ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Dario Ballabio <ballabio_dario@emc.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: unsik Kim <donari75@gmail.com>
Cc: Laurent Vivier <Laurent@lvivier.info>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Implement accessors - blk_rq_pos(), blk_rq_sectors() and
blk_rq_cur_sectors() which return rq->hard_sector, rq->hard_nr_sectors
and rq->hard_cur_sectors respectively and convert direct references of
the said fields to the accessors.
This is in preparation of request data length handling cleanup.
Geert : suggested adding const to struct request * parameter to accessors
Sergei : spotted error in patch description
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Ackec-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
rq->data_len served two purposes - the length of data buffer on issue
and the residual count on completion. This duality creates some
headaches.
First of all, block layer and low level drivers can't really determine
what rq->data_len contains while a request is executing. It could be
the total request length or it coulde be anything else one of the
lower layers is using to keep track of residual count. This
complicates things because blk_rq_bytes() and thus
[__]blk_end_request_all() relies on rq->data_len for PC commands.
Drivers which want to report residual count should first cache the
total request length, update rq->data_len and then complete the
request with the cached data length.
Secondly, it makes requests default to reporting full residual count,
ie. reporting that no data transfer occurred. The residual count is
an exception not the norm; however, the driver should clear
rq->data_len to zero to signify the normal cases while leaving it
alone means no data transfer occurred at all. This reverse default
behavior complicates code unnecessarily and renders block PC on some
drivers (ide-tape/floppy) unuseable.
This patch adds rq->resid_len which is used only for residual count.
While at it, remove now unnecessasry blk_rq_bytes() caching in
ide_pc_intr() as rq->data_len is not changed anymore.
Boaz : spotted missing conversion in osd
Sergei : spotted too early conversion to blk_rq_bytes() in ide-tape
[ Impact: cleanup residual count handling, report 0 resid by default ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Merge reason: tracing/core was on a .30-rc1 base and was missing out on
on a handful of tracing fixes present in .30-rc5-almost.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that all block request data transfer is done via bio, rq->data
isn't used. Kill it.
While at it, make the roles of rq->special and buffer clear.
[ Impact: drop now unncessary field from struct request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Boaz Harrosh <bharrosh@panasas.com>
There are many [__]blk_end_request() call sites which call it with
full request length and expect full completion. Many of them ensure
that the request actually completes by doing BUG_ON() the return
value, which is awkward and error-prone.
This patch adds [__]blk_end_request_all() which takes @rq and @error
and fully completes the request. BUG_ON() is added to to ensure that
this actually happens.
Most conversions are simple but there are a few noteworthy ones.
* cdrom/viocd: viocd_end_request() replaced with direct calls to
__blk_end_request_all().
* s390/block/dasd: dasd_end_request() replaced with direct calls to
__blk_end_request_all().
* s390/char/tape_block: tapeblock_end_request() replaced with direct
calls to blk_end_request_all().
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
OSC's OSD2 target: [git clone git://git.open-osd.org/osc-osd/ master]
(Initiator code prior to this patch must use: "git checkout CDB_VER_OSD2r01"
in the target tree above)
This is a summery of the wire changes:
* OSDv2_ADDITIONAL_CDB_LENGTH == 192 => 228 (Total CDB is now 236 bytes)
* Attributes List Element Header grew, so attribute values are 8 bytes
aligned.
* Cryptographic keys and signatures are 20 => 32
* Few new definitions.
(Still missing new standard definitions attribute values, these do not change
wire format and will be added later when needed)
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In OSD2r04 draft, cryptographic key size changed to 32 bytes from
OSD1's 20 bytes. This causes a couple of on-the-wire structures
to change, including the CDB.
In this patch the OSD1/OSD2 handling is separated out in regard
to affected structures, but on-the-wire is still the same. All
on the wire changes will be submitted in one patch for bisect-ability.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In OSD2r05 draft each attribute list element header was changed
so attribute-value would be 8 bytes aligned. In OSD2r01-r04
it was aligned on 2 bytes. (This is because in OSD2r01 the complete
element was 8 bytes padded at end but the header was not adjusted
and caused permanent miss-alignment.)
OSD1 elements are not padded and might be or might not be aligned.
OSD1 is still supported.
In this code we do all the code re-factoring to separate OSD1/OSD2
differences but do not change actual wire format. All wire format
changes will happen in one patch later, for bisect-ability.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bio_map_kern() returns an ERR_PTR() not NULL.
Found by smatch (http://repo.or.cz/w/smatch.git). Compile tested.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Here's a fix for hotplug events. The useage of queue_delayed_work seems
to broke the fifo for processing of firmware events. After several iterations
of adding and removing cabling connected to jbods, the devices are not
getting added becuase kernel thread is activited out of order.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Diagnostic buffer support is already there in the driver. This support allows
applications to pull ring buffers from controller firmware for debugging
firmware related issues.
What this patch does is sends reqeust to firmware to release the buffers prior
to host reset. This will allow what ever debug info is there prior to reset
to be dma'd to host memory. With out this fix, some of the debug data would
been lost.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Bug fix in the broadcast primative async event code where the driver would
stop sending tm queries after the first queury was completed. This was due
driver not reseting the tm_cmds.status field back to MPT2_CMD_NOT_USED after
completing a task management request.
An addtional fix adding sanity check to insure sas_device->starget set to NULL.
During multipath testing fail over/fail back, the mid layer was holding onto
sdev longer than the fail back period, thus starget was getting set to NULL
for device being added.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The Dell branding along with the VID, DID, SSVID, SSDID following the LSI
branding that contains the card firmware/chip/bios versions. If the SSDID
is not known but it is a Dell HBA, the driver will print the SSDID instead
of the Dell branding string. Nothing will be printed for non Dell HBAs
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The driver name needs to be at the beginining of the driver_version string in
MPT2IOCINFO ioctl. This is the same behaviour is there already in the mptsas
driver.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The driver is not freeing message frame when returning failure from
_ctl_do_task_abort. If you call this function 500 times when its unable
to find an active task mid, you end up with no message frames.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There is a bug in firmware where the reply message frame says there is a
16kb sense buffer, when in reality its only 20 bytes. This fix insures
the memcpy action doesn't corrupte the memory beyond the 90 bytes allocated in
the scsi command for sense buffer.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The poison sanity check on the reply_post_free register needs to be by 32bit,
not 64bit. The poison check is there because its possible that the driver read
the 1st 32bit before the 2nd 32bit has been written to by firmware. In other
words, this handles race between driver reading the 64 bit register, and it
being dma'd across pci memory from controller firmware as two 32bit pci writes.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The current magic number is shared with mptsas driver. This to be unique to
fix issues with register_ioctls32_conversion in older kernels. We are making
this change across all versions of the sas2.0 drivers.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Shifting an unsigned char implicitly casts it to a signed int. This
caused 'lba' to sign-extend and Linux would then try READ CAPACITY 16
which was not supported by at least one drive. Using the
get_unaligned_be*() helpers keeps us from having to worry about how the
extension might occur.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ata_sas_slave_configure was changed such that it now allocates
some memory for a drain buffer for ATAPI devices. Fixup the ipr
driver such that we no longer make this call with interrupts disabled.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The FCoE forwarder (FCF) would be selected, but then would soon time
out after three advertisements were missed. This would be 24 seconds
by default, or 3 times the keep-alive interval configured on the switch.
The cause was that the multicast address for all FIP E-nodes
was never added.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When building with a .config generated from 'make allmodconfig'
some build warnings are generated. This patch corrects the warnings,
adds a FC_FID_NONE (= 0) enumeration for FC-IDs and cleans up one
variable naming to meet our variable naming conventions. For example,
fc_lport's should be named "lport," not "lp."
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
These probably never should have been exported.
If they were needed outside of the fcoe module, they
would have been moved to libfcoe.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
sk_buff pointers should use kfree_skb() instead of vanilla kfree().
Found by smatch (http://repo.or.cz/w/smatch.git).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When a delete event is queued for an rport, set state to NONE so that no
other processing is done on the rport as it is being removed.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
After lport_destroy, the local port should not be used again. Transition
to state NONE, any incoming frames or link up should not transition out
of this state since we are deleting exchange table and cleaning up the
local port. Also, mark link as down.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We want to generate the rport queue event (from the logoff)
before flushing the queue otherwise the event may still be
in the queue when we logoff.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Rogue ports are currently not tracked on any list. The only reference
to them is through any outstanding exchanges pending on the rogue ports.
If the module is removed while a retry is set on a rogue port
(say a Plogi retry for instance), this retry is not cancelled because there
is no reference to the rogue port in the discovery rports list. Thus the
local port can clean itself up, delete the exchange pool, and then the
rogue port timeout can fire and try to start up another exchange.
This patch tracks the rogue ports in a new list disc->rogue_rports. Creating
a new list instead of using the disc->rports list keeps remote port code
change to a minimum.
1) Whenever a rogue port is created, it is immediately added to the
disc->rogue_rports list.
2) When the rogues port goes to ready, it is removed from the rogue list
and the real remote port is added to the disc->rports list
3) The removal of the rogue from the disc->rogue_rports list is done in
the context of the fc_rport_work() workQ thread in discovery callback.
4) Real rports are removed from the disc->rports list like before. Lookup
is done only in the real rports list. This avoids making large changes
to the remote port code.
5) In fc_disc_stop_rports, the rogues list is traversed in addition to the
real list to stop the rogue ports and issue logoffs on them. This way, rogue
ports get cleaned up when the local port goes away.
6) rogue remote ports are not removed from the list right away, but
removed late in fc_rport_work() context, multiple threads can find the same
remote port in the list and call rport_logoff(). Rport_logoff() only
continues with the logoff if port is not in NONE state, thus preventing
multiple logoffs and multiple list deletions.
7) Since the rport is removed from the disc list at a later stage
(in the disc callback), incoming frames can find the rport even if
rport_logoff() has been called on the rport. When rport_logoff() is called,
the rport state is set to NONE, and we are trying to cancel all exchanges
and retries on that port. While in this state, if an incoming
Plogi/Prli/Logo or other frames match the rport, we should not reply
because the rport is in the NONE state. Just drop the frame, since the
rport will be deleted soon in the disc callback (fc_rport_work)
8) In fc_disc_single(), remove rport lookup and call to fc_disc_del_target.
fc_disc_single() is called from recv_rscn_req() where rport lookup
and rport_logoff is already done.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For instance, if there is a Plogi pending (remote port is in Plogi state),
and the state changes to say NONE (because the port is being logged off),
then when the Plogi resp times out, do not start a retry.
This patch partially reverts an earlier patch (libfc: check for err when
recv and state is incorrect), by moving the state check back to before
checking for error. However, if the state does not match, then there is
an additional check to see if its an error ptr or a real frame before
jumping to err or out respectively.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
gpn_ft_resp processing currently does not hold the discovery lock.
disc_done() thus gets called from gpn_ft_resp or from gpn_ft_parse
without the lock held. This then sets disc->pending to zero or calls
gpn_ft_req() without disc_lock held.
- Hold disc mutex during gpn_ft resp processing
- In disc_done, release the disc mutex while calling lport callback
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
(version 2)
Fixed a bug in calculating ddp map range when search for free entries:
it was going beyond the end by one, thus corrupting gl_skb[0].
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When doing a lot (128) of large writes (256K) we can hit the cxgb3_snd_win
check pretty easily. The driver's xmit thread then takes 100% of the cpu.
The driver should not be returning -EAGAIN for this problem. It should
be returing -ENOBUFS, then when the window is opened again it should
queue the xmit thread (it already wakes the xmit thread).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
cxgb3i was setting can_queue to only 128 commands, and was
setting the can_queue and cmd_per_lun to the same value.
This sets the can_queue to 1024 commands, and sets the cmd_per_lun
to a safer default of 32.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set target can queue limit to the number of preallocated
session tasks we have.
This along with the cxgb3i can_queue patch will fix a throughput
problem where it could only queue one LU worth of data at a time.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If a command's scsi cmd pdu setup fails then we can just fail
the IO to the scsi layer. If a DATA_OUT for a R2T fails then
we will want to drop the session, because it means we got a
bad request from the target (iscsi protocol error).
This patch has us propogate the error upwards so libiscsi_tcp
or libiscsi can decide what the best action is to take. It
also fixes a bug where we could try to grab the session lock
while holding it, because if iscsi_tcp drops the session in the
pdu setup callout the session lock is held when setting up the
scsi cmd pdu.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We cannot call blk_plug_device from scsi_target_queue_ready
because the q lock is not held. And we do not need to call
it from there because when we return 0, the scsi_request_fn
not_ready handling will plug the queue for us if needed.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update driver version to 8.3.1
Also update copyright end year for driver.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
8.3.1 Fixes/Changes :
- Fix incorrect byte-swapping on word 4 of IOCB (data length) which
caused LUNs to not be discovered on big-endian (e.g. PPC)
- Remove a bad cast of MBslimaddr which loses the __iomem (sparse)
- Make lpfc_debugfs_mask_disc_trc static (sparse)
- Correct misspelled word BlockGuard in lpfc_logmsg.h comment
- Replaced repeated code segment for canceling IOCBs from a list with
a function call, lpfc_sli_cancel_iocbs().
- Increased HBQ buffers to support 40KB SSC sequences.
- Added sysfs interface to update speed and topology parameter without
link bounce.
- Fixed bug with sysfs fc_host WWNs not being updated after changing
the WWNs.
- Check if the active mailbox is NULL in the beginning of the mailbox
timeout handler - fixes panic in the mailbox timeout handler while
running IO stress test
- Fixed system panic in lpfc_pci_remove_one() due to ndlp indirect
reference to phba through vport
- Removed de-reference of scsi device after call to scsi_done() to fix
panic in scsi completion path while accessing scsi device after
scsi_done is called.
- Fixed "Nodelist not empty" message when unloading the driver after
target reboot test
- Added LP2105 HBA model description
- Added code to print all 16 words of unrecognized ASYNC events
- Fixed memory leak in vport create + delete loop
- Added support for handling dual error bit from HBA
- Fixed a driver NULL pointer dereference in lpfc_sli_process_sol_iocb
- Fixed a discovery bug with FC switch reboot in lpfc_setup_disc_node
- Take NULL termintator into account when calculating available buffer space
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
blk_rq_unmap_user() returns EFAULT if a program passes an invalid
address to kernel (the kernel fails to copy data to user space). sg
needs to pass the returned value to user space instead of ignoring
it. Before the block layer conversion, sg returns EFAULT
properly. This restores the old behavior.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
So, what's happening here is that the drive is reporting a sense of
2/4/1 ("logical unit is becoming ready") from sr_test_unit_ready(), and
then we ask for the media event notification before checking that result
at all. The check_media_event_descriptor() call isn't getting a check
condition, but it's also reporting that the tray is closed and that
there's no media. In actuality it doesn't yet know if there's media or
not, but there's no way to express that in the media event status field.
My current thought is that if it told us the device isn't yet ready, we
should return that immediately, since there's nothing that'll tell us
any more data than that reliably:
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
commit 7a192ec334 ("platform driver: fix
incorrect use of 'platform_bus_type' with 'struct device_driver') turned a
driver_UNregister into platform_driver_REGISTER. Correct this to
platform_driver_UNregister.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
There is currently only one way for userspace to say "wait for my storage
device to get ready for the modules I just loaded": to load the
scsi_wait_scan module. Expectations of userspace are that once this
module is loaded, all the (storage) devices for which the drivers
were loaded before the module load are present.
Now, there are some issues with the implementation, and the async
stuff got caught in the middle of this: The existing code only
waits for the scsy async probing to finish, but it did not take
into account at all that probing might not have begun yet.
(Russell ran into this problem on his computer and the fix works for him)
This patch fixes this more thoroughly than the previous "fix", which
had some bad side effects (namely, for kernel code that wanted to wait for
the scsi scan it would also do an async sync, which would deadlock if you did
it from async context already.. there's a report about that on lkml):
The patch makes the module first wait for all device driver probes, and then it
will wait for the scsi parallel scan to finish.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Though one can specify '-d /dev/sda1' when using blktrace, it still
traces the whole sda.
To support per-partition tracing, when we start tracing, we initialize
bt->start_lba and bt->end_lba to the start and end sector of that
partition.
Note some actions are per device, thus we don't filter 0-sector events.
The original patch and discussion can be found here:
http://marc.info/?l=linux-btrace&m=122949374214540&w=2
Signed-off-by: Shawn Du <duyuyang@gmail.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
LKML-Reference: <49E42620.4050701@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix lpfc_parse_bg_err()'s use of do_div(). It should be passing a 64-bit
variable as the first parameter. However, since it's only using a 32-bit
variable, it doesn't need to use do_div() at all, but can instead use the
division operator.
This deals with the following warnings:
CC drivers/scsi/lpfc/lpfc_scsi.o
drivers/scsi/lpfc/lpfc_scsi.c: In function 'lpfc_parse_bg_err':
drivers/scsi/lpfc/lpfc_scsi.c:1397: warning: comparison of distinct pointer types lacks a cast
drivers/scsi/lpfc/lpfc_scsi.c:1397: warning: right shift count >= width of type
drivers/scsi/lpfc/lpfc_scsi.c:1397: warning: passing argument 1 of '__div64_32' from incompatible pointer type
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the second go through of the old DMA_nBIT_MASK macro,and there're not
so many of them left,so I put them into one patch.I hope this is the last round.
After this the definition of the old DMA_nBIT_MASK macro could be removed.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Greg KH <greg@kroah.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a race between resume from hibernation and the asynchronous
scanning of SCSI devices and to prevent it from happening we need to
call scsi_complete_async_scans() during resume from hibernation.
In addition, if the resume from hibernation is userland-driven, it's
better to wait for all device probes in the kernel to complete before
attempting to open the resume device.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We were calculating the wrong address for the start of the data.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Tested-by: Jeremy Higdon <jeremy@sgi.com>
Replace all DMA_31BIT_MASK macro with DMA_BIT_MASK(31)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_39BIT_MASK macro with DMA_BIT_MASK(39)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_40BIT_MASK macro with DMA_BIT_MASK(40)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
sg_rq_end_io() is called via rq->end_io. In some rare cases,
sg_rq_end_io calls blk_put_request/blk_rq_unmap_user (when a program
issuing a command has gone before the command completion; e.g. by
interrupting a program issuing a command before the command
completes).
We can't call blk_put_request/blk_rq_unmap_user in interrupt so the
commit c96952ed70 uses
execute_in_process_context().
The problem is that scsi_error_handler() calls rq->end_io too. We
can't call blk_put_request/blk_rq_unmap_user too in this path (we hold
q->queue_lock).
To avoid the above problem, in these rare cases, this patch always
uses schedule_work() instead of execute_in_process_context().
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
a2091_{detect,release}() can become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
a3000_{detect,release}() can become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- needs to use copy_from_user for iovec before passing it to
blk_rq_map_user_iov().
- before the block layer conversion, if ->dxfer_len and sum of iovec
disagrees, the shorter one wins. However, currently sg returns
-EINVAL. This restores the old behavior.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Firmware blob is little endian
Thanks to Stephen Rothwell for fixing typos
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Firmware blob is little endian looks like this...
unsigned char Version1
unsigned char Version2
unsigned char Version3
unsigned char Padding
unsigned short start_address
unsigned short data
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Le lundi 30 mars 2009, Chris Wright a écrit :
> q->queue could be ERR_PTR(-ENOMEM) which will break unwinding
> on error. Make iscsi_pool_free more defensive.
>
Making the freeing of q->queue dependent on q->pool being set looks
really weird (although it is correct at the moment. But this seems
to be fixable in a much simpler way.
With the benefit that only the error case is slowed down. In both
cases we have a problem if q->queue contains an error value but it's
not -ENOMEM. Apparently this can't happen today, but it doesn't feel
right to assume this will always be true. Maybe it's the right time
to fix this as well.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
cxgb3i_ddp_cleanup just calls ddp_release directly so there is
no reason for the wrapper. This patch just renames ddp_release
to cxgb3i_ddp_cleanup and removes the old wrapper function.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Merge cxgb3i_ddp.ko to cxgb3i.ko as there is no other users.
- Bump the driver version up to 1.0.2.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Keep track of offloaded tcp connections per adapter. Close all of the
connections upon reset.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Orignally from Karen Xie, but merge conflicts/errors fixed up by
Mike Christie.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Re-initialize the ddp settings after chip reset. It includes re-initialize
the related registers and the ddp map.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add error notification handling function which is called during chip reset.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
changes:
- set aac_cache=2 as default value to avoid performance problem
(Novell bugzilla #469922)
- Dell/PERC controller boot problem fixed (RedHat bugzilla #457552)
- WWN flag added to fix SLES10 SP1/SP2 drive detection problems
- 64-bit support changes
- DECLARE_PCI_DEVICE_TABLE macro added
- controller type changes
Signed-off-by: Achim Leubner <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mention ATAPI. We could insert an essay about libata and ide-scsi etc but
the failure case is someone enables it which is just fine so keep it
simple.
(Revised text from suggestion by Matthew Wilcox)
Closes#7736
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This adds the support of a new SAS 6G controller (st_yel)
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Use config struct (st_card_info) for parameters of different controllers
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This adds the MSI support (default 0=off)
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
These are some small code fixes and changes, including:
- use 64 bit when possible
- remove some unnecessary code (in interrupt, queuecommand routine etc.)
- code change for reset handler
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
FIP is the new standard way to discover Fibre-Channel Forwarders (FCFs)
by sending solicitations and listening for advertisements from FCFs.
It also provides for keep-alives and period advertisements so that both
parties know they have connectivity. If the FCF loses connectivity to
the storage fabric, it can send a Link Reset to inform the E_node.
This version is also compatible with pre-FIP implementations, so no
configured selection between FIP mode and non-FIP mode is required.
We wait a couple seconds after sending the initial solicitation
and then send an old-style FLOGI. If we receive any FIP frames,
we use FIP only mode. If the old FLOGI receives a response,
we disable FIP mode. After every reset or link up, this
determination is repeated.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The foce_softc mem was reserved by libfc_host_alloc as well as
by fcoe_host_alloc.
Removes one liner fcoe_host_alloc completely, instead directly calls
libfc_host_alloc to alloc scsi_host with libfc for just one fcoe_softc
as fcoe private data.
Moves libfc_host_alloc to libfc.h since it is a libfc API, placed
lport_priv API adjacent to libfc_host_alloc since this is related
to scsi_host priv data.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Removes no where used several inline functions prefixed with skb_*
and be16_to_cpu.
Moves fcoe module specific func prototypes to fcoe.c from libfcoe.h,
moved only need for build.
Adds fcoe module header file fcoe.h and then moves fcoe module
specific fcoe_percpu_s and fcoe_softc to fcoe.h from libfcoe.h.
Moves all defines from fcoe.c to fcoe.h since now fcoe module
has its own header file fcoe.h.
[jejb: removed EXPORT_SYMBOL_GPL(fcoe_fc_crc) which caused a section mismatch]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Moves these functions as-is from fcoe.c to libfcoe.c, since
they're are common routines:
- fcoe_wwn_from_mac
- fcoe_libfc_config
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Just sets up build environment for libfcoe module towards a
libfcoe library for libfc LLDs using FCoE as libfc transport.
Common library code to libfcoe is added in next patch.
Also, updated MODULE_LICENSE from "GPL" string to "GPL v2" for
libfc, libfcoe and fcoe modules to accurately match the licenses.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Renames libfcoe.c to fcoe.c, fcoe.c becomes the only
.c file for fcoe.ko.
Also deleted "$Id: Makefile" from fcoe module Makefle.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Moves only required code from fcoe_sw.c to libfcoe.c towards having
just one source file for fcoe module, this gets rid off default sw
transport code in a separate fcoe_sw.c file.
Very minor renaming along this move, dropped _sw_ or _SW_ use
in names and replaced them by _if_ as a auxiliary interface
functions. Now some of these funcs can be removed or merged with
other func after fcoe transport is gone, but that should be
in another patch to keep this patch simple.
Now the libfcoe.c file name for fcoe module doesn't go along well,
so the libfcoe.c file renaming to fcoe.c as the only single fcoe
module file is done in next patch to keep this patch clean
and small for review.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The fcoe transport code was added for generic FCoE transport
infrastructure to allow additional offload related module loading
on demand, this is not required anymore after recently added
different offload approach by having offload related func ops
in netdev.
This patch removes fcoe transport related code use, calls functions
directly between existing libfcoe.c and fcoe_sw.c for now, for
example fcoe_sw_destroy and fcoe_sw_create calling.
The fcoe_sw.c and libfcoe.c code will be further consolidated in
later patches and then also the default fcoe sw transport code
file fcoe_sw.c will be completely removed.
The fcoe transport code files are completely removed in next
patch to keep this patch simple for reviewing.
[This patch is an update to a previous patch. This update
resolves a build error as well as fixes a defect related to
not calling fc_release_transport().]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds support for dynamically created Rx threads
upon CPU hotplug events.
There were existing synchronization problems that this patch
attempts to resolve. The main problem had to do with fcoe_rcv()
running in a different context than the hotplug notifications.
This opened the possiblity that fcoe_rcv() would target a Rx
thread for a skb. However, that thread could become NULL if
the CPU was made offline.
This patch uses the Rx queue's (a skb_queue) lock to protect
the thread it's associated with and we use the 'thread' member
of the fcoe_percpu_s to determine if the thread is ready to
accept new skbs.
The patch also attempts to do a better job of cleaning up, both
if hotplug registration fails as well as when the module is
removed.
Contribution provided by Joe Eykholt <jeykholt@cisco.com> to
fix incorrect use of __cpuinitdata.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Remove the hotplug creation of dev_stats, we allocate for all possible CPUs
now when we allocate the lport.
v2: Durring the 2.6.30 merge window, before these patches were comitted,
'percpu_ptr' was renamed 'per_cpu_ptr'. This latest update updates this
patch for the name change.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Convert fcoe_percpu array to use the per-cpu variables
that the kernel provides. Use the kernel's functions to
access this structure.
The cpu member of the fcoe_percpu_s is no longer needed,
so this patch removes it too.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently the skb_queue is initialized every time the associated
CPU goes online. This patch has libfcoe initializing the skb_queue
for all possible CPUs when the module is loaded.
This patch also re-orders some declarations in the fcoe_rcv()
function so the structure declarations are grouped before
the primitive declarations.
Lastly, this patch converts all CPU indicies to use unsigned int
since CPU indicies should not be negative.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Remove the creation of the symlink from the device to
it's class. On modern systems this is already created by
a udev rule and would WARN on load. On old systems it is
not needed, none of the current osd user-mode tools use
this link.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
A fix for a very serious and stupid bug in osd_initiator. It
used to call blk_put_request() regardless of if it was from
the end_io callback or if called after a sync execution.
It should call the unlocked version __blk_put_request() instead.
Also fixed is the remove of _abort_unexecuted_bios hack, and use of
blk_end_request(,-ERROR,) to deallocate half baked requests. I've
audited the code and it should be safe.
Reported and
Tested-by: Xu Yang <onlyxuyang@qq.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We have a problem with recovered error handling in that any command
which goes down as BLOCK_PC but which returns a sense code of RECOVERED
ERROR gets completed with -EIO. For actual SG_IO commands, this doesn't
matter at all, since the error return code gets dropped in favour of
req->errors which contain the SCSI completion code.
However, if this command is part of the block system, then it will pay
attention to the returned error code. In particularly if a SYNCHRONIZE
CACHE from a barrier command completes with RECOVERED ERROR, the
resulting -EIO on the barrier causes block to error the request and
return it to the filesystem. Fix this by converting the -EIO for
recovered error to zero, plus remove the printing of this from sd and sr
so the message isn't double printed.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
aic79xx leaves timers inserted when ahd_init() (which inserts
two timers at its very end) succeeds but ahd_pci_map_int()
fails. In this case ahd->init_level gets incremented to 5 only
when that function succeeds, but ahd_free() calls ahd_shutdown()
only when ahd->init_level == 5, and ahd_shutdown() is where the
timers get removed. Since the freeing of the IRQ is not controlled
by ahd->init_level, we should increment init_level prior to
calling ahd_pci_map_int().
Reported-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
