The spin_lock handling uses lots of instructions on some archs.
With this patch the size of the ath9k module will be significantly
smaller.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we aren't doing anything in mac80211, we can turn off
much of the hardware, depending on the driver/hw. Not doing
anything, aka being idle, means:
* no monitor interfaces
* no AP/mesh/wds interfaces
* any station interfaces are in DISABLED state
* any IBSS interfaces aren't trying to be in a network
* we aren't trying to scan
By creating a new function that verifies these conditions and calling
it at strategic points where the states of those conditions change,
we can easily make mac80211 tell the driver when we are idle to save
power.
Additionally, this fixes a small quirk where a recalculated powersave
state is passed to the driver even if the hardware is about to stopped
completely.
This patch intentionally doesn't touch radio_enabled because that is
currently implemented to be a soft rfkill which is inappropriate here
when we need to be able to wake up with low latency.
One thing I'm not entirely sure about is this:
phy0: device no longer idle - in use
wlan0: direct probe to AP 00:11:24:91:07:4d try 1
wlan0 direct probe responded
wlan0: authenticate with AP 00:11:24:91:07:4d
wlan0: authenticated
> phy0: device now idle
> phy0: device no longer idle - in use
wlan0: associate with AP 00:11:24:91:07:4d
wlan0: RX AssocResp from 00:11:24:91:07:4d (capab=0x401 status=0 aid=1)
wlan0: associated
Is it appropriate to go into idle state for a short time when we have
just authenticated, but not associated yet? This happens only with the
userspace SME, because we cannot really know how long it will wait
before asking us to associate. Would going idle after a short timeout
be more appropriate? We may need to revisit this, depending on what
happens.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check for IEEE80211_TX_CTL_NO_ACK instead of is_multicast_ether_addr
when determining whether to use lowest rate without retries.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make iwl-{3945|agn}-rs check for IEEE80211_TX_CTL_NO_ACK instead of
is_multicast_ether_addr when determining whether to use the lowest
rate, and set the retry count to 0 (total try count = 1) if
IEEE80211_TX_CTL_NO_ACK is set.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Greear points out that the "too many interrupts" message will
never print in the intended case since the interrupt counter
will be -1 after the loop. Change it to pre-decrement so it will
be 0 on the thousandth iteration.
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend rt2x00lib capabilities to support 802.11n,
it still lacks aggregation support, but that can
be added in the future.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware require L2 padding between header and payload
because both must be aligned to a 4-byte boundary. This hardware
also is easier during the RX path since we no longer need to
move the entire payload but rather only the header to remove
the padding (mac80211 only wants the payload to be 4-byte aligned).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By placing the iv_len into the tx descriptor data and
by passing this data to the crypto IV handlers we can
save multiple calls to ieee80211_get_hdrlen_from_skb()
and some if-statements when copying/removing the IV data
from the outgoing frame.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 8e218fb24f reverted the previous
patch (commit 925be8a307).
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
remove redundant test: outlen is unsigned
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch takes care of an outstanding comment in
"[PATCH] ar9170usb: fix hang on resume" commit message.
>However, the device does not accept the firmware on resume.
>and it will exit with:
>
>> firmware part 1 upload failed (-71).
>> device is in a bad state. please reconnect it!
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch redo the driver code so that p54usb no longer hangs
the kernel on resume.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since "p54: prevent upload of wrong firmwares" we no longer allow
outdated LM86 firmwares to be uploaded on ISL3887 (LM87) devices.
Therefore we can purge this buggy legacy code altogether.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set null key type even on ar5211, otherwise it en/decrypts every frame with
protected bit set which renders the card unusable on encrypted networks.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch uncomment a few lines that survived the RFCs.
However, there is not much to worry about, since AP mode is
not officially advertised and supported.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otus uses slightly different set of "Minimum MPDU Start Spacing" values
than the 802.11n D2.0 specifies. (the whole table is shifted by one and
therefore the 16us spacing is not officially available!)
And while we're at it, we also initialize our MAC's density register.
So, this annoying _feature_ will not break TX A-MPDU later.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A typo slipped into my patch to configure beacon intervals
properly -- this warning is supposed to trigger when the
beacon interval is zero, not non-zero.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The config_interface method is a little strange, it contains the
BSSID and beacon updates, while bss_info_changed contains most
other BSS information for each interface. This patch removes
config_interface and rolls all the information it previously
passed to drivers into bss_info_changed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We currently have two beacon interval configuration knobs:
hw.conf.beacon_int and vif.bss_info.beacon_int. This is
rather confusing, even though the former is used when we
beacon ourselves and the latter when we are associated to
an AP.
This just deprecates the hw.conf.beacon_int setting in favour
of always using vif.bss_info.beacon_int. Since it touches all
the beaconing IBSS code anyway, we can also add support for
the cfg80211 IBSS beacon interval configuration easily.
NOTE: The hw.conf.beacon_int setting is retained for now due
to drivers still using it -- I couldn't untangle all
drivers, some are updated in this patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (30 commits)
e1000: fix virtualization bug
bonding: fix alb mode locking regression
Bluetooth: Fix issue with sysfs handling for connections
usbnet: CDC EEM support (v5)
tcp: Fix tcp_prequeue() to get correct rto_min value
ehea: fix invalid pointer access
ne2k-pci: Do not register device until initialized.
Subject: [PATCH] br2684: restore net_dev initialization
net: Only store high 16 bits of kernel generated filter priorities
virtio_net: Fix function name typo
virtio_net: Cleanup command queue scatterlist usage
bonding: correct the cleanup in bond_create()
virtio: add missing include to virtio_net.h
smsc95xx: add support for LAN9512 and LAN9514
smsc95xx: configure LED outputs
netconsole: take care of NETDEV_UNREGISTER event
xt_socket: checks for the state of nf_conntrack
bonding: bond_slave_info_query() fix
cxgb3: fixing gcc 4.4 compiler warning: suggest parentheses around operand of ‘!’
netfilter: use likely() in xt_info_rdlock_bh()
...
We need to be symmetrical in what is done when key is set and cleared.
This is important wrt the key flags as they are used during key
clearing and if they are not set when the key is set the key cannot be
cleared completely.
This addresses the many occurences of the WARN found in
iwl_set_tkip_dynamic_key_info() and tracked in
http://www.kerneloops.org/searchweek.php?search=iwl_set_dynamic_key
If calling iwl_set_tkip_dynamic_key_info()/iwl_remove_dynamic_key()
pair a few times in a row will cause that we run out of key space.
This is because the index stored in the key flags is used by
iwl_remove_dynamic_key() to decide if it should remove the key.
Unfortunately the key flags, and hence the key index is currently only
set at the time the key is written to the device (in
iwl_update_tkip_key()) and _not_ in iwl_set_tkip_dynamic_key_info().
Fix this by setting flags in iwl_set_tkip_dynamic_key_info().
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It does not make sense to apply EXPORT_SYMBOL to a static symbol. Fixes
this build error:
drivers/net/wireless/iwlwifi/iwl3945-base.c:1697: error: __ksymtab_iwl3945_rx_queue_reset causes a section type conflict
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
char bname[5] is too small for the string "X GHz" when the null
terminator is taken into account. Thus, turning on rate debugging
can crash unless we have lucky stack alignment.
Cc: stable@kernel.org
Reported-by: Paride Legovini <legovini@spiro.fisica.unipd.it>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Under certain circumstances iwlwifi can get stuck and will no
longer accept scan requests, because the core code (cfg80211)
thinks that it's still processing one. This fixes one of the
points where it can happen, but I've still seen it (although
only with my radio-off-when-idle patch).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rndis_wext_link_change() might be called from rndis_command() at
initialization stage and priv->workqueue/priv->work have not been
initialized yet. This causes invalid opcode at rndis_wext_bind on
some brands of bcm4320.
Fix by initializing workqueue/workers in rndis_wext_bind() before
rndis_command is used.
This bug has existed since 2.6.25, reported at:
http://bugzilla.kernel.org/show_bug.cgi?id=12794
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/iwlwifi/iwl3945-base.c:1415: error: __ksymtab_iwl3945_rx_queue_reset causes a section type conflict
I am pretty sure that this is a compiler bug, so not to worry. However,
as far as I can see, iwl-3945.o (the only user) and iwl3945-base.o are
always linked into the same module, so the EXPORT_SYMBOL (which causes
the problem) should not be needed. Correct?
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
net/mac80211/tx.c: In function ‘ieee80211_tx_h_select_key’:
net/mac80211/tx.c:448: warning: ‘key’ may be used uninitialized in this function
drivers/net/wireless/ath/ath9k/rc.c: In function ‘ath_rc_rate_getidx’:
drivers/net/wireless/ath/ath9k/rc.c:815: warning: ‘nextindex’ may be used uninitialized in this function
drivers/net/wireless/hostap/hostap_plx.c: In function ‘prism2_plx_probe’:
drivers/net/wireless/hostap/hostap_plx.c:438: warning: ‘cor_index’ may be used uninitialized in this function
drivers/net/wireless/hostap/hostap_plx.c:438: warning: ‘cor_offset’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/libertas/if_spi.c: In function ‘if_spi_c2h_data’:
drivers/net/wireless/libertas/if_spi.c:733: warning: format ‘%u’ expects type ‘unsigned int’, but argument 4 has type ‘long unsigned int’
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (94 commits)
netfilter: ctnetlink: fix gcc warning during compilation
net/netrom: Fix socket locking
netlabel: Always remove the correct address selector
ucc_geth.c: Fix upsmr setting in RMII mode
8139too: fix HW initial flow
af_iucv: Fix race when queuing incoming iucv messages
af_iucv: Test additional sk states in iucv_sock_shutdown
af_iucv: Reject incoming msgs if RECV_SHUTDOWN is set
af_iucv: fix oops in iucv_sock_recvmsg() for MSG_PEEK flag
af_iucv: consider state IUCV_CLOSING when closing a socket
iwlwifi: DMA fixes
iwlwifi: add debugging for TX path
mwl8: fix build warning.
mac80211: fix alignment calculation bug
mac80211: do not print WARN if config interface
iwl3945: use cancel_delayed_work_sync to cancel rfkill_poll
iwlwifi: fix EEPROM validation mask to include OTP only devices
atmel: fix netdev ops conversion
pcnet_cs: add cis(firmware) of the Allied Telesis LA-PCM
mlx4_en: Fix cleanup if workqueue create in mlx4_en_add() fails
...
Private structure is allocated by wiphy_new now, so use
wiphy_free instead of kfree.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rndis_wext_link_change() might be called from rndis_command() at
initialization stage and priv->workqueue/priv->work have not been
initialized yet. This causes invalid opcode at rndis_wext_bind on
some brands of bcm4320.
Fix by initializing workqueue/workers in rndis_wext_bind() before
rndis_command is used.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sparse complains, correctly, about these:
drivers/net/wireless/rndis_wlan.c:418:21: warning: symbol 'rndis_config_ops' was not declared. Should it be static?
drivers/net/wireless/rndis_wlan.c:423:6: warning: symbol 'rndis_wiphy_privid' was not declared. Should it be static?
Fix that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow user to config the device all the time but only allow commiting
these changes to card if the card is up and running.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch removes the "manual radio disable" parameter
as there is no usage scenario of disabling radio using this module parameter.
User can use iwconfig's txpower to enable and disable radio.
This module parameter also does not work as expected. During module load
the status of radio is set, the radio is not actually disabled. Even so,
the moment mac80211 requests the interface to be up the radio will be
enabled again.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Function rs_stay_in_table was flushing the rate scale table way to early. time_after
macro in expecting long value and was failing because we passing u32 value.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch clean up the code for NL80211_IFTYPE_MONITOR mode,
priv->iw_mode is set in add_interface, but add_interface is never called
for monitor mode.
The only way mac80211 informs us about monitor mode is through
configuring filter; since iw_mode will never set to
NL80211_IFTYPE_MONITOR, modify and remove all the code refer to
NL80211_IFTYPE_MONITOR and replace with iwl_is_monitor_mode() function
call.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch calculates interrupt statistics for debugfs.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch adds debugfs to 3945. Also fix debugfs registration in iwlagn
to return error code if it fails.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If passive scanning is requested we should not ask the
microcode to do active scanning after detecting traffic
on a channel -- that should only be used when an active
scan is requested but some channels are marked passive.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This modifies iwlwifi to
* no longer build its own probe request, but use mac80211's
* therefore, support arbitrary scan IEs (up to the max len)
* support multiple scan SSIDs
* support passive scanning
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This limit applies to current (APIv1 and APIv2) 3945 firmware only, not
supported firmware of any of the other cards.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this patch ar9170 is capable of receiving aggregated 802.11n frames
and sniffing on most networks without having a "debug message overhead".
(Includes phy initialization requested by
Johannes Berg <johannes@sipsolutions.net> -- JWL)
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for configuring HT40 channels
and receiving HT40 to ar9170. Receiving aggregation
doesn't seem to work right now, so it's not enabled.
Same goes for TX aggregation, but that probably needs
even more work.
With this, I can receive roughly 33 Mbits/sec.
The HT capabilities are a little odd, I tried following
otus here -- in particular having SGI_40 but not SGI_20
is a little weird but afaict that's what otus does.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Supporting wireless extension nickname is pointless
and no other modern driver supports this, so remove
it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trying to separate header files into net/wireless.h and
net/cfg80211.h has been a source of confusion. Remove
net/wireless.h (because there also is the linux/wireless.h)
and subsume everything into net/cfg80211.h -- except the
definitions for regulatory structures which get moved to
a new header net/regulatory.h.
The "new" net/cfg80211.h is now divided into sections.
There are no real changes in this patch but code shuffling
and some very minor documentation fixes.
I have also, to make things reflect reality, put in a
copyright line for Luis to net/regulatory.h since that
is probably exclusively written by him but was formerly
in a file that only had my copyright line.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PS-Polled frames must be sent with OUT_NOCANCEL flag set,
or the firmware will reject all of them, at the station is still blacklisted.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The following patch implements some control over the LED on RTL8187B and
RTL8187L devices. Triggers are registered for TX and RX. Whenever the
trigger event occurs, the LED is turned off for 1/20 second, then turned
back on.
Note: For those RTL8187X devices that are built into the computer and have
a LED that is expected to be controlled with a radio switch, this patch will
not operate that LED. That will take a separate patch to be prepared later.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A detection function was added for identifying CF8381.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch deactivates powersave in station mode.
It does not work correctly yet, so the code does more harm than good.
(I split the original patch and sent part of it for 2.6.30, which didn't
have the IEEE80211_HW_BEACON_FILTER flag. -- JWL)
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the EEPROM is not in good condition we cannot continue so
we currently bail out but only ath5k is bailing out properly.
Both ath9k and ar9170 were proceeding and if a user were to run
into this they'd see an obscure panic. Lets propagate the error
as intended and make sure we inform the user by lifting the
error message from debug to a kernel error.
Stable note: You can find a port of this page here:
http://bombadil.infradead.org/~mcgrof/patches/ath9k/ath9k-fix-eeprom.patch.txt
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Grabbing an ath5k_buf then dropping the lock is racy because the
referenced descriptor can be obtained in another thread and released
before the buffer is handed to the hardware. Likewise, manipulating
sc->rxlink without the lock can lead to having multiple self-linked
hardware descriptors.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch simplifies the code used to detect when the
self-linked DMA buffer is still in use by hardware, by
checking the hardware's rxdp register instead of looking
at the software buffer list.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current code uses int types, but both modparams are boolean values.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For embedded platforms, beacon transmission can be starved when
flooded with data packets. Prioritize beacons by giving the beacon
queue the first shot when the isr completes.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch corrects a few errors in the initvals tables to match those
in the HAL tables. Namely, remove a couple of repetitions, fix some
turbo mode errors, and correct a register for the CCK rate power table.
Changes-licensed-under: ISC
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christoph Hellwig pointed out that these stubs are unnecessary.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds licensing, author information and a description to the module.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This message appears to be nothing more than a leftover of the
experimental-8187B era. Also, we print the HW type in the hwaddr line,
making this message reduntant. And it's definitely not important
enough to be a KERN_WARNING.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is already handled properly in ath9k_hw_getnf.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in ath9k_hw_init_cal() where the wrong
calibration was being done for non-AR9285 chipsets.
Also add a few helpful comments.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces old 'hal_' prefixes with 'ath9k_'.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up the functions dealing with calibration,
using proper return values.
ath9k_hw_per_calibration(), ath9k_hw_calibrate now return bool values
instead of setting error values in the function arguments.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The various ANI timers have to be initialized properly when
starting the calibration timer.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ADC gain calibration has to be done for all non 2GHZ-HT20 channels.
Regression from "ath9k: use ieee80211_conf on ath9k_hw_iscal_supported()"
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The operating HT mode is stored in chanmode and
not channelFlags.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A full HW reset needs to be done on termination of a scan run.
Not setting SC_OP_FULL_RESET resulted in doing a
fast channel change.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver-specific region has to be freed in case
of a DMA mapping failure.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Radio enable/disable have to handle ASPM state properly.
This patch fixes it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_getisr() doesn't appear to set anything in the status mask for
PCI FATAL or PERR interrupts (AR_INTR_SYNC_HOST1_FATAL/PERR), which
the open-source HAL seems to do. This means that the card isn't reset
after these interrupts.
This patch seems to fix a problem where the wireless drops out with an
"ath9k: received PCI FATAL interrupt" in dmesg after some time; the
hardware is an AR5416 in an ASUS WL-500W running 2.6.28.7 (OpenWRT) and
compat-wireless 2009-03-31.
Signed-off-by: Steven Luo <steven@steven676.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ports commit c97a4ccc1f "b43: Fix beacon BH update" to
b43legacy. It fixes beacon updating in the bottomhalf. In case the device
is busy, we will defer to later in the IRQ handler.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Tested-by: David Ellingsworth <david@identd.dyndns.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ports the beaconing fixes from commit a82d992261 "b43: Beaconing
fixes" to b43legacy. Basically it prevents the card from triggering the beacon
IRQ over and over again.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Tested-by: David Ellingsworth <david@identd.dyndns.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The signal quality percentage is now calculated by mac80211 stack.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch takes care of outstanding TODOs:
/* TODO: some devices have 4 more free slots for rx keys */
Now the driver can utilize all available key slots instead of just 4.
Obviously, this helps most in AP/IBSS(/MESH) mode, when
we have to use more different keys.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes unnecessary MMIO accesses in the interrupt hotpath.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/libertas/rx.c: In function ‘lbs_process_rxed_packet’:
drivers/net/wireless/libertas/rx.c:184: warning: format ‘%zd’ expects type ‘signed size_t’, but argument 4 has type ‘__le32’
drivers/net/wireless/libertas/rx.c:184: warning: format ‘%zd’ expects type ‘signed size_t’, but argument 5 has type ‘unsigned int’
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds interrupt statistics report to debugfs, this can help to
understand number of interrupts happened which including HW/SW error for
easier and better debugging.
in /sys/kernel/debug/ieee80211/phyN/iwlagn/data directory
use "cat interrupt" to view the current interrupt counter
use "echo 0 > interrupt" to clear interrupt counter
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix displaying of wrong channel information when user query
channel through debugfs
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For completeness, we should also make sure that the 3x3 MIMO rates are also checked when seeing if one rxon struct matches another.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to sync rxon_active with changes after we commit rxon_assoc,
without rxon_active will still have the old data that cause
iwl_send_rxon_assoc to fail with no change in rxon command.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug introduced by commit "iwlwifi: adding MIMO3 support
in rate scaling". We should not set the dual_stream_ant_msk (for 2x2 MIMO)
when using a 3x3 rate, this will cause a SYSASSERT in uCode.
Note: there is no triple_stream_ant_msk, because all three antennas are used.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adding MCS information in rate_scale_table, it help for
debugging rate scaling algorithm, easy to understand what is the current
rate scale table and matching modulation, plus the last mcs used for tx.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can now use iwl_mac_reset_tsf from iwlwifi.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can now use iwl_mac_get_tx_stats from iwlwifi.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can now use iwl_mac_config_interface from iwlwifi.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add config_ap lib op to iwlwifi and iwl3945 in preparation
of future 3945 porting actions.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can now use iwl_mac_config from iwlwifi
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can now use iwl_mac_remove_interface from iwlwifi
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can now use iwl_set_mode from iwlcore library.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add set_rxon_chain op to iwlwifi cfg ops in preparation of
future 3945 porting work.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl3945 can now use iwl_get_sta_id.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch unifies the add_station function for 3945 and iwlwifi drivers.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch replaces station function used in driver by station management ops
in 3945.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds declarations for station management ops to iwlwifi drivers.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Delay mode setting till uCode is ready.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can use iwl_mac_beacon_update.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can use iwl_bss_info_changed.
A new lib op is created for post_assoicate to distinguish between
3945 and iwlwifi's post_associate operations.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
libertas: add support for Marvell SD8688 chip
Use RxPD->pkt_ptr to locate eth803 header in the packet
received since SD8688/v10 firmware allows a gap between
RxPD and eth803 header.
Set SDIO block size to 256 for CMD53.
The maximum block size for SD8688 WLAN function is set
to 512 in TPLFE_MAX_BLK_SIZE. But using 512 as block size
results upto 2K bytes data (4 blocks) being transferred
and causes buffer overflow in firmware.
Both changes above are backward compatible with earlier
firmware versions for SD8385/SD8686.
The SDIO_DEVICE_IDs for SD8688 chip are added in
include/linux/mmc/sdio_ids.h
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
p54spi_wakeup and p54spi_tx_frame used busy-waiting loop
to poll for 'ready' bits in SPI_ADRS_HOST_INTERRUPTS register.
With this change in place 'WR_READY timeout' messages do not
show anymore.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for the LEDs on the Jupiter netbook.
Reported-by: Martin Bammer <mrb74@gmx.at>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, the libertas main thread contends with the spi driver thread
in the TX path. To improve throughput, ensure that the driver thread
has higher scheduling priority than the libertas main thread. Do this
by making the libertas spi driver thread a low priority real time
thread.
We measured an average throughput improvement of 13%.
Signed-off-by: Anna Neal <anna@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adding few more debug messages if encounter error when driver
try to start tx aggregation queue. Also change from IWL_ERR to
IWL_DEBUG_HT is the HW legacy queue is empty when driver request to move
to aggregation queue.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Separated the MIMO tpt matrix into MIMO2 and MIMO3, adding MIMO3 support
in rate scaling algorithm. If the device support 3x3, then utilize all
three antenna (A/B/C) for tx to improve throughput.
Adding rs_switch_to_mimo3() function to allow switch to mimo3 modulation
mode from other modes(legacy/siso/mimo2). Adding rs_move_mimo3_to_other()
function to allow switch from mimo3 modulation mode to either siso or mimo2;
also support toggle between SGI and NGI.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding ht triple_stream_basic_rates for MIMO3 supports
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the EEPROM contains weird values for the power levels we have to
fix the interpolation process.
Signed-off-by: Fabio Rossi <rossi.f@inwind.it>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Auto-depend on HW_RANDOM, rather than "select"ing it.
This way the user has the choice to enable or disable HWRNG support.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces a new attribute for a wiphy that tells
userspace how long the information elements added to a probe
request frame can be at most. It also updates the at76 to
advertise that it cannot support that, and, for now until I
can fix that, iwlwifi too.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/ath5k/led.c:81:6: warning:
symbol 'ath5k_led_on' was not declared. Should it be static?
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make ath5k select the ath module and add in the hooks to make the
eeprom regulatory hint and reg notifier take effect.
Changes to attach.c
Changes-licensed-under: ISC
Changes to base.c
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setup the wiphy regulatory parameters when first initializing the
Atheros regulatory module. We can remove five exported symbols this
way and simplify the driver code for both ath5k and ath9k.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change creates a new module, ath.ko, which includes code that can
be shared between ath5k, ath9k and ar9170. For now, extract most of the ath9k
regulatory code so it can also be used in ath5k.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All regulatory information is encapsulated by the ath9k_regulatory
struct, so we can now change all the callers to take that directly
instead of struct ath_hw. This in turn will enable us to move the
regulatory functions to common code also used by ath5k, since both
can use this regulatory struct.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Until ath5k and ath9k share common channel structures, they will have
to implement their own get_ctl() function. Split out the portion that
only relies on the current band and reg domain so that it can be common
code.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The STATUS_ALIVE value cannot be used because it is cleared when
interface is brought down and will not be set if rfkill is enabled when
interface is started again. The interface can thus not be brought up if
rfkill was enabled before stopping the interface and disabled after
starting the interface.
Change the test to use priv->is_open instead, this will be set when
interface is started whether rfkill is enabled or not.
Thanks to Helmut Schaa for the suggested fix.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert scan function to cfg80211. Unlike old scan code new code
waits 1 sec before getting scan data from device and passing
forward to cfg80211.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change quality level scale to match cfg80211 CFG80211_SIGNAL_TYPE_UNSPEC.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[edit: made rndis_change_virtual_intf static]
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds beacon filtering support to p54.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch hopefully finishes the SoftLED code:
- It adds two more LEDs (rx and radio).
(the FW claims it can support up to 16 LEDs,
but I doubt that any vendor put more than 4 on a board)
- update the LEDs in a _delayed_ workqueue.
No one reported any more crashes.
(see: "PATCH] p54: fix race condition in memory management")
So we can stop burning the mm code.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch rearrange and regroups most elements in p54_common.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Claiming every available 5 ghz channel has a couple of negative
side-effects: scanning takes a long time, and the channel list
overflows the available buffer space for netlink commands,
resulting in:
$ iw phy phy0 info
command failed: No buffer space available (-105)
This patch adds a modparam so people who want to see all the channels
can do so by passing all_channels=1. By default users will see a
smaller list of channels. This also halves scan time, from 10 seconds
down to less than 5 when using world regulatory.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Reported-by: Simon Farnsworth <simon@farnz.org.uk>
Tested-By: Simon Farnsworth <simon@farnz.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in checking for HT40 mode.
The STA's mode can be determined from the cached HT capabilities,
use that and remove the redundant variable 'rc_phy_mode'.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The number of streams supported by a STA can be determined
directly from the HT capabilities. Remove the redundant
variable storing the stream cap.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up the ISR, removing a unnecessary do..while
loop, and waking up the chip before getting the pending
interrupts.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handle aggregation params only when aggregation is
supported.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These are unnecessary constructs in a function.
This patch removes these from both RX and TX init
routines.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We never handle TIM, TIM_TIMER is used instead.
Remove this and the unnecessary swBeaconProcess variable.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Creation of the root debugfs file could have failed
for some reason, check properly before proceeding in this
case.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
struct aggr_rifs_param and ath_tx_stat are not used anywhere.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using a u32 to store a single flag is overkill.
Use a bool to store whether the buffer is stale or not.
Also, use u8 instead of u32 to store the buffer type.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change the void pointer to struct sk_buff and access
bf_mpdu directly, removing all casts in the process.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The state is already stored in ath9k_ops_config, so remove
the duplicate variable in ath_hw.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This routine always return true, checking for false
in the return value is invalid. Fix this.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean debug messages to use appropriate levels,
remove useless messages, and trim the number of
debug levels.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We get the valid chainmasks on HW attach, checking
it again during reset is redundant. This patch removes the check.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes unused HW capability flags and
HW operation variables, and a chainmask flag that
we don't use anywhere.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For chipsets supporting autosleep feature, there is no need to abort
Rx engine since they are capable of automatically going back to sleep
after receiving a packet.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Auto-depend on HW_RANDOM, rather than "select"ing it.
This way the user has the choice to enable or disable HWRNG support.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00link_reset_qual() is not declared in a header,
and is only internally used within rt2x00link.c.
It should be declared as static.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pci_dev->irq and pci_name(pci_dev) access should be limited
to rt2x00pci only. This is more generic and allows a rt2x00 pci
driver to be controlled as PCI device but also as platform driver
(needed for rt2800pci SoC support).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a locking problem which freezes the network core.
The deadlock goes as follows:
- ar9170_op_stop - is called
1. change the state to IDLE
2. > take the MUTEX <
3. cancel_SYNC all pending work, which means
"block until a work_struct's callback has terminated"
=> if filter_config_work was queued it tries to get the MUTEX,
before checking the device state...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR5K_PHY_PLL_40MHZ_5413 should not be ORed with AR5K_PHY_MODE_RAD_RF5112
for 5 GHz channels.
The incorrect PLL value breaks scanning in the countries where 5 GHz
channels are allowed.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Almost all drivers do not support user_claim, so remove it
completely and always report -EOPNOTSUPP to userspace. Since
userspace cannot really drive rfkill _anyway_ (due to the
odd restrictions imposed by the documentation) having this
code is just pointless.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware may insert up to 4 padding bytes after the lmac header,
but it does not amend the size of SPI data transfer.
Such packets has correct data size in header, thus referencing
past the end of allocated skb. Put extra 4 bytes to the end of the
received skb to compensate for this case.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With mac80211's help to call stop() and start() in mac80211
suspend/resume function, both iwlagn and iwl3945 no longer calling
stop() and start(); remove un-necessary STATUS_IN_SUSPEND bit from both
header files and functions,
Move apm_ops.stop() function into pci_suspend() to ensure
DMA is stopped before go into suspend mode.
iwl3945 has the similar suspend/resume function as iwlagn, so move both
functions to iwlcore to be shared by both drivers.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
p54spi_tx_frame wasn't waiting for HOST_ALLOWED in SPI_ADRS_DMA_WRITE_CTRL.
This resulted in frequent 'WR_READY timeout' on beacon resubmission.
Also don't free skb on error path, as it gets freed on p54spi_wq_tx.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CMD_MESH_CONFIG command ID and a couple of structure members in TxPD,
RxPD have been changed in firmware version 10.x.y.z and newer.
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of firmware itself p54_upload_firmware was sending to the device
content of struct firmware and the following random garbage.
Notice '&' before priv->firmware->data at p54spi_spi_write.
But simple removing of '&' sign triggered BUG_ON at dma_cache_maint.
Thus kmemdup - kfree workaround.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mask value read from SPI_ADRS_DMA_WRITE_CTRL in p54spi_wait_bit.
Without this, 'fw_upload not allowed to DMA write' is observed at both N800 and N810.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few issues wrt DMA were uncovered when using the driver with swiotlb.
- driver should not use memory after it has been mapped
- iwl3945's RX queue management cannot use all of iwlagn because
the size of the RX buffer is different. Revert back to using
iwl3945 specific routines that map/unmap memory.
- no need to "dma_syn_single_range_for_cpu" followed by pci_unmap_single,
we can just call pci_unmap_single initially
- only map the memory area that will be used by device. this is especially
relevant to the mapping of iwl_cmd. we should not map the entire
structure because the meta data at the beginning of structure contains
the address to be used later for unmapping. If the address to be used for
unmapping is stored in mapped data it creates a problem.
- ensure that _if_ memory needs to be modified after it is mapped that we
call _sync_single_for_cpu first, and then release it back to device with
_sync_single_for_device
- we mapped the wrong length of data for host commands, with mapped length
differing with length provided to device, fix that.
Thanks to Jason Andryuk <jandryuk@gmail.com> for significant bisecting
help to find these issues.
This fixes http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1964
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Jason Andryuk <jandryuk@gmail.com>
Tested-by: Ben Gamari <bgamari@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When debugging TX issues it is helpful to know the seq nr of the
frame being transmitted. The seq nr is printed as part of ucode's
log informing us which frame is being processed. Having this information
printed in driver log makes it easy to match activities between driver
and firmware.
Also make possible to print TX flags directly. These are already printed
as part of entire TX command, but having it printed directly in cpu format
makes it easier to look at.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a build warning in mwl8.c.
(Marvell TOPDOG wireless driver)
The warning it fixes is: "large integer implicitly truncated to unsigned type."
The rx_ctrl member of the mwl8k_rx_desc struct is 8 bit (__u8 ), whereas trying
to assign it a 32 bit value (which is returned from cpu_to_le32())
causes the compiler to issue
a truncation warning.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Users reported lockup with work still trying to run
after module has been unloaded.
http://thread.gmane.org/gmane.linux.kernel.wireless.general/30594/focus=30601
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reported-by: TJ <ubuntu@tjworld.net>
Reported-by: Huaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the bug where some revisions of 6000 series hardware cannot
be used. Later versions of 6000 series have the EEPROM replaced by
OTP. For these devices to be used we need to expand valid EEPROM mask.
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sparse says:
drivers/net/wireless/atmel.c:1501:3: warning: Initializer entry defined twice
drivers/net/wireless/atmel.c:1505:3: also defined here
and it's correct; atmel has its own ndo_change_mtu and
shouldn't use eth_change_mtu.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a hang on resume when the filesystem is not
available and request_firmware blocks.
However, the device does not accept the firmware on resume.
and it will exit with:
> firmware part 1 upload failed (-71).
> device is in a bad state. please reconnect it!
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
swap mwl8k_remove and mwl8k_shutdown functions to allow
"rmmod mwl8k; modprobe mwl8k"
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch deactivates powersave in station mode.
It does not work correctly yet, so the code does more harm than good.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After suspend & resume the rt2x00 devices won't wakeup
anymore due to a broken register information setup.
The most important problem is the release of the EEPROM
buffer which is completely cleared and never read again
after the suspend.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
arm will pad even between u8's, so mark the structs/unions
packed. Fixes a build bug on arm due to BUILD_BUG_ON tests
in the code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the value read from HERMES_RID_TXQUEUEEMPTY becomes 0 after exactly
100 readings, we wrongly consider it a timeout. Rewrite the clever
while loop as a for loop that does the right thing and looks simpler.
Reported by Juha Leppanen <juha_motorsportcom@luukku.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I forgot that iwl3945 registration is separate from iwlagn.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The assertion of the lock-bit in the hardware register is unreliable,
because there are devices with quirks that will randomly set the bit.
Do the assertion in software, only.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a new device to ar9170usb.
Reported-by: Mike Kershaw/Dragorn <dragorn@kismetwireless.net>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Code was clearly wrong, plus callers expect the mode change to happen as
soon as possible, not dropped on the floor until the next time some
other config value changes and a commit happens.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add USB device ID for OQO 01+'s internal wireless LAN
An OQO employee mentions the chip's true identity here:-
ftp://ftp.oqo.com/unsupported/linux/OQOLinux.html
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't lead memory when receive errors
Signed-off-by: Philip Rakity <prakity@yahoo.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the following waring:
> ------------[ cut here ]------------
>WARNING: at kernel/softirq.c:138 local_bh_enable+0x54/0xbc()
>Modules linked in: p54spi
>[<c0034ff8>] (dump_stack+0x0/0x14)
>[<c005b1a4>] (warn_on_slowpath+0x0/0x68)
>[<c00604c8>] (local_bh_enable+0x0/0xbc)
>[<bf000000>] (p54spi_op_tx+0x0/0x4c [p54spi])
>[<c01a4d34>] (p54_sta_unlock+0x0/0x78)
p54spi_op_tx needs to be called from different locking contexts.
Therefore we have to protect the linked list with irqsave spinlocks.
Reported-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I'm very sorry, as this change belongs to the other patch:
"[PATCH] p54: fix SoftLED compile dependencies".
however I must have somehow lost "git add" for that file.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The RX buffer poison needs to be refreshed, if we recycle an RX buffer,
because it might be (partially) overwritten by some DMA operations.
Cc: stable@kernel.org
Cc: Francesco Gringoli <francesco.gringoli@ing.unibs.it>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds poisoning and sanity checking to the RX DMA buffers.
This is used for protection against buggy hardware/firmware that raises
RX interrupts without doing an actual DMA transfer.
This mechanism protects against rare "bad packets" (due to uninitialized skb data)
and rare kernel crashes due to uninitialized RX headers.
The poison is selected to not match on valid frames and to be cheap for checking.
The poison check mechanism _might_ trigger incorrectly, if we are voluntarily
receiving frames with bad PLCP headers. However, this is nonfatal, because the
chance of such a match is basically zero and in case it happens it just results
in dropping the packet.
Bad-PLCP RX defaults to off, and you should leave it off unless you want to listen
to the latest news broadcasted by your microwave oven.
This patch also moves the initialization of the RX-header "length" field in front of
the mapping of the DMA buffer. The CPU should not touch the buffer after we mapped it.
Cc: stable@kernel.org
Reported-by: Francesco Gringoli <francesco.gringoli@ing.unibs.it>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since both ipw2100 and ipw2200 are already converted to new
net_device_ops this code is useless.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove pointless conditional before kfree_skb().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the second go through of the old DMA_nBIT_MASK macro,and there're not
so many of them left,so I put them into one patch.I hope this is the last round.
After this the definition of the old DMA_nBIT_MASK macro could be removed.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Greg KH <greg@kroah.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_30BIT_MASK macro with DMA_BIT_MASK(30)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
wireless: remove duplicated .ndo_set_mac_address
netfilter: xtables: fix IPv6 dependency in the cluster match
tg3: Add GRO support.
niu: Add GRO support.
ucc_geth: Fix use-after-of_node_put() in ucc_geth_probe().
gianfar: Fix use-after-of_node_put() in gfar_of_init().
kernel: remove HIPQUAD()
netpoll: store local and remote ip in net-endian
netfilter: fix endian bug in conntrack printks
dmascc: fix incomplete conversion to network_device_ops
gso: Fix support for linear packets
skbuff.h: fix missing kernel-doc
ni5010: convert to net_device_ops
Setting ->owner as done currently (pde->owner = THIS_MODULE) is racy
as correctly noted at bug #12454. Someone can lookup entry with NULL
->owner, thus not pinning enything, and release it later resulting
in module refcount underflow.
We can keep ->owner and supply it at registration time like ->proc_fops
and ->data.
But this leaves ->owner as easy-manipulative field (just one C assignment)
and somebody will forget to unpin previous/pin current module when
switching ->owner. ->proc_fops is declared as "const" which should give
some thoughts.
->read_proc/->write_proc were just fixed to not require ->owner for
protection.
rmmod'ed directories will be empty and return "." and ".." -- no harm.
And directories with tricky enough readdir and lookup shouldn't be modular.
We definitely don't want such modular code.
Removing ->owner will also make PDE smaller.
So, let's nuke it.
Kudos to Jeff Layton for reminding about this, let's say, oversight.
http://bugzilla.kernel.org/show_bug.cgi?id=12454
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Conflicts:
arch/sparc/kernel/time_64.c
drivers/gpu/drm/drm_proc.c
Manual merge to resolve build warning due to phys_addr_t type change
on x86:
drivers/gpu/drm/drm_info.c
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch removes all the virtual A-MPDU-queue bookkeeping from
mac80211. Curiously, iwlwifi already does its own bookkeeping, so
it doesn't require much changes except where it needs to handle
starting and stopping the queues in mac80211.
To handle the queue stop/wake properly, we rewrite the software
queue number for aggregation frames and internally to iwlwifi keep
track of the queues that map into the same AC queue, and only talk
to mac80211 about the AC queue. The implementation requires calling
two new functions, iwl_stop_queue and iwl_wake_queue instead of the
mac80211 counterparts.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Reinette Chattre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When TX aggregation becomes operational, we do a number of steps:
1) print a debug message
2) wake the virtual queue
3) notify the driver
Unfortunately, 1) and 3) are only done if the driver is first to
reply to the aggregation request, it is, however, possible that the
remote station replies before the driver! Thus, unify the code for
this and call the new function ieee80211_agg_tx_operational in both
places where TX aggregation can become operational.
Additionally, rename the driver notification from
IEEE80211_AMPDU_TX_RESUME to IEEE80211_AMPDU_TX_OPERATIONAL.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
change the display of current driver status bit to user readable format
for better and easier debugging
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We shouldn't return NETDEV_TX_BUSY from the TX callback, especially
after we've mucked with the sk_buffs. Drop the packets and return
NETDEV_TX_OK.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch restores all-in-one module build procedure for ar9170.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were claiming DMA buffers on the RX tasklet but never
upon a simple module removal.
Cc: stable@kernel.org
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k sets up a mapping table from the hardware rate index to
the rate index used by mac80211; however, we have seen some
received frames with incorrect rate indexes. Such frames
normally get dropped with a warning in __ieee80211_rx(),
but it doesn't include enough information to track down the
error.
This patch adds a warning to hw_to_driver_rix for any lookups
that result in a rate index of -1, then returns a valid rate so
the frame can be processed.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the return type of b43_plcp_get_bitrate_idx_ofdm. If
the plcp contains an error, the function return value is 255 instead
of -1, and the packet was not dropped. This causes a warning in
__ieee80211_rx function because rate idx is out of range.
Cc: stable@kernel.org
Signed-off-by: Lorenzo Nava <navalorenx@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates p54's Kconfig entry and removes the out-dated device list.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch simplifies the tx_status report code by using four tx_queues per
station instead of only one. (the skb lookup should be in O(1) now :-p ).
Also, it fixes a really obvious copy&paste bug in the janitor work code and
adds back a few spilled bits to the hardware definition header about QoS.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add vendor ID for Quanta Microsystems and update the led table with the reported device.
Reported-by: Scott Barnes <nekoreeve@gmail.com>
Signed-off-by: Tulio Magno Quites Machado Filho <tuliom@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch update all necessary Makefile and Kconfig files.
Now you can then enable ar9170 in the kernel configuration under:
Device Drivers --->
[*] Network device support --->
Wireless LAN --->
[*] Wireless LAN (IEEE 802.11)
<M> Atheros AR9170 support
<M> Atheros AR9170 USB support
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
USB frontend driver code for Atheros' AR9170 modules.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch contains almost all mac80211 interaction code of AR9170.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hardware / firmware interface definitions for Atheros' AR9170 based devices.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Without this the regulatory domain isn't seen and we end up
intersecting for each request (each radio).
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables mesh point operation for ath9k. Tested with b43,
ath9k, rt2500usb, and ath5k as peers.
Signed-off-by: Pat Erley <pat-lkml@erley.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a compile problem when the MAC80211_LEDS
triggers are enabled but not LED class itself.
(which is sort of pointless, but anyway...)
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates count of every hw tried rate with
appropriate tries before reporting tx status of a frame.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This masks the PHY TX error interrupt, if debugging is disabled.
Currently we have a bug somewhere which triggers this interrupt once
in a while. (Depends on the network noise/quality). While this is nonfatal,
it scares the hell out of users and we frequently receive bugreports
that incorrectly identify this error message as the reason.
There's another problem with this. The PHY TX error interrupt is protected
with a watchdog that will restart the device if it keeps triggering very often.
This is used to fix interrupt storms from completely broken devices.
However, this watchdog might trigger in completely normal operation.
If the TX capacity of the card is saturated, the likeliness of the watchdog
triggering increases, as more TX errors occur. The current threshold
for the watchdog is 1000 errors in 15 seconds.
This patch adds a workaround for the issue by just enabling the interrupt
if debugging is disabled (by Kconfig or by modparam).
This has the downside that real fatal PHY TX errors are not caught anymore.
But this is nonfatal due to the following reasons:
* If the card is not able to transmit anymore, MLME will notice anyway.
* I did _never_ see a real fatal PHY TX error in a mainline b43 driver.
* It does _not_ result in interrupt storms or something like that.
It will simply result in a stalled card. It can be debugged by enabling
the debugging module parameter.
Signed-off-by: Michael Buesch <mb@bu3sch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We will miss rate control update if first A-MPDU of an
aggregation is not Block Acked as we always tell if the
rate control needs to updated through update_rc of first
A-MPDU. This patch does rate control update for the first
A-MPDU which notifies it's tx status (which is not
necessarily the first A-MPDU of an aggregation) to mac80211.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A *leftover* stations is replaced with stations_39.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fix related to bug 1921 at
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1921
when detect error during stopping tx aggregation queue, report the error to
help identify the problem.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Control the rate decrease. Do not decrease the rate fast.
Use success_ratio for rate scaling :)
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl_cmd_queue_free needs to be used to free up the cmd_queue,
as TFD slots for cmd_queue and tx_queue are different.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Total number of queues is 8 but only 7 of them are TX queues.
4 AC(Data) queue ,1 CMD and 2 HCCA. The HCCA queues are not used.
max_txq_num is set to maximum usable TX queues.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set IEEE80211_HW_SPECTRUM_MGMT bit in hw->flags, this tell mac80211
we support spectrum mgmt.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If user set new power level, accept the new power level and only
send command to host if the interface is up and radio on.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
allow user to set power level at all times
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When receive IEEE80211_AMPDU_RX_STOP or IEEE80211_AMPDU_TX_STOP request
in iwl_mac_ampdu_action() from mac80211; check STATUS_EXIT_PENDING bit,
if NIC is on the way out, then return 0 back to mac80211, this can
prevent mac80211 report HW error incorrectly.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In function iwl3945_mac_config use changed flag to call only
the affected functions.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In function iwl_mac_config use changed flag to call only
the affected functions. This patch also allow user to cache
channel, txpower and power value when the interface is not
ready and apply the changes once the interface ready.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add tx power calibration support
* Add a few tx power limits
* Hardcode default power to 12.5dB
* Disable TPC for now
v2: Address Jiri's comments
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the PCI retry timeout code, for all the same reasons that
Luis Rodriguez removed it for ath9k.
Changes-licensed-under: 3-Clause-BSD
Cc: Luis Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MIB interrupt fires whenever counters overflow; however without
support for automatic noise immunity, we can sometimes get an interrupt
storm. The get_stats() callback reads the counters anyway so we can
disable the interrupt for now until ANI is implemented. This fixes
the issue reported in http://bugzilla.kernel.org/show_bug.cgi?id=12647.
Changes-licensed-under: 3-Clause-BSD
Cc: stable@kernel.org
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Convert chip specific calibration data to a generic format common
for all chips
Note: We scale up power to be in 0.25dB units for all chips for
compatibility with RF5112
v2: Address Bob's and Jiri's comments
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Fix a typo in initvals.c so that we use the RF2425 array for RF2425 and not RF2413
Note: This also fixes incorect pd gain overlap since RF2425 has different pd gain overlap from RF2413
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>