dev_set_net is called for
- just allocated devices
- devices moving from one namespace to another
release_net has proper check inside to distinguish these cases.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently vlan group is searched using one key - the ifindex.
We'll have to lookup the vlan_group by two keys - ifindex and
net. Turning the vlan_group lookup key to struct net_device
pointer will make this process easier.
Besides, this will eliminate one more place in the networking,
that assumes that indexes are unique in the kernel.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch remove the usage of a nonexisting kconfig variable.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert P. J. Day spotted that my removal of the Sangoma drivers missed
a few bits.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the ebtables nflog watcher to the kernel in order to
allow ebtables log through the nfnetlink_log backend.
Signed-off-by: Peter Warasin <peter@endian.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Connection tracking helpers (specifically FTP) need to be called
before NAT sequence numbers adjustments are performed to be able
to compare them against previously seen ones. We've introduced
two new hooks around 2.6.11 to maintain this ordering when NAT
modules were changed to get called from conntrack helpers directly.
The cost of netfilter hooks is quite high and sequence number
adjustments are only rarely needed however. Add a RCU-protected
sequence number adjustment function pointer and call it from
IPv4 conntrack after calling the helper.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Move the UDP-Lite conntrack checksum validation to a generic helper
similar to nf_checksum() and make it fall back to nf_checksum()
in case the full packet is to be checksummed and hardware checksums
are available. This is to be used by DCCP conntrack, which also
needs to verify partial checksums.
Signed-off-by: Patrick McHardy <kaber@trash.net>
The use of xt_sctp.h flagged up -Wshadow warnings in userspace, which
prompted me to look at it and clean it up. Basic operations have been
directly replaced by library calls (memcpy, memset is both available
in the kernel and userspace, and usually faster than a self-made
loop). The is_set and is_clear functions now use a processing time
shortcut, too.
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Commit 9335f047fe aka
"[NETFILTER]: ip_tables: per-netns FILTER, MANGLE, RAW"
added per-netns _view_ of iptables rules. They were shown to user, but
ignored by filtering code. Now that it's possible to at least ping loopback,
per-netns tables can affect filtering decisions.
netns is taken in case of
PRE_ROUTING, LOCAL_IN -- from in device,
POST_ROUTING, LOCAL_OUT -- from out device,
FORWARD -- from in device which should be equal to out device's netns.
This code is relatively new, so BUG_ON was plugged.
Wrappers were added to a) keep code the same from CONFIG_NET_NS=n users
(overwhelming majority), b) consolidate code in one place -- similar
changes will be done in ipv6 and arp netfilter code.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This expresses __skb_queue_tail() in terms of __skb_insert(),
using __skb_insert_before() as auxiliary function.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This expresses __skb_append in terms of __skb_queue_after, exploiting that
__skb_append(old, new, list) = __skb_queue_after(list, old, new).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
By reordering, __skb_queue_after() is expressed in terms of __skb_insert().
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
By rearranging the order of declarations, __skb_dequeue() is expressed in terms of
* skb_peek() and
* __skb_unlink(),
thus in effect mirroring the analogue implementation of __skb_dequeue_tail().
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct ipv6_opt_hdr is the common structure for IPv6 extension
headers, and it is common to increment the pointer to get
the real content. On the other hand, since the structure
consists only of 1-byte next-header field and 1-byte length
field, size of that structure depends on architecture; 2 or 4.
Add "packed" attribute to get 2.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since NETDEV_REGISTER notifier chain is responsible for creating
inet6_dev{}, we do not need to call ipv6_find_idev() directly here.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xfrm_get_policy() and xfrm_add_pol_expire() put some rather large structs
on the stack to work around the LSM API. This patch attempts to fix that
problem by changing the LSM API to require only the relevant "security"
pointers instead of the entire SPD entry; we do this for all of the
security_xfrm_policy*() functions to keep things consistent.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no reason for this to be in the header, and it just hurts
recompile time.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Max Krasnyanskiy <maxk@qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SKF_ADF_NLATTR searches for a netlink attribute, which avoids manually
parsing and walking attributes. It takes the offset at which to start
searching in the 'A' register and the attribute type in the 'X' register
and returns the offset in the 'A' register. When the attribute is not
found it returns zero.
A top-level attribute can be located using a filter like this
(example for nfnetlink, using struct nfgenmsg):
...
{
/* A = offset of first attribute */
.code = BPF_LD | BPF_IMM,
.k = sizeof(struct nlmsghdr) + sizeof(struct nfgenmsg)
},
{
/* X = CTA_PROTOINFO */
.code = BPF_LDX | BPF_IMM,
.k = CTA_PROTOINFO,
},
{
/* A = netlink attribute offset */
.code = BPF_LD | BPF_B | BPF_ABS,
.k = SKF_AD_OFF + SKF_AD_NLATTR
},
{
/* Exit if not found */
.code = BPF_JMP | BPF_JEQ | BPF_K,
.k = 0,
.jt = <error>
},
...
A nested attribute below the CTA_PROTOINFO attribute would then
be parsed like this:
...
{
/* A += sizeof(struct nlattr) */
.code = BPF_ALU | BPF_ADD | BPF_K,
.k = sizeof(struct nlattr),
},
{
/* X = CTA_PROTOINFO_TCP */
.code = BPF_LDX | BPF_IMM,
.k = CTA_PROTOINFO_TCP,
},
{
/* A = netlink attribute offset */
.code = BPF_LD | BPF_B | BPF_ABS,
.k = SKF_AD_OFF + SKF_AD_NLATTR
},
...
The data of an attribute can be loaded into 'A' like this:
...
{
/* X = A (attribute offset) */
.code = BPF_MISC | BPF_TAX,
},
{
/* A = skb->data[X + k] */
.code = BPF_LD | BPF_B | BPF_IND,
.k = sizeof(struct nlattr),
},
...
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sk_filter function is too big to be inlined. This saves 2296 bytes
of text on allyesconfig.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some minor style cleanups:
* Move __KERNEL__ definitions to one place in filter.h
* Use const for sk_filter_len
* Line wrapping
* Put EXPORT_SYMBOL next to function definition
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for block based I/O to SSB.
This is needed in order to efficiently support PIO data
transfers to the card.
The block-I/O support is only compiled, if it's selected by the
weird driver that needs it. So there's no overhead for sane devices.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Turn the SSB bus suspend mechanism upside down.
Instead of deciding by an internal reference count when to suspend/resume,
let the parent bus call us in their suspend/resume routine.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
<linux/mroute.h> needs <linux/types.h>.
Avoid including <linux/in.h> in user-space, which conflicts with
standard <netinet/in.h>.
Add basic struct and constant in <linux/pim.h>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
This does not look good, but there is no other choice. The compilation
without CONFIG_NET is broken and can not be fixed with ease.
After that there is no need for the following commits:
1567ca7eec3edf8fa5cc2d38f9a4f8
Revert them.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the Linux the Intra-Site Automatic Tunnel Addressing
Protocol (ISATAP) implementation. It places the ISATAP potential router
list (PRL) in the kernel and adds three new private ioctls for PRL
management.
[Add several changes of structure name, constant names etc. - yoshfuji]
Signed-off-by: Fred L. Templin <fred.l.templin@boeing.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Currently include/linux/kvm.h is not considered by make headers_install,
because Kbuild cannot handle " unifdef-$(CONFIG_FOO) += foo.h. This problem
was introduced by
commit fb56dbb31c
Author: Avi Kivity <avi@qumranet.com>
Date: Sun Dec 2 10:50:06 2007 +0200
KVM: Export include/linux/kvm.h only if $ARCH actually supports KVM
Currently, make headers_check barfs due to <asm/kvm.h>, which <linux/kvm.h>
includes, not existing. Rather than add a zillion <asm/kvm.h>s, export kvm.
only if the arch actually supports it.
Signed-off-by: Avi Kivity <avi@qumranet.com>
which makes this an 2.6.25 regression.
One way of solving the issue is to enhance Kbuild, but Avi and David conviced
me, that changing headers_install is not the way to go. This patch changes
the definition for linux/kvm.h to unifdef-y.
If unifdef-y is used for linux/kvm.h "make headers_check" will fail on all
architectures without asm/kvm.h. Therefore, this patch also provides
asm/kvm.h on all architectures.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Avi Kivity <avi@qumranet.com>
Cc: Sam Ravnborg <sam@ravnborg.org
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (45 commits)
[VLAN]: Proc entry is not renamed when vlan device name changes.
[IPV6]: Fix ICMP relookup error path dst leak
[ATM] drivers/atm/iphase.c: compilation warning fix
IPv6: do not create temporary adresses with too short preferred lifetime
IPv6: only update the lifetime of the relevant temporary address
bluetooth : __rfcomm_dlc_close lock fix
bluetooth : use lockdep sub-classes for diffrent bluetooth protocol
[ROSE/AX25] af_rose: rose_release() fix
mac80211: correct use_short_preamble handling
b43: Fix PCMCIA IRQ routing
b43: Add DMA mapping failure messages
mac80211: trigger ieee80211_sta_work after opening interface
[LLC]: skb allocation size for responses
[IP] UDP: Use SEQ_START_TOKEN.
[NET]: Remove Documentation/networking/sk98lin.txt
[ATM] atm/idt77252.c: Make 2 functions static
[ATM]: Make atm/he.c:read_prom_byte() static
[IPV6] MCAST: Ensure to check multicast listener(s).
[LLC]: Kill llc_station_mac_sa symbol export.
forcedeth: fix locking bug with netconsole
...
SLAB_DESTROY_BY_RCU is not a direct substitute for normal call_rcu()
freeing, since it'll page freeing but NOT object freeing. So change
cfq to do the freeing on its own.
Signed-off-by: Fabio Checconi <fabio@gandalf.sssup.it>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Recent driver core change causes references to parent devices being
dropped early, at device_del() time, as opposed to when all children
are freed. This causes oops in evdev with grabbed devices. Take the
reference to the parent input device ourselves to ensure that it
stays around long enough.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
As reported by Haavard Skinnemoen and Stephen Rothwell:
> allnoconfig fails with
>
> include/linux/netdevice.h:843: error: implicit declaration of function 'dev_net'
>
> which seems to be because the definition of dev_net is inside #ifdef
> CONFIG_NET, while next_net_device, which calls it, is not.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: ATA_EHI_LPM should be ATA_EH_LPM
pata_sil680: only enable MMIO on Cell blades
