Some bits for zone reclaim exists in 2.6.15 but they are not usable. This
patch fixes them up, removes unused code and makes zone reclaim usable.
Zone reclaim allows the reclaiming of pages from a zone if the number of
free pages falls below the watermarks even if other zones still have enough
pages available. Zone reclaim is of particular importance for NUMA
machines. It can be more beneficial to reclaim a page than taking the
performance penalties that come with allocating a page on a remote zone.
Zone reclaim is enabled if the maximum distance to another node is higher
than RECLAIM_DISTANCE, which may be defined by an arch. By default
RECLAIM_DISTANCE is 20. 20 is the distance to another node in the same
component (enclosure or motherboard) on IA64. The meaning of the NUMA
distance information seems to vary by arch.
If zone reclaim is not successful then no further reclaim attempts will
occur for a certain time period (ZONE_RECLAIM_INTERVAL).
This patch was discussed before. See
http://marc.theaimsgroup.com/?l=linux-kernel&m=113519961504207&w=2http://marc.theaimsgroup.com/?l=linux-kernel&m=113408418232531&w=2http://marc.theaimsgroup.com/?l=linux-kernel&m=113389027420032&w=2http://marc.theaimsgroup.com/?l=linux-kernel&m=113380938612205&w=2
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Migration code currently does not take a reference to target page
properly, so between unlocking the pte and trying to take a new
reference to the page with isolate_lru_page, anything could happen to
it.
Fix this by holding the pte lock until we get a chance to elevate the
refcount.
Other small cleanups while we're here.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some people apparently run CONFIG_NUMA without CONFIG_SWAP. The migration
code currently depends on swap. This patch provides a set of inline
fallback functions so that the kernel properly compiles. However, calls to
migration functions will fail.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Extend the parameters of migrate_pages() to allow the caller control over the
fate of successfully migrated or impossible to migrate pages.
Swap migration and direct migration will have the same interface after this
patch so that patches can be independently applied to the policy layer and the
core migration code.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add gfp_mask to add_to_swap
add_to_swap does allocations with GFP_ATOMIC in order not to interfere with
swapping. During migration we may have use add_to_swap extensively which may
lead to out of memory errors.
This patch makes add_to_swap take a parameter that specifies the gfp mask.
The page migration code can then make add_to_swap use GFP_KERNEL.
Signed-off-by: Hirokazu Takahashi <taka@valinux.co.jp>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move move_to_lru, putback_lru_pages and isolate_lru in section surrounded by
CONFIG_MIGRATION saving some codesize for single processor kernels.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Include page migration if the system is NUMA or having a memory model that
allows distinct areas of memory (SPARSEMEM, DISCONTIGMEM).
And:
- Only include lru_add_drain_per_cpu if building for an SMP system.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds the basic page migration function with a minimal implementation that
only allows the eviction of pages to swap space.
Page eviction and migration may be useful to migrate pages, to suspend
programs or for remapping single pages (useful for faulty pages or pages with
soft ECC failures)
The process is as follows:
The function wanting to migrate pages must first build a list of pages to be
migrated or evicted and take them off the lru lists via isolate_lru_page().
isolate_lru_page determines that a page is freeable based on the LRU bit set.
Then the actual migration or swapout can happen by calling migrate_pages().
migrate_pages does its best to migrate or swapout the pages and does multiple
passes over the list. Some pages may only be swappable if they are not dirty.
migrate_pages may start writing out dirty pages in the initial passes over
the pages. However, migrate_pages may not be able to migrate or evict all
pages for a variety of reasons.
The remaining pages may be returned to the LRU lists using putback_lru_pages().
Changelog V4->V5:
- Use the lru caches to return pages to the LRU
Changelog V3->V4:
- Restructure code so that applying patches to support full migration does
require minimal changes. Rename swapout_pages() to migrate_pages().
Changelog V2->V3:
- Extract common code from shrink_list() and swapout_pages()
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: "Michael Kerrisk" <mtk-manpages@gmx.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the start of the `swap migration' patch series.
Swap migration allows the moving of the physical location of pages between
nodes in a numa system while the process is running. This means that the
virtual addresses that the process sees do not change. However, the system
rearranges the physical location of those pages.
The main intent of page migration patches here is to reduce the latency of
memory access by moving pages near to the processor where the process
accessing that memory is running.
The patchset allows a process to manually relocate the node on which its
pages are located through the MF_MOVE and MF_MOVE_ALL options while
setting a new memory policy.
The pages of process can also be relocated from another process using the
sys_migrate_pages() function call. Requires CAP_SYS_ADMIN. The migrate_pages
function call takes two sets of nodes and moves pages of a process that are
located on the from nodes to the destination nodes.
Manual migration is very useful if for example the scheduler has relocated a
process to a processor on a distant node. A batch scheduler or an
administrator can detect the situation and move the pages of the process
nearer to the new processor.
sys_migrate_pages() could be used on non-numa machines as well, to force all
of a particualr process's pages out to swap, if someone thinks that's useful.
Larger installations usually partition the system using cpusets into sections
of nodes. Paul has equipped cpusets with the ability to move pages when a
task is moved to another cpuset. This allows automatic control over locality
of a process. If a task is moved to a new cpuset then also all its pages are
moved with it so that the performance of the process does not sink
dramatically (as is the case today).
Swap migration works by simply evicting the page. The pages must be faulted
back in. The pages are then typically reallocated by the system near the node
where the process is executing.
For swap migration the destination of the move is controlled by the allocation
policy. Cpusets set the allocation policy before calling sys_migrate_pages()
in order to move the pages as intended.
No allocation policy changes are performed for sys_migrate_pages(). This
means that the pages may not faulted in to the specified nodes if no
allocation policy was set by other means. The pages will just end up near the
node where the fault occurred.
There's another patch series in the pipeline which implements "direct
migration".
The direct migration patchset extends the migration functionality to avoid
going through swap. The destination node of the relation is controllable
during the actual moving of pages. The crutch of using the allocation policy
to relocate is not necessary and the pages are moved directly to the target.
Its also faster since swap is not used.
And sys_migrate_pages() can then move pages directly to the specified node.
Implement functions to isolate pages from the LRU and put them back later.
This patch:
An earlier implementation was provided by Hirokazu Takahashi
<taka@valinux.co.jp> and IWAMOTO Toshihiro <iwamoto@valinux.co.jp> for the
memory hotplug project.
From: Magnus
This breaks out isolate_lru_page() and putpack_lru_page(). Needed for swap
migration.
Signed-off-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds the function get_swap_page_of_type() allowing us to specify an index
in swap_info[] and select a swap_info_struct structure to be used for
allocating a swap page.
This function (or another one of similar functionality) will be necessary for
implementing the image-writing part of swsusp in the user space. It can also
be used for simplifying the current in-kernel implementation of the
image-writing part of swsusp.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the last bits of Martin's ill-fated sys_set_zone_reclaim().
Cc: Martin Hicks <mort@wildopensource.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some users (hi Zwane) have seen a problem when running a workload that
eats nearly all of physical memory - th system does an OOM kill, even
when there is still a lot of swap free.
The problem appears to be a very big task that is holding the swap
token, and the VM has a very hard time finding any other page in the
system that is swappable.
Instead of ignoring the swap token when sc->priority reaches 0, we could
simply take the swap token away from the memory hog and make sure we
don't give it back to the memory hog for a few seconds.
This patch resolves the problem Zwane ran into.
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- added typedef unsigned int __nocast gfp_t;
- replaced __nocast uses for gfp flags with gfp_t - it gives exactly
the same warnings as far as sparse is concerned, doesn't change
generated code (from gcc point of view we replaced unsigned int with
typedef) and documents what's going on far better.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The idea of a swap_device_lock per device, and a swap_list_lock over them all,
is appealing; but in practice almost every holder of swap_device_lock must
already hold swap_list_lock, which defeats the purpose of the split.
The only exceptions have been swap_duplicate, valid_swaphandles and an
untrodden path in try_to_unuse (plus a few places added in this series).
valid_swaphandles doesn't show up high in profiles, but swap_duplicate does
demand attention. However, with the hold time in get_swap_pages so much
reduced, I've not yet found a load and set of swap device priorities to show
even swap_duplicate benefitting from the split. Certainly the split is mere
overhead in the common case of a single swap device.
So, replace swap_list_lock and swap_device_lock by spinlock_t swap_lock
(generally we seem to prefer an _ in the name, and not hide in a macro).
If someone can show a regression in swap_duplicate, then probably we should
add a hashlock for the swap_map entries alone (shorts being anatomic), so as
to help the case of the single swap device too.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
get_swap_page has often shown up on latency traces, doing lengthy scans while
holding two spinlocks. swap_list_lock is already dropped, now scan_swap_map
drop swap_device_lock before scanning the swap_map.
While scanning for an empty cluster, don't worry that racing tasks may
allocate what was free and free what was allocated; but when allocating an
entry, check it's still free after retaking the lock. Avoid dropping the lock
in the expected common path. No barriers beyond the locks, just let the
cookie crumble; highest_bit limit is volatile, but benign.
Guard against swapoff: must check SWP_WRITEOK before allocating, must raise
SWP_SCANNING reference count while in scan_swap_map, swapoff wait for that to
fall - just use schedule_timeout, we don't want to burden scan_swap_map
itself, and it's very unlikely that anyone can really still be in
scan_swap_map once swapoff gets this far.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The swap header's unsigned int last_page determines the range of swap pages,
but swap_info has been using int or unsigned long in some cases: use unsigned
int throughout (except, in several places a local unsigned long is useful to
avoid overflows when adding).
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The "Adding %dk swap" message shows the number of swap extents, as a guide to
how fragmented the swapfile may be. But a useful further guide is what total
extent they span across (sometimes scarily large).
And there's no need to keep nr_extents in swap_info: it's unused after the
initial message, so save a little space by keeping it on stack.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are several comments that swap's extent_list.prev points to the lowest
extent: that's not so, it's extent_list.next which points to it, as you'd
expect. And a couple of loops in add_swap_extent which go all the way through
the list, when they should just add to the other end.
Fix those up, and let map_swap_page search the list forwards: profiles shows
it to be twice as quick that way - because prefetch works better on how the
structs are typically kmalloc'ed? or because usually more is written to than
read from swap, and swap is allocated ascendingly?
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sparc can not include linux/pagemap.h because of the following circular
dependency:
asm-sparc/pgtable include linux/swap.h
linux/swap.h include now linux/pagemap.h
linux/pagemap.h include linux/mm.h
linux/mm.h include asm/pgtable.h
It needs to have the swp_entry_t type fully visible in pgtable.h,
we can't work around this using macros.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: William Lee Irwin III <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
free_pages_and_swap_cache() and free_page_and_swap_cache() use release_pages()
and page_cache_release() respectively, so make sure that we have the
declarations in scope.
Cc: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
try_to_free_pages accepts a third argument, order, but hasn't used it since
before 2.6.0. The following patch removes the argument and updates all the
calls to try_to_free_pages.
Signed-off-by: Darren Hart <dvhltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the core of the (much simplified) early reclaim. The goal of this
patch is to reclaim some easily-freed pages from a zone before falling back
onto another zone.
One of the major uses of this is NUMA machines. With the default allocator
behavior the allocator would look for memory in another zone, which might be
off-node, before trying to reclaim from the current zone.
This adds a zone tuneable to enable early zone reclaim. It is selected on a
per-zone basis and is turned on/off via syscall.
Adding some extra throttling on the reclaim was also required (patch
4/4). Without the machine would grind to a crawl when doing a "make -j"
kernel build. Even with this patch the System Time is higher on
average, but it seems tolerable. Here are some numbers for kernbench
runs on a 2-node, 4cpu, 8Gig RAM Altix in the "make -j" run:
wall user sys %cpu ctx sw. sleeps
---- ---- --- ---- ------ ------
No patch 1009 1384 847 258 298170 504402
w/patch, no reclaim 880 1376 667 288 254064 396745
w/patch & reclaim 1079 1385 926 252 291625 548873
These numbers are the average of 2 runs of 3 "make -j" runs done right
after system boot. Run-to-run variability for "make -j" is huge, so
these numbers aren't terribly useful except to seee that with reclaim
the benchmark still finishes in a reasonable amount of time.
I also looked at the NUMA hit/miss stats for the "make -j" runs and the
reclaim doesn't make any difference when the machine is thrashing away.
Doing a "make -j8" on a single node that is filled with page cache pages
takes 700 seconds with reclaim turned on and 735 seconds without reclaim
(due to remote memory accesses).
The simple zone_reclaim syscall program is at
http://www.bork.org/~mort/sgi/zone_reclaim.c
Signed-off-by: Martin Hicks <mort@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
