We'll need this for proper channel tracking (which
is going to be needed for channel context
accounting and finding matching/active interface
combination).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This functionality will be reused when interface
is going down. Avoids code duplication. Also adds
missing wdev locking.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow drivers to advertise their VHT capabilities
and export them to userspace via nl80211.
Signed-off-by: Mahesh Palivela <maheshp@posedge.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the VHT definitions to be used by drivers supporting it.
Signed-off-by: Mahesh Palivela <maheshp@posedge.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
beacon_ies is needed only in order to extract the dtim
period. However, even if it's missing we can still enter
ps with dtim=1 (which also happens if the TIM ie is invalid).
Most drivers don't use conf.max_sleep_period/ps_dtim_period
anyway, and this check prevents them from entering ps if
they don't have beacon (but only probe response), even though
the beacon is not needed at all.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On deauth/disassoc we tear down all BA sessions. These
DELBA packets are sent on the appropriate TID, while
deauth/disassoc is always sent on VO. This sometimes
ends with the DELBA being sent after the deauth was
already sent.
Fix it by flushing all the pending frames before
sending deauth/disassoc.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This and ieee80211_add_ext_srates_ie() aren't
exported, so can't be used by drivers anyway,
but there's also no reason that they should be
so make them private to mac80211 and use sdata
instead of vif arguments.
Acked-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Wrap the MCI-work canceling with CONFIG_ATH9K_BTCOEX_SUPPORT.
Reported-by: Emmanuel Benisty <benisty.e@gmail.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "brcmfmac: introduce checkdied debugfs functionality"
also introduced a sparse warning:
..../brcmfmac/dhd_sdio.c:3147:45: sparse: cast to restricted __le32
This patch fixes this sparse warning.
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BCM4334 is a dualband a/b/g/n WiFi chip support 20MHz/40MHz
channels. This patch adds support for its SDIO interface.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The nvram data is preprocessed before being sent to the device
and just before sending an additional allocation was done that
assured word alignment of the data. This has moved to the
preprocessing step to reduce allocations and subsequent copying
of the nvram data.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The nvram file could be parsed directly in the data buffer in the
firmware structure passed by request_firmware function. This patch
gets rid of the redundant memcpy.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
txglomming alignment is a SDIO bus specific feature. It is more
appropriate to place it in SDIO bus layer instead of common layer.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
txglomming is a firmware feature for sdio bus interface. For SDIO
device cores newer than revision 11, the default setting of
firmware should be used instead of disabling it from the host side.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmfmac need to support data command setting for dongle's bus
core. A list must be placed at brcmf_bus structure before calling
brcmf_bus_start in order to be sent by brcmf_c_preinit_dcmds.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of them are BCM4706 specific AFAWK. Most of them was confirmed on
Netgear WNDR450.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When CONFIG_PM is disabled, no device can possibly
support WoWLAN since it can't go to sleep to start
with. Due to this, mac80211 had even rejected the
hardware registration. By making all the code and
data for WoWLAN depend on CONFIG_PM we can promote
this runtime error to a compile-time error.
Add #ifdef around all WoWLAN code to remove it in
systems that don't need it as they never suspend.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove the radio enable/disable stuff and fix the
transition to FULL_SLEEP mode when the device is idle.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 adds stations in HT IBSS as soon as a frame comes by,
even if the HT capabilities are not known yet (they are often
received later, e.g. in beacons). So far, ampdu factor/density
are only calculated when the station is initially added.
This patch changes this to update ampdu factor/density settings
when starting a blockack session.
Using this patch, we had performance boosts from 60 to 150 MBit/s
between two 2x2 Atheros devices in 5 GHz HT IBSS mode.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The command "make includecheck" yields the following for the rtlwifi tree:
/home/finger/linux-2.6/drivers/net/wireless/rtlwifi/rtl8192se/sw.c: ../pci.h is included more than once.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As recovery queuing can now occur from multiple code paths
it's convenient to know what triggered it in all cases
other than an intended recovery which is part of the
switch between single role to multi role.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Following the addition of propagating errors from the bus ops
there's a need to distinguish between bus errors (including timeout)
and a legitimate timeout occuring in cmd_wait_for_event_or_timeout.
In case of real bus errors we need to queue recovery even in cases
where a timeout on a response from the FW to a command is acceptable.
Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
commit 14bba17b "wl12xx: Propagate errors from wl1271_raw_write32"
breaks down TX in certain scenarios. wl1271_irq_locked() propagates
errors from wl1271_tx_work_locked however it may return -EBUSY
when the FW queues are full which is a legitimate case and not a
a real error. In this case a recovery is triggered by wl1271_irq
and this keeps repeating itself so TX is completely broken.
Fix it by avoiding propagating return values as errors even if they
aren't. Only bus (SDIO or SPI) ops failures would be progagated
as only these should trigger recovery.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We need to release the IRQ if hw_info() or identify_chip() fails. And
we need unregister the HW with mac80211 if there are any failures
after it's registered.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The new PG2 version of the chip has a few differences in terms of FW
API if compared to PG1. PG1 is just a sample that shouldn't be used
in real life, so to avoid having to handle both separately, mark the
PG1 version as deprecated and bail out during probe.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Since it's not called from any file outside where
it's defined, the function can be static if moved
up in the file before the callers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_check_concurrent_iface() need not use the
netdev. Remove the use of the netdev here to prepare
the function for P2P device addition.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support configuring an RSSI threshold in dBm (s32) when requesting
scheduled scan, below which a BSS won't be reported by the cfg80211
driver.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code is fine in both cases as-is, but we can
write it slightly differently to fix smatch/sparse
complaints:
* compare the skb pointer (which we use as a cookie)
by casting the skb to unsigned long rather than the
cookie to a pointer (fixes "different address spaces")
* when transmitting, data->channel must be assigned,
don't check it (fixes "dereferenced before check")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It can be very useful to have all debug messages
available when debugging, but hard to correlate
between different sources, so add a trace event
for all mac80211 debug messages.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few things that make the logging and
debugging in mac80211 less useful than it should
be right now:
* a lot of messages should be pr_info, not pr_debug
* wholesale use of pr_debug makes it require *both*
Kconfig and dynamic configuration
* there are still a lot of ifdefs
* the style is very inconsistent, sometimes the
sdata->name is printed in front
Clean up everything, introducing new macros and
separating out the station MLME debugging into
a new Kconfig symbol.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Take the mutex early in the resume handler and use the locked version of
the IRQ routine. This ensures any recoveries queued will only take place
after resume has fully completed.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Separate the threaded IRQ handling routine into two functions.
The outer function takes the mutex and calls recovery on errors. It also
performs a Tx-path optimization to avoid redundant works.
The inner function is simplified - all calls to recovery are removed and
it assumes the lock is taken. The locked variant will be reused elsewhere.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Propagate some missing return values for Rx-filter related functions.
This and makes sure we always fail the suspend in case of SDIO errors.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
If an error is detected after mac80211 is already suspended, the recovery
work will not be queued. This will leave the driver in a bad state on
resume.
Detect this in the resume op and re-queue a recovery.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Set a flag and after the first read/write failure is encountered.
This flag will disallow further SDIO read/writes until op_stop() is
executed, which will clear all flags.
This prevents further errors from occurring, since one error usually
indicates that IO operations won't work anymore until the chip is
rebooted. By blocking more calls, we avoid extra timeouts and having
to wait for them to occur.
[Added second paragraph explaining why the change is needed. -- Luca]
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We wish to postpone suspend if recovery is pending. This will make sure
the FW is in a good state and perform wowlan wakeup.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Applications running in the user space needs access to the
memory of the chip. Examples of such access
- read/write global variables
- access to firmware log
- dump memory after firmware panic event
Arbitrary 4-bytes aligned location can be accessed by
read/write file wlcore/mem
[Check return value of wlcore_raw_read/write and wlcore_set_partition
calls as required by the recent IO changes. -- Luca]
Signed-off-by: Arkady Miasnikov <a-miasnikov@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When running in AP mode, the driver reports all deletions from CAM in
a cryptic manner that makes users think it is an error. change so that
the condition is only reported at higher-levels of debugging.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename mrcCCKOff for better code readability and also fixes
the smatch warning.
drivers/net/wireless/ath/ath9k/ar9003_phy.c:982
ar9003_hw_ani_control() Error invalid range 1 to 0.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
