Commit Graph

4731 Commits

Author SHA1 Message Date
Larry Finger
a027087a6b rtl8187: Implement TX/RX blink for LED
The following patch implements some control over the LED on RTL8187B and
RTL8187L devices. Triggers are registered for TX and RX. Whenever the
trigger event occurs, the LED is turned off for 1/20 second, then turned
back on.

Note: For those RTL8187X devices that are built into the computer and have
a LED that is expected to be controlled with a radio switch, this patch will
not operate that LED. That will take a separate patch to be prepared later.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:57:16 -04:00
Marek Vasut
dc7d243d75 Add support for CF8381 WiFi card.
A detection function was added for identifying CF8381.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:57:15 -04:00
Christian Lamparter
fade5db4f2 p54: deactivate broken powersave function (part 2)
This patch deactivates powersave in station mode.

It does not work correctly yet, so the code does more harm than good.

(I split the original patch and sent part of it for 2.6.30, which didn't
have the IEEE80211_HW_BEACON_FILTER flag. -- JWL)

Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:57:15 -04:00
Luis R. Rodriguez
85efc86eb7 atheros: fix propagation of bad EEPROM on regulatory init
When the EEPROM is not in good condition we cannot continue so
we currently bail out but only ath5k is bailing out properly.
Both ath9k and ar9170 were proceeding and if a user were to run
into this they'd see an obscure panic. Lets propagate the error
as intended and make sure we inform the user by lifting the
error message from debug to a kernel error.

Stable note: You can find a port of this page here:

http://bombadil.infradead.org/~mcgrof/patches/ath9k/ath9k-fix-eeprom.patch.txt

Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:57:15 -04:00
Bob Copeland
26925042b6 ath5k: manipulate rxlink and descriptor address under rxbuf lock
Grabbing an ath5k_buf then dropping the lock is racy because the
referenced descriptor can be obtained in another thread and released
before the buffer is handed to the hardware.  Likewise, manipulating
sc->rxlink without the lock can lead to having multiple self-linked
hardware descriptors.

Changes-licensed-under: 3-Clause-BSD

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:57:15 -04:00
Bob Copeland
c57ca81576 ath5k: use rx hw descriptor pointer for self-linked check
This patch simplifies the code used to detect when the
self-linked DMA buffer is still in use by hardware, by
checking the hardware's rxdp register instead of looking
at the software buffer list.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:57:14 -04:00
Bob Copeland
46802a4f07 ath5k: use bool for modparams
Current code uses int types, but both modparams are boolean values.

Changes-licensed-under: 3-Clause-BSD

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:57:14 -04:00
Bob Copeland
56d2ac7638 ath5k: use tasklet_hi_schedule for beacon queue
For embedded platforms, beacon transmission can be starved when
flooded with data packets.  Prioritize beacons by giving the beacon
queue the first shot when the isr completes.

Changes-licensed-under: 3-Clause-BSD

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:57:14 -04:00
Bob Copeland
77ded01cc2 ath5k: fix initvals errors
This patch corrects a few errors in the initvals tables to match those
in the HAL tables.  Namely, remove a couple of repetitions, fix some
turbo mode errors, and correct a register for the CCK rate power table.

Changes-licensed-under: ISC

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:57:14 -04:00
Christian Lamparter
45f483c002 p54: remove module_ stubs
Christoph Hellwig pointed out that these stubs are unnecessary.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:57:14 -04:00
Vivek Natarajan
882b709230 ath9k: Disable autosleep feature for AR9285 based chipsets.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:57:14 -04:00
Christian Lamparter
a1c555802a ath: add module information
This patch adds licensing, author information and a description to the module.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:47 -04:00
Gábor Stefanik
06bfd0d3db rtl8187: Remove the "8187B chip detected" message when probing RTL8187B cards
This message appears to be nothing more than a leftover of the
experimental-8187B era. Also, we print the HW type in the hwaddr line,
making this message reduntant. And it's definitely not important
enough to be a KERN_WARNING.

Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:47 -04:00
Sujith
386aeacfa8 ath9k: Remove CHANNEL_CW_INT handling in ath9k_hw_calibrate
It is already handled properly in ath9k_hw_getnf.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:47 -04:00
Sujith
04d19ddd25 ath9k: Fix bug in calibration initialization
This patch fixes a bug in ath9k_hw_init_cal() where the wrong
calibration was being done for non-AR9285 chipsets.
Also add a few helpful comments.

Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:46 -04:00
Sujith
cbfe946860 ath9k: Use a consistent naming convention
This patch replaces old 'hal_' prefixes with 'ath9k_'.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:46 -04:00
Sujith
379f04407c ath9k: Cleanup calibration interface
This patch cleans up the functions dealing with calibration,
using proper return values.
ath9k_hw_per_calibration(), ath9k_hw_calibrate now return bool values
instead of setting error values in the function arguments.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:46 -04:00
Sujith
415f738ecf ath9k: Initialize ANI timers
The various ANI timers have to be initialized properly when
starting the calibration timer.

Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:46 -04:00
Sujith
a451aa66dc ath9k: Fix bug in determining calibration support
ADC gain calibration has to be done for all non 2GHZ-HT20 channels.
Regression from "ath9k: use ieee80211_conf on ath9k_hw_iscal_supported()"

Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:46 -04:00
Sujith
db2f63f60a ath9k: Fix bug in checking HT flag
The operating HT mode is stored in chanmode and
not channelFlags.

Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:46 -04:00
Sujith
822b0dfc13 ath9k: Remove unused channel flags
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:46 -04:00
Sujith
9c07a7777f ath9k: Fix bug in scan termination
A full HW reset needs to be done on termination of a scan run.
Not setting SC_OP_FULL_RESET resulted in doing a
fast channel change.

Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:46 -04:00
Sujith
675902ef82 ath9k: Fix memleak on TX DMA failure
The driver-specific region has to be freed in case
of a DMA mapping failure.

Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:46 -04:00
Sujith
d2f5b3a677 ath9k: Handle ASPM properly for RFKILL
Radio enable/disable have to handle ASPM state properly.
This patch fixes it.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:45 -04:00
Steven Luo
a89bff9a78 ath9k: reset after PCI FATAL/PERR interrupts
ath9k_hw_getisr() doesn't appear to set anything in the status mask for
PCI FATAL or PERR interrupts (AR_INTR_SYNC_HOST1_FATAL/PERR), which
the open-source HAL seems to do.  This means that the card isn't reset
after these interrupts.

This patch seems to fix a problem where the wireless drops out with an
"ath9k: received PCI FATAL interrupt" in dmesg after some time; the
hardware is an AR5416 in an ASUS WL-500W running 2.6.28.7 (OpenWRT) and
compat-wireless 2009-03-31.

Signed-off-by: Steven Luo <steven@steven676.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:45 -04:00
Larry Finger
2d1f96dd90 b43legacy: Clean up beacon IRQ
This patch ports commit c97a4ccc1f "b43: Fix beacon BH update" to
b43legacy. It fixes beacon updating in the bottomhalf. In case the device
is busy, we will defer to later in the IRQ handler.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Tested-by: David Ellingsworth <david@identd.dyndns.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:45 -04:00
Larry Finger
7858e07b7c b43legacy: Fixes for beaconing
This patch ports the beaconing fixes from commit a82d992261 "b43: Beaconing
fixes" to b43legacy. Basically it prevents the card from triggering the beacon
IRQ over and over again.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Tested-by: David Ellingsworth <david@identd.dyndns.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:45 -04:00
Christian Lamparter
4312a86b68 p54: remove obsolet signal quality calculation
The signal quality percentage is now calculated by mac80211 stack.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:45 -04:00
Christian Lamparter
6dfe9a884f p54: utilize all available key slots for decryption offload
This patch takes care of outstanding TODOs:
/* TODO: some devices have 4 more free slots for rx keys */

Now the driver can utilize all available key slots instead of just 4.
Obviously, this helps most in AP/IBSS(/MESH) mode, when
we have to use more different keys.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:45 -04:00
Michael Buesch
1379072877 b43: Remove unnecessary MMIO in interrupt hotpath
This removes unnecessary MMIO accesses in the interrupt hotpath.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:45 -04:00
John W. Linville
a2caba6b5f libertas: fix warning about %zd:
drivers/net/wireless/libertas/rx.c: In function ‘lbs_process_rxed_packet’:
drivers/net/wireless/libertas/rx.c:184: warning: format ‘%zd’ expects type ‘signed size_t’, but argument 4 has type ‘__le32’
drivers/net/wireless/libertas/rx.c:184: warning: format ‘%zd’ expects type ‘signed size_t’, but argument 5 has type ‘unsigned int’

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:44 -04:00
Wey-Yi Guy
a83b9141b5 iwlwifi: adding interrupt counter in debugfs for debugging
This patch adds interrupt statistics report to debugfs, this can help to
understand number of interrupts happened which including HW/SW error for
easier and better debugging.

in /sys/kernel/debug/ieee80211/phyN/iwlagn/data directory
use "cat interrupt" to view the current interrupt counter
use "echo 0 > interrupt" to clear interrupt counter

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:44 -04:00
Mohamed Abbas
1620108910 iwlcore: fix channel display in debugfs
Fix displaying of wrong channel information when user query
channel through debugfs

Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:44 -04:00
Daniel C Halperin
c2105fa7b6 iwlwifi: check triple_stream_basic_rates in iwl_full_rxon_required
For completeness, we should also make sure that the 3x3 MIMO rates are also checked when seeing if one rxon struct matches another.

Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:44 -04:00
Mohamed Abbas
3a6502927f iwlagn: Sync rxon active with changes
We need to sync rxon_active with changes after we commit rxon_assoc,
without rxon_active will still have the old data that cause
iwl_send_rxon_assoc to fail with no change in rxon command.

Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:44 -04:00
Daniel C Halperin
ddfcf99927 iwlwifi: do not set dual_stream_ant_msk for 3 streams
This patch fixes a bug introduced by commit "iwlwifi: adding MIMO3 support
in rate scaling". We should not set the dual_stream_ant_msk (for 2x2 MIMO)
when using a 3x3 rate, this will cause a SYSASSERT in uCode.

Note: there is no triple_stream_ant_msk, because all three antennas are used.

Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:43 -04:00
Wey-Yi Guy
12b9681721 iwlwifi: Display decoded rate/mcs information
This patch adding MCS information in rate_scale_table, it help for
debugging rate scaling algorithm, easy to understand what is the current
rate scale table and matching modulation, plus the last mcs used for tx.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:43 -04:00
Abhijeet Kolekar
bd564261d7 iwl3945: use iwl_mac_reset_tsf from iwlwifi
3945 can now use iwl_mac_reset_tsf from iwlwifi.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:43 -04:00
Abhijeet Kolekar
aa89f31e70 iwl3945: use iwl_mac_get_tx_stats from iwlwifi
3945 can now use iwl_mac_get_tx_stats from iwlwifi.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:43 -04:00
Abhijeet Kolekar
5ee5811e24 iwl3945: use iwl_mac_config_interface from iwlwifi
3945 can now use iwl_mac_config_interface from iwlwifi.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:43 -04:00
Abhijeet Kolekar
60690a6a38 iwlwifi: add config_ap lib op
add config_ap lib op to iwlwifi and iwl3945 in preparation
of future 3945 porting actions.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:43 -04:00
Abhijeet Kolekar
4808368dad iwl3945: use iwl_mac_config from iwlwifi
3945 can now use iwl_mac_config from iwlwifi

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:43 -04:00
Abhijeet Kolekar
d8052319f2 iwl3945: use iwl_mac_remove_interface from iwlwifi
3945 can now use iwl_mac_remove_interface from iwlwifi

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:43 -04:00
Abhijeet Kolekar
cbb6ab94b6 iwl3945: use iwl_mac_add_interface from iwlwifi
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:43 -04:00
Abhijeet Kolekar
727882d624 iwl3945: use iwl_set_mode in 3945
3945 can now use iwl_set_mode from iwlcore library.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:42 -04:00
Abhijeet Kolekar
4582353166 iwlwifi: add set_rxon_chain op
add set_rxon_chain op to iwlwifi cfg ops in preparation of
future 3945 porting work.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:42 -04:00
Abhijeet Kolekar
f5d3026683 iwl3945: use iwl_get_sta_id from iwlwifi
iwl3945 can now use iwl_get_sta_id.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:42 -04:00
Abhijeet Kolekar
06fd3d86a4 iwl3945/iwlwifi: unify add_station function
Patch unifies the add_station function for 3945 and iwlwifi drivers.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:42 -04:00
Abhijeet Kolekar
e11bc0286a iwlwifi: use station management ops
Patch replaces station management functions with ops declared.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:42 -04:00
Abhijeet Kolekar
40ace5b385 iwl3945: replace station function with station ops
Patch replaces station function used in driver by station management ops
in 3945.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:42 -04:00
Abhijeet Kolekar
79fa455a99 iwlwifi: add station management ops
This patch adds declarations for station management ops to iwlwifi drivers.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:42 -04:00
Abhijeet Kolekar
f45c271493 iwl3945: delay mode setting
Delay mode setting till uCode is ready.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:42 -04:00
Abhijeet Kolekar
e0158e6110 iwlwifi: add commit_rxon lib
Patch adds commit_rxon lib operation to iwlwifi and iwl3945 drivers.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:41 -04:00
Abhijeet Kolekar
9944b938f2 iwl3945: use iwl_mac_beacon_update
3945 can use iwl_mac_beacon_update.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:41 -04:00
Abhijeet Kolekar
5bbe233b9b iwl3945: use iwl_bss_info_changed
3945 can use iwl_bss_info_changed.
A new lib op is created for post_assoicate to distinguish between
3945 and iwlwifi's post_associate operations.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:41 -04:00
Bing Zhao
e45d8e534b libertas: add support for Marvell SD8688 chip
libertas: add support for Marvell SD8688 chip

Use RxPD->pkt_ptr to locate eth803 header in the packet
received since SD8688/v10 firmware allows a gap between
RxPD and eth803 header.

Set SDIO block size to 256 for CMD53.
The maximum block size for SD8688 WLAN function is set
to 512 in TPLFE_MAX_BLK_SIZE. But using 512 as block size
results upto 2K bytes data (4 blocks) being transferred
and causes buffer overflow in firmware.

Both changes above are backward compatible with earlier
firmware versions for SD8385/SD8686.

The SDIO_DEVICE_IDs for SD8688 chip are added in
include/linux/mmc/sdio_ids.h

Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:41 -04:00
Max Filippov
87cbfd0688 p54spi: get rid of busy-wait loops
p54spi_wakeup and p54spi_tx_frame used busy-waiting loop
to poll for 'ready' bits in SPI_ADRS_HOST_INTERRUPTS register.
With this change in place 'WR_READY timeout' messages do not
show anymore.

Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:41 -04:00
Bob Copeland
6a362bb1c9 ath5k: add support for Fukato Datacask Jupiter LEDs
This adds support for the LEDs on the Jupiter netbook.

Reported-by: Martin Bammer <mrb74@gmx.at>

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:41 -04:00
Anna Neal
b26ed97c75 libertas: increase spi driver thread priority
Currently, the libertas main thread contends with the spi driver thread
in the TX path.  To improve throughput, ensure that the driver thread
has higher scheduling priority than the libertas main thread.  Do this
by making the libertas spi driver thread a low priority real time
thread.

We measured an average throughput improvement of 13%.

Signed-off-by: Anna Neal <anna@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:41 -04:00
Wey-Yi Guy
3eb9296970 iwlwifi: add debug messages when start aggregation queue
This patch adding few more debug messages if encounter error when driver
try to start tx aggregation queue. Also change from IWL_ERR to
IWL_DEBUG_HT is the HW legacy queue is empty when driver request to move
to aggregation queue.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:40 -04:00
Wey-Yi Guy
584a0f0063 iwlwifi: adding MIMO3 support in rate scaling
Separated the MIMO tpt matrix into MIMO2 and MIMO3, adding MIMO3 support
in rate scaling algorithm. If the device support 3x3, then utilize all
three antenna (A/B/C) for tx to improve throughput.

Adding rs_switch_to_mimo3() function to allow switch to mimo3 modulation
mode from other modes(legacy/siso/mimo2). Adding rs_move_mimo3_to_other()
function to allow switch from mimo3 modulation mode to either siso or mimo2;
also support toggle between SGI and NGI.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:40 -04:00
Wey-Yi Guy
11397a656f iwlwifi: adding triple stream rate support for MIMO3
Adding ht triple_stream_basic_rates for MIMO3 supports

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:40 -04:00
Fabio Rossi
64cdb0e3b8 ath5k: fix interpolation with equal power levels
When the EEPROM contains weird values for the power levels we have to
fix the interpolation process.

Signed-off-by: Fabio Rossi <rossi.f@inwind.it>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:40 -04:00
Larry Finger
910cfee363 b43legacy: Do not select HW_RANDOM
Auto-depend on HW_RANDOM, rather than "select"ing it.
This way the user has the choice to enable or disable HWRNG support.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:40 -04:00
Johannes Berg
18a8365992 cfg80211: introduce scan IE limit attribute
This patch introduces a new attribute for a wiphy that tells
userspace how long the information elements added to a probe
request frame can be at most. It also updates the at76 to
advertise that it cannot support that, and, for now until I
can fix that, iwlwifi too.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:39 -04:00
Luis R. Rodriguez
75c2148fa5 ath5k: sparse fix ath5k_led_on needs to be static
drivers/net/wireless/ath/ath5k/led.c:81:6: warning:
symbol 'ath5k_led_on' was not declared. Should it be static?

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:39 -04:00
Luis R. Rodriguez
6b2b2ffbef ath: space cleanup
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:38 -04:00
Luis R. Rodriguez
203c4805e9 atheros: put atheros wireless drivers into ath/
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:38 -04:00
Christian Lamparter
1878f77e13 Make ar9170 use common ath reg code
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:37 -04:00
Bob Copeland
f769c36bd7 ath5k: use regulatory infrastructure
Make ath5k select the ath module and add in the hooks to make the
eeprom regulatory hint and reg notifier take effect.

Changes to attach.c
Changes-licensed-under: ISC

Changes to base.c
Changes-licensed-under: 3-Clause-BSD

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:37 -04:00
Bob Copeland
e3bb249be8 ath: move more setup code into ath_regd_init
Setup the wiphy regulatory parameters when first initializing the
Atheros regulatory module.  We can remove five exported symbols this
way and simplify the driver code for both ath5k and ath9k.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:37 -04:00
Bob Copeland
3a702e49c0 atheros: introduce ath module containing common ath5k/ath9k/ar9170 code
This change creates a new module, ath.ko, which includes code that can
be shared between ath5k, ath9k and ar9170. For now, extract most of the ath9k
regulatory code so it can also be used in ath5k.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:37 -04:00
Bob Copeland
c02cf3738c ath9k: pass regd structure directly to regulatory functions
All regulatory information is encapsulated by the ath9k_regulatory
struct, so we can now change all the callers to take that directly
instead of struct ath_hw.  This in turn will enable us to move the
regulatory functions to common code also used by ath5k, since both
can use this regulatory struct.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:37 -04:00
Bob Copeland
fc2ada30ca ath9k: separate ath9k specific code from ath9k_regd_get_ctl()
Until ath5k and ath9k share common channel structures, they will have
to implement their own get_ctl() function.  Split out the portion that
only relies on the current band and reg domain so that it can be common
code.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:37 -04:00
Reinette Chatre
55a3757a57 iwlwifi: change check triggering device restart after rfkill change
The STATUS_ALIVE value cannot be used because it is cleared when
interface is brought down and will not be set if rfkill is enabled when
interface is started again. The interface can thus not be brought up if
rfkill was enabled before stopping the interface and disabled after
starting the interface.

Change the test to use priv->is_open instead, this will be set when
interface is started whether rfkill is enabled or not.

Thanks to Helmut Schaa for the suggested fix.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:37 -04:00
Jussi Kivilinna
71a7b26d3e rndis_wlan: convert scan to cfg80211
Convert scan function to cfg80211. Unlike old scan code new code
waits 1 sec before getting scan data from device and passing
forward to cfg80211.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:36 -04:00
Jussi Kivilinna
4d2a369ec0 rndis_wlan: convert get range to cfg80211
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:36 -04:00
Jussi Kivilinna
4bd7f03e91 rndis_wlan: change quality level scale
Change quality level scale to match cfg80211 CFG80211_SIGNAL_TYPE_UNSPEC.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:36 -04:00
John W. Linville
964c1d417e rndis_wlan: convert get/set mode to cfg80211
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[edit: made rndis_change_virtual_intf static]
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:36 -04:00
John W. Linville
5c8fa4f7e7 rndis_wlan: initiate cfg80211 conversion
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:36 -04:00
Christian Lamparter
f13027af5c p54: add beacon filtering support
This patch adds beacon filtering support to p54.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:36 -04:00
Christian Lamparter
dce072580e p54: more SoftLED updates
This patch hopefully finishes the SoftLED code:
- It adds two more LEDs (rx and radio).
  (the FW claims it can support up to 16 LEDs,
   but I doubt that any vendor put more than 4 on a board)
- update the LEDs in a _delayed_ workqueue.
  No one reported any more crashes.
  (see: "PATCH] p54: fix race condition in memory management")
  So we can stop burning the mm code.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:36 -04:00
Christian Lamparter
cf3a9579f6 p54: clean up p54.h's struct p54_common
This patch rearrange and regroups most elements in p54_common.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:36 -04:00
Bob Copeland
42639fcd44 ath5k: reduce exported channel list
Claiming every available 5 ghz channel has a couple of negative
side-effects: scanning takes a long time, and the channel list
overflows the available buffer space for netlink commands,
resulting in:

    $ iw phy phy0 info
    command failed: No buffer space available (-105)

This patch adds a modparam so people who want to see all the channels
can do so by passing all_channels=1.  By default users will see a
smaller list of channels.  This also halves scan time, from 10 seconds
down to less than 5 when using world regulatory.

Changes-licensed-under: 3-Clause-BSD

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Reported-by: Simon Farnsworth <simon@farnz.org.uk>
Tested-By: Simon Farnsworth <simon@farnz.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:35 -04:00
Sujith
f5c38ef06e ath9k: Fix bug in determining HT40 mode
This patch fixes a bug in checking for HT40 mode.
The STA's mode can be determined from the cached HT capabilities,
use that and remove the redundant variable 'rc_phy_mode'.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:35 -04:00
Sujith
c6483cfe71 ath9k: Determine number of streams from HT capabilities
The number of streams supported by a STA can be determined
directly from the HT capabilities. Remove the redundant
variable storing the stream cap.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:35 -04:00
Sujith
063d8be37d ath9k: Clean Interrupt handling routine
This patch cleans up the ISR, removing a unnecessary do..while
loop, and waking up the chip before getting the pending
interrupts.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:35 -04:00
Sujith
87792efc7d ath9k: Trivial fix to handle AMPDU params properly
Handle aggregation params only when aggregation is
supported.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:35 -04:00
Sujith
1ffb0610be ath9k: Initialize values when setting up the queue parameters
Also fix a small typo.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:35 -04:00
Sujith
797fe5cbef ath9k: Remove the useless do..while loops
These are unnecessary constructs in a function.
This patch removes these from both RX and TX init
routines.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:35 -04:00
Sujith
4658b98517 ath9k: Remove TIM from the interrupt mask
We never handle TIM, TIM_TIMER is used instead.
Remove this and the unnecessary swBeaconProcess variable.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:34 -04:00
Sujith
7dd5874859 ath9k: Check for root debugfs file
Creation of the root debugfs file could have failed
for some reason, check properly before proceeding in this
case.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:34 -04:00
Sujith
5cc93992cc ath9k: Remove unused structures
struct aggr_rifs_param and ath_tx_stat are not used anywhere.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:34 -04:00
Sujith
ae459af128 ath9k: Remove a couple of unused variables in descriptor handling
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:34 -04:00
Sujith
a119cc492f ath9k: Cleanup buffer status handling
Using a u32 to store a single flag is overkill.
Use a bool to store whether the buffer is stale or not.
Also, use u8 instead of u32 to store the buffer type.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:33 -04:00
Sujith
a22be22ab8 ath9k: Avoid unneeded casts
Change the void pointer to struct sk_buff and access
bf_mpdu directly, removing all casts in the process.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:32 -04:00
Sujith
0ef1f168b6 ath9k: Remove redundant variable for Interrupt Mitigation
The state is already stored in ath9k_ops_config, so remove
the duplicate variable in ath_hw.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:30 -04:00
Sujith
eef7a57430 ath9k: Change return value of ath9k_hw_fill_cap_info
This routine always return true, checking for false
in the return value is invalid. Fix this.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:30 -04:00
Sujith
d8baa93926 ath9k: Cleanup debug messages
Clean debug messages to use appropriate levels,
remove useless messages, and trim the number of
debug levels.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:30 -04:00
Sujith
6ed6a05e5c ath9k: Remove redundant chainmask check
We get the valid chainmasks on HW attach, checking
it again during reset is redundant. This patch removes the check.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:29 -04:00
Sujith
bdbdf46daa ath9k: Remove a few unused flags
This patch removes unused HW capability flags and
HW operation variables, and a chainmask flag that
we don't use anywhere.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:29 -04:00
Vivek Natarajan
8782b41d13 ath9k: No need to abort Rx path when autosleep is enabled.
For chipsets supporting autosleep feature, there is no need to abort
Rx engine since they are capable of automatically going back to sleep
after receiving a packet.

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:29 -04:00
Michael Buesch
616de35da9 b43: Do not "select" HW_RANDOM
Auto-depend on HW_RANDOM, rather than "select"ing it.
This way the user has the choice to enable or disable HWRNG support.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:29 -04:00
Ivo van Doorn
a57e2e84b6 rt2x00: Fix Sparse warning
rt2x00link_reset_qual() is not declared in a header,
and is only internally used within rt2x00link.c.
It should be declared as static.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:29 -04:00
Ivo van Doorn
440ddadaee rt2x00: Move Move pci_dev specific access to rt2x00pci
pci_dev->irq and pci_name(pci_dev) access should be limited
to rt2x00pci only. This is more generic and allows a rt2x00 pci
driver to be controlled as PCI device but also as platform driver
(needed for rt2800pci SoC support).

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:29 -04:00
Christian Lamparter
32c1628f15 ar9170: fix hang on stop
This patch fixes a locking problem which freezes the network core.

The deadlock goes as follows:
- ar9170_op_stop - is called
1. change the state to IDLE
2. > take the MUTEX <
3. cancel_SYNC all pending work, which means
    "block until a work_struct's callback has terminated"
=>  if filter_config_work was queued it tries to get the MUTEX,
       before checking the device state...

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:29 -04:00
Pavel Roskin
807e37394b ath5k: fix scanning in AR2424
AR5K_PHY_PLL_40MHZ_5413 should not be ORed with AR5K_PHY_MODE_RAD_RF5112
for 5 GHz channels.

The incorrect PLL value breaks scanning in the countries where 5 GHz
channels are allowed.

Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:29 -04:00
Johannes Berg
621cac8529 rfkill: remove user_claim stuff
Almost all drivers do not support user_claim, so remove it
completely and always report -EOPNOTSUPP to userspace. Since
userspace cannot really drive rfkill _anyway_ (due to the
odd restrictions imposed by the documentation) having this
code is just pointless.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:27 -04:00
Max Filippov
9f201a8783 p54spi: compensate firmware alignment bug in p54spi_rx
Firmware may insert up to 4 padding bytes after the lmac header,
but it does not amend the size of SPI data transfer.
Such packets has correct data size in header, thus referencing
past the end of allocated skb. Put extra 4 bytes to the end of the
received skb to compensate for this case.

Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:27 -04:00
Abhijeet Kolekar
488829f1b1 iwl3945: use iwl_mac_conf_tx
3945 now uses iwl_mac_conf_tx.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:27 -04:00
Wey-Yi Guy
6da3a13e4f iwlwifi: merge and better support of suspend/resume for iwlagn and iwl3945
With mac80211's help to call stop() and start() in mac80211
suspend/resume function, both iwlagn and iwl3945 no longer calling
stop() and start(); remove un-necessary STATUS_IN_SUSPEND bit from both
header files and functions,

Move apm_ops.stop() function into pci_suspend() to ensure
DMA is stopped before go into suspend mode.

iwl3945 has the similar suspend/resume function as iwlagn, so move both
functions to iwlcore to be shared by both drivers.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:27 -04:00
Max Filippov
4f5cab969b p54spi: fix p54spi_tx_frame DMA transfer initiation and skb cleanup
p54spi_tx_frame wasn't waiting for HOST_ALLOWED in SPI_ADRS_DMA_WRITE_CTRL.
This resulted in frequent 'WR_READY timeout' on beacon resubmission.

Also don't free skb on error path, as it gets freed on p54spi_wq_tx.

Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:27 -04:00
Bing Zhao
684d6b3602 libertas: support mesh for various firmware versions
CMD_MESH_CONFIG command ID and a couple of structure members in TxPD,
RxPD have been changed in firmware version 10.x.y.z and newer.

Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:26 -04:00
Max Filippov
5e3af1d2d3 p54spi: fix p54spi_upload_firmware
Instead of firmware itself p54_upload_firmware was sending to the device
content of struct firmware and the following random garbage.

Notice '&' before priv->firmware->data at p54spi_spi_write.
But simple removing of '&' sign triggered BUG_ON at dma_cache_maint.
Thus kmemdup - kfree workaround.

Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:26 -04:00
Max Filippov
f74d0f5cac p54spi: mask value read from SPI_ADRS_DMA_WRITE_CTRL in p54spi_wait_bit
Mask value read from SPI_ADRS_DMA_WRITE_CTRL in p54spi_wait_bit.
 Without this, 'fw_upload not allowed to DMA write' is observed at both N800 and N810.

Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:26 -04:00
Reinette Chatre
df833b1d73 iwlwifi: DMA fixes
A few issues wrt DMA were uncovered when using the driver with swiotlb.
- driver should not use memory after it has been mapped
- iwl3945's RX queue management cannot use all of iwlagn because
  the size of the RX buffer is different. Revert back to using
  iwl3945 specific routines that map/unmap memory.
- no need to "dma_syn_single_range_for_cpu" followed by pci_unmap_single,
  we can just call pci_unmap_single initially
- only map the memory area that will be used by device. this is especially
  relevant to the mapping of iwl_cmd. we should not map the entire
  structure because the meta data at the beginning of structure contains
  the address to be used later for unmapping. If the address to be used for
  unmapping is stored in mapped data it creates a problem.
- ensure that _if_ memory needs to be modified after it is mapped that we
  call _sync_single_for_cpu first, and then release it back to device with
  _sync_single_for_device
- we mapped the wrong length of data for host commands, with mapped length
  differing with length provided to device, fix that.

Thanks to Jason Andryuk <jandryuk@gmail.com> for significant bisecting
help to find these issues.

This fixes http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1964

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Jason Andryuk <jandryuk@gmail.com>
Tested-by: Ben Gamari <bgamari@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-21 16:43:34 -04:00
Reinette Chatre
d2ee9cd2e2 iwlwifi: add debugging for TX path
When debugging TX issues it is helpful to know the seq nr of the
frame being transmitted. The seq nr is printed as part of ucode's
log informing us which frame is being processed. Having this information
printed in driver log makes it easy to match activities between driver
and firmware.

Also make possible to print TX flags directly. These are already printed
as part of entire TX command, but having it printed directly in cpu format
makes it easier to look at.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-21 16:43:34 -04:00
Rami Rosen
c491bf1205 mwl8: fix build warning.
This patch fixes a build warning in mwl8.c.
(Marvell TOPDOG wireless driver)

The warning it fixes is: "large integer implicitly truncated to unsigned type."

The rx_ctrl member of the mwl8k_rx_desc struct is 8 bit (__u8 ), whereas trying
to assign it a 32 bit value (which is returned from  cpu_to_le32())
causes the compiler to issue
a truncation warning.

Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-21 16:43:33 -04:00
Reinette Chatre
71d449b55a iwl3945: use cancel_delayed_work_sync to cancel rfkill_poll
Users reported lockup with work still trying to run
after module has been unloaded.

http://thread.gmane.org/gmane.linux.kernel.wireless.general/30594/focus=30601

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reported-by: TJ <ubuntu@tjworld.net>
Reported-by: Huaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-21 16:43:32 -04:00
Jay Sternberg
4b6f764e14 iwlwifi: fix EEPROM validation mask to include OTP only devices
Fix the bug where some revisions of 6000 series hardware cannot
be used. Later versions of 6000 series have the EEPROM replaced by
OTP. For these devices to be used we need to expand valid EEPROM mask.

Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-21 16:43:30 -04:00
Johannes Berg
1bb593801e atmel: fix netdev ops conversion
sparse says:

drivers/net/wireless/atmel.c:1501:3: warning: Initializer entry defined twice
drivers/net/wireless/atmel.c:1505:3:   also defined here

and it's correct; atmel has its own ndo_change_mtu and
shouldn't use eth_change_mtu.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-21 02:08:51 -07:00
David S. Miller
e5e9743bb7 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	net/core/dev.c
2009-04-21 01:32:26 -07:00
Christian Lamparter
e10a9dfc35 ar9170usb: fix hang on resume
This patch fixes a hang on resume when the filesystem is not
available and request_firmware blocks.

However, the device does not accept the firmware on resume.
and it will exit with:

> firmware part 1 upload failed (-71).
> device is in a bad state. please reconnect it!

Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-20 16:36:26 -04:00
Joerg Albert
230f7af0d8 mwl8k: fix module re-insertion bug
swap mwl8k_remove and mwl8k_shutdown functions to allow
"rmmod mwl8k; modprobe mwl8k"

Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-20 16:36:26 -04:00
Christian Lamparter
c3b93c878d p54: deactivate broken powersave function
This patch deactivates powersave in station mode.

It does not work correctly yet, so the code does more harm than good.

Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-20 16:36:26 -04:00
Joe Perches
125143966f iwl3945-base.c: Add missing space to debug print
"not" is not printed without a space after %pM

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-20 16:36:26 -04:00
Ivo van Doorn
499a214ca2 rt2x00: Don't free register information on suspend
After suspend & resume the rt2x00 devices won't wakeup
anymore due to a broken register information setup.
The most important problem is the release of the EEPROM
buffer which is completely cleared and never read again
after the suspend.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-20 16:36:26 -04:00
Christian Lamparter
957b0516f7 ar9170usb: add ZyXEL NWD271N
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-17 15:27:14 -04:00
Johannes Berg
1269fa737f ar9170: fix struct layout on arm
arm will pad even between u8's, so mark the structs/unions
packed. Fixes a build bug on arm due to BUILD_BUG_ON tests
in the code.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-16 10:39:17 -04:00
Pavel Roskin
91fe9ca74e orinoco: correct timeout logic in __orinoco_hw_set_tkip_key()
If the value read from HERMES_RID_TXQUEUEEMPTY becomes 0 after exactly
100 readings, we wrongly consider it a timeout.  Rewrite the clever
while loop as a for loop that does the right thing and looks simpler.

Reported by Juha Leppanen <juha_motorsportcom@luukku.com>

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-16 10:39:17 -04:00
Herton Ronaldo Krzesinski
f05faa31c3 rt2x00: prevent double kfree when failing to register hardware
In a scenario where there isn't any firmware available, we will have a
double kfree of rt2x00dev->spec.channels_info when ieee80211_register_hw
returns an error status inside rt2x00lib_probe_hw.

The problem is that if ieee80211_register_hw fails, we call
rt2x00lib_remove_hw twice:
* first inside rt2x00lib_probe_hw upon failure of ieee80211_register_hw
* error status is returned to rt2x00lib_probe_dev, which then sees it and
  calls in this case rt2x00lib_remove_dev that will again run
  rt2x00lib_remove_hw

Prevent this avoiding calling rt2x00lib_remove_hw inside
rt2x00lib_probe_hw

Problem was detected with CONFIG_DEBUG_PAGEALLOC=y, CONFIG_SLUB_DEBUG=y,
CONFIG_SLUB_DEBUG_ON=y, that dumps this with no firmware available:

rt61pci 0000:00:07.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
wmaster0 (rt61pci): not using net_device_ops yet
phy0: Selected rate control algorithm 'pid'
phy0: Failed to initialize wep: -2
phy0 -> rt2x00lib_probe_dev: Error - Failed to initialize hw.
=============================================================================
BUG kmalloc-128: Object already free
-----------------------------------------------------------------------------

INFO: Allocated in rt61pci_probe_hw+0x3e5/0x6e0 [rt61pci] age=340 cpu=0 pid=21
INFO: Freed in rt2x00lib_remove_hw+0x59/0x70 [rt2x00lib] age=0 cpu=0 pid=21
INFO: Slab 0xc13ac3e0 objects=23 used=10 fp=0xdd59f6e0 flags=0x400000c3
INFO: Object 0xdd59f6e0 @offset=1760 fp=0xdd59f790

Bytes b4 0xdd59f6d0:  15 00 00 00 b2 8a fb ff 5a 5a 5a 5a 5a 5a 5a 5a ....².ûÿZZZZZZZZ
  Object 0xdd59f6e0:  6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
  Object 0xdd59f6f0:  6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
  Object 0xdd59f700:  6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
  Object 0xdd59f710:  6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
  Object 0xdd59f720:  6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
  Object 0xdd59f730:  6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
  Object 0xdd59f740:  6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
  Object 0xdd59f750:  6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b a5 kkkkkkkkkkkkkkk¥
 Redzone 0xdd59f760:  bb bb bb bb                                     »»»»
 Padding 0xdd59f788:  5a 5a 5a 5a 5a 5a 5a 5a                         ZZZZZZZZ
Pid: 21, comm: stage1 Not tainted 2.6.29.1-desktop-1.1mnb #1
Call Trace:
 [<c01abbb3>] print_trailer+0xd3/0x120
 [<c01abd37>] object_err+0x37/0x50
 [<c01acf57>] __slab_free+0xe7/0x2f0
 [<c01ad1de>] kfree+0x7e/0xd0
 [<e0e4a239>] ? rt2x00lib_remove_hw+0x59/0x70 [rt2x00lib]
 [<e0e4a239>] ? rt2x00lib_remove_hw+0x59/0x70 [rt2x00lib]
 [<e0e4a239>] rt2x00lib_remove_hw+0x59/0x70 [rt2x00lib]
 [<e0e4acc7>] rt2x00lib_remove_dev+0x37/0x50 [rt2x00lib]
 [<e0e4b087>] rt2x00lib_probe_dev+0x1a7/0x3b0 [rt2x00lib]
 [<e0eb288f>] rt2x00pci_probe+0xdf/0x1ee [rt2x00pci]
 [<c026b9ee>] local_pci_probe+0xe/0x10
 [<c026c750>] pci_device_probe+0x60/0x80
 [<c02d5c2a>] driver_probe_device+0x9a/0x2e0
 [<c02d5ef9>] __driver_attach+0x89/0x90
 [<c02d541b>] bus_for_each_dev+0x4b/0x70
 [<c026c690>] ? pci_device_remove+0x0/0x40
 [<c02d59d9>] driver_attach+0x19/0x20
 [<c02d5e70>] ? __driver_attach+0x0/0x90
 [<c02d4cef>] bus_add_driver+0x1cf/0x2a0
 [<c026c690>] ? pci_device_remove+0x0/0x40
 [<c02d60c9>] driver_register+0x69/0x140
 [<c026c9b0>] __pci_register_driver+0x40/0x80
 [<e0ecc000>] ? rt61pci_init+0x0/0x19 [rt61pci]
 [<e0ecc017>] rt61pci_init+0x17/0x19 [rt61pci]
 [<c0101116>] do_one_initcall+0x26/0x1c0
 [<c01ab90c>] ? slab_pad_check+0x3c/0x120
 [<c01ab90c>] ? slab_pad_check+0x3c/0x120
 [<c01ac8da>] ? check_object+0xda/0x210
 [<c01b0026>] ? percpu_free+0x46/0x50
 [<c01ad09e>] ? __slab_free+0x22e/0x2f0
 [<c01b0026>] ? percpu_free+0x46/0x50
 [<c01b0026>] ? percpu_free+0x46/0x50
 [<c01b0026>] ? percpu_free+0x46/0x50
 [<c01687ec>] ? stop_machine_destroy+0x3c/0x40
 [<c015e515>] ? load_module+0xa5/0x1c50
 [<e0ec5000>] ? rt61pci_eepromregister_read+0x0/0x40 [rt61pci]
 [<e0eb2000>] ? rt2x00pci_write_tx_data+0x0/0x90 [rt2x00pci]
 [<c03ac2fb>] ? mutex_lock+0xb/0x20
 [<c03ac2fb>] ? mutex_lock+0xb/0x20
 [<c017ad16>] ? tracepoint_update_probe_range+0x76/0xa0
 [<c017ad6f>] ? tracepoint_module_notify+0x2f/0x40
 [<c03b02ed>] ? notifier_call_chain+0x2d/0x70
 [<c014f0ed>] ? __blocking_notifier_call_chain+0x4d/0x60
 [<c014f11a>] ? blocking_notifier_call_chain+0x1a/0x20
 [<c0160156>] sys_init_module+0x96/0x1d0
 [<c019dad6>] ? sys_munmap+0x46/0x60
 [<c0105546>] syscall_call+0x7/0xb
FIX kmalloc-128: Object at 0xdd59f6e0 not freed
rt61pci 0000:00:07.0: PCI INT A disabled
rt61pci: probe of 0000:00:07.0 failed with error -2

Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-16 10:39:15 -04:00
Johannes Berg
d60cc91acd fix iwl3945 registration regression
I forgot that iwl3945 registration is separate from iwlagn.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-16 10:39:15 -04:00
Michael Buesch
591f3dc200 b43: Do radio lock assertion in software
The assertion of the lock-bit in the hardware register is unreliable,
because there are devices with quirks that will randomly set the bit.

Do the assertion in software, only.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-16 10:39:14 -04:00
Ivo van Doorn
6aabd4c444 rt2x00: Add rt73usb USB IDs
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-16 10:39:13 -04:00
Christian Lamparter
e3062403f5 p54usb: add Telsey 802.11g USB2.0 Adapter
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-16 10:39:12 -04:00
Christian Lamparter
4fc298b866 ar9170: add Cace Airpcap NX usb_id
This patch adds a new device to ar9170usb.

Reported-by: Mike Kershaw/Dragorn <dragorn@kismetwireless.net>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-16 10:39:12 -04:00
Dan Williams
011f5c5bb2 airo: queue SIOCSIWAUTH-requested auth mode change for next commit
Code was clearly wrong, plus callers expect the mode change to happen as
soon as possible, not dropped on the floor until the next time some
other config value changes and a commit happens.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-16 10:39:10 -04:00
Jamie Lentin
02a9a39294 at76c50x-usb: Add device ID for OQO model 01+
Add USB device ID for OQO 01+'s internal wireless LAN

An OQO employee mentions the chip's true identity here:-
    ftp://ftp.oqo.com/unsupported/linux/OQOLinux.html

Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-16 10:39:09 -04:00
Philip Rakity
f54930f363 libertas: don't leak skb on receive error
Don't lead memory when receive errors

Signed-off-by: Philip Rakity <prakity@yahoo.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-16 10:39:08 -04:00
Pavel Roskin
853da11b94 ath9k: fix access to a freed skb in ath_rx_tasklet()
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-16 10:39:07 -04:00
Christian Lamparter
731c653168 p54spi: fix locking warning in p54spi_op_tx
This patch fixes the following waring:
> ------------[ cut here ]------------
>WARNING: at kernel/softirq.c:138 local_bh_enable+0x54/0xbc()
>Modules linked in: p54spi
>[<c0034ff8>] (dump_stack+0x0/0x14)
>[<c005b1a4>] (warn_on_slowpath+0x0/0x68)
>[<c00604c8>] (local_bh_enable+0x0/0xbc)
>[<bf000000>] (p54spi_op_tx+0x0/0x4c [p54spi])
>[<c01a4d34>] (p54_sta_unlock+0x0/0x78)

p54spi_op_tx needs to be called from different locking contexts.
Therefore we have to protect the linked list with irqsave spinlocks.

Reported-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-16 10:39:06 -04:00
Christian Lamparter
540828196e p54: replace MAC80211_LEDS with P54_LEDS in p54.h
I'm very sorry, as this change belongs to the other patch:
"[PATCH] p54: fix SoftLED compile dependencies".
however I must have somehow lost "git add" for that file.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-16 10:39:04 -04:00
Michael Buesch
cf68636a97 b43: Refresh RX poison on buffer recycling
The RX buffer poison needs to be refreshed, if we recycle an RX buffer,
because it might be (partially) overwritten by some DMA operations.

Cc: stable@kernel.org
Cc: Francesco Gringoli <francesco.gringoli@ing.unibs.it>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-16 10:39:03 -04:00
Michael Buesch
ec9a1d8c13 b43: Poison RX buffers
This patch adds poisoning and sanity checking to the RX DMA buffers.
This is used for protection against buggy hardware/firmware that raises
RX interrupts without doing an actual DMA transfer.

This mechanism protects against rare "bad packets" (due to uninitialized skb data)
and rare kernel crashes due to uninitialized RX headers.

The poison is selected to not match on valid frames and to be cheap for checking.

The poison check mechanism _might_ trigger incorrectly, if we are voluntarily
receiving frames with bad PLCP headers. However, this is nonfatal, because the
chance of such a match is basically zero and in case it happens it just results
in dropping the packet.
Bad-PLCP RX defaults to off, and you should leave it off unless you want to listen
to the latest news broadcasted by your microwave oven.

This patch also moves the initialization of the RX-header "length" field in front of
the mapping of the DMA buffer. The CPU should not touch the buffer after we mapped it.

Cc: stable@kernel.org
Reported-by: Francesco Gringoli <francesco.gringoli@ing.unibs.it>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-16 10:39:03 -04:00
Alexander Beregalov
d130fe5c95 ipw2x00: remove old compat_net_dev_ops code
Since both ipw2100 and ipw2200 are already converted to new
net_device_ops this code is useless.

Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-16 02:20:04 -07:00
Alexander Beregalov
0ee904c35c drivers/net: replace BUG() with BUG_ON() if possible
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-13 15:44:36 -07:00
Wei Yongjun
54cb2284dc at76c50x-usb: remove pointless conditional before kfree_skb()
Remove pointless conditional before kfree_skb().

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-13 15:44:35 -07:00
Yang Hongyang
e930438c42 Replace all DMA_nBIT_MASK macro with DMA_BIT_MASK(n)
This is the second go through of the old DMA_nBIT_MASK macro,and there're not
so many of them left,so I put them into one patch.I hope this is the last round.
After this the definition of the old DMA_nBIT_MASK macro could be removed.

Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Greg KH <greg@kroah.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-13 15:04:33 -07:00
Yang Hongyang
28b7679677 dma-mapping: replace all DMA_30BIT_MASK macro with DMA_BIT_MASK(30)
Replace all DMA_30BIT_MASK macro with DMA_BIT_MASK(30)

Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07 08:31:11 -07:00
Yang Hongyang
284901a90a dma-mapping: replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)

Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07 08:31:11 -07:00
Yang Hongyang
6a35528a83 dma-mapping: replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)

Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07 08:31:10 -07:00
Linus Torvalds
811158b147 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
  trivial: Update my email address
  trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
  trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
  trivial: Fix misspelling of "Celsius".
  trivial: remove unused variable 'path' in alloc_file()
  trivial: fix a pdlfush -> pdflush typo in comment
  trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
  trivial: wusb: Storage class should be before const qualifier
  trivial: drivers/char/bsr.c: Storage class should be before const qualifier
  trivial: h8300: Storage class should be before const qualifier
  trivial: fix where cgroup documentation is not correctly referred to
  trivial: Give the right path in Documentation example
  trivial: MTD: remove EOL from MODULE_DESCRIPTION
  trivial: Fix typo in bio_split()'s documentation
  trivial: PWM: fix of #endif comment
  trivial: fix typos/grammar errors in Kconfig texts
  trivial: Fix misspelling of firmware
  trivial: cgroups: documentation typo and spelling corrections
  trivial: Update contact info for Jochen Hein
  trivial: fix typo "resgister" -> "register"
  ...
2009-04-03 15:24:35 -07:00
Linus Torvalds
15f7176eb1 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  wireless: remove duplicated .ndo_set_mac_address
  netfilter: xtables: fix IPv6 dependency in the cluster match
  tg3: Add GRO support.
  niu: Add GRO support.
  ucc_geth: Fix use-after-of_node_put() in ucc_geth_probe().
  gianfar: Fix use-after-of_node_put() in gfar_of_init().
  kernel: remove HIPQUAD()
  netpoll: store local and remote ip in net-endian
  netfilter: fix endian bug in conntrack printks
  dmascc: fix incomplete conversion to network_device_ops
  gso: Fix support for linear packets
  skbuff.h: fix missing kernel-doc
  ni5010: convert to net_device_ops
2009-03-30 18:46:43 -07:00
Alexey Dobriyan
99b7623380 proc 2/2: remove struct proc_dir_entry::owner
Setting ->owner as done currently (pde->owner = THIS_MODULE) is racy
as correctly noted at bug #12454. Someone can lookup entry with NULL
->owner, thus not pinning enything, and release it later resulting
in module refcount underflow.

We can keep ->owner and supply it at registration time like ->proc_fops
and ->data.

But this leaves ->owner as easy-manipulative field (just one C assignment)
and somebody will forget to unpin previous/pin current module when
switching ->owner. ->proc_fops is declared as "const" which should give
some thoughts.

->read_proc/->write_proc were just fixed to not require ->owner for
protection.

rmmod'ed directories will be empty and return "." and ".." -- no harm.
And directories with tricky enough readdir and lookup shouldn't be modular.
We definitely don't want such modular code.

Removing ->owner will also make PDE smaller.

So, let's nuke it.

Kudos to Jeff Layton for reminding about this, let's say, oversight.

http://bugzilla.kernel.org/show_bug.cgi?id=12454

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
2009-03-31 01:14:44 +04:00
Nick Andrew
877d03105d trivial: Fix misspelling of firmware
Fix misspelling of firmware.

Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-03-30 15:21:59 +02:00
Alexander Beregalov
321dee6e8b wireless: remove duplicated .ndo_set_mac_address
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-29 13:52:21 -07:00
Ingo Molnar
82268da1b1 Merge branch 'linus' into percpu-cpumask-x86-for-linus-2
Conflicts:
	arch/sparc/kernel/time_64.c
	drivers/gpu/drm/drm_proc.c

Manual merge to resolve build warning due to phys_addr_t type change
on x86:

	drivers/gpu/drm/drm_info.c

Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-03-28 04:26:01 +01:00
Johannes Berg
e4e72fb4de mac80211/iwlwifi: move virtual A-MDPU queue bookkeeping to iwlwifi
This patch removes all the virtual A-MPDU-queue bookkeeping from
mac80211. Curiously, iwlwifi already does its own bookkeeping, so
it doesn't require much changes except where it needs to handle
starting and stopping the queues in mac80211.

To handle the queue stop/wake properly, we rewrite the software
queue number for aggregation frames and internally to iwlwifi keep
track of the queues that map into the same AC queue, and only talk
to mac80211 about the AC queue. The implementation requires calling
two new functions, iwl_stop_queue and iwl_wake_queue instead of the
mac80211 counterparts.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Reinette Chattre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:23 -04:00
Johannes Berg
b1720231ca mac80211: unify and fix TX aggregation start
When TX aggregation becomes operational, we do a number of steps:
 1) print a debug message
 2) wake the virtual queue
 3) notify the driver

Unfortunately, 1) and 3) are only done if the driver is first to
reply to the aggregation request, it is, however, possible that the
remote station replies before the driver! Thus, unify the code for
this and call the new function ieee80211_agg_tx_operational in both
places where TX aggregation can become operational.

Additionally, rename the driver notification from
IEEE80211_AMPDU_TX_RESUME to IEEE80211_AMPDU_TX_OPERATIONAL.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:22 -04:00
Wey-Yi Guy
08df05aa9b iwlwifi: show current driver status in user readable format
change the display of current driver status bit to user readable format
for better and easier debugging

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:20 -04:00
Bob Copeland
5a0fe8ac70 ath5k: properly drop packets from ops->tx
We shouldn't return NETDEV_TX_BUSY from the TX callback, especially
after we've mucked with the sk_buffs.  Drop the packets and return
NETDEV_TX_OK.

Changes-licensed-under: 3-Clause-BSD

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:19 -04:00
Christian Lamparter
de00c04ecb ar9170: single module build
This patch restores all-in-one module build procedure for ar9170.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:19 -04:00
Luis R. Rodriguez
051b919188 ath9k: fix dma mapping leak of rx buffer upon rmmod
We were claiming DMA buffers on the RX tasklet but never
upon a simple module removal.

Cc: stable@kernel.org
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:19 -04:00
Ivo van Doorn
14344b81ec rt2x00: New USB ID for rt73usb
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:18 -04:00
Bob Copeland
b726604706 ath5k: warn and correct rate for unknown hw rate indexes
ath5k sets up a mapping table from the hardware rate index to
the rate index used by mac80211; however, we have seen some
received frames with incorrect rate indexes.  Such frames
normally get dropped with a warning in __ieee80211_rx(),
but it doesn't include enough information to track down the
error.

This patch adds a warning to hw_to_driver_rix for any lookups
that result in a rate index of -1, then returns a valid rate so
the frame can be processed.

Changes-licensed-under: 3-Clause-BSD

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:18 -04:00
Lorenzo Nava
a3c0b87c4f b43: fix b43_plcp_get_bitrate_idx_ofdm return type
This patch fixes the return type of b43_plcp_get_bitrate_idx_ofdm. If
the plcp contains an error, the function return value is 255 instead
of -1, and the packet was not dropped. This causes a warning in
__ieee80211_rx function because rate idx is out of range.

Cc: stable@kernel.org
Signed-off-by: Lorenzo Nava <navalorenx@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:18 -04:00
Christian Lamparter
a1bfa0eb98 p54: Kconfig maintenance
This patch updates p54's Kconfig entry and removes the out-dated device list.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:18 -04:00
Christian Lamparter
4a48e2a484 ar9170: simplify & deBUG tx_status queueing and reporting
This patch simplifies the tx_status report code by using four tx_queues per
station instead of only one. (the skb lookup should be in O(1) now :-p ).

Also, it fixes a really obvious copy&paste bug in the janitor work code and
adds back a few spilled bits to the hardware definition header about QoS.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:14 -04:00
Tulio Magno Quites Machado Filho
af83debf5b ath5k: Support LED's on Acer Extensa 5620z
Add vendor ID for Quanta Microsystems and update the led table with the reported device.

Reported-by: Scott Barnes <nekoreeve@gmail.com>

Signed-off-by: Tulio Magno Quites Machado Filho <tuliom@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:10 -04:00
Christian Lamparter
75ca88c970 ar9170: update Makefile, Kconfig and MAINTAINERS
This patch update all necessary Makefile and Kconfig files.

Now you can then enable ar9170 in the kernel configuration under:
Device Drivers --->
	[*] Network device support --->
		Wireless LAN --->
			[*] Wireless LAN (IEEE 802.11)
			<M>   Atheros AR9170 support
			<M>     Atheros AR9170 USB support

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:09 -04:00
Christian Lamparter
b63a2cb304 ar9170: ar9170: USB frontend driver
USB frontend driver code for Atheros' AR9170 modules.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:09 -04:00
Christian Lamparter
6cb1935353 ar9170: mac/bbp and phy code
MAC/BBP and PHY programming code

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:09 -04:00
Christian Lamparter
e9348cdd28 ar9170: ar9170: mac80211 interaction code
This patch contains almost all mac80211 interaction code of AR9170.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:08 -04:00
Christian Lamparter
23b53f4f55 ar9170: hardware and eeprom header files
hardware / firmware interface definitions for Atheros' AR9170 based devices.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:08 -04:00
Luis R. Rodriguez
98dfaa5778 mac80211_hwsim: let the reg workqueue breathe when regtest is set
Without this the regulatory domain isn't seen and we end up
intersecting for each request (each radio).

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:06 -04:00
Pat Erley
9cb5412b07 Add mesh point functionality to ath9k
This patch enables mesh point operation for ath9k.  Tested with b43,
ath9k, rt2500usb, and ath5k as peers.

Signed-off-by: Pat Erley <pat-lkml@erley.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:06 -04:00
Christian Lamparter
d8cd7effc2 p54: fix SoftLED compile dependencies
This patch fixes a compile problem when the MAC80211_LEDS
triggers are enabled but not LED class itself.
(which is sort of pointless, but anyway...)

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:06 -04:00
Vasanthakumar Thiagarajan
6b2c40326f ath9k: Nuke struct ath_xmit_status
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:03 -04:00
Vasanthakumar Thiagarajan
8a92e2ee02 ath9k: Fix bug in reporting status of tx rate
This patch updates count of every hw tried rate with
appropriate tries before reporting tx status of a frame.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:03 -04:00
Michael Buesch
3e3ccb3d9b b43: Mask PHY TX error interrupt, if not debugging
This masks the PHY TX error interrupt, if debugging is disabled.

Currently we have a bug somewhere which triggers this interrupt once
in a while. (Depends on the network noise/quality). While this is nonfatal,
it scares the hell out of users and we frequently receive bugreports
that incorrectly identify this error message as the reason.

There's another problem with this. The PHY TX error interrupt is protected
with a watchdog that will restart the device if it keeps triggering very often.
This is used to fix interrupt storms from completely broken devices.

However, this watchdog might trigger in completely normal operation.
If the TX capacity of the card is saturated, the likeliness of the watchdog
triggering increases, as more TX errors occur. The current threshold
for the watchdog is 1000 errors in 15 seconds.

This patch adds a workaround for the issue by just enabling the interrupt
if debugging is disabled (by Kconfig or by modparam).

This has the downside that real fatal PHY TX errors are not caught anymore.
But this is nonfatal due to the following reasons:
* If the card is not able to transmit anymore, MLME will notice anyway.
* I did _never_ see a real fatal PHY TX error in a mainline b43 driver.
* It does _not_ result in interrupt storms or something like that.
  It will simply result in a stalled card. It can be debugged by enabling
  the debugging module parameter.

Signed-off-by: Michael Buesch <mb@bu3sch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:03 -04:00
Geert Uytterhoeven
1bf68e5cda wireless/p54: P54_SPI should depend on GENERIC_HARDIRQS
m68k allmodconfig:
| drivers/net/wireless/p54/p54spi.c: In function 'p54spi_probe':
| drivers/net/wireless/p54/p54spi.c:675: error: implicit declaration of function
| 'set_irq_type'
| make[4]: *** [drivers/net/wireless/p54/p54spi.o] Error 1

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:02 -04:00
Vasanthakumar Thiagarajan
0934af2340 ath9k: Fix rate control update for aggregated frames
We will miss rate control update if first A-MPDU of an
aggregation is not Block Acked as we always tell if the
rate control needs to updated through update_rc of first
A-MPDU. This patch does rate control update for the first
A-MPDU which notifies it's tx status (which is not
necessarily the first A-MPDU of an aggregation) to mac80211.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:01 -04:00
Abhijeet Kolekar
43da919232 iwl3945: replace stations with stations_39
A *leftover* stations is replaced with stations_39.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:00 -04:00
Wey-Yi Guy
a2f1cbebdc iwlwifi: report error when detect failure during stop agg queue
This fix related to bug 1921 at
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1921

when detect error during stopping tx aggregation queue, report the error to
help identify the problem.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:00 -04:00
Abhijeet Kolekar
82127493a6 iwl3945: control rate decrease
Control the rate decrease. Do not decrease the rate fast.
Use success_ratio for rate scaling :)

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:59 -04:00
Abhijeet Kolekar
1e680233e7 iwl3945: fix checkpatch.pl errors
Patch fixes two checkpatch.pl errors.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:59 -04:00
Abhijeet Kolekar
3e5d238fa7 iwl3945: use iwl_cmd_queue_free
iwl_cmd_queue_free needs to be used to free up the cmd_queue,
as TFD slots for cmd_queue and tx_queue are different.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:59 -04:00
Abhijeet Kolekar
21c02a1ab2 iwl3945: set TFD_QUEUE_MAX to correct value
Total number of queues is 8 but only 7 of them are TX queues.
4 AC(Data) queue ,1 CMD and 2 HCCA. The HCCA queues are not used.
max_txq_num is set to maximum usable TX queues.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:58 -04:00
Mohamed Abbas
b1c6019bc0 iwlwifi: support 11h
Set IEEE80211_HW_SPECTRUM_MGMT bit in hw->flags, this tell mac80211
we support spectrum mgmt.

Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:58 -04:00
Mohamed Abbas
28c608750f iwlcore: dont commit power command if interface is not up
If user set new power level, accept the new power level and only
send command to host if the interface is up and radio on.

Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:58 -04:00
Mohamed Abbas
4f01ac0153 iwlagn: allow power level setting all the times
allow user to set power level at all times

Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:57 -04:00
Wey-Yi Guy
5c2207c642 iwlwifi: return 0 for AMPDU_TX/RX_STOP request if NIC is going down
When receive IEEE80211_AMPDU_RX_STOP or IEEE80211_AMPDU_TX_STOP request
in iwl_mac_ampdu_action() from mac80211; check STATUS_EXIT_PENDING bit,
if NIC is on the way out, then return 0 back to mac80211, this can
prevent mac80211 report HW error incorrectly.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:57 -04:00
Mohamed Abbas
37fec3846a iwl3945: use changed in iwl3945_mac_config
In function iwl3945_mac_config use changed flag to call only
the affected functions.

Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:57 -04:00
Mohamed Abbas
019fb97d47 iwlagn: use changed in mac_config
In function iwl_mac_config use changed flag to call only
the affected functions. This patch also allow user to cache
channel, txpower and power value when the interface is not
ready and apply the changes once the interface ready.

Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:57 -04:00
Nick Kossifidis
8f655dde24 ath5k: Add tx power calibration support
* Add tx power calibration support
* Add a few tx power limits
* Hardcode default power to 12.5dB
* Disable TPC for now

v2: Address Jiri's comments

Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:56 -04:00
Bob Copeland
e23a9014fd ath5k: remove dummy PCI "retry timeout" fix
Remove the PCI retry timeout code, for all the same reasons that
Luis Rodriguez removed it for ath9k.

Changes-licensed-under: 3-Clause-BSD

Cc: Luis Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:55 -04:00
Bob Copeland
9ca9fb8aa8 ath5k: disable MIB interrupts
The MIB interrupt fires whenever counters overflow; however without
support for automatic noise immunity, we can sometimes get an interrupt
storm.  The get_stats() callback reads the counters anyway so we can
disable the interrupt for now until ANI is implemented.  This fixes
the issue reported in http://bugzilla.kernel.org/show_bug.cgi?id=12647.

Changes-licensed-under: 3-Clause-BSD

Cc: stable@kernel.org
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:54 -04:00
Nick Kossifidis
8e218fb24f ath5k: Convert chip specific calibration data to a generic format
* Convert chip specific calibration data to a generic format common
for all chips

Note: We scale up power to be in 0.25dB units for all chips for
compatibility with RF5112

v2: Address Bob's and Jiri's comments

Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:54 -04:00
Nick Kossifidis
504f365554 ath5k: Choose the right initvals for RF2425
* Fix a typo in initvals.c so that we use the RF2425 array for RF2425 and not RF2413

Note: This also fixes incorect pd gain overlap since RF2425 has different pd gain overlap from RF2413

Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:54 -04:00
Vasanthakumar Thiagarajan
85067c06ba ath9k: Keep LED on in idle state after association
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:53 -04:00
Johannes Berg
aae89831df wireless: radiotap updates
Radiotap was updated to include a "bad PLCP" flag and standardise
the "bad FCS" flag in the "flags" rather than "RX flags" field,
this patch updates Linux to that standard.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:52 -04:00
Sujith
cee075a24e ath9k: Update copyright in all the files
How time flies.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:51 -04:00
Sujith
c2da50e583 ath9k: Fix bug in handling single stream stations
AP mode currently sets up the dual stream capability
for all stations. This patch fixes it by checking if the
associated station supports dual stream MCS rates (8-15).
We would disregard any MCS rates above 15, since Atheros
HW supports only 0..15 rates currently, and can't receive
at rates > 15 anyway.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:51 -04:00
Sujith
95e4acb733 ath9k: Fill in ack signal in TX status
This patch fills the ack_signal field in TX status with an appropriate
value from the TX descriptor.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:51 -04:00
Sujith
e71cef37f1 ath9k: Fix bug in 4K EEPROM size calculation
We should be checking with the 4K header and not the non-4K
header size.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:50 -04:00
Sujith
d6509151bd ath9k: Change return type for set_board_values()
We always return true, checking for 'false' return value
is bogus anyway, so fix this.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:50 -04:00
Sujith
a83615d74d ath9k: Introduce a helper function for setting board gain values
This improves readability. Handle both 4K/non-4K EEPROM
in this patch.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:49 -04:00
Sujith
355363fcf7 ath9k: Move AR5416_VER_MASK to a common location
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:49 -04:00
Sujith
7d01b221b3 ath9k: Miscellaneous EEPROM handling cleanup
Print the EEPROM version/revision on init.
Choose appropriate debug masks on error conditions,
and remove useless print messages.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:47 -04:00
Luis R. Rodriguez
b572b24c57 ath9k: remove dummy PCI "retry timeout" fix
Remove the PCI retry timeout code as that was just taken from ipw2100
due to historical reasons but in reality its a no-op, additionally its
simply incorrect as each PCI devices has its own custom PCI configuration
space on PCI config space >= 0x40. Not to mention we were trying to write
0 to a place that already has 0 on it.

Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Ben Cahill <ben.m.cahill@intel.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Tested-by: Adel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:46 -04:00
Jouni Malinen
4ed96f04f8 ath9k: Add support for multiple virtual AP interfaces
This patch fixes the TSF offset calculation for staggered Beacon frames
and sets ATH_BCBUF back to the earlier value 4 to enable multi-BSS
configurations of up to four BSSes.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:46 -04:00
Vasanthakumar Thiagarajan
14587ce2a8 ath9k: Set IEEE80211_TX_CTL_RATE_CTRL_PROBE in rate control for probe rate
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:12:42 -04:00
Ingo Molnar
6e15cf0486 Merge branch 'core/percpu' into percpu-cpumask-x86-for-linus-2
Conflicts:
	arch/parisc/kernel/irq.c
	arch/x86/include/asm/fixmap_64.h
	arch/x86/include/asm/setup.h
	kernel/irq/handle.c

Semantic merge:
        arch/x86/include/asm/fixmap.h

Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-03-27 17:28:43 +01:00
Stephen Hemminger
0687478a99 wireless: convert wavelan to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-27 00:46:46 -07:00
Stephen Hemminger
8fdcf1aba3 wireless: convert arlan to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-27 00:46:45 -07:00
David S. Miller
23d12e2bdd rndis_wlan: Fix build with netdev_ops compat disabled.
Instead of storing a private ->set_multicast_list, just
have a private netdev ops.

Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-25 00:03:16 -07:00
Stephen Hemminger
5ae4efbcd2 hostap: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 22:55:36 -07:00
Stephen Hemminger
4cfa8e45f4 hostap: convert to internal net_device_stats
Use pre-existing net_device_stats in network_device struct.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 22:55:34 -07:00
Stephen Hemminger
44e9ad0b5a ipw2200: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 22:55:32 -07:00
Stephen Hemminger
3e47fcea20 ipw2100: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 22:55:32 -07:00
Stephen Hemminger
d5b3b9ae06 ipw2x00: convert infrastructure for use by net_device_ops
Expose routines so drivers can hook. Only set ptrs in netdev
if using old compat code.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 22:55:31 -07:00
Stephen Hemminger
ce55cbaf3a ipw2x00: convert to internal net_device_stats
Replace struct in ieee with current net_device_stats, so no longer
need get_stats hook

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 22:55:31 -07:00
Stephen Hemminger
f02abf1010 libertas: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 22:51:25 -07:00
Stephen Hemminger
bbfc6b788f libertas: convert to internal net_device_stats
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 22:51:24 -07:00
Stephen Hemminger
6456fffb09 prism54: convert to internal net_device_stats
Also, make ethtool_ops const as it should be, and get rid
of useless cast.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 22:51:23 -07:00
Stephen Hemminger
6685254f80 prism54: convert to net_device_ops
Also, make ethtool_ops const as it should be, and get rid
of useless cast.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 22:51:23 -07:00
Stephen Hemminger
98d2faaeb7 mac80211_hwsim: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 22:51:21 -07:00
Stephen Hemminger
2bd9f54d46 zd1201: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 22:51:21 -07:00
Stephen Hemminger
22bc1ce4f1 zd1201: convert to internal net_device_stats
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 22:51:20 -07:00
Stephen Hemminger
85a151b760 wl3501: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 22:51:20 -07:00
Stephen Hemminger
4255d41145 wl3501: convert to internal net_device_stats
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 22:51:19 -07:00
Stephen Hemminger
32f5a33009 raylan: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 22:51:19 -07:00
Stephen Hemminger
824f1dfdbe atmel: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 22:44:01 -07:00
Stephen Hemminger
7ae41cc3c0 airo: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 22:43:59 -07:00
Stephen Hemminger
9db0ba0a8b wavelan: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 22:43:59 -07:00
Stephen Hemminger
385e63fb1e wavelan: convert to internal net_device_stats
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 22:43:58 -07:00
Stephen Hemminger
1cc5920f0f strip: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 22:43:57 -07:00
Stephen Hemminger
1964e0dedf netwave: convert to net_device_ops
Also get rid of unneeded cast

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 22:43:57 -07:00
Stephen Hemminger
f56ef16eb0 netwave: convert to internal net_device_stats
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 22:43:56 -07:00
David S. Miller
af4330631c Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 2009-03-17 15:04:31 -07:00
David S. Miller
2d6a5e9500 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/igb/igb_main.c
	drivers/net/qlge/qlge_main.c
	drivers/net/wireless/ath9k/ath9k.h
	drivers/net/wireless/ath9k/core.h
	drivers/net/wireless/ath9k/hw.c
2009-03-17 15:01:30 -07:00
Reinette Chatre
808ff697b3 iwlwifi: correct log level when error occurs
user needs to see this message even if debugging disabled

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:47 -04:00
Reinette Chatre
18d426c4a8 iwlwifi: print contents of control register when error occurs
hopefully the register contents will guide us to why this failure occured

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:47 -04:00
Mohamed Abbas
48676eb3c3 iwlagn: fix warning when set WEP key
iwl_clear_station_table will be called every time rxon called.
In this function ucode_key_table is set to 0 even though a static
WEP security is set. This will cause in many warning and might be
an issue if dynamic WEP is set. This patch make sure we keep track
of all existing static WEP when this function is called.

Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:47 -04:00
Reinette Chatre
fd9377ee6c iwl3945: unmap previously mapped memory
During preparation of TX we create DMA mapping to TX command as part of
preparing the TFD. This mapping needs to be cleared at the time TFD is
freed.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:46 -04:00
Abhijeet Kolekar
732587ab43 iwl3945: use iwl_tx_cmd_complete
iwl3945 uses iwl_tx_cmd_complete to reclaim the unused buffers of the queue.
iwl_tx_cmd_complete in turn call the iwl_hcmd_queue_reclaim which will
unmap the dma mapping to tx_cmd and frees the memory.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:46 -04:00
Abhijeet Kolekar
dd5b687eda iwl3945 : fix rate scaling
Patch fixes the bug 1900 at
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1900

Issues:
Throughput and success ratio calculations were not done properly.
Number of retries were exceeding 16.

Fix:
Patch fixes above issues by doing window calculations inline with iwlwifi
Patch adds sanity check to limit number of retries to 16.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:46 -04:00
Abhijeet Kolekar
5c8df2d56a iwl3945: use iwl_led structure
3945 can now use iwl_led's structure from iwlwifi.
Patch also removes CONFIG_IWL3945_LEDS flag from Kconfig as 3945's led
support will now be enabled if user selects CONFIG_IWLWIFI_LEDS.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:46 -04:00
Abhijeet Kolekar
fa11d525ef iwl3945: fix sparse error
error is:
iwl3945-base.c:545:5: warning: symbol 'iwl3945_set_dynamic_key' was not
declared. Should it be static?

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:45 -04:00
Wey-Yi Guy
3c4955f8d9 iwlwifi: verify the antenna selection when receive fixed rate debugfs
When iwlwifi driver receive fixed rate debugfs command, validate the
antenna selection, if the selection is invalid, report the valid antenna
choice and do not set the rate scale table to fixed rate. Otherwise, set
the entire rate scale table to the fixed rate request by the user. this
validation can prevent sysassert happen in uCode

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:45 -04:00
Wey-Yi Guy
df36c044f5 iwlwifi: check IEEE80211_TX_STAT_AMPDU for agg pkt
when perform rate scaling, in tx status function, checking for
IEEE80211_TX_STAT_AMPDU flag instead of IEEE_TX_CTL_AMPDU flag to perform
AMPDU rate scaling operation.

IEEE80211_TX_CTL_AMPDU was set by mac80211 for aggregation pkt. But when
iwlwifi receive the tx status reply, it reset the flag to following
	info->flags = IEEE80211_TX_STAT_ACK;
	info->flags |= IEEE80211_TX_STAT_AMPDU;
it causes the rate-scaling to not work for aggregation pkt if we checking
for IEEE80211_TX_CTL_AMPDU flag.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:44 -04:00
Wey-Yi Guy
8fe723117a iwlwifi: HT performance improvement changes
During rate scaling, checking for 0 retry count before decrement
the count by 1, this can avoid the retry count to become 255 (0xff),
which will cause the rate to drop faster than what we expect during good
condition (receive 0 retry packet). also change the algorithm to make
the rate not drop faster than what we like.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:44 -04:00
Wey-Yi Guy
86b4766b05 iwlwifi: remove un-necessary rs_tl_turn_on_agg() after agg enabled
After the MLME handshaking complete and tx aggregation started for the
tid. Do not send unnecessary turn on aggregation request to mac80211.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:44 -04:00
Wey-Yi Guy
adb7b5e62b iwlwifi: add rf information in rate_scale debugfs command
Adding more Radio information when displaying
rate_scale_table. This can help to understand how many antenna and the
current RF condition such as SISO, MIMO2, MIMO3.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:43 -04:00
Wey-Yi Guy
d8ae4f52d8 iwlwifi: add valid tx antenna information in rate_scale_table debugfs
when display rate_scale_table debugfs information, also display valid tx
antenna information, this will help user to select correct antenna when
issue fixed rate debugfs command

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:43 -04:00
John Daiker
141fa61f10 ray_cs: checkpatch.pl and Lindent cleanups
Before: 1099 errors, 93 warnings, 2854 lines checked
After:  19 errors, 47 warnings, 2976 lines checked

The big bulk of this is code indent and over 80 character lines
(Lindent did this part) Other changes are foo * bar spacing, and
trailing whitespace.

v2: Cleans up ill-indented comments.  Subsequently, this reduces the
number of warnings, too.  Thanks to Joe Perches for pointing this out!

v3: Ran the whole file through Lindent first... which does most of
the work for me. :) Again, thanks to Joe Perches for this.

This is my final answer!

Signed-off-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:43 -04:00
Lennert Buytenhek
a66098daac mwl8k: Marvell TOPDOG wireless driver
Add a driver for Marvell 88w8xxx TOPDOG PCI/PCIe wireless parts.
This initial version supports the 88w8687 802.11b/g PCIe part on
channels 1-11, and only STA mode is currently implemented.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:43 -04:00
Jouni Malinen
217ba9da8e ath9k: Fix FIF_PROMISC_IN_BSS processing in station mode
We must not disable ACK sending in this case since it would break
normal station operations. In addition, clarify the comment about AP
mode to make more sense.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:42 -04:00
Sujith
eeee1320b7 ath9k: Add spectrum management to HW capabilities
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:42 -04:00
Luis R. Rodriguez
15cc0f1ac6 ath9k: make few eeprom and calib items static
This fixes the sparse complaints:

drivers/net/wireless/ath9k/eeprom.c:1407:5: warning: symbol
'ath9k_hw_4k_get_spur_channel' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:1436:19: warning: symbol
'eep_4k_ops' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:2808:5: warning: symbol
'ath9k_hw_def_get_spur_channel' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:2837:19: warning: symbol
'eep_def_ops' was not declared. Should it be static?
  CC [M]  drivers/net/wireless/ath9k/eeprom.o
  CHECK   drivers/net/wireless/ath9k/mac.c
  CC [M]  drivers/net/wireless/ath9k/mac.o
  CHECK   drivers/net/wireless/ath9k/calib.c
drivers/net/wireless/ath9k/calib.c:883:6: warning: symbol 'ar9285_clc'
was not declared. Should it be static?

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:42 -04:00
Luis R. Rodriguez
c117fa0bf5 ath9k: downgrade xmit queue full message to xmit debug
This is not a fatal message, hitting it simply means we're
going to tell the upper layers to slow their horses down but
as we make more descriptors available we let the show continue
by waking up the queues in ath_wake_mac80211_queue().

We downgrade this as otherwise we fill up your kernel log with
messages which can be common under heavy traffic.

Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:41 -04:00
Luis R. Rodriguez
4a5af9c292 mac80211_hwsim: add regulatory testing options
This adds a module parameter for mac80211_hwsim regulatory testing.
This module parameter is designed specifically to help test the
different possible types of driver specific regulatory requests
and also helps to test world roaming, all without any hardware.

If you want to just simply test different alpha2s just use the userspace
regulatory request as this won't buy you anything new.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:41 -04:00
Luis R. Rodriguez
7db90f4a25 cfg80211: move enum reg_set_by to nl80211.h
We do this so we can later inform userspace who set the
regulatory domain and provide details of the request.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:40 -04:00
Luis R. Rodriguez
0fee54cab7 cfg80211: remove REGDOM_SET_BY_INIT
This is not used as we can always just assume the first
regulatory domain set will _always_ be a static regulatory
domain. REGDOM_SET_BY_CORE will be the first request from
cfg80211 for a regdomain and that then populates the first
regulatory request.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:39 -04:00
John Daiker
8830cb678b atmel: checkpatch.pl cleanups
Before: 881 errors, 265 warnings, 4507 lines checked
After:  114 errors, 273 warnings, 4548 lines checked

This was mostly "space required after that ',' (ctx:VxV)".
Also a fair number of whitespace, code indent, and C99 comment cleanups.

New warnings introduced are all "line over 80 character"

md5sums are identical, as I skipped any fixes which may have altered the resulting binary.

Signed-off-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:38 -04:00
Sujith
62b4fb66c5 ath9k: Fix bug in reading debugfs file 'rcstat'
The rate table would not have been chosen before the interface
has been brought up. Reading 'rcstat' in this case would result
in an oops, fix this.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:38 -04:00
Sujith
c37452b068 ath9k: Fix bug in TX aggregation
mac80211 expects the driver to fill in the starting
sequence number of an ADDBA request to initiate TX aggregation.
IEEE80211_TX_CTL_AMPDU would be set for frames only after a
successful ADDBA exchange, but we have to increment the
internal sequence counter for the normal(non-AMPDU) data frames proerly.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:38 -04:00
Sujith
9c81e8be23 ath9k: Initialize ANI properly
ANI was not being initialized correctly for all HW variants.
This patch fixes it.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:38 -04:00
Bob Copeland
22e5b08585 ath5k: update LED table with reported devices
This patch adds support for Acer Ferrari 5000, and also specifies
the subsystem device ids for previously reported e-machines e510 and
Acer Aspire One A150.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:37 -04:00
Bob Copeland
cdb02dc614 ath5k: use a table for LED parameters
Put the device id-to-gpio mapping in a table to make it easier to add
new devices.  The list of supported devices is unchanged.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:37 -04:00
Bob Copeland
0ed4548f81 ath5k: extract LED code into a separate file
Move LED code out of base.c for clarity.

Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:37 -04:00
Jiri Slaby
8d6c39efed ath5k: don't change mac in eeprom_read_mac on error
Do not touch mac parameter passed to ath5k_eeprom_read_mac unless
we are sure we have correct address. I.e. when returning error, do
not change it.

While at it, use '= {}' compiler trick for memsetting mac_d.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:36 -04:00
Jiri Slaby
2c91108c55 ath5k: constify stuff
Make some structures const to place them in .rodata, since we won't
change them.

Most important parts of objdump -h:
-  0 .text         00011170
+  0 .text         00011140
-  5 .rodata       0000828e
+  5 .rodata       0000895e
- 13 .data         00000560
+ 13 .data         00000110
- 14 .devinit.data 00000260

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:36 -04:00
Jay Sternberg
77dcb6a952 iwlwifi: correct device name for 1000 series
device name was changed from 100 to 1000

Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:36 -04:00
Abhijeet Kolekar
8337031ef3 iwl3945: add test for new association
Add check for new association to ease reading.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:36 -04:00
Christian Lamparter
346de732cb p54: completely ignore rx'd frames with bad FCS
Passing frames with a bad FCS to the user is an optional feature.
However it doesn't work reliable and strangely not in the native monitor mode?!

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:35 -04:00
John Daiker
05c9a4cfe4 airo_cs: checkpatch.pl cleanups
Hopefully nothing controversial here, since the driver hasn't been touched in a while!

Before: 36 errors, 6 warnings, 482 lines checked
After:  0 errors, 3 warnings, 485 lines checked

This was nearly all trailing whitespace, * and parenthesis spacing, and code indent changes.

md5sum of object file before and after are identical.

Signed-off-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:35 -04:00
Vasanthakumar Thiagarajan
be1b08af61 ath9k: Use suitable macros with 4k eeprom data
This patch improves range and connection stability in AR9285.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:34 -04:00
Helmut Schaa
cc88aff073 ipw2x00: remove obsolete enums
Remove obsolete enums from ipw2x00/ieee80211.h, they are not used anymore.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:34 -04:00
Helmut Schaa
d74cc9a7a3 ipw2x00: Use IE definitions from linux/ieee80211.h
Use IE definitions from linux/ieee80211.h and drop the appropriate enum
from ipw2x00/ieee80211.h

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:34 -04:00
Helmut Schaa
30e1863ccb ipw2x00: remove duplicated defines
Remove several duplicated defines from ipw2x00/ieee80211.h which are
also available in linux/ieee80211.h.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:33 -04:00
Helmut Schaa
3756162b06 libipw: fix debug output
Replace all remaining occurrences of CONFIG_IEEE80211_DEBUG with
CONFIG_LIBIPW_DEBUG in libipw to allow debug output again.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:33 -04:00
Gabor Juhos
5077fd358b ath9k: always compile ath_radio_{en,dis}able
ath_radio_{en,dis}able is only compiled if RFKILL is enabled, but it is
required by the 'ath9k_wiphy_select' function.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:33 -04:00
Gabor Juhos
5210311543 ath9k: fix compile error in debug.c
drivers/net/wireless/ath9k/debug.c: In function 'read_file_wiphy':
drivers/net/wireless/ath9k/debug.c:377: error: implicit declaration of
function 'put_unaligned_le32'
drivers/net/wireless/ath9k/debug.c:378: error: implicit declaration of
function 'put_unaligned_le16'

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:32 -04:00
Gabor Juhos
9251f0b418 ath9k: fix compile error in ahb.c
drivers/net/wireless/ath9k/ahb.c: In function 'ath_ahb_probe':
drivers/net/wireless/ath9k/ahb.c:136: error: 'aphy' undeclared (first
use in this function)

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:32 -04:00
Gabor Juhos
6b765deb01 ath9k: fix AR_SREV_9100_OR_LATER macro
The current macro is wrong, because detects some AR5416 devices as an
AR9100 device. The AR5416 devices would have performance issues after
this change, because the contents of the ar5416 specific and of the
ar9100 specificinitval arrays are swapped. Fortunately we can correct
this with the rename of the arrays simply.

Changes-licesed-under: ISC

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:32 -04:00
Gabor Juhos
d4376ebe16 ath9k: move ar9100 version checking macros into a more appropriate place
All other version checking macros are in a common location within the
reg.h file. The AR_SREV_9100_OR_LATER macro is wrong currently, but will
be fixed with the next patch.

Changes-licensed-under: ISC

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:32 -04:00
Gabor Juhos
a8c96d3b22 ath9k: cleanup AR5416 version checking macros
Currently we have two different versions of this macros. Because they
would have to do the same thing, we should simplify and merge them.

Changes-licensed-under: ISC

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:31 -04:00
Senthil Balasubramanian
978b532642 ath9k: Incorrect AR9285 version check macro
Fix AR9285 1.1 and 1.2 version check macro.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:31 -04:00
Senthil Balasubramanian
4e84516838 ath9k: INI update for AR9285 and periodic PA offset caliberation
This patch updates the initvalues for AR9285 chipset and also adds
periodic PA offset caliberation.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:31 -04:00
Senthil Balasubramanian
b03a9db95a ath9k: RX buffers may be accessed/freed even before initialized/alloced.
accessing RXBUF list in ath_rx_cleanup may cause panic if
ath_descdma_setup fails even before RXBUF list is initialized.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:30 -04:00
Senthil Balasubramanian
f0e6ce13c1 ath9k: Get rid of unnecessary ATOMIC memory alloc during init time
We can sleep for memory during init time and so allocating rx buffers,
descriptro buffers with GFP_KERNEL should help us to get rid of transient
alloc fails.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:30 -04:00
Luis R. Rodriguez
22cad73587 mac80211_hwsim: add support for 5 GHz
ACME Inc. is now selling a dual band radio.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:29 -04:00
Christian Lamparter
94041b2940 p54: enable power save support
This patch enables power save support on all p54 devices.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:28 -04:00
Christian Lamparter
d0b45aef4f p54: initial SoftLED support
This patch adds SoftLED support for all p54 devices.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:28 -04:00
Christian Lamparter
efeada2c0a p54: fix iwconfig txpower off
Disabling the receiver logic with P54_FILTER_TYPE_RX_DISABLED is not
supported by all firmwares. However we have an alternative: hibernation.
And the only side effect - so far - is a bit less power consumption. WIN!

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:28 -04:00
Christian Lamparter
ad5e72ee81 p54pci: convert printk(KERN_* to dev_*
This patch replaces most printk(KERN_* "") with their by dev_* analogue.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:28 -04:00
Christian Lamparter
2ac710720c p54: unify ieee80211 device registration
All three drivers (p54pci, p54usb and p54spi) are implementing the
same functionality three times. So, why not put it into the shared library?!

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:27 -04:00
Christian Lamparter
fbf95296c1 p54usb: stop USB core interference in exit path
The patch fixes a problem when the (Soft)LED stayed on after the module was unloaded.
It turned out that the USB core disables all endpoints before calling the disconnect method.
So it was impossible to switch off the radio & LEDs.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:27 -04:00
Gabor Juhos
19d8bc22bc ath9k: create a common debugfs_root for all device instances
The driver are trying to create an 'ath9k' directory in debugfs for each
device currently. If there are more than one device in the system, the
second try will always fail.

Changes-licensed-under: ISC

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16 18:09:27 -04:00