I am resubmitting the 2.6 kernel patch for the Version 7.12.02 ips driver.
I have eliminated a couple of inappropriate changes pointed out by Arjan.
Signed-off-by: Jack Hammer <jack_hammer@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch does correct radio chip autodetection to avoid misdetecting
mt20xx microtune as tea5767 chip.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Martin Drab found that he could get aacraid timeouts with high load on his
controller / disk drive combinations. After some experimentation Mark
Salyzyn has come up with a patch to reduce the default max_sectors to
something that will keep the controller from being overloaded and will
eliminate the timeout issues.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Mark Salyzyn <mark_salyzyn@adaptec.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
cs89x0 talks a lot at boot. Seems like debug leftover. This patch
downgrades printks to KERN_DEBUG. While we're at it, make these messages a
bit less obscure.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The default resync_max_sector is set to "mddev->size << 1". If the
raid-personality-module updates mddev->size, it must update
resync_max_sectors too.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Peter Missel:
- Add support for the SVideo input on the GDI Black Gold.
Mauro Carvalho Chehab:
- Linux/version.h removed. Replaced by linux/utsname.h
Michael Krufky:
- Added analog support for DViCO FusionHDTV5 Gold.
CC: Peter Missel <peter.missel@onlinehome.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Fixed some bttv card numbers.
- BTTV and SAA7134 version numbers incremented to reflect changes.
- pci_dma_supported() is called after pci_set_dma_mask() which
already did check that for us. This patch removes the unneeded call to
pci_dma_supported() at bttv-driver.c
- Ensure a sufficient I2C bus idle time between 2 messages for
saa7134-i2c.c
- It is important to write at first to MO_GP3_IO for cx88-tvaudio.c
- Use try_to_freeze() instead of refrigerator at msp3400.c
- Recognizing the MFPE05-2 Tuner at tveeprom.c
- Add new parameter to help identify radio chipsets at tuner module:
show_i2c=1 will show 16 reading bytes from detected tuners.
- BTTV does generate some Unimplemented IOCTL log at tuner module:
0x40046d11(dir=1,tp=0x6d,nr=17,sz=4) means that it is sending
MSP3400 calls to non-msp3400 tuners. Warning eliminated.
VIDIOSAUDIO is also called, so debug messages updated. It is still
requiring IOCTL implementation.
- Added two more tuners.
- Add support for the SVideo input on the GDI Black Gold.
Signed-off-by: Peter Missel <peter.missel@onlinehome.de>
Signed-off-by: Graham Bevan <graham.bevan@ntlworld.com>
Signed-off-by: Torsten Seeboth <Torsten.Seeboth@t-online.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t.online.de>
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make it compile with CONFIG_PM=n
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Seems that both Greg and I submitted the same patch and it just kept on
applying...
Cc: Greg KH <greg@kroah.com>
Cc: Kumar Gala <galak@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If there are devices that use interrupts over a suspend event, ACPI must
restore the PCI interrupt links on resume. Anything else breaks any
device that hasn't been converted to the new (dubious) PM rules.
Drivers that need the irq free/re-aquire sequence can be done one by one
independently of this one.
Reported by: Jochen Hein (Bugzilla Bug 4312)
When there is disk I/O happening, the framebuffer has a little snow on
the screen. Once I/O has finished, no garbage remains on screen.
This bug was explained by: Knut Petersen
Most important is CRTC register 2f, signal quality is also improved for
higher vclk values by changing set_vclk() according to the X drivers and
cyblafb.c
The fix is to set the performance register (0x2f) with a more stable
value.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reported by: Jochen Hein (Bugzilla Bug 4386)
booting leaves the end of long lines in the last line on screen when
scrolling. When X is running, scrolling puts garbage on the screen
(looks like X data) Console switch fixes the screen. Behaviour seems to
be identical with noaccel and without on the video=tridentfb parameter
in lilo.conf.
This bug was explained by: Knut_Petersen
Acceleration is broken for all BLADE 3D chips for all versions of kernel
2.6 except for 32bit modes. Most important reason is that the u32 col
parameter of the graphics engine needs the color value replicated to all
u8 of the u32 (8bit modes) and to both u16 of the u32.
Fix color value passed to graphics engine, verified by the reporter.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The ordering of setting and clearing device_add_pending went wrong on some
occasions, causing multifunction cards only to be handled correctly on the
first insertion, not on subsequent ones.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Avoid registering PCMCIA CF cards before other IDE stuff. This means the risk
of /dev/hd* being re-ordered is lessened. The _sane_ thing to assert any
ordering is to use udev, nameif and so on, of course.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch displays the name of the fbdev driver in sysfs.
Down the road this will replace the current proc handle we have.
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Drivers really only work well in SMP if they actually can be selected.
This is a leftover from the time when the 6pack drive only used to be
a bitrotten variant of the slip driver.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Kconfig | 2 +-
1 files changed, 1 insertion(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
--ReaqsoxgOBHFXBhH
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
Hi Jeff,
Here's a little patch fixing a typo in smc91x.h.
Regards,
Tony
--ReaqsoxgOBHFXBhH
Content-Type: text/x-chdr; charset=us-ascii
Content-Disposition: inline; filename="patch-fix-typo-smc91x.h"
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Yukon-Lite chipset needs workaround for revision 7 (or later).
Without this patch, chip gets stuck in low power mode and never
boots. Newer SysKonnect vendor code already had same patch.
Related bug in skge is http://bugs.gentoo.org/87822
Chris, please add for 2.6.12.2
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
SCSI=m must disallow static drivers.
The problem is that all the SATA drivers depend on SCSI_SATA.
With SCSI=m and SCSI_SATA=y this allows the static enabling of the SATA
drivers with unwanted effects, e.g.:
- SCSI=m, SCSI_SATA=y, SCSI_ATA_ADMA=y
-> SCSI_ATA_ADMA is built statically but scsi/built-in.o is not linked
into the kernel
- SCSI=m, SCSI_SATA=y, SCSI_ATA_ADMA=y, SCSI_SATA_AHCI=m
-> SCSI_ATA_ADMA and libata are built statically but
scsi/built-in.o is not linked into the kernel,
SCSI_SATA_AHCI is built modular (unresolved symbols due to missing
libata)
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cleanup code that is used to toggle LED's. Since we
get called from ethtool, can use that thread rather than
setting up a timer.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
During autonegotiation set PHY interrupt mask to ignore
bogus speed change interrupts.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The code to clear fifo errors was incorrect and sending garbage
to the external phy. Removed the no longer used inline's funcs.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The check for Yukon lite changes was restricting itself to
rev A3. It turns out that these changes are also true on A4
and later.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cleanup the phy_lock deadlock because of relocking in the nway_reset path.
Reported by Francois Romieu.
Also, don't need to do irqsave/restore for blink,
just excluding bh is good enough.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Here is a fix for a typo, thanks Eliot Dresselhaus.
Since transmitter not active when device is down, it wasn't really noticed.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The SK-9E boards use the Marvell Yukon2 chipset which
is not supported by the skge driver. Thanks to Ralph Roesler
for noticing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Using Genesis board, I get harmless error reports. Rather than console
error, turn it into a error counter.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Replace Host AP version of WEP, TKIP, CCMP implementation with
net/ieee80211 that has more or less identical implementation (since
it is based on the Host AP implementation). Remove Host AP specific
implementation and modules from drivers/net/wireless/hostap.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Preparations for starting to use net/ieee80211 instead of private
IEEE 802.11 implementation. Include net/ieee80211.h and
net/ieee80211_crypt.h into files that will be needed these in the
future. Remove duplicate definitions from hostap_common.h and
rename WLAN_FC_GET_{TYPE,STYPE} macros for now sinc net/ieee80211.h
is using incompatible definitions. This will be resolved in the
future by updating Host AP to use the versions that do not shift
type/stype.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed beacon frame when moving from monitor mode to master mode
(workaround for firmware bug that left IBSS IE in the Beacon
frames). This is using the same workaround that was previously used
when moving from adhoc mode to master mode.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Warning fix for 64-bit platforms
Hello!
The patch fixes following warning seen on 64-bit platforms (in my case -
x86_64, gcc-4.0):
In file included from /usr/local/src/hostap/driver/modules/hostap_cs.c:203:
/usr/local/src/hostap/driver/modules/hostap_hw.c: In function ?prism2_transmit_cb?:
/usr/local/src/hostap/driver/modules/hostap_hw.c:1674: warning: cast from pointer to integer of different size
/usr/local/src/hostap/driver/modules/hostap_hw.c: In function ?prism2_transmit?:
/usr/local/src/hostap/driver/modules/hostap_hw.c:1758: warning: cast to pointer from integer of different size
prism2_transmit_cb uses a (void *) argument to get an integer. A
simple fix would be to use double cast from pointer to long and then to
int (and vice versa when int is passed as a pointer). But I prefer a
slightly longer patch.
I believe that whenever an argument can hold both a pointer and an
integer, it should be declared long. long can hold both pointers and
integers (except win64, but we are not coding for Windows), it can be
cast to both of them and it's never assumed to be a valid pointer, which
could be useful for some automatic code checkers.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
line 129 of hostap_80211_rx.c should read:
LWNG_SETVAL(mactime, 2, 0, 4, rx_stats->mac_time);
not:
LWNG_SETVAL(mactime, 2, 0, 0, rx_stats->mac_time);
The length field is incorrect.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Firmware seems to be getting into odd state in host_roaming mode 2
when hostscan is used without join command, so try to fix this by
re-joining the current AP. This does not actually trigger a new
association if the current AP is still in the scan results.
This makes background scans (iwlist wlan0 scan) not to break data
connection when in host_roaming 2 mode, e.g., when using wpa_supplicant.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cleaned up scan result processing by converting struct
hfa384x_scan_result into struct hfa384x_hostscan_result. This removes
special cases from result processing since the results are only used
in one, hostscan, format.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Added support for setting channel mask for scan requests
('iwpriv wlan0 scan_channels 0x00ff' masks scans to use channels 1-8).
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add MODULE_VERSION information for the Host AP kernel modules and
update the version string to indicate which version of the external
Host AP driver is included in the kernel tree.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
pcmcia id_table for hostap_cs.c
Hi Jouni,
Here's a patch for adding a pcmcia id_table to hostap_cs.c as introduced
by the PCMCIA subsystem changes in linux-2.6.13-rc1. The id_table allows
hotplug (along with pcmciautils [1]) to load the driver without the need
for the pcmcia-cs cardmgr daemon.
The id_table was generated from the CVS version of hostap_cs.conf using
a script borrowed from Dominik Brodowski. I have removed any duplicate
entries, but I have only been able to test the functionality of the
patch with a Linksys WPC11v3.
Sincerely,
Brix
[1]: http://www.kernel.org/pub/linux/utils/kernel/pcmcia/
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Create sysfs "device" files for hostap
I was writing some scripts to automatically build kismet source lines,
and I noticed that hostap devices don't have device files, unlike my
prism54 and ipw2200 cards:
$ ls -l /sys/class/net/eth0/device
/sys/class/net/eth0/device -> ../../../devices/pci0000:00/0000:00:1e.0/0000:02:01.0
$ ls -l /sys/class/net/wifi0
ls: /sys/class/net/wifi0/device: No such file or directory
$ ls -l /sys/class/net/wlan0
ls: /sys/class/net/wlan0/device: No such file or directory
The following (quite small) patch makes sure that both the wlan and wifi
net devices have that pointer to the bus device.
This way, I can do things like
for i in /sys/class/net/*; do
if ! [ -e $i/device/drive ]; then
continue;
fi;
driver=$(basename $(readlink $i/device/driver))
case $driver in
hostap*)
echo -- hostap,$i,$i-$driver
break;
ipw2?00)
echo -- $driver,$i,$i-$driver
break;
prism54)
echo prism54g,$i
esac
done
Which should generate a working set of source lines for kismet no matter
what order I plug the cards in.
It might also be handy to have a link between the two net devices, but
that's a patch for another day.
That patch is against 2.6.13-rc1-mm1.
-- Dave
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
hostap_cs: Remove irq_list, irq_mask and pcmcia/version.h
Remove irq_list, irq_mask and pcmcia/version.h as suggested in
http://kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
EXPORT_SYMTAB does nothing. There's no need to define something if it
doesn't have any effect.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Update hostap_cs to use new PCMCIA event callback registration.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
ACPI is wrong. Devices should not release their IRQ's on suspend and
re-aquire them on resume. ACPI should just re-init the IRQ controller
instead of breaking most drivers very subtly.
Breakage reported by Hugh Dickins <hugh@veritas.com>
Undo: d8c4b4195c
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
An early version of the sk98lin patch was merged via Len's tree. But there
were subsequent updates as a result of review from Jeff. THis fixes things
up.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Basically DT isn't reported or handled at all. The problem is that
lines of code like this:
spi_dt(starget) = tinfo->curr.ppr_options & MSG_EXT_PPR_DT_REQ;
don't do what you think they do when spi_dt is a single bit variable.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
drivers/fc4/fc.c: In function `fcp_scsi_dev_reset':
drivers/fc4/fc.c:933: warning: control reaches end of non-void function
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes srp.h which uses 0x80 for SRP_LOGIN_REJ instead of
0xc2.
Signed-off-by: Linda Xie <lxie@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add reference count and disable ACPI PCI Interrupt Link
when no device still uses it.
Warn when drivers have not released Link at suspend time.
http://bugzilla.kernel.org/show_bug.cgi?id=3469
Signed-off-by: David Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
EC burst mode benefits many machines, some of
them significantly. However, our current
implementation fails on some machines such
as Rafael's Asus L5D.
This patch restores the alternative EC polling code,
which can be enabled at boot time via "ec_polling"
http://bugzilla.kernel.org/show_bug.cgi?id=4665
Signed-off-by: Luming Yu <luming.yu@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When leaving S3 state, the AGP bridge may not have all PCI configuration
registers set in the same way as they were at boot. This should be fixed
by pci_restore_state - however, the APBASE register cannot be set to
conflict with the APSIZE register. If APSIZE is larger than it was before
suspend, pci_restore_state will not restore APBASE correctly. The attached
patch adds an extra item to the agp_bridge_data structure and uses it to
store the value of APBASE. On resume, this is then written after APSIZE
has been set. This patch only touches the path used for Intel chipsets
without integrated graphics, and may need to be extended to work with the
others.
Without this patch, I get the symptoms described in bug 4921 - APBASE ends
up overlapping various PCI devices, and as a result they fail to work after
resume.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Close a small window where a device may be not operational again after senseid
finished and the "same device" check fails due to dev=0000 by checking for dnv
after stsch() by then setting the device to not operational. (No need to
check for dnv in ccw_device_handle_oper() again since we don't do stsch() into
the subchannel's schib in the meantime and will get a crw anyway if the device
becomes not oper again).
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do not use memcpy in fb_pad_aligned_buffer. It is suboptimal because only
a few bytes are moved at a time. Replace with a for-loop.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
>> vesafb: mode is 800x600x16, linelength=1600, pages=16
>> vesafb: scrolling: redraw
>> vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
>> mtrr: type mismatch for fc000000,1000000 old: write-back new: write-
>> combining
Range is already set to write-back, vesafb attempts to add a write-combining
mtrr (default for vesafb).
>> mtrr: size and base must be multiples of 4 kiB
This is a bug, vesafb attempts to add a size < PAGE_SIZE triggering
the messages below.
To eliminate the warning messages, you can add the option mtrr:2 to add a
write-back mtrr for vesafb. Or just use nomtrr option.
1. Fix algorithm for finding the best power of 2 size with mtrr_add().
2. Add option to choose the mtrr type by extending the mtrr boot option:
mtrr:n where n
0 = no mtrr (equivalent to using the nomtrr option)
1 = uncachable
2 = write back
3 = write combining (default)
4 = write through
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for UARTs in MMIO space and clean up a little whitespace.
HP legacy-free ia64 machines need this.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It seems that I see a bug in hidinput_hid_event. The check for NULL can never
work, becaue &hidinput->input is nonzero at all times.
Cc: <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch does the same swap, i.e. use the ISO macro if (isoc).
Additionally, it fixes the return value - the usb_calc_bus_time function
returns the time in nanoseconds (I didn't notice that before) while the
HS_USECS and HS_USECS_ISO are microseconds. This fixes the function to
return nanoseconds always, and adjusts ehci-q.c (the only high-speed
caller of the function) to wrap the call in NS_TO_US().
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
USB (OHCI) Host driver for S3C2410/S3C2440 based systems
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Gigabyte GN-WLBZ201 wifi usb dongle works very well, using the zd1201
driver. the only missing part is that the corresponding usbid is not
declared. The following patch should fix this.
From: "Mathieu" <matt@minas-morgul.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch enables a support of KYOCERA AH-K3001V, one of the most
popular cell phone in Japan. This device has vendor specific ID but works
with acm driver by adding USB ID. This device already works on
FreeBSD and OS X by native USB ACM driver with USB ID added.
This device is probed as NO_UNION_NORMAL not to hang up when probing.
Signed-off-by: Masahito Omote <omote@utyuuzin.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch handles a rarely-encountered failure mode in usbcore. It's
legal for device_add to fail (although now it happens even more rarely
than before since failure to bind a driver is no longer fatal). So when
we destroy the interfaces in a configuration, we shouldn't try to delete
ones which weren't successfully registered. Also, failure to register an
interface shouldn't be fatal either -- I think; you may disagree about
this part of the patch.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The only uses of both variables were recently removed.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes an information leak in the usbfs snoop facility:
uninitialized data from __get_free_page can be returned to userspace and
written to the system log. It also improves the snoop output by printing
the wLength value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ftdi_sio: Fix timeouts in a couple of usb_control_msg() calls due to
change of units from jiffies to milliseconds in 2.6.12.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ftdi_sio: Update RTS and DTR simultaneously, using a single control URB
instead of separate control URBs for RTS and DTR. Reinhard Bergmann
observed time differences of up to 680 ms with his application on a
2.4.22 kernel when RTS and DTR were updated using separate control
URBs, which is unacceptable.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch adds the following new devices to the ftdi_sio driver:
* microHAM USB-Y6 and USB-Y8 devices submitted by Justin Burket (KL1RL).
* Evolution Robotics ER1 Control Module submitted by Shawn M. Lavelle.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The setup-bus code doesn't work correctly for configurations
with more than one display adapter in the same PCI domain.
This stuff actually is a leftover of an early 2.4 PCI setup code
and apparently it stopped working after some "bridge_ctl" changes.
So the best thing we can do is just to remove it and rely on the fact
that any firmware *has* to configure VGA port forwarding for the boot
display device properly.
But then we need to ensure that the bus->bridge_ctl will always
contain valid information collected at the probe time, therefore
the following change in pci_scan_bridge() is needed.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are ROMs reporting that their size exceeds their PCI ROM
resource window. This patch returns the minimum of the resource window
size or the size in the ROM. An example of this breakage is the XGI
Volari Z7.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch was sent first time very long time ago,
but magically was disapeared, it probably exists
in your queue, but to be sure, I resend it.
If can not be applied cleanly after your w1 queue is flushed
into upstrem tree, just drop it.
Thanks.
Patch from Michael Farmbauer <michl@baldrian.franken.de>.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The 24RF08 corruption prevention in the eeprom and max6875 drivers wasn't
complete. For one thing, the additional quick write should happen as soon
as possible and unconditionally, while both drivers had error paths before.
For another, when a given chip is forced, the core does not emit a quick
write, so a second quick write would cause the corruption rather than
prevent it.
I plan to move the corruption prevention in the core in the long run, so
that individual drivers don't have to care anymore. But I need to merge
i2c_probe and i2c_detect before I do (work in progress).
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Two log messages lack their trailing new line in i2c-core. I'd swear I had
fixed them already, but it seems not. Bonus: improved coding style.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A few i2c drivers were not updated to use time_after() yet.
Signed-off-by: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A few split string in i2c (and now hwmon) drivers lack a joining space,
causing them to display incorrectly. This trivial patch fixes that up.
Please apply, thanks.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
DS1339 manual, page 6, chapter Date and time operation:
The DS1339 can be run in either 12-hour or 24-hour mode. Bit 6 of the
hours register is defined as the 12-hour or 24-hour mode-select bit.
When high, the 12-hour mode is selected.
Patch below makes ds1337 driver work as documented in manual.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I2C-MPC: Restore code removed
A previous patch to remove support for the OCP device model was way
to generious and moved some of the platform device model code, oops.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
where C-states come from FADT.
Thanks to Kevin Radloff for identifying the issue and
isolating it to exact line of code that is causing the issue.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch is an attempt to fix deadlocks discovered in the core dm.
The problems boil down to md->lock having to be held in too many places, so
I've split it into two: md->suspend_lock and md->io_lock.
suspend_lock is now held throughout dm_suspended() as well as dm_resume()
and dm_swap_table() so that these functions cannot run concurrently:
there's no requirement for that and it added complexity.
DMF_FS_LOCKED becomes redundant: DMF_SUSPENDED provides adequate
protection.
Signed-Off-By: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Avoid another bdget_disk which can deadlock.
Signed-Off-By: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some code tidy-ups in preparation for the next patches. Change
dm_table_pre/postsuspend_targets to accept NULL. Use dm_suspended()
throughout.
Signed-Off-By: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
RARP replies are another valid case where IPoIB may need to send a
unicast packet with no neighbour structure.
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Reject code 24 is port and CM redirection, not just port redirection.
Port redirection alone is code 25.
Therefore we should rename code 24 to IB_CM_REJ_PORT_CM_REDIRECT and
use IB_CM_REJ_PORT_REDIRECT for code 25.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch adds functionality to check the PCI sub-class code of an
AHCI capable device before disabling AHCI. It fixes a bug where an
ICH7 sata controller is being setup by the BIOS as sub-class 1 (ide)
and the AHCI control registers weren't being initialized, thus causing
an IO error in piix_disable_ahci().
Signed-off-by: Gregory Felix <greg.felix@gmail.com>
* ret has no need to be unsigned in cpufreq_driver_target()
* ret has no need to be initialized in __cpufreq_governor()
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dave Jones <davej@redhat.com>
If the PCDP supplies parity, use it (only none/even/odd supported), and
don't append parity/stop bit arguments unless baud is present.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sys_reboot() now calls device_suspend(), so it is no longer necessary for
the e1000 driver to register a reboot notifier [in fact doing so results in
e1000_suspend() getting called twice].
(akpm: we need to fast-track this. It's causing ia64 to oops on shutdown)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: <cramerj@intel.com>
Cc: <john.ronciak@intel.com>
Cc: <ganesh.venkatesan@intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds per disk queue functionality to cciss. Sometime back I
submitted a patch but it looks like only part of what I needed. In the 2.6
kernel if we have more than one logical volume the driver will Oops during
rmmod. It seems all of the queues actually point back to the same queue.
So after deleting the first volume you hit a null pointer on the second
one.
This has been tested in our labs. There is no difference in performance,
it just fixes the Oops.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Older O2Micro bridges have problems with both read prefetch and write burst
depending on the combination of the chipset, bridge, cardbus card. safest is
to disable read prefetch and write burst on those old bridges.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Debugging and description from: Noah Misch <noah@cs.caltech.edu>
When a driver calls pcmcia_request_irq with IRQ_HANDLE_PRESENT unset, it looks
for an open IRQ by request_irq()ing with a dummy handler and NULL dev_info.
free_irq uses dev_info as a key for identifying the handler to free among
those sharing an IRQ, so request_irq returns -EINVAL if dev_info is NULL and
the IRQ may be shared. That unknown error code is the -EINVAL.
It looks like only pcnet_cs and axnet_cs are affected. Most other drivers let
pcmcia_request_irq install their interrupt handlers. sym53c500_cs requests
its IRQ manually, but it cannot share an IRQ.
The appended patch changes pcmcia_request_irq to pass an arbitrary, unique,
non-NULL dev_info with the dummy handler.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the product-id-string contains the '+' , '&' ,'_', it was not converted
properly from the /etc/pcmcia/config(pcmcia-cs config file).
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Avoid double iounmap of one address, and disable cis_virt if set_mem_map
failed.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Get the au1000 PCMCIA socket drivers to work.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove duplicates from the device id table.
Signed-off-by: Jarkko Raja <jar@pcuf.fi>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are two problems with the message about missing callback functions: it's
not written in correct English and it lacks newline at the end.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SanDisk ConnectPlus has two functions. Function 0 is prism2 card, currently
only supported by HostAP (not in the kernel). Function 1 is 128M flash,
supported by ide-cs. This patch adds an entry for function 1 to ide-cs.c.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds the appropriate FW_LOADER pre-requisite and a separate entry
for ISP24xx support.
Thanks to Adrian Bunk and Jesper Juhl for their efforts in fixing this
quirk.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Only print debug messages when debug_level is set.
Eliminate NULL checks prior to calling kfree.
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Libor Michalek <libor@topspin.com>
If we haven't configured the qla24xx driver, then the Makefile shouldn't
do it for us.
This also means that we can avoid the unnecessary selection of FC_ATTRS.
Debugged by James Bottomley
a) update entry in CREDITS for Jesper Juhl
b) remove email address from source files so it's only listed in credits.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
`gcc -W' likes to complain if the static keyword is not at the beginning of
the declaration. This patch fixes all remaining occurrences of "inline
static" up with "static inline" in the entire kernel tree (140 occurrences in
47 files).
While making this change I came across a few lines with trailing whitespace
that I also fixed up, I have also added or removed a blank line or two here
and there, but there are no functional changes in the patch.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The fb_info struct, as defined in include/linux/fb.h, contains an element
that is supposed to hold the current color map:
struct fb_cmap cmap; /* Current cmap */
This cmap is currently never updated when either fb_set_cmap() or
fb_set_user_cmap() are called. As a result, info->cmap contains the
default cmap that was set by a device driver/fbcon and a userspace
application using the FBIOGETCMAP ioctl will not always get the *currently*
used color map.
The patch fixes this by making sure the cmap is copied to info->cmap after
it is set correctly. It moves most of the code that is responsible for
setting the cmap to fb_set_cmap() and out of fb_set_user_cmap() to avoid
code-duplication.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Cc: <linux-fbdev-devel@lists.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently even when the cursor is disabled (`setterm -cursor off`), it is
still repainted as a black rectangle the size of a single char. This can
be seen, for example, by chvt'ing to a free tty, disabling the cursor and
doing `dd if=3D/dev/urandom of=3D/dev/fb0`.
The patch changes this behaviour by avoiding painting anything when the
cursor is disabled.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Cc: <linux-fbdev-devel@lists.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Color maps have up to 256 entries. 4096/256 allows for 16 characters per
line. The format for a cmap entry is "%02x%c%4x%4x%4x\n" %02x entry %c
transp %4x red %4x blue %4x green
You can read the color_map with cat fb0/color_map.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
radeonfb does not clean up EDID sysfs attribute
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
fbdev is missing unregister_chrdev() on unload.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix rounding error when mode frequency is very close to monitor limit
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
m8xx_cpm_hostalloc() can't rely on using the coherent DMA allocator early
on boot because the VM is not fully up yet. Change it to use the on-board
DPRAM instead.
The current code relies on the "bootmem_page" allocated by
m8xx_cpm_reset(), which must be killed.
This is done in v2.4 but has never been forward ported to v2.6.
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Cc: Pantelis Antoniou <panto@intracom.gr>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rename lgdt3302 to lgdt330x, to make way for the addition of lgdt3303
support in future revisions.
I am changing the name of this module now so that hopefully the name will
be changed before the release of 2.6.13 ... It wouldn't make sense to
release 2.6.13 with the name lgdt3302 in it, which will only be renamed to
lgdt330x in later versions.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I noticed that some past changes to the gerneric Video4Linux tuner module
for analog tuners broke my "Multimedia eXtension Board" driver.
The tuner driver was made aware of Video4Linux2 tuning ioctls, but my
driver was not ported and still uses the Video4Linux1 ioctls. This does
not work anymore as intendend, the tuning is currently broken.
The attached patch fixes non-working tuning in MXB driver introduced by
some recent generic tuner changes by replacing Video4Linux1 tuner ioctls
with proper Video4Linux2 tuner ioctls.
- fix non-working tuning in MXB driver introduced by some recent generic
tuner changes by replacing Video4Linux1 tuner ioctls with proper
Video4Linux2 tuner ioctls
Signed-off-by: Michael Hunold <hunold@linuxtv.org>
Cc: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The #define CONFIG_DVB_* are actually CFLAGS set by Makefile. CONFIG_*
namespace is reserved for Kconfig. This renames them back to HAVE_*
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch moves #define from cx88-dvb.c and saa7134-dvb.c into Makefile as
CFLAGS, allowing code compatability with video4linux cvs.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a missing #ifdef to saa7134-dvb.c (thanks to Mauro Carvalho
Chehab) and changes #if to #ifdef in both files.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
warning: `i2c_readbytes' defined but not used
This code will either be re-enabled or deleted in a future patch.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Select the RF input connector based upon the type of demodulation selected.
ANT RF connector is selected for 8-VSB and CABLE RF connector is selected
for QAM64/QAM256. This only affects the cards that use the Microtune 4042
tuner.
Signed-off-by: Mac Michaels <wmichaels1@earthlink.net>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the dvb_pll_desc from the frontend and replace with a
pll_set-callback to isolate the tuner programming from the frontend.
Signed-off-by: Mac Michaels <wmichaels1@earthlink.net>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove redundant bttv_reset_audio() which caused the computer to freeze
with some bt8xx based DVB cards when loading the bttv driver.
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
VIDEO_SAA7134=y and SOUND=n results in the following compile error:
LD .tmp_vmlinux1
drivers/built-in.o(.text+0x4fafcb): In function `saa7134_initdev':
: undefined reference to `unregister_sound_dsp'
drivers/built-in.o(.text+0x4fb141): In function `saa7134_initdev':
: undefined reference to `register_sound_dsp'
drivers/built-in.o(.text+0x4fb17c): In function `saa7134_initdev':
: undefined reference to `register_sound_mixer'
drivers/built-in.o(.text+0x4fb339): In function `saa7134_finidev':
: undefined reference to `unregister_sound_mixer'
drivers/built-in.o(.text+0x4fb341): In function `saa7134_finidev':
: undefined reference to `unregister_sound_dsp'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the following possible cleanups:
- make two needlessly global structs static
- #if 0 the EXPORT_SYMBOL'ed but unused function tveeprom_dump
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is a small modification to the table that defines the way that the
LG-Z201 tuner is controlled for the DVICO Fusion DVB-T1 tuner card.
I believe that a mistake was made when the dvb tuner code was reorganised
(to use a generic table for the tuner information instead of inline code)
and as a result, the DVICO card doesn't tune properly.
The modification I have made to the table makes it behave like it did with
the old inline tuner code that worked. The patch is on top of the 2.6.12
kernel.
Signed-off-by: Gregory B Frost <frosts1@hotkey.net.au>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Eliminate sparse warnings in SA client
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hook up userspace CM to the make system
Signed-off-by: Libor Michalek <libor@topspin.com>
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Include the patch openib-general changing class_simple to class.
Signed-off-by: Tom Duffy <tduffy@sun.com>
Cc: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add kernel portion of user CM implementation
Signed-off-by: Libor Michalek <libor@topspin.com>
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the header file for user space CM. This file defines the ABI used by the
CM for kernel/user communication.
Signed-off-by: Libor Michalek <libor@topspin.com>
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implementation for RMPP support in user MAD
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
User MAD ABI changes to support RMPP
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
