replace LHCALL_SET_PMD with LHCALL_SET_PGD hypercall name
(That's really what it is, and the confusion gets worse with PAE support)
Signed-off-by: Matias Zabaljauregui <zabaljauregui@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reported-by: Jeremy Fitzhardinge <jeremy@goop.org>
Some cleanups and replace direct assignment with native_set_* macros which properly handle 64-bit entries when PAE is activated
Signed-off-by: Matias Zabaljauregui <zabaljauregui@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
If GDT_ENTRIES were every > 256, this could become a problem.
Signed-off-by: Matias Zabaljauregui <zabaljauregui at gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
lguest never checked for pending interrupts when enabling interrupts, and
things still worked. However, it makes a significant difference to TCP
performance, so it's time we fixed it by introducing a pending_irq flag
and checking it on irq_restore and irq_enable.
These two routines are now too big to patch into the 8/10 bytes
patch space, so we drop that code.
Note: The high latency on interrupt delivery had a very curious
effect: once everything else was optimized, networking without GSO was
faster than networking with GSO, since more interrupts were sent and
hence a greater chance of one getting through to the Guest!
Note2: (Almost) Closing the same loophole for iret doesn't have any
measurable effect, so I'm leaving that patch for the moment.
Before:
1GB tcpblast Guest->Host: 30.7 seconds
1GB tcpblast Guest->Host (no GSO): 76.0 seconds
After:
1GB tcpblast Guest->Host: 6.8 seconds
1GB tcpblast Guest->Host (no GSO): 27.8 seconds
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
When the Guest does the LHCALL_HALT hypercall, we go to sleep, expecting
that a timer or the Waker will wake_up_process() us.
But we do it in a stupid way, leaving a classic missing wakeup race.
So split maybe_do_interrupt() into interrupt_pending() and
try_deliver_interrupt(), and check maybe_do_interrupt() and the
"break_out" flag before calling schedule.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The Launcher could be inside the Guest on another CPU; wake_up_process
will do nothing because it is "running". kick_process will knock it
back into our kernel in this case, otherwise we'll miss it until the
next guest exit.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This patch allows a virtio driver to use VIRTIO_DEV_ANY_ID for the
device id. This will be used by a test module that can be bound to
any virtio device.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This bug never appeared, since all current virtio drivers use
VIRTIO_DEV_ANY_ID for the vendor field. If a real vendor would be used,
the check in virtio_id_match is wrong - it returns 0 if
id->vendor == dev->id.vendor.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
If the device fills less than 4 bytes of our random buffer, we'll
BUG_ON. It's nicer to handle the case where it partially fills the
buffer (the protocol doesn't explicitly bad that).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The remove member of the virtio_driver structure uses __devexit_p(), so
the remove function itself should be marked with __devexit. And where
there be __devexit on the remove, so is there __devinit on the probe.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Add a new feature flag for indirect ring entries. These are ring
entries which point to a table of buffer descriptors.
The idea here is to increase the ring capacity by allowing a larger
effective ring size whereby the ring size dictates the number of
requests that may be outstanding, rather than the size of those
requests.
This should be most effective in the case of block I/O where we can
potentially benefit by concurrently dispatching a large number of
large requests. Even in the simple case of single segment block
requests, this results in a threefold increase in ring capacity.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This implements optional MSI-X support in virtio_pci.
MSI-X is used whenever the host supports at least 2 MSI-X
vectors: 1 for configuration changes and 1 for virtqueues.
Per-virtqueue vectors are allocated if enough vectors
available.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (+ whitespace, style)
This reorganizes virtio-pci code in vp_interrupt slightly, so that
it's easier to add per-vq MSI support on top.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This replaces find_vq/del_vq with find_vqs/del_vqs virtio operations,
and updates all drivers. This is needed for MSI support, because MSI
needs to know the total number of vectors upfront.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (+ lguest/9p compile fixes)
Add a linked list of all virtqueues for a virtio device: this helps for
debugging and is also needed for upcoming interface change.
Also, add a "name" field for clearer debug messages.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Virtio devices are supposed to negotiate features before they start using
the device, but the current code doesn't do this. This is because the
driver's probe() function invariably has to add buffers to a virtqueue,
or probe the disk (virtio_blk).
This currently doesn't matter since no existing backend is strict about
the feature negotiation. But it's possible to imagine a future feature
which completely changes how a device operates: in this case, we'd need
to acknowledge it before using the device.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
1) Now module_param(..., invbool, ...) requires a bool, and similarly
module_param(..., bool, ...) allows it, change pmi_setpal to a bool.
2) #define param_get_scroll to NULL, since it can never be called (perm
argument to module_param_named is 0).
3) Return -EINVAL from param_set_scroll if the value is bad, so it's
reported.
Note that I don't think the old fb_get_options() is required for new
drivers: the parameters automatically work as uvesafb.XXX=... anyway.
Acked-by: Michał Januszewski <spock@gentoo.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
It takes an 'int' for historical reasons, and there are only two
users: simply switch it over to bool.
The other user (uvesafb.c) will get a (harmless-on-x86) warning until
the next patch is applied.
Cc: Brad Douglas <brad@neruo.com>
Cc: Michal Januszewski <spock@gentoo.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Russell explains the __module_get():
> cyber2000fb.c does it in its module initialization function
> to prevent the module (when built for Shark) from being unloaded. It
> does this because it's from the days of 2.2 kernels and no one bothered
> writing the module unload support for Shark.
Since 2.4, the correct answer has been to not define an unload fn.
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Cc: alex@shark-linux.de
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This file is no longer annotated for false positives but the kmemleak.h
include was still present.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Alan Cox <alan.cox@linux.intel.com>
Function graph tracer support for s390.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a DASD requests is started with dasd_sleep_on and fails, then the
calling function may need to know the reason for the failure.
In cases of hardware errors it can inspect the sense data in the irb,
but when the reason is internal (e.g. start_IO failed) then it needs
a meaningfull return code.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Some functions called as a late_initcall depend on completely
initialized devices. Since commit
f3445a1a65 the dasd driver uses the
new async framework and relies on the fact that synchronization is
done in prepare_namespace which is called after the late_initcalls.
Fix this by calling async_synchronize_full at the end of the related
init functions.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix a broken memset (sizeof pointer vs sizeof the underlying
structure) by cleaning up the involved functions.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The High Performance FICON feature is not supported in 31-bit mode,
no matter what the various flags say. So we need to check for the
CONFIG_64BIT option as well.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
git commit f331c0296f changed users of
->first_minor to devt. This broke device handling in dcssblk, so that
no additional devices could be added after the first one.
This patch reverts the devt conversion to the previous ->first_minor
handling.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Do not go beyond ARRAY_SIZE of irq_ptr->{in,out}put_qs
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Lockdep found a problem with the lock order of the view lock and the
ccw device lock. raw3270_activate_view/raw3270_deactivate_view first
take the ccw device lock then call the activate/deactivate functions
of the view which take view lock. The update functions of the
con3270/tty3270 view will first take the view lock, then take the
ccw device lock. To fix this the activate/deactivate functions are
changed to avoid taking the view lock by moving the functions calls
that modify the 3270 output buffer to the update function which is
called by a timer.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The tty3270_notifier that calls tty_register_device / tty_unregister_device
is harmful in two ways:
1) the device node that is create is wrong because the minor numbers for
3270 tty start with 1 and tty_notifier passes the minor as index.
2) If 1) is corrected you'll get a warning:
WARNING: at fs/sysfs/dir.c:462 sysfs_add_one+0x4c/0x60()
sysfs: duplicate filename '227:1' can not be created
The 227:1 link is already created by raw3270_create_attributes to refer
to ../../class/tty/tty<devno>. There cannot be two links.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move qdio_perf_stat_inc to the header file so it can be inlined.
Remove unused qdio_perf_stat_dec.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The check for the device status in qdio_establish_handle_irq()
had dead code. Remove the unused code and simplify the error
handling.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Some sanity checks in device_ops.c test the output of container_of
macros to be !NULL. Test the input parameters instead.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
All definition in cpu.h have to do with cputime accounting. Move
them to cputime.h and remove the header file.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
add exports so TTM module can use these functions.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
this is a TTM preparation patch, it rearranges the mm and
add operations needed to do mm operations in atomic context.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This code depends on the underlying I2C adapter using the bit-banging algo,
which may not be the case. If specific encoders require this mechanism, they
should build a custom I2C algo that implements this workaround, rather than
having it in the general path.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
vfree() does it's own NULL checking, no need for explicit check before
calling it.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Replace the DRM_DEBUG with the DRM_DEBUG_DRIVER to print the debug info
in i915 driver.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Replace the DRM_DEBUG with DRM_DEBUG_MODE macro to print the info in drm_mode.
airlied:- fixed up to remove a conflicting #define
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The only user of the i_cindex element in the inode structure is used
is by the firewire drivers. As part of an attempt to slim down the
inode structure to save memory --- since a typical Linux system will
have hundreds of thousands if not millions of inodes cached, a
reduction in the size inode has high leverage.
The firewire driver does not need i_cindex in any fast path, so it's
simple enough to calculate when it is needed, instead of wasting space
in the inode structure.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: krh@redhat.com
Cc: stefanr@s5r6.in-berlin.de
Cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'for-linus' of git://linux-arm.org/linux-2.6:
kmemleak: Add the corresponding MAINTAINERS entry
kmemleak: Simple testing module for kmemleak
kmemleak: Enable the building of the memory leak detector
kmemleak: Remove some of the kmemleak false positives
kmemleak: Add modules support
kmemleak: Add kmemleak_alloc callback from alloc_large_system_hash
kmemleak: Add the vmalloc memory allocation/freeing hooks
kmemleak: Add the slub memory allocation/freeing hooks
kmemleak: Add the slob memory allocation/freeing hooks
kmemleak: Add the slab memory allocation/freeing hooks
kmemleak: Add documentation on the memory leak detector
kmemleak: Add the base support
Manual conflict resolution (with the slab/earlyboot changes) in:
drivers/char/vt.c
init/main.c
mm/slab.c
* 'perfcounters-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (574 commits)
perf_counter: Turn off by default
perf_counter: Add counter->id to the throttle event
perf_counter: Better align code
perf_counter: Rename L2 to LL cache
perf_counter: Standardize event names
perf_counter: Rename enums
perf_counter tools: Clean up u64 usage
perf_counter: Rename perf_counter_limit sysctl
perf_counter: More paranoia settings
perf_counter: powerpc: Implement generalized cache events for POWER processors
perf_counters: powerpc: Add support for POWER7 processors
perf_counter: Accurate period data
perf_counter: Introduce struct for sample data
perf_counter tools: Normalize data using per sample period data
perf_counter: Annotate exit ctx recursion
perf_counter tools: Propagate signals properly
perf_counter tools: Small frequency related fixes
perf_counter: More aggressive frequency adjustment
perf_counter/x86: Fix the model number of Intel Core2 processors
perf_counter, x86: Correct some event and umask values for Intel processors
...
* 'topic/slab/earlyboot' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
vgacon: use slab allocator instead of the bootmem allocator
irq: use kcalloc() instead of the bootmem allocator
sched: use slab in cpupri_init()
sched: use alloc_cpumask_var() instead of alloc_bootmem_cpumask_var()
memcg: don't use bootmem allocator in setup code
irq/cpumask: make memoryless node zero happy
x86: remove some alloc_bootmem_cpumask_var calling
vt: use kzalloc() instead of the bootmem allocator
sched: use kzalloc() instead of the bootmem allocator
init: introduce mm_init()
vmalloc: use kzalloc() instead of alloc_bootmem()
slab: setup allocators earlier in the boot sequence
bootmem: fix slab fallback on numa
bootmem: use slab if bootmem is no longer available
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] ata_piix: Enable parallel scan
sata_nv: use hardreset only for post-boot probing
[libata] ahci: Restore SB600 SATA controller 64 bit DMA
ata_piix: Remove stale comment
ata_piix: Turn on hotplugging support for older chips
ahci: misc cleanups for EM stuff
[libata] get rid of ATA_MAX_QUEUE loop in ata_qc_complete_multiple() v2
sata_sil: enable 32-bit PIO
sata_sx4: speed up ECC initialization
libata-sff: avoid byte swapping in ata_sff_data_xfer()
[libata] ahci: use less error-prone array initializers
* 'for-2.6.31' of git://git.kernel.dk/linux-2.6-block: (153 commits)
block: add request clone interface (v2)
floppy: fix hibernation
ramdisk: remove long-deprecated "ramdisk=" boot-time parameter
fs/bio.c: add missing __user annotation
block: prevent possible io_context->refcount overflow
Add serial number support for virtio_blk, V4a
block: Add missing bounce_pfn stacking and fix comments
Revert "block: Fix bounce limit setting in DM"
cciss: decode unit attention in SCSI error handling code
cciss: Remove no longer needed sendcmd reject processing code
cciss: change SCSI error handling routines to work with interrupts enabled.
cciss: separate error processing and command retrying code in sendcmd_withirq_core()
cciss: factor out fix target status processing code from sendcmd functions
cciss: simplify interface of sendcmd() and sendcmd_withirq()
cciss: factor out core of sendcmd_withirq() for use by SCSI error handling code
cciss: Use schedule_timeout_uninterruptible in SCSI error handling code
block: needs to set the residual length of a bidi request
Revert "block: implement blkdev_readpages"
block: Fix bounce limit setting in DM
Removed reference to non-existing file Documentation/PCI/PCI-DMA-mapping.txt
...
Manually fix conflicts with tracing updates in:
block/blk-sysfs.c
drivers/ide/ide-atapi.c
drivers/ide/ide-cd.c
drivers/ide/ide-floppy.c
drivers/ide/ide-tape.c
include/trace/events/block.h
kernel/trace/blktrace.c
* 'for-2.6.31' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (28 commits)
ide-tape: fix debug call
alim15x3: Remove historical hacks, re-enable init_hwif for PowerPC
ide-dma: don't reset request fields on dma_timeout_retry()
ide: drop rq->data handling from ide_map_sg()
ide-atapi: kill unused fields and callbacks
ide-tape: simplify read/write functions
ide-tape: use byte size instead of sectors on rw issue functions
ide-tape: unify r/w init paths
ide-tape: kill idetape_bh
ide-tape: use standard data transfer mechanism
ide-tape: use single continuous buffer
ide-atapi,tape,floppy: allow ->pc_callback() to change rq->data_len
ide-tape,floppy: fix failed command completion after request sense
ide-pm: don't abuse rq->data
ide-cd,atapi: use bio for internal commands
ide-atapi: convert ide-{floppy,tape} to using preallocated sense buffer
ide-cd: convert to using generic sense request
ide: add helpers for preparing sense requests
ide-cd: don't abuse rq->buffer
ide-atapi: don't abuse rq->buffer
...
Slab is initialized before the console subsystem so use the slab allocator in
vgacon_scrollback_startup().
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Now that kmem_cache_init() happens before console_init(), we should use
kzalloc() and not the bootmem allocator.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
There are allocations for which the main pointer cannot be found but
they are not memory leaks. This patch fixes some of them. For more
information on false positives, see Documentation/kmemleak.txt.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
* serial-from-alan: (79 commits)
moxa: prevent opening unavailable ports
imx: serial: use tty_encode_baud_rate to set true rate
imx: serial: add IrDA support to serial driver
imx: serial: use rational library function
lib: isolate rational fractions helper function
imx: serial: handle initialisation failure correctly
imx: serial: be sure to stop xmit upon shutdown
imx: serial: notify higher layers in case xmit IRQ was not called
imx: serial: fix one bit field type
imx: serial: fix whitespaces (no changes in functionality)
tty: use prepare/finish_wait
tty: remove sleep_on
sierra: driver interface blacklisting
sierra: driver urb handling improvements
tty: resolve some sierra breakage
timbuart: Fix the termios logic
serial: Added Timberdale UART driver
tty: Add URL for ttydev queue
devpts: unregister the file system on error
tty: Untangle termios and mm mutex dependencies
...
In moxa.c there are 32 minor numbers reserved for each device. The
number of ports actually available per device is stored in
moxa_board_conf->numPorts. This number is not considered in moxa_open().
Opening a port that is not available results in a kernel oops.
This patch adds a test to moxa_open() that prevents opening unavailable
ports.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
real baud rate may be different from the one requested.
for upper layers, set the nearest value to the real rate
in favour of the rate previously requested.
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using the iMX serial driver with an IrDA device
needs extra peripheral settings and specific
timing depending on the transmitter circuitry used.
Signed-off-by: Fabian Godehardt <fg@emlix.com>
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
for calculation of numerator and denominator
used in baud rate setting, use generic library function
for optimum settings.
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
correctly de-initialise device when setting up failed,
call to pdata->exit() was missing.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
needed to avoid continued transmission by hardware
while software already shuts down, which might
cause dangling characters to show up in hardware
queues when restarting the device.
Signed-off-by: Fabian Godehardt <fg@emlix.com>
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
upper layers, namely line discipline, need to be notified
when transmission of more data is possible. For spurious
cases, where IRQ handling does not supply notification
for sure, it is given additionally here, when data has just
been transmitted and space in the buffer will most probably
be available.
Signed-off-by: Fabian Godehardt <fg@emlix.com>
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"have_rtscts" is assigned 1, while it is declared
int:1, two's complement, which can hold 0 and -1
only. The code works, as the upper bits are cut
off, and tests are done against 0 only.
Nonetheless, correctly declaring the bit field
as unsigned int:1 renders the code more robust.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use prepare_to_wait and finish_wait instead of add_wait_queue and
remove_wait_queue.
This avoids us setting a task state.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use wait_event instead of sleep_on in tty_block_til_ready.
Wait for ASYNC_CLOSING flag being 0.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Interface blacklisting is necessary for non-serial interfaces that are handled
by a different driver. The interface blacklisting is implemented in sierra
driver per device. Each device in need of a blacklist has a static information
array kept in the driver. This array contains the interface numbers that are
blacklisted. The pointer for each blacklist array and the length
of that blacklist are 'bundled' in data structure sierra_iface_info. A pointer
to this information is set in id_table when the device is added to the id_table.
The following is summary of changes we have made to sierra.c driver in
this patch dealing with interface blacklisting support:
- Added data structure sierra_iface_info and function is_blacklisted()
to support blacklisting
- Modified sierra_probe() to handle blacklisted interfaces accordingly
- Improved comments in id_table
- Added new device in id_table with blacklist interface support
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[Folded from eight patches into one as the original set according to the
author "All of the patches need to be applied to obtain a working product"
so keeping them split seems unhelpful
Merge fixes done versus other conflicting changes and moved the
spin_lock_init from open to setup time -- Alan]
Summary of the changes and code re-organization in this patch:
- The memory for urbs is allocated and urbs are submitted only for the active
interfaces (instead of pre-allocating these for all interfaces). This will
save memory especially in the case of using composite devices.
- The code has been re-organized and functionality has been extracted from
sierra_startup(), sierra_shutdown(), sierra_open(), sierra_close() and added
in helper functions sierra_release_urb(), sierra_stop_rx_urbs(),
sierra_submit_rx_urbs() and sierra_setup_urb()
- Added function sierra_release_urb() to free an urb and its transfer
buffer.
- Removed unecessary include file reference and comment.
- Added function sierra_stop_rx_urbs() that takes care of the release of
receive and interrupt urbs. This function is to be called by sierra_close()
whenever an interface is de-activated.
- Added new function sierra_submit_rx_urbs() that handles the submission of
receive urbs and interrupt urbs (if any) during the interface activation.
This function is to be called by sierra_open(). Added a second parameter to
pass the memory allocation (as suggested by Oliver Neukum) so that this
function can be used in post_reset() and resume().
- Added new function sierra_setup_urb() that contains the functionality to
allocate an urb, fill bulk urb using the supplied memory allocation flag
and release urb upon error. Added parameter so that the caller pass the
memory allocation flag for flexibility.
- Moved sierra_close() before sierra_open() to resolve dependencies
introduced by the code reorganization.
- Modified sierra_close() to call sierra_stop_rx_urbs() and
sierra_release_urb() functions added in previous patch.
- Modified sierra_open() to call sierra_setup_urb() and sierra_submit_rx_urbs()
functions; note urbs are allocated and submitted for each activated interface.
- Modified sierra_startup() so that allocation of urbs happens whenever an
interface is activated (urb allocation is moved to sierra_open()).
- Modified sierra_shutdown() so that urbs are freed whenever an interface is
de-activated (urb freeing moved to sierra_close() as shown in previous patch
from the series)
- Removed unecessary data structure from sierra_port_private_data
- Suppress an entry in logs by not re-submitting an urb when usb_submit_urb()
returns -EPERM, as this shows that usb_kill_urb() is running (as suggested by
Oliver Neukum)
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Alan Cox <alan.cox@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The various merges into the sierra driver inadvertently undid
commit 212b8f0c3f by Elina Pasheva
<epasheva@sierrawireless.com>. Put it back so the OBEX port works again.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver only handles speeds but it fails to return the current values
for the hardware features it does not support.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Driver for the UART found in the Timberdale FPGA
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Although this doesn't cause any problems it could potentially do so for
future mmap using devices. No real work is needed to sort it out so untangle
it before it causes problems
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Blackfin JTAG interface has a 4 byte generic data field (EMUDAT). With
a little creative thinking, we can turn this into a TTY device.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new open/close logic handles DTR and friends, so don't do it in our own
open routine as well.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bluetooth shouldn't be doing this as most drivers don't support the flag,
furthermore it shouldn't be needed with newer buffering. This becomes rather
more visible as the locking fixes make the abuse of low_latency visible as
spew on the users console/dmesg.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows users to use the standard setserial command with this FT232
feature as well as obscure chip specific interfaces we have now. We keep
track of and respect the sysfs value for non-low-latency cases. In theory we
could do smart stuff with VTIME and the like but this seems of questionable
worth.
Closes-bug: http://bugzilla.kernel.org/show_bug.cgi?id=9120
Signed-off-by: Alan Cox <alan@linux.intel.com)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces the string "CP2101" with "CP210x" within cp210x.c
This is to reduce confusion about the fact that the driver is actually
compatible with CP2101, CP2102 and CP2103 devices.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
(Fixed some collisions merging)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The CP210X driver was developed without official device specifications.
This has lead to an incorrect assumption that all GET request codes are
equal to the corresponding SET request code +1.
This patch removes this incorrect assumption, and uses request code
definitions based on the updated GPL driver from SiLabs.
This modification is needed before extended functionality such as GPIO
on CP2103 can be supported.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The UART RX handling code isn't exactly speeding, so don't go disabling
all interrupts when processing the buffer. Just disable the relevant DMA
interrupt. This greatly improves latency of the system when utilizing the
UART.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
05000231 - UART STB Bit Incorrectly Affects Receiver Setting
For processors affected by this, we cannot safely allow CSTOPB to be set
as the UART will then be unable to properly clock in bytes.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add some comments for how these anomalies are addressed:
05000215 - UART TX Interrupt Masked Erroneously
We always clear ETBEI within last UART TX interrupt to end
a string. It is always set when starting a new tx transfer.
05000099 - UART Line Status Register (UART_LSR) Bits Are Not Updated at
the Same Time
This anomaly affects driver only in POLL code where multi bits of
UART_LSR are checked. It doesn't affect current bfin_5xx.c driver.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This bug is caused by irregular behavior of DMA register CURR_X_COUNT
and CURR_Y_COUNT when an auto restart uart rx DMA run to last byte in
DMA buffer, trigger the interrupt and stay at this possiton. The status
of current x and y is 0:7 instead of 512:8 or 0:8. The driver doesn't
take care of this case when calculating the position.
URL: http://blackfin.uclinux.org/gf/tracker/5063
Reported-by: Tomasz Motylewski <t.motylewski@bfad.de>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a SSYNC() into bfin_serial_dma_tx_chars() to ensure DMA registers are
written with new data otherwise we might miss a byte or two when the
system is under load. PIO mode is OK though.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since we already setup the early console UART in
arch/blackfin/kernel/early_printk.c, and common functions which are
enabled from the .setup will override the proper settings later, don't
fill in these structures. Otherwise we get mangled baudrate settings when
using early_printk.
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ignore receiving data if new position is in the same line of current
buffer tail and is small. This should decrease overruns.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hopefuly the new version is easier to read, but in the process it declares
proper clobber lists and better constraints so that GCC can do a better
job at allocating free registers.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SPORT transmit frame sync (TFS) isn't used as an electrical signal during
normal SPORT UART emulation. However, it is useful in EIA RS-485
emulation as RS-485 Transceiver Driver Enable DE strobe.
This patch configures:
TFS to be active high in order to drive an DE strobe of
an eventually connected RS-485 Transceiver.
Late frame sync mode (LATFS) gating the entire TX shift cycle.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for the TI AR7 internal UART.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As it is, defining ICOM_TRACE produces some compile errors, as
"parameter name omitted" and "redefinition of ‘trace’"
This patch removes the wrong trace definition.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
And tidy up a few bits coding style detectors missed
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael's patch fixed some of the coding style so the style is now
inconsistent. Sort the rest out
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes array subscription bugs in the parport_pc driver.
drivers/parport/parport_pc.c: In function ‘parport_irq_probe’:
drivers/parport/parport_pc.c:1589: warning: array subscript is above array bounds
drivers/parport/parport_pc.c: In function ‘parport_pc_probe_port’:
drivers/parport/parport_pc.c:1579: warning: array subscript is above array bounds
The patch also fixes a few other array bugs, which the compiler was
unable to find. Coding style violations are also fixed.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Having cleaned up the allocators we might as well remove the inline helpers
for some of it
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Long long ago a 4K kmalloc allocated two pages so the tty layer used the
page allocator, except on some machines where the page size was huge. This was
removed from the core tty layer with the tty buffer re-implementation but not
from tty_audit or the n_tty ldisc.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
adapter->version can only be ADAPTER_V2 or ADAPTER_V1. So,
that OR operand in the "if" clause is non-sense and can be removed.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If there are more then one 4/8-port board jsm_uart_port_init
allocate a line numbers of the second and further boards
from range of previous one.
This patch fixed the problem.
Signed-off-by: Alexander Y. Fomichev <git.user@gmail.com>
[printks fixed to add jsm: ]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
set_termios can now be used for setting the parity and the stopbits. This is
needed to use with cards which use a different parity then the parity used at
start (even).
If the iuu_uart_baud function return an error, we will return the old_termios
instead of the new one.
Signed-off-by: Olivier Bornet <Olivier.Bornet@puck.ch>
This was then revamped to use the various helpers, not copy non-hardware
bits any to add mark/space parity and csize reporting
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bring in the relevant bits of the 0.9 vendor driver.
Signed-off-by: Olivier Bornet <Olivier.Bornet@puck.ch>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have a tty_ldisc file now so put tty_ldisc_flush in the right place
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are several pretty much unfixable races in the old ldisc code, especially
with respect to pty behaviour and also to hangup. It's easier to rewrite the
code than simply try and patch it up.
This patch
- splits the ldisc from the tty (so we will be able to refcount it more cleanly
later)
- introduces a mutex lock for ldisc changing on an active device
- fixes the complete mess that hangup caused
- implements hopefully correct setldisc/close/hangup locking
There are still some problems around pty pairs that have always been there but
at least it is now possible to understand the code and fix further problems.
This fixes the following known bugs
- hang up can leak ldisc references
- hang up may not call open/close on ldisc in a matched way
- pty/tty pairs can deadlock during an ldisc change
- reading the ldisc proc files can cause every ldisc to be loaded
and probably a few other of the mysterious ldisc race reports.
I'm sure it also adds the odd new one.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Before trying to tackle the ldisc bugs the code needs to be a good deal
more readable, so do the simple extractions of routines first.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Costantino Leandro found a bug in tty_find_polling_driver and provided a
patch that fixed the crash but not the underlying bug. This fixes the
underlying bug where the list walk corrupts the values it is using on a
match but then reuses them if the open fails.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We fixed the globals, so now fix the comment
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tty throttling code can race due to the lock drops. It takes very high
loads but this has been observed and verified by Rob Duncan.
The basic problem is that on an SMP box we can go
CPU #1 CPU #2
need to throttle ?
suppose we should buffer space cleared
are we throttled
yes ? - unthrottle
call throttle method
This changeet take the termios lock to protect against this. The termios
lock isn't the initial obvious candidate but many implementations of throttle
methods already need to poke around their own termios structures (and nobody
really locks them against a racing change of flow control).
This does mean that anyone who is setting tty->low_latency = 1 and then
calling tty_flip_buffer_push from their unthrottle method is going to end up
collapsing in a pile of locks. However we've removed all the known bogus
users of low_latency = 1 and such use isn't safe anyway for other reasons so
catching it would be an improvement.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for the following serial controller chip:
Oxford Semiconductor OXCB950 for PCI Cardbus interface
http://www.transdimension.com/products/serial/OXCB950.html
on this card:
ExSys EX-1370 1 port high-speed serial card for ExpressCard/34 slot
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch from ASYNC_* to ASYNCB_*, because test_bit expects
bit number, not mask.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch from ASYNC_* to ASYNCB_*, because {test,set}_bit expect
bit number, not mask.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Or at least most of it. There are further clean ups possible and there are
are also thing checkpatch moans about that would be silly to "fix".
Also note some FIXME points found as the cleanup was done.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now we have a port structure begin using the fields and kref counts
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Set up ports right after FW load so that we won't allocate maximal
(64) ports when we use few.
Also remove reading of nports in irq context, since we know it from
initialisation now.
This also fixes a tty ports unregistration on some fail paths and for
Ze which registered 64 and unregistered real port count.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove ugly macros and add inlines instead of them. This improves
readability and type checking a much.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Store HW version locally to not read it all the time in interrupts
and alike.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove ugly all-over-the-code casts of ctl_addr to 9060 space.
Add an union to the cyclades_card structure, which contains
a pointer to both 9050 and 9060 spaces.
The 9050 space layout is unknown, so let it still as a void
__iomem pointer.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add receive programmed IO mode to reduce receive latency
when using low data rates. The receive FIFO trigger
level of 128 bytes used in DMA mode creates excessive latency
when operating at low data rates. PIO mode is selected when user
application requests data in blocks of less than 128 bytes.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The CDC ACM driver uses the tty layer correctly so needs conversion. Start by
adding and initializing the port structures.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows us to clean stuff up, but is probably also going to cause
some app breakage with buggy apps as we now implement proper POSIX behaviour
for USB ports matching all the other ports. This does also mean other apps
that break on USB will now work properly.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need this for devices that cannot flush and wait, but which do not order
data and modem events. Without it we will hang up before all the data
clears the hardware. Needed for the USB changes.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some drivers implement this internally, others miss it out. Push the
behaviour into the core code as that way everyone will do it consistently.
Update the dtr rts method to raise or lower depending upon flags. Having a
single method in this style fits most of the implementations more cleanly than
two funtions.
We need this in place before we tackle the USB side
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No need to check if dev_id is NULL, it never is.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't reset the PLX chip after FW load, which effectively kills
the FW, so that user had to boot manually.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ze needs firmware to be loaded as well as Zo. Move cyz_load_fw one
level upper to achieve that.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I found the PrimeCell/AMBA Bus drivers distrusting the resource
passed in as part of the struct amba_device abstraction. This
patch removes all hard coded resource sizes found in the PrimeCell
drivers and move the responsibility of this definition back to
the platform/board device definition, which already exist and
appear to be correct for all in-tree users of these drivers.
We do this using the resource_size() inline function which was
also replicated in the only driver using the resource size, so
that has been changed too. The KMI_SIZE was left in kmi.h in case
someone likes it. Test-compiled against Versatile and Integrator
defconfigs, seems to work but I don't posess these boards and
cannot test them.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the DRM_DEBUG_KMS/DEBUG_LOG_KMS to print the debug info for
SDVO device.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use the DRM_DEBUG_KMS macro definition to print the debug info for
the LVDS.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now all the DRM debug info will be reported if the boot option of
"drm.debug=1" is added. Sometimes it is inconvenient to get the debug
info in KMS mode. We will get too much unrelated info.
This will separate several DRM debug levels and the debug level can be used
to print the different debug info. And the debug level is controlled by the
module parameter of drm.debug
In this patch it is divided into four debug levels;
drm_core, drm_driver, drm_kms, drm_mode.
At the same time we can get the different debug info by changing the debug
level. This can be done by adding the module parameter. Of course it can
be changed through the /sys/module/drm/parameters/debug after the system is
booted.
Four debug macro definitions are provided.
DRM_DEBUG(fmt, args...)
DRM_DEBUG_DRIVER(prefix, fmt, args...)
DRM_DEBUG_KMS(prefix, fmt, args...)
DRM_DEBUG_MODE(prefix, fmt, args...)
When the boot option of "drm.debug=4" is added, it will print the debug info
using DRM_DEBUG_KMS macro definition.
When the boot option of "drm.debug=6" is added, it will print the debug info
using DRM_DEBUG_KMS/DRM_DEBUG_DRIVER.
Sometimes we expect to print the value of an array.
For example: SDVO command,
In such case the following four DRM debug macro definitions are added:
DRM_LOG(fmt, args...)
DRM_LOG_DRIVER(fmt, args...)
DRM_LOG_KMS(fmt, args...)
DRM_LOG_MODE(fmt, args...)
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now that the dependent patches are merged, we are ready to enable
sparseirq support. This simply adds the Kconfig option, and then converts
from the _cpu to the _node allocation routines to follow the upstream
sparseirq API changes.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
A driver will use the _DRM_DRIVER map flag to indicate that it wants
to be responsible for removing the map itself, bypassing the DRM's
automagic cleanup code.
Since the multi-master changes this has been broken, resulting in some
drivers having their registers unmapped before it's finished with them.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Calls to kcalloc() for a single element can be simplified to calls to
kzalloc().
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (244 commits)
Revert "x86, bts: reenable ptrace branch trace support"
tracing: do not translate event helper macros in print format
ftrace/documentation: fix typo in function grapher name
tracing/events: convert block trace points to TRACE_EVENT(), fix !CONFIG_BLOCK
tracing: add protection around module events unload
tracing: add trace_seq_vprint interface
tracing: fix the block trace points print size
tracing/events: convert block trace points to TRACE_EVENT()
ring-buffer: fix ret in rb_add_time_stamp
ring-buffer: pass in lockdep class key for reader_lock
tracing: add annotation to what type of stack trace is recorded
tracing: fix multiple use of __print_flags and __print_symbolic
tracing/events: fix output format of user stack
tracing/events: fix output format of kernel stack
tracing/trace_stack: fix the number of entries in the header
ring-buffer: discard timestamps that are at the start of the buffer
ring-buffer: try to discard unneeded timestamps
ring-buffer: fix bug in ring_buffer_discard_commit
ftrace: do not profile functions when disabled
tracing: make trace pipe recognize latency format flag
...
* 'x86-xen-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (42 commits)
xen: cache cr0 value to avoid trap'n'emulate for read_cr0
xen/x86-64: clean up warnings about IST-using traps
xen/x86-64: fix breakpoints and hardware watchpoints
xen: reserve Xen start_info rather than e820 reserving
xen: add FIX_TEXT_POKE to fixmap
lguest: update lazy mmu changes to match lguest's use of kvm hypercalls
xen: honour VCPU availability on boot
xen: add "capabilities" file
xen: drop kexec bits from /sys/hypervisor since kexec isn't implemented yet
xen/sys/hypervisor: change writable_pt to features
xen: add /sys/hypervisor support
xen/xenbus: export xenbus_dev_changed
xen: use device model for suspending xenbus devices
xen: remove suspend_cancel hook
xen/dev-evtchn: clean up locking in evtchn
xen: export ioctl headers to userspace
xen: add /dev/xen/evtchn driver
xen: add irq_from_evtchn
xen: clean up gate trap/interrupt constants
xen: set _PAGE_NX in __supported_pte_mask before pagetable construction
...
* 'irq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (76 commits)
x86, apic: Fix dummy apic read operation together with broken MP handling
x86, apic: Restore irqs on fail paths
x86: Print real IOAPIC version for x86-64
x86: enable_update_mptable should be a macro
sparseirq: Allow early irq_desc allocation
x86, io-apic: Don't mark pin_programmed early
x86, irq: don't call mp_config_acpi_gsi() if update_mptable is not enabled
x86, irq: update_mptable needs pci_routeirq
x86: don't call read_apic_id if !cpu_has_apic
x86, apic: introduce io_apic_irq_attr
x86/pci: add 4 more return parameters to IO_APIC_get_PCI_irq_vector(), fix
x86: read apic ID in the !acpi_lapic case
x86: apic: Fixmap apic address even if apic disabled
x86: display extended apic registers with print_local_APIC and cpu_debug code
x86: read apic ID in the !acpi_lapic case
x86: clean up and fix setup_clear/force_cpu_cap handling
x86: apic: Check rev 3 fadt correctly for physical_apic bit
x86/pci: update pirq_enable_irq() to setup io apic routing
x86/acpi: move setup io apic routing out of CONFIG_ACPI scope
x86/pci: add 4 more return parameters to IO_APIC_get_PCI_irq_vector()
...
This adds a driver for the ARM PL022 PrimeCell SSP/SPI
driver found in the U300 platforms as well as in some
ARM reference hardware, and in a modified version on the
Nomadik board.
Reviewed-by: Alessandro Rubini <rubini-list@gnudd.com>
Reviewed-by: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Based on Ingo Molnar's patch from 2006, this makes the floppy work after
resume from hibernation, at least on my machine.
This fix resets the floppy controller on resume. It was experimentally
determined to bring the controller back to life - we don't really know why
it works.
floppy_init() does the same thing at boot/modprobe time.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The "ramdisk" parameter was removed from the defunct rd.c file quite some
time ago, in favour of the more specific "ramdisk_size" parameter so, for
consistency, the same should be done here.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Acked-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
