* No internal function uses const ata_port. Drop const from @ap.
* Make ata_acpi_stm() copy @stm before using it and change @stm to
const.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Improve the existing boot/load time warnings from sata_mv
for Highpoint RocketRAID 23xx cards, based on new knowledge
about where the BIOS likes to overwrite sectors with metadata.
Harmless to us, but very useful for end users.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Like ST380817AS / 3.42, ST3160023AS / 3.42 times out commands if NCQ
is used. Blacklist it. This is reported by Matheus Izvekov in the
following thread.
http://thread.gmane.org/gmane.linux.ide/24202
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Matheus Izvekov <mizvekov@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
link->eh_info.serror is used to cache SError for controllers which
need it cleared from interrupt handler to clear IRQ. It also should
be cleared after reset just like SError itself.
Make ata_std_postreset() clear link->eh_info.serror too and update
sata_sil such that it doesn't care about bookkeeping the value.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Interestingly, sata_sil raises spurious interrupts if it's coupled
with Sil SATA_PATA bridge. Currently, sata_sil interrupt handler is
strict about spurious interrupts and freezes the port when it occurs.
This patch makes it more forgiving.
* On SATA PHY event interrupt, serror value is checked to see whether
it really is PHYRDY CHG event. If not, SATA PHY event interrupt is
ignored.
* If ATA interrupt occurs while no command is in progress, it's
cleared and ignored.
This fixes bugzilla bug 9505.
http://bugzilla.kernel.org/show_bug.cgi?id=9505
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The patch fixes the STATUS_RF_KILL_HW state is not cleared problem if the
device goes to suspend when the rf_kill switch is enabled. The bug causes
the driver always thinks the rf_kill switch is enabled (although it is
disabled) after resume.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes Bug #9414
Since addition of the rfkill callback, the LED associated with the off
switch on the radio has not worked for several reasons:
(1) Essential data in the rfkill structure were missing.
(2) The rfkill structure was initialized after the LED initialization.
(3) There was a minor memory leak if the radio LED structure was inited.
Once the above problems were fixed, additional difficulties were noted:
(4) The radio LED was in the wrong state at startup.
(5) The radio switch had to be manipulated twice for each state change.
(6) A circular mutex locking situation existed.
(7) If rfkill-input is built as a module, it is not automatically loaded.
This patch fixes all of the above.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ia64:
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c: In function `tsf_write_file':
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:237: warning: long long int format, u64 arg (arg 3)
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:237: warning: long long int format, u64 arg (arg 3)
We do not know what type was used to implement u64 and we can never use u64 in
printk(), sscanf(), etc.
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure that libertas selects WIRELESS_EXT, since selecting other stuff that
should depend on WEXT, like IEEE80211, doesn't seem to drag that in for us.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix rate control algo reference leak in case if network device has been
failed to register. In this case special flag priv->mac80211_registered is
not set and the rate algo reference is not freeing on module unload. That
leads to OOPs in further ieee80211 rate register/unregister procedure (by
any callee).
It should fix the bug #9470http://bugzilla.kernel.org/show_bug.cgi?id=9470
[akpm@linux-foundation.org: build fix]
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Shaddy Baddah found an alignment problem with zd1211rw driver at
2007-11-19. This patch fixes it, it is based on the patch proposed by
Herbert Xu. The alignment 4 has been the agreed value on the
linux-wireless mailing list.
Notify that the problem does only affect the old zd1211rw softmac
driver and not the zd1211rw-mac80211 driver. Daniel Drake has
already provided a patch for the replacement of the softmac
driver, which this patch will break.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6:
HOWTO: update misspelling and word incorrected
add stable_api_nonsense.txt in korean
HOWTO: change addresses of maintainer and lxr url for Korean HOWTO
Add Documentation for FAIR_USER_SCHED sysfs files
HOWTO: Change man-page maintainer address for Japanese HOWTO
tipar: remove obsolete module
kobject: fix the documentation of how kobject_set_name works
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: revert portions of "UNUSUAL_DEV: Sync up some reported devices from Ubuntu"
usb: Remove broken optimisation in OHCI IRQ handler
USB: at91_udc: correct hanging while disconnecting usb cable
USB: use IRQF_DISABLED for HCD interrupt handlers
USB: fix locking loop by avoiding flush_scheduled_work
usb.h: fix kernel-doc warning
USB: option: Bind to the correct interface of the Huawei E220
USB: cp2101: new device id
usb-storage: Fix devices that cannot handle 32k transfers
USB: sierra: fix product id
Check in sis190_rx_interrupt() is broken on big-endian
(desc->status is little-endian and everything else actually uses
it correctly, including other checks for OWNbit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Commit ed7e63a51d has tried to fix
section mismatch:
WARNING: vmlinux.o(.init.text+0x17278): Section mismatch: reference to
.exit.text:uec_mdio_exit (between 'ucc_geth_init' and 'uec_mdio_init')
But that mismatch still happens.
This patch actually fixing section mismatch by removing __exit from
the header file.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This reverts one change from 67fa10627e
that prevented userspace from seing the "driver disk" lun in a san disk
device. The kernel shouldn't do this, it's up to userspace to handle
this properly, if it somehow wants to filter this away.
Cc: Ben Collins <bcollins@ubuntu.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The OHCI IRQ handler has an optimisation that avoids reading some
chip registers when the controller reports that the interrupt was
triggered *only* because completed requests were written into the
controller's "done list" and handed to the host.
This mechanism can't be used on some controllers. Among others, it
fails for the SA1111 and the AMCC 440EP PowerPC processor.
This patch removes the optimisation and makes the code clearer.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Correct hanging while disconnecting the USB device cable. Prevent a race
between vbus and UDP interrupts. This bug was tracked on at91sam9260ek
boards.
A usb resume interrupt was firing after the vbus interrupt : the IP was
then already stoped and not able to deal with it (no more clock). A simple
interrupt disabling is ok as the "end of bus reset" irq is non maskable and
ok to resume the USB device IP.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Host controller IRQs are supposed to be serviced with interrupts
disabled. This patch (as1026) adds an IRQF_DISABLED flag to all the
controller drivers that lack it. It also replaces the
spin_lock_irqsave() and spin_unlock_irqrestore() calls in uhci_irq()
with simple spin_lock() and spin_unlock().
This fixes Bugzilla #9335.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1027) replaces a call to flush_scheduled_work() -- a
dangerous routine to invoke, especially while holding any sort of lock
-- with calls to cancel_work_sync() and cancel_delayed_work_sync().
This fixes Bugzilla #9532.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a bunch of problems we are having with the Huawei devices...
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jaime Velasco Juan <jsagarribay@gmail.com>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds a device ID for the Aerocomm Radio Modem, which uses the
cp2102. I'm sure changing num_bulk_in/num_bulk_out to NUM_DONT_CARE
is the wrong fix, but this is the only device I have with a cp2102,
so I have no idea what a good global value would be, if there is one.
Zero didn't work with this device.
From: Jeff Long <JeffLong@mitre.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a device cannot handle the smallest previously limited transfer
size (64 blocks) without stalling, limit the device to the amount of
packets that fit in a platform native page.
The lowest possible limit is PAGE_CACHE_SIZE, so if the device is ever
used on a platform that has larger than 8K pages, you lose unless you
can convince the device firmware folks to fix the issue.
Cc: Mathew Dharm <mdharm-scsi@one-eyed-alien.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Doug Maxey <dwm@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Attached is a patch to fix the addition of the new product ids I sent.
It is against 2.6.24-rc4, as Linus included the broken version of the
patch I sent you in that tree. :(
Not sure if this is the right method to go about this, but hopefully I got
it right this time.
Signed-off-by: Andrew Gilmore <agilmore@wirelessbeehive.com>
CC: Kevin Lloyd <klloyd@sierrawireless.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Restore PCI expansion ROM P2P prefetch window creation.
This patch reverts previous "Avoid creating P2P prefetch
window for expansion ROMs" change due to regressions that
were spotted on some systems.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
tipar: remove obsolete module
The tipar character driver was used to implement bit-banging access
to Texas Instruments parallel link cable. A user-land method now
exists thru PPDEV & PARPORT.
Signed-off-by: Romain Liévin <roms@lpg.ticalc.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] add Nano 7240 driver
[WATCHDOG] ipmi: add the standard watchdog timeout ioctls
[WATCHDOG] IT8212F watchdog driver
[WATCHDOG] Sbus: cpwatchdog, remove SPIN_LOCK_UNLOCKED
[WATCHDOG] bfin_wdt, remove SPIN_LOCK_UNLOCKED
[WATCHDOG] Stop looking for device as soon as one is found
[WATCHDOG] at32ap700x_wdt: add support for boot status and add fix for silicon errata
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Fix lock flag variable location, bump version number
IB/ehca: Serialize HCA-related hCalls if necessary
IB/ehca: Return correct number of SGEs for SRQ
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
[IRDA]: irda parameters warning fixes.
[IRDA]: stir4200 fixes.
[IRDA]: irlmp_unregister_link() needs to free lsaps.
[IRDA]: mcs7780 needs to free allocated rx buffer.
[IRDA]: Race between open and disconnect in irda-usb.
[SCTP]: Flush fragment queue when exiting partial delivery.
[AX25]: Locking dependencies fix in ax25_disconnect().
[IPV4]: Make tcp_input_metrics() get minimum RTO via tcp_rto_min()
[IPV6]: Fix the return value of ipv6_getsockopt
[BRIDGE]: Assign random address.
[IPV4]: Updates to nfsroot documentation
[ATM]: Fix compiler warning noise with FORE200E driver
[NETFILTER]: bridge: fix missing link layer headers on outgoing routed packets
[SYNCPPP]: Endianness and 64bit fixes.
[TIPC]: Fix semaphore handling.
[NETFILTER]: xt_hashlimit should use time_after_eq()
[XFRM]: Display the audited SPI value in host byte order.
[NETFILTER]: ip_tables: fix compat copy race
[NETFILTER]: ctnetlink: set expected bit for related conntracks
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Make PS3_SYS_MANAGER default y, not m
[POWERPC] Fix rounding bug in emulation for double float operating
[POWERPC] iSeries: don't printk with HV spinlock held
[POWERPC] 82xx: mpc8272ads, pq2fads: Update defconfig with CONFIG_FS_ENET_MDIO_FCC
[POWRPC] CPM2: Eliminate section mismatch warning in cpm2_reset().
[POWERPC] Kill non-existent symbols from ksyms and commproc.h
[POWERPC] Fix typo #ifdef -> #ifndef
From: Olaf Hartmann <olaf.hartmann@s1998.tu-chemnitz.de>
The attached patch observes the stir4200 fifo size and will clear the
fifo, if the size is increasing, while it should be transmitting bytes
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing the mcs7780 based IrDA USB dongle I've stumbled upon
memory leak in mcs_net_close(). Patch below fixes it.
Signed-off-by: Hinko Kocevar <hinko.kocevar@cetrtapot.si>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems to me that irda_usb_net_open() must set self->netopen
under spinlock or disconnect() may fail to kill all URBs, if it is called
while an interface is opened.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc throws these warnings with:
CONFIG_ATM_FORE200E=m
# CONFIG_ATM_FORE200E_PCA is not set
drivers/atm/fore200e.c:2695: warning: 'fore200e_pca_detect' defined but
not used
drivers/atm/fore200e.c:2748: warning: 'fore200e_pca_remove_one' defined
but not used
By moving the #ifdef CONFIG_ATM_FORE200E_PCA around those two functions,
the compiler warnings are silenced.
Signed-off-by: Tom "spot" Callaway <tcallawa@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* trivial annotations
* long != 32bit, use __be32
* wrong endianness in sending CISCO_ADDR_REPLY
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently a device reset (ethtool -r ethX) would cause the
adapter to fall back to regular MTU sizes.
Signed-off-by: Matheos Worku <matheos.worku@sun.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
SPIN_LOCK_UNLOCKED is deprecated, use DEFINE_SPINLOCK instead
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Trivial fix to shut up gcc.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The zombie whitespace from outer space that will not die!
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Emil Medve <Emilian.Medve@Freescale.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Code used by the non-__devinit s2io_open() mustn't be __devinit.
This patch fixes the following section mismatch with CONFIG_HOTPLUG=n:
<-- snip -->
...
WARNING: vmlinux.o(.text+0x6f6e3e): Section mismatch: reference to .init.text.20:s2io_test_intr (between 's2io_open' and 's2io_ethtool_sset')
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes the following section mismatch with CONFIG_HOTPLUG=n:
<-- snip -->
...
WARNING: vmlinux.o(.init.text.20+0x4cb25): Section mismatch: reference to .exit.text:sis190_mii_remove (between 'sis190_init_one' and 'read_eeprom')
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
badly broken on big-endian
* passing little-endian to pci_unmap_single() et.al.
* cpu_to_le32() before passing value to writel()
* worse, cpu_to_le64() and shifting/masking result before the same
* hmp->tx_ring[i].status_n_length = cpu_to_le32(
DescEndRing |
(hmp->tx_ring[i].status_n_length & 0x0000FFFF));
is obviously bogus on big-endian. Not hard to untangle, fortunately...
* poisoning addresses in rx_ring is better done after we'd done
pci_unmap_single() on them, not before that. [this one affects little-endian
as well, obviously, provided that pci_unmap_single() is not a no-op on target
in question]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Adapted from Ian Wienand <ianw@gelato.unsw.edu.au>
Explicitly free the IRQ before removing the device to remove a
warning "Destroying IRQ without calling free_irq"
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Ian Wienand <ianw@gelato.unsw.edu.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Recognized VLAN ids are set via writew(), should go in host-endian.
That's a long-standing bug, BTW - see http://lkml.org/lkml/2004/2/27/180
for example. What happens is that card gets VLAN id table populated by
byteswapped values on little-endian boxen (so 257 works as expected, 256
and 258 do not, etc.). Bug is easily reproduced, patch fixes it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* all places where we assign ->addr get cpu_to_le32(pci_map_single(....)), so
we ought to convert back to host-endian before doing pci_unmap_single() et.al.
* poisoning addresses in netdev_close() should be done _after_ unmapping them,
not before it...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I'm using a Marvell 88E8062 on a custom PPC64 blade and ran into RX
lockups while validating the sky2 driver. The receive MAC FIFO would
become stuck during testing with high traffic. One port of the 88E8062
would lockup, while the other port remained functional. Re-inserting
the sky2 module would not fix the problem - only a power cycle would.
I looked over Marvell's most recent sk98lin driver and it looks like
they had a "workaround" for the Yukon XL that the sky2 doesn't have yet.
The sk98lin driver disables the RX MAC FIFO flush feature for all
revisions of the Yukon XL.
According to skgeinit.c of the sk98lin driver, "Flushing must be enabled
(needed for ASF see dev. #4.29), but the flushing mask should be
disabled (see dev. #4.115)". Nice. I implemented this same change in
the sky2 driver and verified that the RX lockup I was seeing was
resolved.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
klaptopd assumes rate to be in same units as capacity.
http://bugzilla.kernel.org/show_bug.cgi?id=9362
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Alarm bit should be cleared in order for other alarms to be sent.
http://bugzilla.kernel.org/show_bug.cgi?id=9362
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Updates the ucc_geth device driver to check the new rx-clock-name and
tx-clock-name properties first. If present, it uses the new function
qe_clock_source() to obtain the clock source. Otherwise, it checks the
deprecated rx-clock and tx-clock properties.
Update the device trees for 832x, 836x, and 8568 to contain the new property
names only.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch moves the CPM command handling into commproc.c
for CPM1 and cpm2_common.c. This is yet another preparation
to get rid of drivers accessing the CPM via the global cpmp.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
fpi->cp_command should be overwritten only if CONFIG_PPC_CPM_NEW_BINDING
is NOT set. Otherwise it is already set from the device tree.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Starting in 2.6.23...
Several reports from X60 users complained that the default Lenovo keymap
issuing EV_KEY KEY_BRIGHTNESS_UP/DOWN input events caused major issues when
the proper brightness support through ACPI video.c was loaded.
Therefore, remove the generation of these events by default, which is the
right thing for T60, X60, R60, T61, X61 and R61 with their latest BIOSes.
Distros that want to misuse these events into OSD reporting (which requires
an ugly hack from hell in HAL) are welcome to set up the key map they need
through HAL. That way, we don't break everyone else's systems.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
for sn2_defconfig:
WARNING: vmlinux.o(.text+0x4b8601): Section mismatch: reference to .init.data:node_to_pxm_map (between '__acpi_map_pxm_to_node' and 'acpi_get_pxm')
WARNING: vmlinux.o(.text+0x4b8741): Section mismatch: reference to .init.data:pxm_to_node_map (between 'acpi_map_pxm_to_node' and 'acpi_get_node')
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The ->cap fields of struct acpi_video_device and struct acpi_video_bus
are 1B each, not 4B. The oversized memset()'s corrupted the subsequent
list_head fields. This resulted in silent corruption without
CONFIG_DEBUG_LIST and BUG's with it. This patch uses sizeof() to pass
the proper bounds to the memset() calls and thereby correct the bugs.
Signed-off-by: William Irwin <wli@holomorphy.com>
Acked-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Len Brown <len.brown@intel.com>
QAM SNR values were incorrect when the cable was disconnected. This
patch extends the lookup tables to ensure correct values are being
returned.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since not all code under drivers/media/video/ depends on
CONFIG_VIDEO_DEV we cannot only enter it depending
on CONFIG_VIDEO_DEV.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Hermann Pitton for noticing that this was missing.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After commit 19fb145799 the callers in
videobuf-core.c that already hold the lock must call
__videobuf_read_start() instead of videobuf_read_start().
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
set_io_32bit() (ide_procset_t function) can race against running
PIO transfers. Fix it by using ide_spin_wait_hwgroup().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
After looking into the HPT370 manual (now that I have it) and re-checking all
the timing tables, here's what I have discovered:
- at 33 MHz clock, PIO mode 0 timings turned to be overclocked, and all other
PIO modes underclocked;
- at 50 MHz clock, PIO modes 0 to 2 turned to be overclocked;
- at 66 MHz clock, PIO mode 0 was overclocked too.
Finally, the taskfile timing (matching PIO mode 0) turned to be overclocked at
all clock frequencies (and in all manuals)...
The new timings have been tested on HPT370 chip (at 33 MHz PCI clock) and on
HPT371N chip (at both 50 and 66 MHz DPLL clock).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In case of Promise TX4 the first PCI device is located at slot 1
and the second one is at slot 2 so the offset used by pci_get_slot()
should be "+1" and not "+2".
Thanks goes out to Markus Dietz for bugreport and testing this patch.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
post_transform_command() call in cdrom_newpc_intr() has no effect because
it is done after the request has already been fully completed (rq->bio and
rq->data are always NULL). It was verified to be true regardless whether
INQUIRY command is using DMA or PIO to transfer data (by using modified
Tejun Heo's test-shortsg.c utility and adding a few printk()-s to ide-cd).
This was uncovered thanks to the "blk_end_request: full I/O completion
handler (take 3)" patch series from Kiyoshi Ueda.
Cc: jens.axboe@oracle.com
Cc: bharrosh@panasas.com
Cc: Kiyoshi Ueda <k-ueda@ct.jp.nec.com
Cc: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Tejun Heo <htejun@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide_xfer_verbose() fixups:
- beautify returned mode names
- fix PIO5 reporting
- make it return 'const char *'
* Change printk() level from KERN_DEBUG to KERN_INFO in ide_find_dma_mode().
* Add ide_id_dma_bug() helper based on ide_dma_verbose() to check for invalid
DMA info in identify block.
* Use ide_id_dma_bug() in ide_tune_dma() and ide_driveid_update().
As a result DMA won't be tuned or will be disabled after tuning if device
reports inconsistent info about enabled DMA mode (ide_dma_verbose() does the
same checks while the IDE device is probed by ide-{cd,disk} device driver).
* Remove no longer needed ide_dma_verbose().
This patch should fix the following problem with out-of-sync IDE messages
reported by Nick Warne:
hdd: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache<7>hdd:
skipping word 93 validity check
, UDMA(66)
and later debugged by Mark Lord to be caused by:
ide_dma_verbose()
printk( ... "2048kB Cache");
eighty_ninty_three()
printk(KERN_DEBUG "%s: skipping word 93 validity check\n");
ide_dma_verbose()
printk(", UDMA(66)"
Please note that as a result ide-{cd,disk} device drivers won't report the
DMA speed used but this is intended since now DMA mode being used is always
reported by IDE core code.
v2:
* fixes suggested by Randy:
- use KERN_CONT for printk()-s in ide-{cd,disk}.c
- don't remove argument name from ide_xfer_verbose() declaration
v3:
* Remove incorrect check for (id->field_valid & 1) from ide_id_dma_bug()
(spotted by Sergei).
* "XFER SLOW" -> "PIO SLOW" in ide_xfer_verbose() (suggested by Sergei).
* Fix ide_find_dma_mode() to report the correct mode ('mode' after being
limited by 'req_mode').
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Nick Warne <nick@ukfsn.org>
Cc: Mark Lord <lkml@rtr.ca>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* remove trailing whitespaces
* 'if()' -> 'if ()'
* remove extra new-line before EXPORT_SYMBOL_GPL()
* add extra new-line after 'id' definition
* respect 80-columns limit
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add missing checks for control register existence (some legacy m68k specific
IDE controllers don't have it). Also use drive->ctl while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Several pSeries firmware versions share a rare locking issue in the
HCA-related hCalls. Check for a feature flag that indicates the issue
being fixed and serialize all HCA hCalls if not.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Firmware would round up the number of SGEs to four, because the WQE
structure holds four SGEs. For SRQ, only three are supported, so return
a fixed value instead.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The JMicron JMB38x chip doesn't support transfers that aren't 32-bit
aligned (both size and start address). It also doesn't like switching
between PIO and DMA mode, so it needs to be reset after each request.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some controllers have been designed on the assumption that all transfers
will be 32-bit aligned, both in start address and in size. This is not a
guarantee the SDHCI specification provides and not one we can provide.
Revert back to PIO for individual requests in order to work around the
hardware bug.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch against 2.6.23 sparc-2.6.git contains a number of minor
cleanups of the sparc serial drivers. Initially I fixed this build
warning:
WARNING: vmlinux.o(.text+0x107a2c): Section mismatch: reference to .init.text:add_preferred_console (between 'sunserial_console_match' and 'sunserial_console_termios')
which is done by declaring sunserial_console_match() as __init. This
resulted in build warnings on sunserial_current_minor. To resolve
these the variable was changed so it is no longer global, and to hide
operations on it inside 2 new functions. These functions handle the
UART minor handling code that is common to all sparc serial drivers.
These changes allowed to clean up the uart counters in all the sparc
serial drivers, and the administration of minor device numbers.
Lastly, sunserial_console_termios() does not need to be exported since
it is only called from non-modular code.
Sadly, the following build warning still exists:
WARNING: vmlinux.o(__ksymtab+0x2910): Section mismatch: reference to .init.text:sunserial_console_match (between '__ksymtab_sunserial_console_match' and '__ksymtab_sunserial_unregister_minors')
This could be resolved by not exporting sunserial_console_match(), but
this is not possible at the moment because it is being called from
modular code. On the other hand, this is a bogus warning since it
comes from a ksymtab section.
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Build fix to the isp1301_omap driver ... this driver gets built
more often in the OMAP tree than in mainline, partly because the
defconfig for H2 (plus probably H3 and H4) needs updating.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is required to let hwmon drivers attach to the adapter.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
videobuf_dvb needs videobuf_read_start. The EXPORT_SYMBOL_GPL() were removed by
a previous patch. However, videobuf_dvb needs this.
This patch re-adds videobuf_read_start, doing the proper lock.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This reverts commit 70eba18b56, as per
Jeff Garzik:
"That was meant for 2.6.25, and actually (due to patching) applied to
a completely unrelated 2.6.24 net driver."
Noted-by: Roland Dreier <rdreier@cisco.com>
Requested-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
