taal_bl_update_status was missing locks to protect taal_data. This caused
a kernel crash randomly, as the code attempted to set the brightness while
the OMAP's DSI block was actually disabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Using nanoseconds as arguments to functions that set the DSI timeouts was
perhaps not so good idea. The timeouts are based on different DSI clocks,
so the possible range for the timeouts vary greatly depending on the
clocks. Also, the multipliers used with the timeouts cause big gaps in the
timeout range, meaning that the nanosecond based functions could cause the
timeout to be quite far from the intended value.
This patch changes the functions to take the plain tick values with the
multiplier enable/disable bits, and sets the TA/LP_RX/HS_TX timeouts to
maximum. While the timeouts could be much lower, the fact is that when
TA/LP_RX/HS_TX timeout happens, we are in an error situation and not in a
hurry anyway.
STOP_STATE_COUNTER is a different matter, but it is only used at
initialization time, and won't normally affect the performance.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Using the shared workqueue led to to a deadlock in the case where the
display was unblanked via keyboard.
What happens is something like this:
- User presses a key
context 1:
- drivers/char/keyboard.c calls schedule_console_callback()
- fb_unblank takes the console semaphore
- dsi bus lock is taken, and frame transfer is started (dsi bus lock is
left on)
- Unblank code tries to set the panel backlight, which tries to take dsi
bus lock, but is blocked while the frame transfer is going on
context 2, shared workqueue, console_callback in drivers/char/vt.c:
- Tries to take console semaphore
- Blocks, as console semaphore is being held by context 1
- No other shared workqueue work can be run
context 3, HW irq, caused by FRAMEDONE interrupt:
- Interrupt handler schedules framedone-work in shared workqueue
- Framedone-work is never ran, as the shared workqueue is blocked. This
means that the unblank thread stays blocked, which means that context 2
stays blocked.
While I think the real problem is in keyboard/virtual terminal code, using
a private workqueue in the DSI driver is perhaps safer and more robust
than using the shared one. The DSI works should not be delayed more than a
millisecond or so, and even if the private workqueue gives us no hard
promise of doing so, it's still safer bet than the shared workqueue.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
dsi_vc_flush_receive_data() is meant to dump data when something has gone
wrong, and thus we should use DSSERR, not DSSDBG.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Trigger WARN_ON() messages from various places in the code in case the
memory region is not currently locked.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
When more than one memory region needs to be lockd at the same time use
the memory region id to fix the order in which the locks are taken. Also
one needs to use the _nested() versions of the locking primitives. The
memory region id can serve as the lock class there as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
R/W semaphore is a good fit for the memory region locking pattern.
So use it.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Add locking to the memory regions to make sure the memory region size
won't be changed while some other piece of code is performing some
checks or setup based on that information.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Separate the memory region from the framebuffer device a little bit.
It's now possible to select the memory region used by the framebuffer
device using the new mem_idx parameter of omapfb_plane_info. If the
mem_idx is specified it will be interpreted as an index into the
memory regions array, if it's not specified the framebuffer's index is
used instead. So by default each framebuffer keeps using it's own
memory region which preserves backwards compatibility.
This allows cloning the same memory region to several overlays and yet
each overlay can be controlled independently since they can be
associated with separate framebuffer devices.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
In omapfb_enable_overlay() if the overlay state is already what we want
skip the set_overlay_info().
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
If video memory hasn't been allocate have check_fb_var() still check
most of the settings, just skip the ones involving the size of the
memory region. Also skip the memory address calculations in
omapfb_setup_overlay() if there's no memory.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Split the overlay address calculations into their own function.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
When there are multiple scaled overlays simply checking whether the update
area intersects any of them in order is not enough. If eg. VID1 starts out
completely outside the update area but VID2 causes the update area to
increase in such a way that VID1 now falls partially within the increased
update area VID1 should be rechecked and the update area possibly
increased even further to fully encompass VID1. So simply keep looping
over the overlays until such time that none of the overlays caused the
update area to change.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
When DSS transitions from off mode to on VENC may generate a spurious
SYNC_LOST_DIGIT error. Just ack it when restoring the context. Also
restore IRQENABLE last to avoid triggering interrupts before the
context is fully restored.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
When the display is not active make the wait_for_go() functions return
immediately.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Check whether the display actually has the set_update_mode() function
before calling it. Only the sysfs codepath was broken, the omapfb ioctl
had the necessary protection.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
For some reason screen updates of certain odd widths seem to be triggering
HS TX timeouts on OMAP 3430, even if bigger updates do not. The reason for
this is unknown, but increasing the timeout removes the problem with no
(so far) noticeable problems. I haven't seen this problem on OMAP 3630.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Add a mutex_unlock missing on the error paths. The use of the mutex is
balanced elsewhere in the file.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E1;
@@
* mutex_lock(E1,...);
<+... when != E1
if (...) {
... when != E1
* return ...;
}
...+>
* mutex_unlock(E1,...);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* Add tft display module compatibility for new
hardware modules
Signed-off-by: Adrian Alonso <aalonso00@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Adds support for encoding display mode information
in the device tree using verbatim EDID block.
If the EDID entry in the DIU node is present, the
driver will build mode database using EDID data
and allow setting the display modes from this database.
Otherwise display mode will be set using mode
entries from driver's internal database as usual.
This patch also updates device tree bindings.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
MPC5121 DIU configuration/setup as initialized by the boot
loader currently will get lost while booting Linux. As a
result displaying the boot splash is not possible through
the boot process.
To prevent this we reserve configured DIU frame buffer
address range while booting and preserve AOI descriptor
and gamma table so that DIU continues displaying through
the whole boot process. On first open from user space
DIU frame buffer driver releases the reserved frame
buffer area and continues to operate as usual.
Signed-off-by: John Rigby <jcrigby@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Some DIU structures will be used in platform code in
subsequent MPC5121 DIU patch, so we move this header
to be able to include it elsewhere.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
On MPC5121e Rev 2.0 re-configuring the DIU area descriptor
by writing new descriptor address doesn't always work.
As a result, DIU continues to display using old area descriptor
even if the new one has been written to the descriptor register of
the plane.
Add the code from Freescale MPC5121EADS BSP for writing descriptor
addresses properly. This fixes the problem for Rev 2.0 silicon.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch moves the declaration of of_get_address(), of_get_pci_address(),
and of_pci_address_to_resource() out of arch code and into the common
linux/of_address header file.
This patch also fixes some of the asm/prom.h ordering issues. It still
includes some header files that it ideally shouldn't be, but at least the
ordering is consistent now so that of_* overrides work.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* master.kernel.org:/home/rmk/linux-2.6-arm:
cyber2000fb: fix console in truecolor modes
cyber2000fb: fix machine hang on module load
SA1111: Eliminate use after free
ARM: Fix Versatile/Realview/VExpress MMC card detection sense
ARM: 6279/1: highmem: fix SMP preemption bug in kmap_high_l1_vipt
ARM: Add barriers to io{read,write}{8,16,32} accessors as well
ARM: 6273/1: Add barriers to the I/O accessors if ARM_DMA_MEM_BUFFERABLE
ARM: 6272/1: Convert L2x0 to use the IO relaxed operations
ARM: 6271/1: Introduce *_relaxed() I/O accessors
ARM: 6275/1: ux500: don't use writeb() in uncompress.h
ARM: 6270/1: clean files in arch/arm/boot/compressed/
ARM: Fix csum_partial_copy_from_user()
Return value was not set to 0 in setcolreg() with truecolor modes. This causes
fb_set_cmap() to abort after first color, resulting in blank palette - and
blank console in 24bpp and 32bpp modes.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I was testing two CyberPro 2000 based PCI cards on x86 and the machine always
hanged completely when the cyber2000fb module was loaded. It seems that the
card hangs when some registers are accessed too quickly after writing RAMDAC
control register. With this patch, both card work.
Add delay after RAMDAC control register write to prevent hangs on module load.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Repair a section mismatch between the mddi driver's
platform_driver structure and its probe method.
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
WARNING: drivers/video/built-in.o(.data+0x360): Section mismatch in reference from the variable au1100fb_driver to the function .init.text:au1100fb_drv_probe()
The variable au1100fb_driver references
the function __init au1100fb_drv_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Fixing which triggers of a slew of further mismatches:
WARNING: drivers/video/built-in.o(.devinit.text+0xc0): Section mismatch in reference from the function au1100fb_drv_probe() to the variable .init.data:au1100fb_fix
The function __devinit au1100fb_drv_probe() references
a variable __initdata au1100fb_fix.
If au1100fb_fix is only used by au1100fb_drv_probe then
annotate au1100fb_fix with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x21c): Section mismatch in reference from the function au1100fb_drv_probe() to the variable .init.data:au1100fb_var
The function __devinit au1100fb_drv_probe() references
a variable __initdata au1100fb_var.
If au1100fb_var is only used by au1100fb_drv_probe then
annotate au1100fb_var with a matching annotation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
WARNING: drivers/built-in.o(.devinit.text+0xc0): Section mismatch in reference from the function pmagbafb_probe() to the variable .init.data:pmagbafb_fix
The function __devinit pmagbafb_probe() references
a variable __initdata pmagbafb_fix.
If pmagbafb_fix is only used by pmagbafb_probe then
annotate pmagbafb_fix with a matching annotation.
Fixing this one triggers a few more mismatches in order:
WARNING: drivers/video/built-in.o(.devinit.text+0x414): Section mismatch in reference from the function pmagbbfb_probe() to the variable .init.data:pmagbbfb_fix
The function __devinit pmagbbfb_probe() references
a variable __initdata pmagbbfb_fix.
If pmagbbfb_fix is only used by pmagbbfb_probe then
annotate pmagbbfb_fix with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x45c): Section mismatch in reference from the function pmagbbfb_probe() to the variable .init.data:pmagbbfb_defined
The function __devinit pmagbbfb_probe() references
a variable __initdata pmagbbfb_defined.
If pmagbbfb_defined is only used by pmagbbfb_probe then
annotate pmagbbfb_defined with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x5fc): Section mismatch in reference from the function pmagbbfb_probe() to the function .init.text:pmagbbfb_screen_setup()
The function __devinit pmagbbfb_probe() references
a function __init pmagbbfb_screen_setup().
If pmagbbfb_screen_setup is only used by pmagbbfb_probe then
annotate pmagbbfb_screen_setup with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x6f4): Section mismatch in reference from the function pmagbbfb_probe() to the function .init.text:pmagbbfb_osc_setup()
The function __devinit pmagbbfb_probe() references
a function __init pmagbbfb_osc_setup().
If pmagbbfb_osc_setup is only used by pmagbbfb_probe then
annotate pmagbbfb_osc_setup with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x5f8): Section mismatch in reference from the function pmagbbfb_osc_setup() to the variable .init.data:pmagbbfb_freqs.15993
The function __devinit pmagbbfb_osc_setup() references
a variable __initdata pmagbbfb_freqs.15993.
If pmagbbfb_freqs.15993 is only used by pmagbbfb_osc_setup then
annotate pmagbbfb_freqs.15993 with a matching annotation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
WARNING: drivers/video/built-in.o(.data+0x1e0): Section mismatch in reference fr
om the variable pmagbafb_driver to the function .init.text:pmagbafb_probe()
The variable pmagbafb_driver references
the function __init pmagbafb_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Fixing this one triggers 2 more:
WARNING: drivers/video/built-in.o(.devinit.text+0xc0): Section mismatch in reference from the function pmagbafb_probe() to the variable .init.data:pmagbafb_fix
The function __devinit pmagbafb_probe() references
a variable __initdata pmagbafb_fix.
If pmagbafb_fix is only used by pmagbafb_probe then
annotate pmagbafb_fix with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x108): Section mismatch in reference from the function pmagbafb_probe() to the variable .init.data:pmagbafb_defined
The function __devinit pmagbafb_probe() references
a variable __initdata pmagbafb_defined.
If pmagbafb_defined is only used by pmagbafb_probe then
annotate pmagbafb_defined with a matching annotation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
WARNING: drivers/video/built-in.o(.devinit.text+0x54): Section mismatch in reference from the function gbefb_probe() to the function .init.text:gbefb_setup()
The function __devinit gbefb_probe() references
a function __init gbefb_setup().
If gbefb_setup is only used by gbefb_probe then
annotate gbefb_setup with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x208): Section mismatch in reference from the function gbefb_probe() to the variable .init.data:mode_option
The function __devinit gbefb_probe() references
a variable __initdata mode_option.
If mode_option is only used by gbefb_probe then
annotate mode_option with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x214): Section mismatch in reference from the function gbefb_probe() to the variable .init.data:default_mode
The function __devinit gbefb_probe() references
a variable __initdata default_mode.
If default_mode is only used by gbefb_probe then
annotate default_mode with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x23c): Section mismatch in reference from the function gbefb_probe() to the variable .init.data:default_var
The function __devinit gbefb_probe() references
a variable __initdata default_var.
If default_var is only used by gbefb_probe then
annotate default_var with a matching annotation.
Fixing these results in more mismatches:
WARNING: drivers/video/built-in.o(.devinit.text+0x3c): Section mismatch in reference from the function gbefb_setup() to the variable .init.data:default_var_LCD
The function __devinit gbefb_setup() references
a variable __initdata default_var_LCD.
If default_var_LCD is only used by gbefb_setup then
annotate default_var_LCD with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x14c): Section mismatch in reference from the function gbefb_setup() to the variable .init.data:default_mode_LCD
The function __devinit gbefb_setup() references
a variable __initdata default_mode_LCD.
If default_mode_LCD is only used by gbefb_setup then
annotate default_mode_LCD with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x150): Section mismatch in reference from the function gbefb_setup() to the variable .init.data:default_var_CRT
The function __devinit gbefb_setup() references
a variable __initdata default_var_CRT.
If default_var_CRT is only used by gbefb_setup then
annotate default_var_CRT with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x154): Section mismatch in reference from the function gbefb_setup() to the variable .init.data:default_mode_CRT
The function __devinit gbefb_setup() references
a variable __initdata default_mode_CRT.
If default_mode_CRT is only used by gbefb_setup then
annotate default_mode_CRT with a matching annotation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Both of_bus_type and of_platform_bus_type are just #define aliases
for the platform bus. This patch removes all references to them and
switches to the of_register_platform_driver()/of_unregister_platform_driver()
API for registering.
Subsequent patches will convert each user of of_register_platform_driver()
into plain platform_drivers without the of_platform_driver shim. At which
point the of_register_platform_driver()/of_unregister_platform_driver()
functions can be removed.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
viafb: fix accel_flags check_var bug
In check_var we should check and modify the var given and not the
one which is currently active. So this code was obviously wrong.
Probably this was doing no harm because all acceleration functions
also check whether acceleration is possible. (otherwise I would
expect this to lead to a null pointer dereference)
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
viafb: probe cleanups
Removal of strange special cases that must not exist as well as a
useless check.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
viafb: remove ioctls which break the framebuffer interface
The ioctls VIAFB_SET_DEVICE, VIAFB_SET_DEVICE_INFO and
VIAFB_SET_SECOND_MODE are removed because they prevent a clean
framebuffer driver because they modify the hardware and/or the
internal structures.
There are no known applications using these ioctls so no breakage is
expected. Additionaly the main functionality was duplicating the
framebuffer interface so there really should not exist any user.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
viafb: update fix before calculating depth
As the depth calculation depends on information in fix it is saner to
do the update first.
No runtime change expected as the value visual in fix used never
changes to MONO.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
viafb: PLL value cleanup
This is a big change of how PLL values are handled on the road to
dynamic PLL value generation. The table was converted automatically in
the relevant parameters for frequency generation. Sadly there were some
bits set whose meaning is unknown. Those differences are documented
but ignored as the unichrome code implies that they are not important
(a big thanks to Luc for his amazing work).
The PLL values for 31490000 and 133308000 are deleted as they were more
than 5% off and not used anyway. The values for CX700@60466000 and
VX855@153920000 are corrected as they were wrong and easily correctable
as enough correct values was available because CX700 and VX855 support
the same values only with a little difference in hardware format.
All remaining values are not more than 2% off.
Additionally the surrounding code is changed as needed especially the
byte order of the values written to hardware to allow nicer conversion
functions.
This is mostly a change preparing for dynamic PLL generation and the two
corrected values aside no runtime change is expected.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
viafb: simplify lcd size "detection"
Remove all occurences of get_lcd_size_method as only the values
GET_LCD_SIZE_BY_VGA_BIOS and GET_LCD_SIZE_BY_USER_SETTING were used
which had the identical code so there is no need to make things look
more complicated than they actually are.
Just a bit of of cleanup, really no regressions expected.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
viafb: fix PCI table
This patch fixes an oddity in the device table where the P4M890 ID was
assigned with the enumeration value of CN700 which itself was missing.
This is a regression introduced by
"viafb: make viafb a first-class citizen using pci_driver"
While at it reorder the table to reflect the order of the enumeration
values.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Harald Welte <laforge@gnumonks.org>
viafb: add lcd scaling support for some IGPs
These IGPs should also support lcd scaling but likely this switch was
missed when adding support for them. Fix it, allowing lcd scaling on
CN750, VX800 and VX855. At least this improves the situation for
VX855. (there seems to be another scaling unrelated bug somewhere)
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
viafb: improve lcd code readability
This changes the code to better reflect that we can (currently) only
perform upscaling.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
viafb: remove duplicated scaling code
The code for P4M900 does the same as for all newer IGPs so there is no
reason to duplicate it. Just reducing the code to maintain.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
Initialize basic pv on hvm features adding a new Xen HVM specific
hypervisor_x86 structure.
Don't try to initialize xen-kbdfront and xen-fbfront when running on HVM
because the backends are not available.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Pointed out by Lucas who found the new one in a comment in
setup_percpu.c. And then I fixed the others that I grepped
for.
Reported-by: Lucas <canolucas@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pavel@suse.cz no longer works, replace it with working address.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Otherwise we have to disable it manually to avoid compile errors.
Now it's only enabled only for the selected machines as suggested
by Anton Vorontsov <cbouatmailru@gmail.com>:
$ git grep VGA_CONSOLE= arch/arm/configs/
arch/arm/configs/footbridge_defconfig:CONFIG_VGA_CONSOLE=y
arch/arm/configs/integrator_defconfig:CONFIG_VGA_CONSOLE=y
arch/arm/configs/netwinder_defconfig:CONFIG_VGA_CONSOLE=y
Note that the Kconfig entry no longer needs separate entries
for ARCH_ACORN, ARCH_EBSA110 ARCH_VERSATILE.
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the new mux function for that.
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix a nuc900 lcd build error.
Since the 'nuc900_driver_clksrc_div()' API cannot be merged into mainline
successfully, I removed this clock source selection hook in this driver.
This means nuc900 lcd driver has to select default clock source from the
external crystal now.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Qiang Wang <rurality.wq@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARNING: vmlinux.o(.data+0x196e8): Section mismatch in reference from the
variable lxfb_driver to the function .init.text:lxfb_probe() The variable
lxfb_driver references the function __init lxfb_probe()
This changes lxfb_probe and friends to use __devinit, and also adds
__devexit to lxfb_remove.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARNING: vmlinux.o(.data+0x195d8): Section mismatch in reference from the
variable gxfb_driver to the function .init.text:gxfb_probe() The variable
gxfb_driver references the function __init gxfb_probe()
This changes gxfb_probe and friends to use __devinit, and also adds
__devexit to gxfb_remove.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Just dropping a couple of warnings from this driver,
linux-2.6/drivers/video/msm/mdp.c: In function 'get_img':
linux-2.6/drivers/video/msm/mdp.c:261: warning: unused variable 'vstart'
linux-2.6/drivers/video/msm/mddi.c: In function 'mddi_handle_rev_data_avail':
linux-2.6/drivers/video/msm/mddi.c:193: warning: unused variable 'i'
linux-2.6/drivers/video/msm/mddi.c:190: warning: unused variable 'rev'
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
The code in rfbi.c tried to get the omapdss platform_device via a static
member defined in dispc.c, leading to a compile error. The same
platform_device is available through rfbi-struct.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
I was observing the following error messages on my OMAP1 based Amstrad Delta
board when first changing from text to graphics mode or vice versa after the
LCD display had been blanked:
omapfb omapfb: timeout waiting for FRAME DONE
with a followup error message while unblanking it back:
omapfb omapfb: resetting (status 0xffffffb2,reset count 1)
As a visible result, image pixels happened to be shifted by a few bits,
giving wrong colors.
Examining the code, I found that this problem occures when an OMAP1 internal
LCD controller is disabled from omap_lcdc_suspend() and then a subsequent
omap_lcdc_setup_plane() calls disable_controller() again. This potentially
error provoking behaviour is triggered by the lcdc.update_mode flag being kept
at OMAP_AUTO_UPDATE, regardless of the controller and panel being suspended.
This patch tries to correct the problem by replacing both omap_lcdc_suspend()
and omap_lcdc_resume() function bodies with single calls to
omap_lcdc_set_update_mode() with a respective OMAP_UPDATE_DISABLE or
OMAP_AUTO_UPDATE argument. As a result, exactly the same lower level
operations are performed, with addition of changing the lcdc.update_mode flag
to a value better suited for the controller state. This prevents any further
calls to disable_controller() from omap_lcdc_setup_plane() while the display
is suspended.
Created against linux-2.6.34-rc7.
Tested on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (23 commits)
sh: Make intc messages consistent via pr_fmt.
sh: make sure static declaration on ms7724se
sh: make sure static declaration on mach-migor
sh: make sure static declaration on mach-ecovec24
sh: make sure static declaration on mach-ap325rxa
clocksource: sh_cmt: compute mult and shift before registration
clocksource: sh_tmu: compute mult and shift before registration
sh: PIO disabling for x3proto and urquell.
sh: mach-sdk7786: conditionally disable PIO support.
sh: support for platforms without PIO.
usb: r8a66597-hcd pio to mmio accessor conversion.
usb: gadget: r8a66597-udc pio to mmio accessor conversion.
usb: gadget: m66592-udc pio to mmio accessor conversion.
sh: add romImage MMCIF boot for sh7724 and Ecovec V2
sh: add boot code to MMCIF driver header
sh: prepare MMCIF driver header file
sh: allow romImage data between head.S and the zero page
sh: Add support MMCIF for ecovec
sh: remove duplicated #include
input: serio: disable i8042 for non-cayman sh platforms.
...
Commit f601441916 ("imxfb: add support for
i.MX25:) has inserted the symbol HAVE_FB_IMX, which does not depend on FB
after the menuconfig FB. This breaks the menu, presenting most of the
drivers outside of it, when using menuconfig.
Moving the symbol to the start of the file, just like HAVE_FB_ATMEL, fixes
the problem without breaking it for iMX25 configurations (tested with
ARCH=arm, no build).
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As pointed by Nick Piggin, ->page_mkwrite provides a way to keep a page
locked until the associated PTE is marked dirty.
Re-implement the fix by using this mechanism.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Acked-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 49bbd815fd ("fb_defio:
fix for non-dirty ptes").
Although the fix provided is correct, it's been suggested to avoid the
underlying race in the same way as it is currently done in filesystems
like NFS, for maintainability.
A following patch "fb_defio: redo fix for non-dirty ptes" will provide
such an alternate fix.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Cc: Jaya Kumar <jayakumar.lkml@gmail.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I2C drivers can use the clientdata-pointer to point to private data. As I2C
devices are not really unregistered, but merely detached from their driver, it
used to be the drivers obligation to clear this pointer during remove() or a
failed probe(). As a couple of drivers forgot to do this, it was agreed that it
was cleaner if the i2c-core does this clearance when appropriate, as there is
no guarantee for the lifetime of the clientdata-pointer after remove() anyhow.
This feature was added to the core with commit
e4a7b9b04d to fix the faulty drivers.
As there is no need anymore to clear the clientdata-pointer, remove all current
occurrences in the drivers to simplify the code and prevent confusion.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fixes build errors in a number of framebuffer drivers caused
by the OF device_node pointer being moved into struct device
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Use the same color-calculating algorithm as in atyfb_imageblit in this
driver or in generic cfb_fillrect.
This patch fixes bad colors when using an accelerator in 15-bit and
16-bit modes.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current backlight code is stubbed out, so the new props changes added
some warnings:
drivers/video/bf54x-lq043fb.c: In function 'bfin_bf54x_probe':
drivers/video/bf54x-lq043fb.c:666: warning: label 'out9' defined but not used
drivers/video/bf54x-lq043fb.c:504: warning: unused variable 'props'
Fix em !
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current backlight code is stubbed out, so the new props changes added
some warnings about unused label/prop.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use memdup_user when user data is immediately copied into the
allocated region.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@
- to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+ to = memdup_user(from,size);
if (
- to==NULL
+ IS_ERR(to)
|| ...) {
<+... when != goto l1;
- -ENOMEM
+ PTR_ERR(to)
...+>
}
- if (copy_from_user(to, from, size) != 0) {
- <+... when != goto l2;
- -EFAULT
- ...+>
- }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for S3 Trio3D/1X (86C360) and S3 Trio3D/2X (86C362 and 86C368)
cards to s3fb driver. Tested with 86C362 AGP and 86C368 PCI&AGP.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Ondrej Zajicek <santiago@crfreenet.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds a backlight driver for controlling the pcf50633 LED module.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
This patch properly unregisters a previously registered backlight device object
in error handling
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Properly unregister a previously registered backlight device object in error
handling of max8925_backlight_probe.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Error handling fixes:
1. In the case of kzalloc failure, simple return -ENOMEM instead of goto
err. ( priv is NULL in this case )
2. In the case of gpio_request fail for reset_gpio and data_enable_gpio,
properly release resources by goto err and err2 respectively.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
This is S6E63M0 AMOLED LCD Panel(480x800) driver using 3-wired SPI
interface also almost features for lcd panel driver has been implemented
in here. and I added new structure common for all the lcd panel drivers
to include/linux/lcd.h file.
LCD Panel driver needs interfaces for controlling device power such as
power on/off and reset. these interfaces are device specific so it should
be implemented to machine code at this time, we should create new
structure for registering these functions as callbacks and also a header
file for that structure and finally registered callback functions would be
called by lcd panel driver. such header file(including new structure for
lcd panel) would be added for all the lcd panel drivers.
If anyone provides common structure for registering such callback
functions then we could reduce unnecessary header files for lcd panel. I
thought that suitable anyone could be include/linux/lcd.h so a new
lcd_platform_data structure was added there.
[akpm@linux-foundation.org: coding-style fixes]
[randy.dunlap@oracle.com: fix s6e63m0 kconfig]
[randy.dunlap@oracle.com: fix device attribute functions return types]
Signed-off-by: InKi Dae <inki.dae@samsung.com>
Reviewed-by: KyungMin Park <kyungmin.park.samsung.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Fix DMI_SYS_VENDOR for MacBook1,1.
When the MacBook1,1 came out Apple was still named Apple Computer, I am
not sure if this applies to older MacBook2,1 versions aswell.
Signed-off-by: Steffen Röcker <sroecker@gmail.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
The EP9307, EP9312, and EP9315 processors include a framebuffer
peripheral. This peripheral has a dedicated pwm output called
BRIGHT that can be used to control the backlight on an LCD.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Add slab.h to fix part of build.
Add a parameter in backlight_device_register() call to fix part of build.
drivers/video/backlight/adp8860_bl.c:215: error: implicit declaration of function 'kzalloc'
drivers/video/backlight/adp8860_bl.c:215: warning: assignment makes pointer from integer without a cast
drivers/video/backlight/adp8860_bl.c:285: error: implicit declaration of function 'kfree'
drivers/video/backlight/adp8860_bl.c:673: warning: assignment makes pointer from integer without a cast
drivers/video/backlight/adp8860_bl.c:689: error: too few arguments to function 'backlight_device_register'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
The ADP8860 combines a programmable backlight LED charge pump driver with
automatic phototransistor control.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
I added a kfree() on the error path. I don't really expect it to affect
anyone, but it's easy and makes the static checkers happy.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Add support for all remaining models not yet present in Linus'/Richard
Purdie's tree nor Evan McClain's patch to finally complete the list.
Signed-off-by: Mario Schwalbe <schwalbe@inf.tu-dresden.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Cleanup the "depends on" logic by wrapping the affected config options in
appropriate if/endif blocks.
Remove all the "default n" since that is the default default.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
backlight_device_register() returns a valid pointer or ERR_PTR() never
NULL.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
We should be releasing "res->start" here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Wang Qiang <rurality.linux@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a problem observed while using fb_defio with a short delay on a
PowerPC platform.
It is possible that page_mkclean() is invoked in the deferred io work
function _before_ a PTE has been marked dirty. In this case, the page is
removed from the defio pagelist but page_mkclean() does not write-protect
the page again. The end result is that defio ignores all subsequent
writes to the page and the corresponding portions of the framebuffer never
get updated.
The fix consists in keeping track of the pages with non-dirty PTEs,
re-checking them again on the next deferred io work iteration. Note that
those pages are not passed to the defio callback as they are not written
by userspace yet.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Acked-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since the drivers probe call was changed from .init.text to .devinit.text
in commit c2e13037e6 ("platform-drivers:
move probe to .devinit.text in drivers/video") the fb_fix_screeninfo and
fb_var_screeninfo structures must be changed from .init.data to
.devinit.data, too.
Also the drivers remove routine should be moved from .text to .devexit.text
It removes these 7 section mismatch warnings from modpost:
WARNING: vmlinux.o(.devinit.text+0x1e28): Section mismatch in reference from the function sgivwfb_probe() to the variable .init.data:sgivwfb_fix
The function __devinit sgivwfb_probe() references
a variable __initdata sgivwfb_fix.
If sgivwfb_fix is only used by sgivwfb_probe then
annotate sgivwfb_fix with a matching annotation.
WARNING: vmlinux.o(.devinit.text+0x1e50): Section mismatch in reference from the function sgivwfb_probe() to the (unknown reference) .init.data:(unknown)
The function __devinit sgivwfb_probe() references
a (unknown reference) __initdata (unknown).
If (unknown) is only used by sgivwfb_probe then
annotate (unknown) with a matching annotation.
WARNING: vmlinux.o(.devinit.text+0x1e59): Section mismatch in reference from the function sgivwfb_probe() to the (unknown reference) .init.data:(unknown)
The function __devinit sgivwfb_probe() references
a (unknown reference) __initdata (unknown).
If (unknown) is only used by sgivwfb_probe then
annotate (unknown) with a matching annotation.
WARNING: vmlinux.o(.devinit.text+0x1e60): Section mismatch in reference from the function sgivwfb_probe() to the variable .init.data:sgivwfb_fix
The function __devinit sgivwfb_probe() references
a variable __initdata sgivwfb_fix.
If sgivwfb_fix is only used by sgivwfb_probe then
annotate sgivwfb_fix with a matching annotation.
WARNING: vmlinux.o(.devinit.text+0x1e6a): Section mismatch in reference from the function sgivwfb_probe() to the (unknown reference) .init.data:(unknown)
The function __devinit sgivwfb_probe() references
a (unknown reference) __initdata (unknown).
If (unknown) is only used by sgivwfb_probe then
annotate (unknown) with a matching annotation.
WARNING: vmlinux.o(.devinit.text+0x1e7f): Section mismatch in reference from the function sgivwfb_probe() to the variable .init.data:sgivwfb_var1600sw
The function __devinit sgivwfb_probe() references
a variable __initdata sgivwfb_var1600sw.
If sgivwfb_var1600sw is only used by sgivwfb_probe then
annotate sgivwfb_var1600sw with a matching annotation.
WARNING: vmlinux.o(.devinit.text+0x1e91): Section mismatch in reference from the function sgivwfb_probe() to the variable .init.data:sgivwfb_var
The function __devinit sgivwfb_probe() references
a variable __initdata sgivwfb_var.
If sgivwfb_var is only used by sgivwfb_probe then
annotate sgivwfb_var with a matching annotation.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since the drivers probe calls were changed from .init.text to
.devinit.text in commit c2e13037e6
("platform-drivers: move probe to .devinit.text in drivers/video") all the
function from .init.text should be moved to .devinit.text, too.
The drivers remove calls can also be move from .text to .devexit.text.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Cc: Vincent Sanders <support@simtec.co.uk>
Acked-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since the drivers probe call was changed from .init.text to .devinit.text
in commit c2e13037e6 ("platform-drivers:
move probe to .devinit.text in drivers/video") the fb_fix_screeninfo and
fb_var_screeninfo structures must be changed from .init.data to
.devinit.data, too.
Also the drivers remove routine should be moved from .exit.text to
.devexit.text
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
FBIO_WAITFORVSYNC is currently implemented by matroxfb, atyfb, intelfb and
more. All of them keep redefining the same FBIO_WAITFORVSYNC macro over
and over again, so move it to linux/fb.h and clean up those duplicate
defines.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Maik Broemme <mbroemme@plusserver.de>
Cc: Petr Vandrovec <vandrove@vc.cvut.cz>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: "Hiremath, Vaibhav" <hvaibhav@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This work includes the following:
- Implement handler for FBIO_WAITFORVSYNC ioctl.
- Allocate the data and palette buffers separately. A consequence of
this is that the palette and data loading is now done in different
phases. And that the LCD must be disabled temporarily after the palette
is loaded but this will only happen once after init and each time the
palette is changed. I think this is OK.
- Allocate two (ping and pong) framebuffers from memory.
- Add pan_display handler which toggles the LCDC DMA registers between
the ping and pong buffers.
Signed-off-by: Martin Ambrose <martin@ti.com>
Cc: Chaithrika U S <chaithrika@ti.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up the section in the w100fb driver, by moving:
* w100fb_remove() from .text to .devexit.text
* w100_get_xtal_table() from .text to .devinit.text
* w100fb_init() from .devinit.text to .init.text
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: <stable@kernel.org> [if "platform-drivers: move probe to .devinit.text in drivers/video" was merged]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up the sections in the vga16fb driver, by moving:
* the variables vga16_defined and vga16fb
from .init.data to .devinit.data
* vga16fb_setup() from .text to .init.text
* vga16fb_remove() from .text. to .devexit.text
This fixes the following warnings issued by modpost:
WARNING: drivers/video/built-in.o(.devinit.text+0x1a420): Section mismatch in re
ference from the function vga16fb_probe() to the (unknown reference) .init.data:
(unknown)
The function __devinit vga16fb_probe() references
a (unknown reference) __initdata (unknown).
If (unknown) is only used by vga16fb_probe then
annotate (unknown) with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x1a437): Section mismatch in reference from the function vga16fb_probe() to the variable .init.data:vga16fb_defined
The function __devinit vga16fb_probe() references
a variable __initdata vga16fb_defined.
If vga16fb_defined is only used by vga16fb_probe then
annotate vga16fb_defined with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x1a457): Section mismatch in reference from the function vga16fb_probe() to the variable .init.data:vga16fb_fix
The function __devinit vga16fb_probe() references
a variable __initdata vga16fb_fix.
If vga16fb_fix is only used by vga16fb_probe then
annotate vga16fb_fix with a matching annotation.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: <stable@kernel.org> [if "platform-drivers: move probe to .devinit.text in drivers/video" was merged]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up the section in the vfb driver, by moving the variables vfb_default
and vfb_fix from .init.data to .devinit.data
This fixes the following warnings issued by modpost:
WARNING: drivers/video/vfb.o(.devinit.text+0xf8): Section mismatch in reference from the function vfb_probe() to the variable .init.data:vfb_default
The function __devinit vfb_probe() references
a variable __initdata vfb_default.
If vfb_default is only used by vfb_probe then
annotate vfb_default with a matching annotation.
WARNING: drivers/video/vfb.o(.devinit.text+0x114): Section mismatch in reference from the function vfb_probe() to the variable .init.data:vfb_fix
The function __devinit vfb_probe() references
a variable __initdata vfb_fix.
If vfb_fix is only used by vfb_probe then
annotate vfb_fix with a matching annotation.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: <stable@kernel.org> [if "platform-drivers: move probe to .devinit.text in drivers/video" was merged]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up the sections in the hgafb driver, by
* moving hga_default_var and hga_fix from .init.data to .devinit.data
* moving hga_detect() from .init.text to .devinit.text
* moving hga_fb_remove() from .text to .devexit.text
This fixes the following warnings issued by modpost:
WARNING: drivers/video/hgafb.o(.devinit.text+0x18): Section mismatch in referenc
e from the function hgafb_probe() to the function .init.text:hga_card_detect()
The function __devinit hgafb_probe() references
a function __init hga_card_detect().
If hga_card_detect is only used by hgafb_probe then
annotate hga_card_detect with a matching annotation.
WARNING: drivers/video/hgafb.o(.devinit.text+0xfe): Section mismatch in referenc
e from the function hgafb_probe() to the variable .init.data:hga_fix
The function __devinit hgafb_probe() references
a variable __initdata hga_fix.
If hga_fix is only used by hgafb_probe then
annotate hga_fix with a matching annotation.
WARNING: drivers/video/hgafb.o(.devinit.text+0x105): Section mismatch in reference from the function hgafb_probe() to the variable .init.data:hga_default_var
The function __devinit hgafb_probe() references
a variable __initdata hga_default_var.
If hga_default_var is only used by hgafb_probe then
annotate hga_default_var with a matching annotation.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: <stable@kernel.org> [if "platform-drivers: move probe to .devinit.text in drivers/video" was merged]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the sections in the arcfb driver, by moving:
* the variables arcfb_fix and arcfb_var from .init.data to .devinit.data
* arcfb_remove() from .text to .devexit.text
This fixes the following warnings issued by modpost:
WARNING: drivers/video/built-in.o(.devinit.text+0x543): Section mismatch in reference from the function arcfb_probe() to the variable .init.data:arcfb_var
The function __devinit arcfb_probe() references
a variable __initdata arcfb_var.
If arcfb_var is only used by arcfb_probe then
annotate arcfb_var with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x558): Section mismatch in reference from the function arcfb_probe() to the variable .init.data:arcfb_fix
The function __devinit arcfb_probe() references
a variable __initdata arcfb_fix.
If arcfb_fix is only used by arcfb_probe then
annotate arcfb_fix with a matching annotation.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: <stable@kernel.org> [if "platform-drivers: move probe to .devinit.text in drivers/video" was merged]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These are different size buffers (40 chars vs 16), we may as well be
cautious.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This lets us support the new BF527-EZKIT V2.1 via platform resources
tweaks only.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some SH-mobile SoCs have a MIPI DSI controller, that can be used to connect
MIPI displays to LCDC. This patch adds a platform driver for SH-mobile MIPI DSI
unit. It uses existing hooks in the sh_mobile_lcdcfb.c driver for display
activation and deactivation.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Fix printk formats:
drivers/video/fbmem.c: In function 'fb_do_apertures_overlap':
drivers/video/fbmem.c:1494: warning: format '%llx' expects type 'long long unsigned int', but argument 2 has type 'resource_size_t'
drivers/video/fbmem.c:1494: warning: format '%llx' expects type 'long long unsigned int', but argument 3 has type 'resource_size_t'
drivers/video/fbmem.c:1494: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'resource_size_t'
drivers/video/fbmem.c:1494: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'resource_size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
DMAENGINE: extend the control command to include an arg
async_tx: trim dma_async_tx_descriptor in 'no channel switch' case
DMAENGINE: DMA40 fix for allocation of logical channel 0
DMAENGINE: DMA40 support paused channel status
dmaengine: mpc512x: Use resource_size
DMA ENGINE: Do not reset 'private' of channel
ioat: Remove duplicated devm_kzalloc() calls for ioatdma_device
ioat3: disable cacheline-unaligned transfers for raid operations
ioat2,3: convert to producer/consumer locking
ioat: convert to circ_buf
DMAENGINE: Support for ST-Ericssons DMA40 block v3
async_tx: use of kzalloc/kfree requires the include of slab.h
dmaengine: provide helper for setting txstate
DMAENGINE: generic channel status v2
DMAENGINE: generic slave control v2
dma: timb-dma: Update comment and fix compiler warning
dma: Add timb-dma
DMAENGINE: COH 901 318 fix bytesleft
DMAENGINE: COH 901 318 rename confusing vars
* 'drm-for-2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (207 commits)
drm/radeon/kms/pm/r600: select the mid clock mode for single head low profile
drm/radeon: fix power supply kconfig interaction.
drm/radeon/kms: record object that have been list reserved
drm/radeon: AGP memory is only I/O if the aperture can be mapped by the CPU.
drm/radeon/kms: don't default display priority to high on rs4xx
drm/edid: fix typo in 1600x1200@75 mode
drm/nouveau: fix i2c-related init table handlers
drm/nouveau: support init table i2c device identifier 0x81
drm/nouveau: ensure we've parsed i2c table entry for INIT_*I2C* handlers
drm/nouveau: display error message for any failed init table opcode
drm/nouveau: fix init table handlers to return proper error codes
drm/nv50: support fractional feedback divider on newer chips
drm/nv50: fix monitor detection on certain chipsets
drm/nv50: store full dcb i2c entry from vbios
drm/nv50: fix suspend/resume with DP outputs
drm/nv50: output calculated crtc pll when debugging on
drm/nouveau: dump pll limits entries when debugging is on
drm/nouveau: bios parser fixes for eDP boards
drm/nouveau: fix a nouveau_bo dereference after it's been destroyed
drm/nv40: remove some completed ctxprog TODOs
...
This allows bin_attr->read,write,mmap callbacks to check file specific data
(such as inode owner) as part of any privilege validation.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'viafb-next' of git://git.lwn.net/linux-2.6: (35 commits)
viafb: move some include files to include/linux
viafb: Eliminate some global.h references
viafb: get rid of i2c debug cruft
viafb: fold via_io.h into via-core.h
viafb: Fix initialization error paths
viafb: Do not remove gpiochip under spinlock
viafb: make procfs entries optional
viafb: fix proc entry removal
viafb: improve misc register handling
viafb: replace inb/outb
viafb: move some modesetting functions to a seperate file
viafb: unify modesetting functions
viafb: Reserve framebuffer memory for the upcoming camera driver
viafb: Add a simple VX855 DMA engine driver
viafb: Add a simple interrupt management infrastructure
via: Rationalize vt1636 detection
viafb: Introduce viafb_find_i2c_adapter()
via: Do not attempt I/O on inactive I2C adapters
viafb: Turn GPIO and i2c into proper platform devices
viafb: Convert GPIO and i2c to the new indexed port ops
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits)
vlynq: make whole Kconfig-menu dependant on architecture
add descriptive comment for TIF_MEMDIE task flag declaration.
EEPROM: max6875: Header file cleanup
EEPROM: 93cx6: Header file cleanup
EEPROM: Header file cleanup
agp: use NULL instead of 0 when pointer is needed
rtc-v3020: make bitfield unsigned
PCI: make bitfield unsigned
jbd2: use NULL instead of 0 when pointer is needed
cciss: fix shadows sparse warning
doc: inode uses a mutex instead of a semaphore.
uml: i386: Avoid redefinition of NR_syscalls
fix "seperate" typos in comments
cocbalt_lcdfb: correct sections
doc: Change urls for sparse
Powerpc: wii: Fix typo in comment
i2o: cleanup some exit paths
Documentation/: it's -> its where appropriate
UML: Fix compiler warning due to missing task_struct declaration
UML: add kernel.h include to signal.c
...
* anholt/drm-intel-next: (515 commits)
drm/i915: Fix out of tree builds
drm/i915: move fence lru to struct drm_i915_fence_reg
drm/i915: don't allow tiling changes on pinned buffers v2
drm/i915: Be extra careful about A/D matching for multifunction SDVO
drm/i915: Fix DDC bus selection for multifunction SDVO
drm/i915: cleanup mode setting before unmapping registers
drm/i915: Make fbc control wrapper functions
drm/i915: Wait for the GPU whilst shrinking, if truly desperate.
drm/i915: Use spatio-temporal dithering on PCH
[MTD] Remove zero-length files mtdbdi.c and internal.ho
pata_pcmcia / ide-cs: Fix bad hashes for Transcend and kingston IDs
libata: Fix several inaccuracies in developer's guide
slub: Fix bad boundary check in init_kmem_cache_nodes()
raid6: fix recovery performance regression
KEYS: call_sbin_request_key() must write lock keyrings before modifying them
KEYS: Use RCU dereference wrappers in keyring key type code
KEYS: find_keyring_by_name() can gain access to a freed keyring
ALSA: hda: Fix 0 dB for Packard Bell models using Conexant CX20549 (Venice)
ALSA: hda - Add quirk for Dell Inspiron 19T using a Conexant CX20582
ALSA: take tu->qlock with irqs disabled
...
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Perform graceful cleanup on errors instead of just bailing out.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move a number of #ifdefs from code into dss.h and elsewhere, and
conditionally define no-op static inline functions, cleaning up the
code. This style is according to Documentation/SubmittingPatches.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
The driver set the background color canvas but never writes it in
DISPC_DEFAULT_COLOR_m register, which changes the background color
on the LCD or TV.
This patch adds a line to call to dispc_set_default_color() which is
the function in charge to write the DISPC_DEFAULT_COLOR_m register.
Signed-off-by: Carlos Lopez <carlos.cruz@sasken.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
In DPLL4 M3, M4, M5 and M6 field width has been increased by 1 bit in 3630.
So the max divider value that can be achived will be 32 and not 16.
In 3630 the functional clock is x1 of DPLL4 and not x2. Hence multiplier 2
is removed.
Signed-off-by: Sudeep Basavaraj <sudeep.basavaraj@ti.com>
Signed-off-by: Mukund Mittal <mmittal@ti.com>
Signed-off-by: Kishore Y <kishore.y@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Tested on OMAP3EVM for OMAP3530 and AM/DM 3730.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
[tomi.valkeinen@nokia.com: added slab.h include]
[tomi.valkeinen@nokia.com: added dependency to BACKLIGHT_CLASS_DEVICE]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
If omapdss_dsi_display_enable() failed the DSI bus was left locked. Also
if the operation failed later omapdss_dsi_display_disable() would get
called without holding the bus lock.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
There are some strange problems with DSI and updates with odd widths. One
particular problem is that HS TX timeout triggers easily with updates with
odd widths.
This patch makes the updates widths even, circumventing the problem. There
should be no ill side effects with increasing the update area slightly to
make the width even.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Only call driver disable when device isn't already disabled, which also
handles the driver not loaded case.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
platform_enable/disable() is already called in venc_power_on/off(), so
don't do it again in venc_panel_enable/disable().
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Give up if lock_fb_info() fails, following the same convention as other
lock_fb_info() users.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Framebuffer ioctl processing forces lock_fb_info() -> omapfb_lock()
locking order. Follow that order to avoid possible circular locking
dependency, detected by lockdep.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
This patch enables the use of vdds_sdi regulator in SDI subsystem.
We can disable the vdds_sdi voltage when not in use to save
power.
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Panel enable/disable is now done via the panel driver, so we should not
call the panel driver again
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
This allows us to disable DPI on systems that do not have it
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
let vga16fb claim 0xA0000+0x10000 region as its aperture;
drm drivers don't use it, so we have to detect it and kick
vga16fb manually - but only if drm is driving the primary card
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Currently vesafb/efifb/... is kicked when hardware driver is registering
framebuffer. To do it hardware must be fully functional, so there's a short
window between start of initialisation and framebuffer registration when
two drivers touch the hardware. Unfortunately sometimes it breaks nouveau
initialisation.
Fix it by kicking firmware driver(s) before we start touching the hardware.
Reported-by: Didier Spaier <didier.spaier@epsm.fr>
Tested-by: Didier Spaier <didier.spaier@epsm.fr>
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It removes a hack from nouveau code which had to detect which
region to pass to kick vesafb/efifb.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds an argument to the DMAengine control function, so that
we can later provide control commands that need some external data
passed in through an argument akin to the ioctl() operation
prototype.
[dan.j.williams@intel.com: fix up some missed conversions]
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
