Commit Graph

64371 Commits

Author SHA1 Message Date
Jan-Bernd Themann
a8e34fda79 ehea: fix interface to DLPAR tools
Userspace DLPAR tool expects decimal numbers to be written to
and read from sysfs entries.

Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-25 02:31:15 -04:00
Ralf Baechle
e3efb05468 sgiseeq: Fix return type of sgiseeq_remove
The driver remove method needs to return an int not void.  This was just
never noticed because usually this driver is not being built as a module.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-25 02:31:13 -04:00
Stephen Hemminger
c2cb71fafb sky2 1.17
Mark new version to track if current driver is in use.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-25 02:31:11 -04:00
Stephen Hemminger
32c2c30085 sky2: only bring up watchdog if link is active
This fixes the extra timer overhead that people were whining about
as a 2.6.23 regression.

Running the watchdog timer all the time is unneeded. Change it
to run only if link is up, and reduce frequency to save power.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-25 02:31:08 -04:00
Stephen Hemminger
b23457737f sky2: clear PCI power control reg at startup
Make sure PCI register for PHY power gets cleared on boot, and make
sure to avoid any PCI posting problems.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-25 02:31:06 -04:00
Florian Westphal
c46ac9463f DM9000: fix interface hang under load
When transferring data at full speed, the DM9000 network interface
sometimes stops sending/receiving data. Worse, ksoftirqd consumes
100% cpu and the net tx watchdog never triggers.
Fix by spin_lock_irqsave() in dm9000_start_xmit() to prevent the
interrupt handler from interfering.

Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-25 02:31:04 -04:00
Domen Puncer
bc1e0a095e phy layer: fix genphy_setup_forced (don't reset)
Writing BMCR_RESET bit will reset MII_BMCR to default values. This is
clearly not what we want.

Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-25 02:31:02 -04:00
Ralf Baechle
09e06f652d Don't use GFP_DMA for zone allocation.
IP32 doesn't even have a ZONE_DMA so no point in using GFP_DMA in any
IP32-specific device driver.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-25 02:30:59 -04:00
Willy Tarreau
ba685fb2ab fix realtek phy id in forcedeth
As noticed by Chuck Ebbert, commit c5e3ae8823
introduced a copy-paste typo, as realtek phy is 0x732 and not 0x1c1. Obvious
fix below suggested by Ayaz Abdulla.

Signed-off-by: Willy Tarreau <w@1wt.eu>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-25 02:30:57 -04:00
Linus Torvalds
1a8f46100b Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: don't check n_sectors during revalidation if zero
  pata_via: Add Arima W730-K8 and other rebadgings
  pata_sis: Add the FSC Amilo and friends
  pata_pdc2027x: PLL detection fixes
  libata: fix n_sectors failure handling during revalidation
2007-08-23 21:40:33 -07:00
Linus Torvalds
b1b8aca480 Merge master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6.23
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6.23:
  sh: missing symbol fix for sh4-202
  sh: Fix DSP opcode regression for SH3-DSP parts.
2007-08-23 21:40:07 -07:00
Jesper Juhl
abcb1ff326 tty: dont needlessly cast kmalloc() return value
kmalloc() hands us a void pointer, we don't need to cast it.

Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-08-23 21:39:41 -07:00
Linus Torvalds
87bd1e9aaf Merge branch 'master' of ssh://master.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb
* 'master' of ssh://master.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
  V4L/DVB (6070): Fix a warning at dvb_net
  V4L/DVB (6042): b2c2-flexcop: fix Airstar HD5000 tuning regression
2007-08-23 21:38:54 -07:00
Linus Torvalds
d0797b39dc Merge git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched
* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
  sched: tweak the sched_runtime_limit tunable
  sched: skip updating rq's next_balance under null SD
  sched: fix broken SMT/MC optimizations
  sched: accounting regression since rc1
  sched: fix sysctl directory permissions
  sched: sched_clock_idle_[sleep|wakeup]_event()
2007-08-23 21:38:39 -07:00
Linus Torvalds
0542170dec Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
  9p: fix bad error path in conversion routines
  9p: remove deprecated v9fs_fid_lookup_remove()
  9p: update maintainers and documentation
  9p: fix use after free
2007-08-23 21:38:21 -07:00
Miloslav Trmac
6dc2c1b779 Renumber AUDIT_TTY_[GS]ET
Renumber AUDIT_TTY_[GS]ET to avoid a conflict with netlink message types
already used in the wild.

Signed-off-by: Miloslav Trmac <mitr@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-08-23 21:37:45 -07:00
Linus Torvalds
1ff6f3dbfb Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
  sdhci: tell which spurious interrupt we got
  sdhci: handle data interrupts during command
  mmc: ignore bad max block size in sdhci
  sdhci: be more cautious about block count register
  drivers/mmc/core/host.c: kmalloc + memset conversion to kzalloc
  drivers/mmc/core/bus.c: kmalloc + memset conversion to kzalloc
2007-08-23 21:36:13 -07:00
Linus Torvalds
2b56fec64f Merge master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
  PCI: Run k8t_sound_hostbridge quirk only when needed
  PCI: disable MSI on RX790
  PCI: disable MSI on RD580
  PCI: disable MSI on RS690
  PCI: make pcie_get_readrq visible in pci.h
  PCI: lets kill the 'PCI hidden behind bridge' message
  pci/hotplug/cpqphp_ctrl.c: remove stale BKL use
  PCI: Document pci_iomap()
  PCI: quirk_e100_interrupt() called too early
  PCI: Move prototypes for pci_bus_find_capability to include/linux/pci.h
2007-08-23 21:35:45 -07:00
Linus Torvalds
9e1a3e31cb Merge master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (35 commits)
  usb: add PRODUCT, TYPE to usb-interface events
  USB: resubmission unusual_devs modification for Nikon D80
  usb quirks: Add Canon EOS 5D (PC Connection mode) to the autosuspend blacklist
  USB: make EHCI initialize properly on PPC SOCs
  UEAGLE: Remove sysfs files on error case
  USB: fsl_usb2_udc: fix bug in processing setup requests
  USB: g_file_storage: fix bug in DMA buffer handling
  USB: update last_busy field correctly
  USB: fix DoS in pwc USB video driver
  USB: allow retry on descriptor fetch errors
  USB: unkill cxacru atm driver
  USB: Adding support for HTC Smartphones to ipaq
  USB: another quirky device
  USB: quirky mass storage device
  USB: ohci, fix oddball gcc warning
  usb-storage: fix bugs in the disconnect pathway
  usb: typo in usb R8A66597 HCD config
  USB: accept 1-byte Device Status replies, fixing some b0rken devices
  USB: blacklist Samsung ML-2010 printer
  usb-serial: fix oti6858.c segfault in termios handling
  ...
2007-08-23 21:35:04 -07:00
Linus Torvalds
de80af4cc9 Merge master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6:
  sysfs: don't warn on removal of a nonexistent binary file
  HOWTO: latest lxr url address changed
  HOWTO: korean translation of Documentation/HOWTO
  Fix Off-by-one in /sys/module/*/refcnt
  sysfs: fix locking in sysfs_lookup() and sysfs_rename_dir()
2007-08-23 21:34:43 -07:00
Greg Ungerer
405d296559 m68knommu: include linux/fs.h for do_pipe()
Include linux/fs.h to get the prototype for do_pipe().
Build fix.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-08-23 21:32:54 -07:00
Greg Ungerer
01740fccba m68knommu: include asm-generic/pgtable.h
Include asm-generic/pgtable.h to pick up the lazy_mmu_mode and
lazy_cpu_mode macros. Won't build without them.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-08-23 21:32:54 -07:00
Greg Ungerer
07ef30932e m68knommu: include linux/fs.h for getname()
Include linux/fs.h to get the prototype for getname().
Build fix.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-08-23 21:32:54 -07:00
Alan Cox
604de6e0ee pata_it821x: Fix regression/corruptor
Whoever did the PCI revision patch slipped up on the it821x, and I
didn't spot this at the time either.  They moved the check for the
errata from the 0x10 revision to 0x11.  Put it back

This one is important for 2.6.23 final as in some cases bad things will
occur if 0x10 revision boards don't get the fixups.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-08-23 21:32:54 -07:00
Alexey Dobriyan
deec595047 lguest should depend on CONFIG_FUTEX
It uses get_futex_key().

Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-08-23 21:23:33 -07:00
Mauro Carvalho Chehab
04b35abef7 V4L/DVB (6070): Fix a warning at dvb_net
static function dvb_net_sec declares input arg "pkt" as u8. However, the
same argument at dvb_net_sec_callback is defined as "const u8". When
calling dvb_net_sec, this is casted as just "u8".

gcc 4.2.1 generates a warning about that:

  CC [M]  drivers/media/dvb/dvb-core/dvb_net.o
drivers/media/dvb/dvb-core/dvb_net.c: In function "dvb_net_sec_callback":
drivers/media/dvb/dvb-core/dvb_net.c:905: warning: passing argument 2 of
		"dvb_net_sec" discards qualifiers from pointer target type

Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-08-23 13:17:32 -03:00
Trent Piepho
6175e487e3 V4L/DVB (6042): b2c2-flexcop: fix Airstar HD5000 tuning regression
Git changeset 6bdcc6e6db dropped the
stand-alone lgh06xf module, whose functionality was absorbed into the
dvb-pll module. However, there was a minor difference between the code
in lgh06xf and dvb-pll, which caused a regression in b2c2-flexcop
devices using the LG-H06xF NIM.

dvb-pll will probe for the presence of an i2c pll chip by performing a
single byte read, the lgh06xf driver did not do this. Unfortunately, the
code in flexcop-i2c.c does not currently support 1 byte or 0 byte reads
as a probe.  Such probes with the current code will always fail.

In order to work around this problem, and restore proper functionality
of the Airstar HD5000 device, this hack was created to make the probe
appear to succeed.  The single byte read in dvb_pll_attach is the only
place where such a probe would ever occur, so this change is safe, and
will not affect any other devices.

Of course, if one knew how to actually perform the read operation, it
would be better to go that route.  In the meantime, however, we must
apply this workaround, in order to prevent the regression that causes
tuning to fail on the Airstar HD5000 ATSC device.

Thanks to Jarod Wilson, who had originally reported this regression, and
to Geoffrey Hausheer, whose original workaround patch led us to find the
actual cause of the problem.

Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Cc: Geoffrey Hausheer <inli3epy93n@phracturedblue.com>
Acked-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-08-23 13:17:32 -03:00
Mariusz Kozlowski
02881d9478 9p: fix bad error path in conversion routines
When buf_check_overflow() returns != 0 we will hit kfree(ERR_PTR(err))
and it will not be happy about it.

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
2007-08-23 10:25:05 -05:00
Eric Van Hensbergen
fbcb7599e4 9p: remove deprecated v9fs_fid_lookup_remove()
This patch removes the v9fs_fid_lookup_remove which is no longer used.

Based on original patch from Adrian Bunk <bunk@stusta.de> which
used #if 0 to isolate the code.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
2007-08-23 10:13:45 -05:00
Eric Van Hensbergen
27a2a5ff41 9p: update maintainers and documentation
Updates to the MAINTAINERS file and documentation for 9p to point to the
swik wiki versus the outdated sf.net page.  Also updated some email addresses
and added pointers to papers which better describe the implementation and
application of the Linux 9p client.

Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
2007-08-23 10:12:48 -05:00
Eric Van Hensbergen
1a3cac6c6d 9p: fix use after free
On 7/22/07, Adrian Bunk <bunk@stusta.de> wrote:
     The Coverity checker spotted the following use-after-free
     in net/9p/mux.c:

     <--  snip  -->

     ...
     struct p9_conn *p9_conn_create(struct p9_transport *trans, int msize,
                                         unsigned char *extended)
     {
     ...
             if (!m->tagpool) {
                     kfree(m);
                     return ERR_PTR(PTR_ERR(m->tagpool));
             }
     ...

     <--  snip  -->

Also spotted was a leak of the same structure further down in the function.

Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
2007-08-23 10:12:48 -05:00
Ingo Molnar
505c0efd58 sched: tweak the sched_runtime_limit tunable
Michael Gerdau reported reniced task CPU usage weirdnesses.
Such symptoms can be caused by limit underruns so double the
sched_runtime_limit.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
2007-08-23 15:18:02 +02:00
Suresh Siddha
f549da848e sched: skip updating rq's next_balance under null SD
Was playing with sched_smt_power_savings/sched_mc_power_savings and
found out that while the scheduler domains are reconstructed when sysfs
settings change, rebalance_domains() can get triggered with null domain
on other cpus, which is setting next_balance to jiffies + 60*HZ.
Resulting in no idle/busy balancing for 60 seconds.

Fix this.

Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2007-08-23 15:18:02 +02:00
Suresh Siddha
f8700df7c4 sched: fix broken SMT/MC optimizations
On a four package system with HT - HT load balancing optimizations were
broken.  For example, if two tasks end up running on two logical threads
of one of the packages, scheduler is not able to pull one of the tasks
to a completely idle package.

In this scenario, for nice-0 tasks, imbalance calculated by scheduler
will be 512 and find_busiest_queue() will return 0 (as each cpu's load
is 1024 > imbalance and has only one task running).

Similarly MC scheduler optimizations also get fixed with this patch.

[ mingo@elte.hu: restored fair balancing by increasing the fuzz and
                 adding it back to the power decision, without the /2
                 factor. ]

Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2007-08-23 15:18:02 +02:00
Christian Borntraeger
efe567fc82 sched: accounting regression since rc1
Fix the accounting regression for CONFIG_VIRT_CPU_ACCOUNTING.  It
reverts parts of commit b27f03d4bd by
converting fs/proc/array.c back to cputime_t.  The new functions
task_utime and task_stime now return cputime_t instead of clock_t.  If
CONFIG_VIRT_CPU_ACCOUTING is set, task->utime and task->stime are
returned directly instead of using sum_exec_runtime.

Patch is tested on s390x with and without VIRT_CPU_ACCOUTING as well as
on i386.

[ mingo@elte.hu: cleanups, comments. ]

Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2007-08-23 15:18:02 +02:00
Eric W. Biederman
c57baf1e1e sched: fix sysctl directory permissions
There are two remaining gotchas:

- The directories have impossible permissions (writeable).

- The ctl_name for the kernel directory is inconsistent with
  everything else.  It should be CTL_KERN.

Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2007-08-23 15:18:02 +02:00
Ingo Molnar
2aa44d0567 sched: sched_clock_idle_[sleep|wakeup]_event()
construct a more or less wall-clock time out of sched_clock(), by
using ACPI-idle's existing knowledge about how much time we spent
idling. This allows the rq clock to work around TSC-stops-in-C2,
TSC-gets-corrupted-in-C3 type of problems.

( Besides the scheduler's statistics this also benefits blktrace and
  printk-timestamps as well. )

Furthermore, the precise before-C2/C3-sleep and after-C2/C3-wakeup
callbacks allow the scheduler to get out the most of the period where
the CPU has a reliable TSC. This results in slightly more precise
task statistics.

the ACPI bits were acked by Len.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Len Brown <len.brown@intel.com>
2007-08-23 15:18:02 +02:00
Tejun Heo
b54eebd673 libata: don't check n_sectors during revalidation if zero
If the initial configuration fails early, n_sectors is left at zero.
Checking against it during revalidation makes retried configuration
fail due to n_sectors mismatch.  Ignore zero n_sectors during
revalidation.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:34:05 -04:00
Alan Cox
9edbdbea00 pata_via: Add Arima W730-K8 and other rebadgings
More cable funnies

Signed-off-by: Alan Cox <alan@redhat.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:32:07 -04:00
Alan Cox
4f2d47cfdd pata_sis: Add the FSC Amilo and friends
More short cables

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:32:07 -04:00
Mikael Pettersson
78c4af0b43 pata_pdc2027x: PLL detection fixes
Previously I reported that the pata_pdc2027x PLL detection changes
in kernel 2.6.22 broke the driver on my PowerMac:

>pata_pdc2027x: Invalid PLL input clock 1691742kHz, give up!

This is followed by a number of errors and speed reduction
steps on the affected ports.

There are two bugs in pata_pdc2027x's PLL detection code:

1. The PLL counter's start value is read before the chip is
   put in "test mode". Outside of test mode the counter is
   halted, and on the PowerMac the counter is zero because
   the chip hasn't been initialised by its BIOS.

   The fix is to move the read of the start value to after
   test mode is started, but before the mdelay() in test mode.
   This also improves the precision of the PLL detection.

2. The code to compute the number of PLL decrements during the
   mdelay() in test mode fails to consider that the PLL counter
   only is 30 bits wide. If there is a wraparound, it will compute
   an incorrect and much too large value. On the PowerMac, the
   start count is zero, the end count is a large 30-bit value, so
   wraparound occurs and an out of bounds PLL clock is detected.

   The fix is to mask the (start - end) computation to 30 bits.

While debugging this I also noticed that pdc_read_counter()
reads the two halves of the 30-bit PLL counter as 16-bit values,
and then combines them as if the halves only are 15 bits wide.
To avoid confusion, the halves should be read as 15-bit values.

This patch implements all three changes. It fixes the PLL detection
failure on my PowerMac, and doesn't cause any regressions on an x86
with an identical card.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:32:07 -04:00
Tejun Heo
8270bec400 libata: fix n_sectors failure handling during revalidation
If revalidation fails because device has different n_sectors after
configuration the original n_sectors should be restored before failing
revalidation.  Without this fix, n_sectors difference will incorrectly
and silently pass revalidation when revalidation is retried.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:23:14 -04:00
Pierre Ossman
b67ac3f339 sdhci: tell which spurious interrupt we got
When we get unexpected interrupts, also print which interrupt it was.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-23 06:31:07 +02:00
Pierre Ossman
e538fbe83e sdhci: handle data interrupts during command
It is fully legal for a controller to start issuing data related
interrupts before it has signalled that the command has completed.
Make sure the driver actually can handle this.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-23 06:30:53 +02:00
David Vrabel
03f8590d90 mmc: ignore bad max block size in sdhci
Some SDHC cards report an invalid maximum block size, in these cases
assume they support block sizes up to 512 bytes instead of returning
an error.

Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-23 06:27:50 +02:00
Pierre Ossman
2b06197340 sdhci: be more cautious about block count register
The block count register shouldn't be trusted for single block transfers,
so avoid using it completely when calculating transferred bytes.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-23 06:27:44 +02:00
Mariusz Kozlowski
be760a9de8 drivers/mmc/core/host.c: kmalloc + memset conversion to kzalloc
drivers/mmc/core/host.c | 3509 -> 3457 (-52 bytes)
 drivers/mmc/core/host.o | 92400 -> 92136 (-264 bytes)

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-23 06:26:31 +02:00
Mariusz Kozlowski
733cb1e440 drivers/mmc/core/bus.c: kmalloc + memset conversion to kzalloc
drivers/mmc/core/bus.c | 5663 -> 5619 (-44 bytes)
 drivers/mmc/core/bus.o | 70899 -> 70731 (-168 bytes)

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-23 06:26:26 +02:00
Mel Gorman
b377fd3982 Apply memory policies to top two highest zones when highest zone is ZONE_MOVABLE
The NUMA layer only supports NUMA policies for the highest zone.  When
ZONE_MOVABLE is configured with kernelcore=, the the highest zone becomes
ZONE_MOVABLE.  The result is that policies are only applied to allocations
like anonymous pages and page cache allocated from ZONE_MOVABLE when the
zone is used.

This patch applies policies to the two highest zones when the highest zone
is ZONE_MOVABLE.  As ZONE_MOVABLE consists of pages from the highest "real"
zone, it's always functionally equivalent.

The patch has been tested on a variety of machines both NUMA and non-NUMA
covering x86, x86_64 and ppc64.  No abnormal results were seen in
kernbench, tbench, dbench or hackbench.  It passes regression tests from
the numactl package with and without kernelcore= once numactl tests are
patched to wait for vmstat counters to update.

akpm: this is the nasty hack to fix NUMA mempolicies in the presence of
ZONE_MOVABLE and kernelcore= in 2.6.23.  Christoph says "For .24 either merge
the mobility or get the other solution that Mel is working on.  That solution
would only use a single zonelist per node and filter on the fly.  That may
help performance and also help to make memory policies work better."

Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Acked-by:  Lee Schermerhorn <lee.schermerhorn@hp.com>
Tested-by:  Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: Christoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-08-22 19:52:47 -07:00
Yoichi Yuasa
8e92f21ba3 au1100fb: move au1100fb_fb_blank() beforce au1100fb_setmode()
au1100fb_fb_blank() should come before au1100fb_setmode().

drivers/video/au1100fb.c: In function 'au1100fb_setmode':
drivers/video/au1100fb.c:211: error: implicit declaration of function 'au1100fb_fb_blank'

Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-08-22 19:52:47 -07:00