* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (95 commits)
b44: GFP_DMA skb should not escape from driver
korina: do not use IRQF_SHARED with IRQF_DISABLED
korina: do not stop queue here
korina: fix handling tx_chain_tail
korina: do tx at the right position
korina: do schedule napi after testing for it
korina: rework korina_rx() for use with napi
korina: disable napi on close and restart
korina: reset resource buffer size to 1536
korina: fix usage of driver_data
bnx2x: First slow path interrupt race
bnx2x: MTU Filter
bnx2x: Indirection table initialization index
bnx2x: Missing brackets
bnx2x: Fixing the doorbell size
bnx2x: Endianness issues
bnx2x: VLAN tagged packets without VLAN offload
bnx2x: Protecting the link change indication
bnx2x: Flow control updated before reporting the link
bnx2x: Missing mask when calculating flow control
...
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon: (abituguru3) Fix CONFIG_DMI=n fallback to probe
hwmon: (abituguru3) Enable DMI probing feature on IN9 32X MAX
hwmon: (abituguru3) Match partial DMI board name strings
hwmon: Add a driver for the ADT7475 hardware monitoring chip
hwmon: (k8temp) Fix temperature reporting for (most) K8 RevG CPUs
hwmon: (k8temp) Fix wrong sensor selection for AMD K8 RevF/RevG CPUs
hwmon: (k8temp) Warn about fam F rev F errata
If INET=y and INFINIBAND=y, but IPV6=m then INFINIBAND_ADDR_TRANS is set
to n and the RDMA CM functions rdma_connect() et al are not built.
However, the current config dependencies allow NET_9P_RDMA to be selected
in this, which leads to a build failure. Fix this by adding a dependency
on INFINIBAND_ADDR_TRANS to disallow NET_9P_RDMA in this case.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We used to just write changed page for IS_DIRSYNC inodes. But we also
have to update the directory inode itself just for the case that we've
allocated a new block and changed i_size.
[akpm@linux-foundation.org: still sync the data page]
Signed-off-by: Jan Kara <jack@suse.cz>
Tested-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Carry out the PM-routine interface change in the USB OTG pathway. This
was omitted from the earlier interface-change patch by mistake.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg KH <greg@kroah.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: fix 15 make headers_check warnings:
include of <linux/types.h> is preferred over <asm/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(suppose: memcg->use_hierarchy == 0 and memcg->swappiness == 60)
echo 10 > /memcg/0/swappiness |
mem_cgroup_swappiness_write() |
... | echo 1 > /memcg/0/use_hierarchy
| mkdir /mnt/0/1
| sub_memcg->swappiness = 60;
memcg->swappiness = 10; |
In the above scenario, we end up having 2 different swappiness
values in a single hierarchy.
We should hold cgroup_lock() when cheking cgrp->children list.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Paul Menage <menage@google.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At system boot when creating the top cgroup, mem_cgroup_create() calls
enable_swap_cgroup() which is marked as __init, so mark
mem_cgroup_create() as __ref to avoid false section mismatch warning.
Reported-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by; KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The LED on HP notebooks is connected through ACPI. That unfortunately
means that it needs to be delayed by using schedule_work() to avoid
calling the ACPI interpreter from an invalid context.
[akpm@linux-foundation.org: use flush_work() rather than sort-of reimplementing it]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix lis3 documentation to fit into 80 columns.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the second part of the HP laptop disk protection functionality (a red
led) to the same driver. From a purely Linux developer's point of view,
the led and the accelerometer have nothing related. However, they
correspond to the same ACPI functionality, and so will always be used
together, moreover as they share the same ACPI PNP alias, there is no
other simple to allow to have same loaded at the same time if they are not
in the same module. Also make it requires the led class to compile and
update the Kconfig text.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David points out that the idr_remove_all() function returns unused slabs
to the kmem cache, but needs to zero them first or else they will be
uninitialized upon next use. This causes crashes which have been observed
in the firewire subsystem.
He fixed this by zeroing the object before freeing it in idr_remove_all().
But we agree that simply removing the constructor and zeroing the object
at allocation time is simpler than relying upon slab constructor machinery
and might even be faster.
This problem was introduced by "idr: make idr_remove rcu-safe" (commit
cf481c20c4), which was first released in
2.6.27.
There are no known codesites which trigger this bug in 2.6.27 or 2.6.28.
The post-2.6.28 firewire changes are the only known triggerer.
There might of course be not-yet-discovered triggerers in 2.6.27 and
2.6.28, and there might be out-of-tree triggerers which are added to those
kernel versions. I'll let the -stable guys decide whether they want to
backport this fix.
Reported-by: David Moore <dcm@acm.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Nadia Derbey <Nadia.Derbey@bull.net>
Cc: Paul E. McKenney <paulmck@us.ibm.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Kristian Hgsberg <krh@redhat.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As it's just a single call to __get_free_page().
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Unlike other alphas, marvel doesn't have real PC-style CMOS clock hardware
- RTC accesses are emulated via PAL calls. Unfortunately, for unknown
reason these calls work only on CPU #0. So current implementation for
arbitrary CPU makes CMOS_READ/WRITE to be executed on CPU #0 via IPI.
However, for obvious reason this doesn't work with standard
get/set_rtc_time() functions, where a bunch of CMOS accesses is done with
disabled interrupts.
Solved by making the IPI calls for entire get/set_rtc_time() functions,
not for individual CMOS accesses. Which is also a lot more effective
performance-wise.
The patch is largely based on the code from Jay Estabrook.
My changes:
- tweak asm-generic/rtc.h by adding a couple of #defines to
avoid a massive code duplication in arch/alpha/include/asm/rtc.h;
- sys_marvel.c: fix get/set_rtc_time() return values (Jay's FIXMEs).
NOTE: this fixes *only* LIB_RTC drivers. Legacy (CONFIG_RTC) driver
wont't work on marvel. Actually I think that we should just disable
CONFIG_RTC on alpha (maybe in 2.6.30?), like most other arches - AFAIK,
all modern distributions use LIB_RTC anyway.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recently introduced generic pci_common_swizzle() relies on bus->self
being NULL for the root PCI bus. But on nautilus bus->self points to
the host bridge device, which is necessary as we do a root bus sizing
on this system. As a result, pci_common_swizzle() loops infinitely.
This worked until 2.6.29-rc1 because the alpha-specific swizzle routine
checked for bus->parent == NULL (instead of bus->self).
Fixed by clearing bus->self after bus sizing is done.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
init_srm_irq() deals with irq's #16 and above, but size of irq_desc
array on nautilus and some other system types is 16. So gcc-4.3
complains that "array subscript is above array bounds", even though
this function is never called on those systems.
This adds a check for NR_IRQS <= 16, which effectively optimizes
init_srm_irq() code away on problematic platforms.
Thanks to Daniel Drake <dsd@gentoo.org> for detailed analysis
of the problem.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In previous implementation, mem_cgroup_try_charge checked the return
value of mem_cgroup_try_to_free_pages, and just retried if some pages
had been reclaimed.
But now, try_charge(and mem_cgroup_hierarchical_reclaim called from it)
only checks whether the usage is less than the limit.
This patch tries to change the behavior as before to cause oom less
frequently.
Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If root_mem has no children, last_scaned_child is set to root_mem itself.
But after some children added to root_mem, mem_cgroup_get_next_node can
mem_cgroup_put the root_mem although root_mem has not been mem_cgroup_get.
This patch fixes this behavior by:
- Set last_scanned_child to NULL if root_mem has no children or DFS
search has returned to root_mem itself(root_mem is not a "child" of
root_mem). Make mem_cgroup_get_first_node return root_mem in this case.
There are no mem_cgroup_get/put for root_mem.
- Rename mem_cgroup_get_next_node to __mem_cgroup_get_next_node, and
mem_cgroup_get_first_node to mem_cgroup_get_next_node. Make
mem_cgroup_hierarchical_reclaim call only new mem_cgroup_get_next_node.
Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a bug in error path of mem_cgroup_move_parent.
Extra refcnt got from try_charge should be dropped, and usages incremented
by try_charge should be decremented in both error paths:
A: failure at get_page_unless_zero
B: failure at isolate_lru_page
This bug makes this parent directory unremovable.
In case of A, rmdir doesn't return, because res.usage doesn't go down to 0
at mem_cgroup_force_empty even after all the pc in lru are removed.
In case of B, rmdir fails and returns -EBUSY, because it has extra ref
counts even after res.usage goes down to 0.
Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The light sensors ALV0 and ALV1 on newer MacBooks (early 2008 and later)
changed to report 10 bytes instead the earlier 6, and the sensor encoding
subsequently changed. As a result, the reported light sensors readings
are much too low.
Via experiments leading up to this patch, it seems only the ALV0 is
reporting data, and the most useful value therein is a 10-bit big-endian
value at offset 6. This suggests that a new protocol was added as a
backward-compatible replacement on top of the old one.
This patch makes applesmc report the improved light sensor reading for the
new machines, on a scale in conformance with earlier ones.
Signed-off-by: Alex Murray <murray.alex@gmail.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the general use case struct seq_operations should be a const object.
Check for and warn where it is not.
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We should not be continuing a braced section with an if, for example:
if (...) {
} if (...) {
}
Detect this and suggest adding a newline.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we allow return to have surrounding parentheses when containing
comparison operators we are not correctly handling the case where the
values contain array sufffixes. Squash them.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We should not be complaining about the prefix spacing for types and casts.
We are triggering here because the check for spacing between '*'s is
overly loose. Tighten this up.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the #if opening statement is not in the context then the context stack
can be empty. Handle this by ensuring there is always a blank entry in
the stack.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Tested-by: Dhaval Giani <dhaval@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Two nbd-clients at same time are bad idea, and cause WARN_ON from nbd in
2.6.28-rc7 from sysfs_add_one. This simply prevents that from happening.
To reproduce:
cat /dev/zero | head -c 10000000 > /tmp/delme.fstest.fs
nbd-server 9100 -l /anyone.can.connect > /tmp/delme.fstest.fs &
sleep 1
nbd-client localhost 9100 /dev/nd0 &
nbd-client localhost 9100 /dev/nd0 &
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the standard magic.h for btrfs and squashfs.
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Cc: Phillip Lougher <phillip@lougher.demon.co.uk>
Cc: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that people are using freezer for non-suspend/hibernation stuff, it
should have separate maintainers entry so that it is easier to find.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix __request_region() parameter kernel-doc notation and parameter name:
Warning(linux-2.6.28-git10//kernel/resource.c:627): No description found for parameter 'flags'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix jbd header file kernel-doc notation:
Warning(linux-2.6.28-git13//include/linux/jbd.h:823): No description found for parameter 'j_average_commit_time'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When no option is passed to getdelays it just hangs, waiting
for a reply which will never come.
This patch prints usage() when no output marker is specified.
Signed-off-by: Marcus Meissner <meissner@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
idr_get_new_above() and ida_get_new_above() return an id in the range of
@staring_id ... 0x7fffffff, not 0 ... 0x7fffffff.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- move CONFIG_PROC_PID_CPUSET into cgroup menu
- move MM_OWNER to the bottom for better menu indent
- fix typos
- use tabs not spaces
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Enable ring indicator interrupt.
- Remove vendor specific CVS version tags.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After XPC has been up and running on multiple partitions for any length of
time, if XPC on one of the partitions is stopped and restarted (either by
a rmmod/insmod or a system restart), it is possible for the XPCs running
on the other partitions to falsely detect a lack of heartbeat from the XPC
that was just restarted. This false detection will occur if the restarted
XPC comes up within the five-seconds preceding one of the other XPC's
heartbeat check (which occurs once every twenty seconds).
The detection of no heartbeat results in the detecting XPC deactivating
from the just restarted XPC. The only remedy is to restart one of the
XPCs and hope that one doesn't hit this five-second window on any of the
other partitions.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A triggering RTC alarm should be able to power on a device that has been
powered off. This patch enables that on twl4030 by not masking the alarm
interrupt at shutdown.
Signed-off-by: Matti Halme <matti.halme@nokia.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix these build errors:
CC drivers/rtc/rtc-pxa.o
drivers/rtc/rtc-pxa.c: In function `pxa_rtc_init':
drivers/rtc/rtc-pxa.c:472: error: implicit declaration of function `cpu_is_pxa27x'
drivers/rtc/rtc-pxa.c:472: error: implicit declaration of function `cpu_is_pxa3xx'
Signed-off-by: Antonio Ospite <ao2@openezx.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an explanitory comment as to why we modify the kernel console loglevel
rather than simply moving sysrq messages to KERN_EMERG level.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Document the interactions between loglevel and the sysrq output. Also
document how to work round it should output be required on the console.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Cc: Martin Mares <mj@ucw.cz>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
git is maintaining the last update time much more accuratly than the
internal update time. Remove it.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
i5400 EDAC driver were added upstream by those changesets:
- 920c8df6ac "edac: driver for i5400 MCH (Seaburg)"
- 8375d4909a "edac: driver for i5400 MCH (update)"
Update MAINTAINERS entry for this file to correspond to the driver
maintainer.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Ben Woodard <woodard@redhat.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On alpha, we have to map some stuff in the VMALLOC space very early in the
boot process (to make SRM console callbacks work and so on, see
arch/alpha/mm/init.c). For old VM allocator, we just manually placed a
vm_struct onto the global vmlist and this worked for ages.
Unfortunately, the new allocator isn't aware of this, so it constantly
tries to allocate the VM space which is already in use, making vmalloc on
alpha defunct.
This patch forces KVA to import vmlist entries on init.
[akpm@linux-foundation.org: remove unneeded check (per Johannes)]
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Force fb_var_screeninfo color format on all Blackfin Framebuffer Drivers.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
