Patch from David Brownell
Remove buld warning when building sa1111 on non-sa1100 platforms (e.g. PXA).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Paul Sokolovsky
This patch adds timeouts while working with SSP registers. Such
timeouts were envisioned by docstrings in ssp.c, but were not
implemented. There were actual lockups while accessing
touchscreen for iPaqs h1910, h4000 due to lack of the timeouts.
This is updated version of previously submitted patch: 3738/1.
Signed-off-by: Paul Sokolovsky <pmiscml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Daniel Jacobowitz
The fcvtds and fcvtsd instructions were generating a qnan bit pattern
for both quiet and signalling NaNs.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Daniel Jacobowitz
The fcvtsd/fcvtds emulation was left behind when the numbering of double
precision registers was changed from 0-30 to 0-15. Both conversion
instructions were writing their results to the wrong register. Also,
the conversion instructions should stop after the first element even
if a vector length is specified.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Daniel Jacobowitz
The recent fix to hide VFP_NAN_FLAG broke the check in vfp_raise_exceptions;
it would attempt to deliver an exception mask of 0xfffffeff instead of reporting
a serious error condition using printk. Define a safe constant to use for
an invalid exception maskm, and use it at both ends.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Here is a patch that adds support for the Instashield IS-200 2 port PCI
serial card.
Signed-off-by: Peter Horton <pdh@colonel-panic.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes CCID3 to give much closer performance to RFC4342.
CCID3 is meant to alter sending rate based on RTT and loss.
The performance was verified against:
http://wand.net.nz/~perry/max_download.php
For example I tested with netem and had the following parameters:
Delayed Acks 1, MSS 256 bytes, RTT 105 ms, packet loss 5%.
This gives a theoretical speed of 71.9 Kbits/s. I measured across three
runs with this patch set and got 70.1 Kbits/s. Without this patchset the
average was 232 Kbits/s which means Linux can't be used for CCID3 research
properly.
I also tested with netem turned off so box just acting as router with 1.2
msec RTT. The performance with this is the same with or without the patch
at around 30 Mbit/s.
Signed off by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge-netfilter code will overwrite memory if there is not
headroom in the skb to save the header. This first showed up when
using Xen with sky2 driver that doesn't allocate the extra space.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[DCCP]: Introduce dccp_rx_hist_find_entry
[DCCP]: Introduces follows48 function
[DCCP]: Update contact details and copyright
[DCCP]: Fix typo
[IPV6]: Segmentation offload not set correctly on TCP children
[CONNECTOR]: Add userspace example code into Documentation/connector/
This adds a new function dccp_rx_hist_find_entry.
Signed off by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a new function to see if two sequence numbers follow each
other.
Signed off by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a small typo in net/dccp/libs/packet_history.c
Signed off by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP over IPV6 would incorrectly inherit the GSO settings.
This would cause kernel to send Tcp Segmentation Offload packets for
IPV6 data to devices that can't handle it. It caused the sky2 driver
to lock http://bugzilla.kernel.org/show_bug.cgi?id=7050
and the e1000 would generate bogus packets. I can't blame the
hardware for gagging if the upper layers feed it garbage.
This was a new bug in 2.6.18 introduced with GSO support.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I was asked several times to include userspace example code into
Documentation, so if there is no policy against it, consider attached patch
for 2.6.18. This program works with included Documentation/connector/cn_test.c
connector module.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current sun disklabel code uses a signed int for the sector count.
When partitions larger than 1 TB are used, the cast to a sector_t causes
the partition sizes to be invalid:
# cat /proc/paritions | grep sdan
66 112 2146435072 sdan
66 115 9223372036853660736 sdan3
66 120 9223372036853660736 sdan8
This patch switches the sector count to an unsigned int to fix this.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It moves the smp_procesors_ready variable to sun4d_smp.c only.
Signed-off-by: Krzysztof Helt (krzysztof.h1@wp.pl)
Signed-off-by: David S. Miller <davem@davemloft.net>
smp_setup_cpu_possible_map() needs to run after paging_init()
so that the in-kernel device tree is setup.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing unusual_devs entry for the UCR-61S2B appears to have too
wide a revision range. It matches at least one device that doesn't
respond to the initialization sequence. Perhaps the sequence needs to
be updated, or perhaps something else can be done. For now, this patch
(as764) restricts the range to include only the revision mentioned in
the original comment.
This resolves (for now!) Bugzilla entry #6950.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes support for a clone of Nokia DKU-5 cable made by Ours
Technology Inc, as it turned out that the cable does not use the pl2303
chip, but OTI-6858 chip which is not compatible with the pl2303.
Signed-off-by: Tomasz Kazmierczak <tomek.fizyk@op.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This was pointed out by Adrian Bunk <bunk@stusta.de>, as found by the Coverity Checker.
Cc: Adrian Bunk <bunk@stusta.de>
Cc: Oliver Bock <o.bock@fh-wolfenbuettel.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removes an unused kerneldoc entry from pci_match_device and
put the others into correct order.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a patch against the CPCI hotplug core to fix up PCI resource
assignment such that things will actually work when a hot inserted
device is enabled. I mentioned this patch to you way back in April at
ELC, but am only now out from under things enough to clean it up and
submit it. I've basically cribbed the corresponding code from
shpchp_pci.c, so there are no big surprises. If it's still possible, I
wouldn't mind this going into 2.6.18, but it wouldn't be the end of the
world if it went into 2.6.19.
Signed-off-by: Scott Murray <scottm@somanetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- add the ICH6(R) LPC to the ICH6 ACPI quirks. currently only the ICH6-M
is handled. [ PCI_DEVICE_ID_INTEL_ICH6_1 is the ICH6-M LPC, ICH6_0 is
the ICH6(R) ]
- remove the wrong quirk calling asus_hides_smbus_lpc() for ICH6. the
register modified in asus_hides_smbus_lpc() has a different meaning in
ICH6.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On i386 PCI mmconfig forgets the bus number when setting the fallback_slots
bits which means fallback to conf1 only works for bus 0.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
there was a change in 2.6.17 which affected the order in which the PCI
access methods are probed. this gives regressions on some machines with
broken BIOS. the problem is that PCBIOS sometimes reports last bus wrong,
leaving cardbus non-funcational. previously those system worked fine with
direct access.
The patch changes the PCI init code to have PCBIOS as last fallback, yet
the PCBIOS code still has to run first to set pcibios_last_bus to the value
reported by the BIOS. this is needed in case legacy PCI probing
(arch/i386/pci/legacy.c) is used to detect peer busses. using direct
access if available fixes the cardbus problems.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch contains 2 sets of fixes for the abituguru:
1) Much improved timeout handling, drasticly reducing the amount of
timeout errors on some motherboards
2) Fix the exit paths in the bank1 sensor type detect code to always
restore the original settings even on an error. Without this our
special test settings could remain seriously confusing the system
BIOS's setup menu.
Both are very much related and are must haves, to avoid messing up the
uguru CMOS settings.
Detailed changes:
- Much improved timeout / wait for status handling. Many thanks to Sunil
Kumar, for all his testing, ideas and patches! The code now first busy
waits, polling the uguru for the expected status as this usually
succeeds pretty quickly (within 90 reads). To avoid unnecessary CPU burn
in timeout conditions, the amount of busy waiting has been halved from
previous versions (120 tries instead of 250). This is not a problem,
because this version goes to sleep after 120 attemps for 1 jiffy and
then tries again, it does this sleep and try again 5 times before
finally giving up. This (almost?) completly removes the timeout errors
some people have seen regulary. Apparently some older uguru versions
sometimes are distracted for a (relatively) long time. This solves this.
- These timeout errors not only occur in the sending address part of
reading the uguru but also in the wait for read state, so errors in
this state are now handled as retryable just like send address state
errors and are only logged and reported to userspace if 3 executive
tries fail.
- Fix a very nasty bug in the bank1 sensor type detection code, where it
would not restore the original settings in any of the error paths!
- Since not successfully restoring the original settings can seriously
confuse the system BIOS (hang when entering the relevant setup menu),
we now try restoring them 3 times before giving up.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The tps65010.c driver in the main tree never got updated with
build fixes since the last batch of I2C driver changes; and the
genirq trigger flags were updated wierdly too.
This also includes a minor tweak to reduce the frequency used to
poll for unplug-the-AC-power on the TPS chips that don't provide
relevant IRQs. It _would_ be nice to sense whether there's even
a battery, but that'd normally be an HDQ/1-wire interface to a
smart battery, and such APIs aren't standardized.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The callers of scsi_send_eh_cmnd are setting the cmnd buffer,
and then scsi_send_eh_cmnd is copying that updated buffer to
the old_cmnd variable. Then after the command runs, we end up
copying that old_cmnd var which has the new cmnd to the scsi
command buffer. When this command gets recent, all types of fun
things happen like getting TUR or START_STOP commands with
data and scatterlists.
This patch made against scsi-rc-fixes, has the callers of
scsi_send_eh_cmnd pass in the command so scsi_send_eh_cmnd
can do the right thing. This should go into 2.6.18 since this
fixes a regression added when we removed some of the scsi_cmnd
fields and replaced them with local variables.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Software must explicitely re-enable extended firmware tracing
after any ISP abort condition.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original code attempts to retry PLOGIs to fcports that are
FCP_TARGETs only. If the driver never performed a successful
PLOGI/PRLI, the port-type would never be assigned, and the
relogin logic would silently drop the request (and thus the port
would not be recognized and registered).
The fix is relatively straightforward, drop the FCP_TARGET-only
check.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's a problem where sg is executing a ->nopage operation on a
compound page, it actually calls get_page() on the first page in the
compound rather than the page which is being mapped. The fix is to
select the correct page by indexing into the compound.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
since only the briQ has a briQ front panel, and the briQ is a CHRP and
is only supported if CONFIG_PPC_CHRP is set.
Signed-off-by: Paul Mackerras <paulus@samba.org>
After going through the trouble of setting up the PIC base
address in the pic@40000 device tree node, use it instead
of the obsolete hard-coded value.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PIN_SIZE definition name changed, update 44x_mmu.c accordingly.
Signed-off-by: Matt Porter <mporter@embeddedalley.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Removes the flush_dcache_all export for non coherent platforms.
We removed the last in-kernel user of this years ago in arch/ppc
so it no longer serves a purpose. Plus, it breaks the build
at the moment.
Signed-off-by: Matt Porter <mporter@embeddedalley.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds 'powerpc' architecture support to checkstack.pl.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Only call into RTAS when booted with panic=0 because the RTAS call
does not return. The system has to be rebooted via the HMC or via the
management console right now. This is cumbersome and not what the
default panic=180 is supposed to do.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
gcc 4.1 produces some warnings that say it is ignoring the packed
attribute on some structure elements, so, since all the elements of
these structs are packed, pack the structs instead.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Several RTAS calls take a "config_addr" parameter, which is a particular
way of specifying a PCI busno, devfn and register number into a 32-bit word.
Currently these are open-coded, and I'll be adding another soon, replace
them with a helper that encapsulates the logic. Be more strict about masking
the busno too, just in case.
Booted on P5 LPAR.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Just one bit of fallout from the constification of the get_property
return value.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The rtas console doesn't have to be Cell specific. If we get both
RTAS tokens, we should just enabled the console then and there.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cleanup CPU inits a bit more, Geoff Levand already did some earlier.
* Move CPU state save to cpu_setup, since cpu_setup is only ever done
on cpu 0 on 64-bit and save is never done more than once.
* Rename __restore_cpu_setup to __restore_cpu_ppc970 and add
function pointers to the cputable to use instead. Powermac always
has 970 so no need to check there.
* Rename __970_cpu_preinit to __cpu_preinit_ppc970 and check PVR before
calling it instead of in it, it's too early to use cputable.
* Rename pSeries_secondary_smp_init to generic_secondary_smp_init since
everyone but powermac and iSeries use it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rename cpu_setup_power4.S to cpu_setup_ppc970.S, since that's
really what it is.
No functional or other changes.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
