Commit Graph

1108 Commits

Author SHA1 Message Date
Tejun Heo
f8ab6d8e15 ata_generic: unindent loop in generic_set_mode()
Unindent loop body in generic_set_mode().  This is to ease future
change.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:11 -05:00
Jeff Garzik
e39eec13ff [libata] Build fix WRT ata_is_xxx() new API introduction
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-01-23 05:24:11 -05:00
Tejun Heo
76326ac1ac libata: implement fast speed down for unverified data transfer mode
It's very likely that the configured data transfer mode is the wrong
one if device fails data transfers right after initial data transfer
mode configuration (including NCQ on/off and xfermode).  libata EH
needs to speed down fast before upper layers give up on probing.

This patch implement fast speed down rules to handle such cases
better.  Error occured while data transfer hasn't been verified
trigger fast back-to-back speed down actions until data transfer
works.

This change will make cable mis-detection and other initial
configuration problems corrected before partition scanning code gives
up.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:11 -05:00
Tejun Heo
00115e0f5b libata: implement ATA_DFLAG_DUBIOUS_XFER
ATA_DFLAG_DUBIOUS_XFER is set whenever data transfer speed or method
changes and gets cleared when data transfer command succeeds in the
newly configured transfer mode.

This will be used to improve speed down logic.

Signed-off-by: Tejun Heo <htejun@gmail.com<
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:11 -05:00
Tejun Heo
663f99b86a libata: adjust speed down rules
Speed down rules were too conservative.  Adjust them a bit.

* More than 10 timeouts can't happen in 5 minutes as command timeout
  is 30secs.  Lower the limit for rule #1 to 6.

* 10 timeouts is too high for rule #3 too.  Lower it to 6.

* SATAPI can benefit from falling back to PIO too.  Allow SATAPI
  devices to fall back to PIO.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:11 -05:00
Tejun Heo
3884f7b0a8 libata: clean up EH speed down implementation
Clean up EH speed down implementation.

* is_io boolean variable is replaced eflags.  is_io is ATA_EFLAG_IS_IO.

* Error categories now have names.

* Better comments.

* Reorder 5min and 10min rules in ata_eh_speed_down_verdict()

* Use local variable @link to cache @dev->link in ata_eh_speed_down()

These changes are to improve readability and ease further changes.
This patch doesn't introduce any behavior change.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:10 -05:00
Tejun Heo
6f1d1e3a03 libata: move ata_set_mode() to libata-eh.c
Move ata_set_mode() to libata-eh.c.  ata_set_mode() is surely an EH
action and will be more tightly coupled with the rest of error
handling.  Move it to libata-eh.c.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:10 -05:00
Tejun Heo
02c05a27e8 libata: factor out ata_eh_schedule_probe()
Factor out ata_eh_schedule_probe() from ata_eh_handle_dev_fail() and
ata_eh_recover().  This is to improve maintainability and make future
changes easier.

In the previous revision, ata_dev_enabled() test was accidentally
dropped while factoring out.  This problem was spotted by Bartlomiej.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:10 -05:00
Tejun Heo
405e66b387 libata: implement protocol tests
Implement protocol tests - ata_is_atapi(), ata_is_nodata(),
ata_is_pio(), ata_is_dma(), ata_is_ncq() and ata_is_data() and use
them to replace is_atapi_taskfile() and hard coded protocol tests.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:10 -05:00
Jeff Garzik
11b7becca9 libata: checkpatch fixes
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-01-23 05:24:10 -05:00
Tejun Heo
49f2909039 ahci: update PCS programming
For intel ones, ahci unconditionally OR'd 0xf to PCS.  This isn't
correct for the following cases.

* ich6/7m's which only implement P0 and P2 (0xf works fine tho)

* ich8/9's which have six ports and needs 0x3f to enable all ports

This patch updates PCS programming such that...

* port_map determined by ahci_save_initial_config() is OR'd instead of 0xf

* PCS is updated only if necessary (there are turned off enable bits)

port_map is determined from PORTS_IMPL PCI register which is
implemented as write or write-once register.  If the register isn't
programmed, ahci automatically generates it from number of ports,
which is good enough for PCS programming.  ICH6/7M are probably the
only ones where non-contiguous enable bits are necessary && PORTS_IMPL
isn't programmed properly but they're proven to work reliably with 0xf
anyway.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:10 -05:00
Alan Cox
51dbd49061 pata_ninja32: Cardbus ATA initial support
Lots of work needed to bring it up to scratch but it does work so you can
now use the card. That makes it at least useful, especially as the other
cardbus cards are usually INIC162x which aren't yet supported well.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:10 -05:00
Alan Cox
76548eda8c libata-sff: tf_load
Jeff said he preferred that the SFF tf_load followed the spec and we
documented that anyone who needed different overrode it, rather than it
using the ->check_status methods. No driver relies on the current behaviour.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:09 -05:00
Alan Cox
b9f8ab2daf libata: IORDY handling
I believe this version meets all Sergei's objections

Correct the logic for when we issue a set features for transfer mode

- If the device has IORDY and the controller has IORDY - set the mode
- If the device has IORDY and the controller does not - turn IORDY off
- If neither has IORDY do nothing

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:09 -05:00
Shaohua Li
bd3adca52b libata-acpi: add ACPI _PSx method
ACPI spec (ver 3.0a, p289) requires IDE power on/off executes ACPI _PSx
methods. As recently most PATA drivers use libata, this patch adds _PSx
method support in libata. ACPI spec doesn't mention if SATA requires the
same _PSx method.

Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-01-23 05:24:09 -05:00
Alan Cox
ae8d4ee7ff libata: Disable ATA8-ACS proposed Trusted Computing features by default
Historically word 48 in the identify data was used to mean 32bit I/O
was supported for VLB IDE etc. ATA8 reassigns this word to the Trusted
Computing Group, where it is used for TCG features. This means that
an ATA8 TCG drive is going to trigger 32bit I/O on some systems which
will be funny.

Anyway we need to sort this out ready for ATA8 so:
- Reorder the ata.h header a bit so the ata_version function occurs early
  in it
- Make dword_io check the ATA version
- Add an ATA8 version checking TCG presence test

While we are at it the current drafts have a flaw where it may not be
possible to disable TCG features at boot (and opt out of the trusted
model) as TCG intends because it relies on presence of a different
optional feature (DCS). Handle this in software by refusing the TCG
commands if libata.allow_tpm is not set. (We must make it possible
as some environments such as proprietary VDR devices will doubtless
want to use it to lock up content)

Finally as with CPRM print a warning so that the user knows they may
not be able to full access and use the device.

Signed-off-by: Alan Cox <alan@redhat.com>
2008-01-23 05:24:09 -05:00
Peter Schwenke
ffe188dd83 ata_piix: Add Toshiba Satellite R20 and Tecra M6 to broken suspend list.
Add Toshiba Satellite R20 and Tecra M6 to broken suspend list.  Matt
Piermarini reported and provided the M6 patch.  This is from OSDL bug 7780.

Signed-off-by: Peter Schwenke <peter@bluetoad.com.au>
Cc: Matt Piermarini <mattpiermarini@yahoo.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:23:15 -05:00
Alan Cox
aa8f2371c5 pata_pdc202xx_old: Fix crashes with ATAPI
The PDC202xx older devices do not support ATAPI DMA via the usual
interfaces. What documentation I have isn't sufficient to support DMA and
it isn't clear if the Windows drivers do this or it is possible at all.
(Neither do the drivers/ide old drivers)

So turn it ATAPI DMA off, these are disk optimised controllers.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-01-19 21:29:39 -08:00
Andrew Morton
0f7577434b [libata] core checkpatch fix
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-15 15:59:18 -05:00
Andrew Morton
ed722d3d3e [libata] pata_bf54x: checkpatch fixes
WARNING: line over 80 characters
#36: FILE: drivers/ata/pata_bf54x.c:1512:
+	while (bfin_port_info[board_idx].udma_mask>0 && udma_fsclk[udma_mode] > fsclk) {

ERROR: need spaces around that '>' (ctx:VxV)
#36: FILE: drivers/ata/pata_bf54x.c:1512:
+	while (bfin_port_info[board_idx].udma_mask>0 && udma_fsclk[udma_mode] > fsclk) {
 	                                          ^

total: 1 errors, 1 warnings, 19 lines checked

Your patch has style problems, please review.  If any of these errors
are false positives report them to the maintainer, see
CHECKPATCH in MAINTAINERS.

Please run checkpatch prior to sending patches

Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: sonic zhang <sonic.adi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-15 15:58:59 -05:00
Al Viro
b50e56d81e libata fixes for sparse-found problems
In pata_legacy and pata_winbond we've got bugs - cpu_to_le16() instead
of cpu_to_le32().  Fortunately, both affected suckers are VLB, thus
l-e-only, so we might get away with that unless we hit it with slop == 3
(hadn't checked if playing with badly aligned sg could trigger that).
Still buggy...  Moreover, pata_legacy, pata_winbond and pata_qdi forgot to
initialize pad on the write side of 32bit case in their ->data_xfer().
Hopefully the hardware does't care, but still, sending uninitialized
data to it...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-15 15:58:36 -05:00
Tejun Heo
d8cf5389bd libata: relocate sdev->manage_start_stop configuration
After 9b8e8de7, manage_start_stop configuration depends on valid ATA
device.  Move it into ata_scsi_dev_config().  This was detected by the
coverity checker.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-14 21:11:02 -05:00
Tejun Heo
c2e14f1112 sata_sil24: freeze on non-dev errors reported via CERR
CERR reports errors detected during executing a command.  This doesn't
mean the error is tied to the command and can be recovered by just
issuing it again.  Many of the errors are fatal port-wide connditions
including HSM violation, host bus error and ATA bus error and require
freezing and port reset.

The freezing part wasn't implemented previously.  This used to be okay
because port resets were scheduled anyway and EH eventually resets and
recovers the port.  With PMP support added, this is no longer true.
The error condition and recover actions are attributed to the fan-out
port and the host port condition isn't properly recovered leading to
EH failures.

This patch makes CERR errors which require resets to freeze the port.
This will force host port reset and proper recovery.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Andrew Ryder <tireman@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-14 21:11:02 -05:00
Tejun Heo
7293fa8fb7 sata_sil24: fix stupid typo
Fix stupid typo.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-14 21:11:01 -05:00
Tejun Heo
25f98131a2 ata_piix: ignore ATA_DMA_ERR on vmware ich4
VMware ich4 emulation incorrectly sets DMA_ERR on TF error.  Ignore
it.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-14 21:11:01 -05:00
James Bottomley
465ff3185e [SCSI] relax scsi dma alignment
This patch relaxes the default SCSI DMA alignment from 512 bytes to 4
bytes.  I remember from previous discussions that usb and firewire have
sector size alignment requirements, so I upped their alignments in the
respective slave allocs.

The reason for doing this is so that we don't get such a huge amount of
copy overhead in bio_copy_user() for udev.  (basically all inquiries it
issues can now be directly mapped).

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 18:29:22 -06:00
Ondrej Zary
9b8e8de7e5 libata and starting/stopping ATAPI floppy devices
Prevent libata from starting/stopping non-ATA devices (like ATAPI floppy
drives) as they don't seem to like it:

sd 1:0:1:0: [sdb] Starting disk
ata2.01: configured for PIO2
sd 1:0:1:0: [sdb] Result: hostbyte=0x00 driverbyte=0x08
sd 1:0:1:0: [sdb] Sense Key : 0x2 [current]
sd 1:0:1:0: [sdb] ASC=0x3a ASCQ=0x0

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-01-10 17:13:19 -05:00
Gwendal Grignou
13cc546be3 sata_sil24: prevent hba lockup when pass-through ATA commands are used
Fix commands timeout with Sil3124/3132 based HBA when pass-through ATA
commands [where ATA_QCFLAG_RESULT_TF is set] are used while other
commands are active on other devices connected to the same port with a
Port Multiplier.  Due to a hardware bug, these commands must be sent
alone, like ATAPI commands.

Signed-off-by: Gwendal Grignou <gwendal@google.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10 16:54:01 -05:00
Tejun Heo
4ccd3329a2 libata: don't normalize UNKNOWN to NONE after reset
After non-classifying reset, ehc->classes[] could contain
ATA_DEV_UNKNOWN which used to be normalized to ATA_DEV_NONE for
consistency.  However, this causes unfortunate side effect for drivers
which have non-classifying hardresets (e.g. sata_nv) by making
hardreset report ATA_DEV_NONE for non-classifying resets and thus
makes EH believe that the port is unoccupied and recovery can be
skipped.  The end result is that after a device is swapped with
another one, the new device isn't attached after the old one is
detached.

This patch makes ata_eh_reset() not normalize UNKNOWN to NONE after
non-classifying resets.  This fixes the above problem.  As UNKNOWN and
NONE are handled differently by only EH hotplug logic, this doesn't
cause other behavior changes.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10 16:53:22 -05:00
Tejun Heo
2695e36616 libata-pmp: propagate timeout to host link
Timeout on downstream command may indicate transmission problem on
host link.  Propagate timeouts to host link.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10 16:53:16 -05:00
Tejun Heo
8048307dbc libata-pmp: 4726 hates SRST
4726 hates SRST even on non-config ports.  Don't use it.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10 16:53:12 -05:00
Rod Whitby
af18374804 pata_ixp4xx_cf: fix compilation introduced by ata_port_desc() conversion
Fixes a compilation error caused by ata_port_desc() conversion
(cbcdd87593).

Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10 16:53:10 -05:00
Alan Cox
36906d9bea pata_pdc202xx_old: Further fixups
Turns out distros always enabled burst mode and it is pretty essential so
do the same. Also sort out the post DMA mode restore properly.

My 20263 card now seems happy but needs some four drive tests done yet
(when I've persuaded the kernel not to hang in the edd boot code if I
plug them in ..)

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10 16:52:53 -05:00
Alan Cox
277d72a374 libata-sff: PCI IRQ handling fix
It is legitimate (although annoying and silly) for a PCI IDE controller
not to be assigned an interrupt and to be polled. The libata-sff code
should therefore not try and request IRQ 0 in this case.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10 16:52:51 -05:00
Tejun Heo
b14dabcdb6 sata_qstor: use hardreset instead of softreset
During conversion to new EH, sata_qstor was accidentaly changed to use
softreset, which is buggy on this chip, instead of hardreset.  This
patch updates sata_qstor such that it uses hardreset again.

This fixes bugzilla bug 9631.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10 16:52:41 -05:00
Alan Cox
f941b168a4 pata_hpt37x: Fix HPT374 detection
Bug #9261

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-12-19 14:29:01 -08:00
Tejun Heo
140b5e5911 libata: fix ATAPI draining
With ATAPI transfer chunk size properly programmed, libata PIO HSM
should be able to handle full spurious data chunks.  Also, it's a good
idea to suppress trailing data warning for misc ATAPI commands as
there can be many of them per command - for example, if the chunk size
is 16 and the drive tries to transfer 510 bytes, there can be 31
trailing data messages.

This patch makes the following updates to libata ATAPI PIO HSM
implementation.

* Make it drain full spurious chunks.

* Suppress trailing data warning message for misc commands.

* Put limit on how many bytes can be drained.

* If odd, round up consumed bytes and the number of bytes to be
  drained.  This gets the number of bytes to drain right for drivers
  which do 16bit PIO.

This patch is partial backport of improve-ATAPI-data-xfer patchset
pending for #upstream.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-17 20:43:28 -05:00
Tejun Heo
f2dfc1a12b libata: update atapi_eh_request_sense() such that lbam/lbah contains buffer size
While updating lbam/h for ATAPI commands, atapi_eh_request_sense() was
left out.  Update it.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-17 20:33:15 -05:00
Tejun Heo
3264a8d8f9 libata-acpi: implement _GTF command filtering
Implement _GTF command filtering which can be controlled by
libata.acpi_filter kernel parameter.  Currently SETXFER and LOCK
commands are filtered.

libata configures transfer mode by itself and _GTF SETXFER commands
can potentially disrupt device configuration.  _GTM/_STM mechanism
can't handle hotplugging too well and when _GTF is executed,
controller is in PIO0 rather than the mode _STM configured.

Note that detecting SET MAX LOCK requires looking at the previous
command.  This adds a bit to code complexity.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-17 20:33:15 -05:00
Tejun Heo
0e8634bf8e libata-acpi: improve _GTF execution error handling and reporting
As _GTF commands can't transfer data, device error never signals
transfer error.  It indicates that the device vetoed the operation, so
it's meaningless to retry.

This patch makes libata-acpi to report and continue on device errors
when executing _GTF commands.  Also commands rejected by device don't
contribute to the number of _GTF commands executed.

While at it, update _GTF execution reporting such that all successful
commands are logged at KERN_DEBUG and rename taskfile_load_raw() to
ata_acpi_run_tf() for consistency.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-17 20:33:15 -05:00
Tejun Heo
66fa7f2158 libata-acpi: improve ACPI disabling
* If _GTF evalution fails, it's pointless to retry.  If nothing else
  is wrong, just ignore the error.

* After disabling ACPI, return success iff the number of executed _GTF
  command equals zero.  Otherwise, tell EH to retry.  This change
  fixes bogus 1 return bug where ata_acpi_on_devcfg() expects the
  caller to reload IDENTIFY data and continue but the caller
  interprets it as an error.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-17 20:33:14 -05:00
Tejun Heo
398e07826b libata-acpi: implement dev->gtf_cache and evaluate _GTF right after _STM during resume
On certain implementations, _GTF evaluation depends on preceding _STM
and both can be pretty picky about the configuration.  Using _GTM
result cached during controller initialization satisfies the most
neurotic _STM implementation.  However, libata evaluates _GTF after
reset during device configuration and the hardware state can be
different from what _GTF expects and can cause evaluation failure.

This patch adds dev->gtf_cache and updates ata_dev_get_GTF() such that
it uses the cached value if available.  Cache is cleared with a call
to ata_acpi_clear_gtf().

Because for SATA ACPI nodes _GTF must be evaluated after _SDD which
can't be done till IDENTIFY is complete, _GTF caching from
ata_acpi_on_resume() is used only for IDE ACPI nodes.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-17 20:33:14 -05:00
Tejun Heo
c05e6ff035 libata-acpi: implement and use ata_acpi_init_gtm()
_GTM fetches currently configured transfer mode while _STM configures
controller according to _GTM parameter and prepares transfer mode
configuration TFs for _GTF.  In many cases _GTM and _STM
implementations are quite brittle and can't cope with configuration
changed by libata.

libata does not depend on ATA ACPI to configure devices.  The only
reason libata performs _GTM and _STM are to make _GTF evaluation
succeed and libata also doesn't care about how _GTF TFs configure
transfer mode.  It overrides that configuration anyway, so from
libata's POV, it doesn't matter what value is feeded to _STM as long
as evaluation succeeds for _STM and following _GTF.

This patch adds dev->__acpi_init_gtm and store initial _GTM values on
host initialization before modified by reset and mode configuration.
If the field is valid, ata_acpi_init_gtm() returns pointer to the
saved _GTM structure; otherwise, NULL.

This saved value is used for _STM during resume and peek at
BIOS/firmware programmed initial timing for later use.  The accessor
is there to make building w/o ACPI easy as dev->__acpi_init doesn't
exist if ACPI is not enabled.

On driver detach, the initial BIOS configuration is restored by
executing _STM with the initial _GTM values such that the next driver
can also use the initial BIOS configured values.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-17 20:33:14 -05:00
Tejun Heo
562f0c2d77 libata-acpi: add new hooks ata_acpi_dissociate() and ata_acpi_on_disable()
Add two hooks - ata_acpi_dissociate() which is called during driver
detach after the whole host is shutdown and ata_acpi_on_disable()
which is called when a device is disabled.

Signed-off-by: Tejun heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-17 20:33:12 -05:00
Tejun Heo
7f9ad9b8b9 libata: ata_dev_disable() should be called from EH context
ata_port_detach() calls ata_dev_disable() with host lock held but
ata_dev_disable() should be called from EH context.  ata_port_detach()
steals EH context by setting ATA_PFLAG_UNLOADAING and flushing EH.
Drop locking around ata_dev_disable() and note that ata_port_detach()
owns EH context at that point.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-17 20:33:12 -05:00
Tejun Heo
0d02f0b22b libata-acpi: adjust constness in ata_acpi_gtm/stm() parameters
* No internal function uses const ata_port.  Drop const from @ap.

* Make ata_acpi_stm() copy @stm before using it and change @stm to
  const.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-17 20:33:12 -05:00
Mark Lord
4e5200334e sata_mv: improve warnings about Highpoint RocketRAID 23xx cards
Improve the existing boot/load time warnings from sata_mv
for Highpoint RocketRAID 23xx cards, based on new knowledge
about where the BIOS likes to overwrite sectors with metadata.

Harmless to us, but very useful for end users.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-17 20:33:12 -05:00
Tejun Heo
e41bd3e854 libata: add ST3160023AS / 3.42 to NCQ blacklist
Like ST380817AS / 3.42, ST3160023AS / 3.42 times out commands if NCQ
is used.  Blacklist it.  This is reported by Matheus Izvekov in the
following thread.

  http://thread.gmane.org/gmane.linux.ide/24202

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Matheus Izvekov <mizvekov@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-17 20:33:12 -05:00
Tejun Heo
f7fe7ad4bc libata: clear link->eh_info.serror from ata_std_postreset()
link->eh_info.serror is used to cache SError for controllers which
need it cleared from interrupt handler to clear IRQ.  It also should
be cleared after reset just like SError itself.

Make ata_std_postreset() clear link->eh_info.serror too and update
sata_sil such that it doesn't care about bookkeeping the value.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-17 20:33:11 -05:00
Tejun Heo
8cf32ac657 sata_sil: fix spurious IRQ handling
Interestingly, sata_sil raises spurious interrupts if it's coupled
with Sil SATA_PATA bridge.  Currently, sata_sil interrupt handler is
strict about spurious interrupts and freezes the port when it occurs.
This patch makes it more forgiving.

* On SATA PHY event interrupt, serror value is checked to see whether
  it really is PHYRDY CHG event.  If not, SATA PHY event interrupt is
  ignored.

* If ATA interrupt occurs while no command is in progress, it's
  cleared and ignored.

This fixes bugzilla bug 9505.

  http://bugzilla.kernel.org/show_bug.cgi?id=9505

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-17 20:33:11 -05:00
Tejun Heo
459ad68893 libata: kill spurious NCQ completion detection
Spurious NCQ completion detection implemented in ahci was incorrect.
On AHCI receving and processing FISes and raising interrupts are not
interlocked and spurious interrupts are expected.

For example, if an interrupt occurs while interrupt handler is running
and the running interrupt handler handles the event the new IRQ
indicated, after IRQ handler finishes, it will be executed again
because IRQ pending bit is set by the new interrupt but there won't be
anything to process.

Please read the following message for more information.

  http://article.gmane.org/gmane.linux.ide/26012

This patch...

* Removes all spurious IRQ whining from ahci.  Spurious NCQ completion
  detection was completely wrong.  Spurious D2H Register FIS taught us
  that some early drives send spurious D2H Register FIS with I bit set
  while NCQ commands are in progress but none of recent drives does
  that and even the ones which show such behavior can do NCQ fine.

* Kills all NCQ blacklist entries which were added because of spurious
  NCQ completions.  I tracked down each commit and verified all
  removed ones are actually added because of spurious completions.

  WD740ADFD-00NLR1 wasn't deleted but moved upward because the drive
  not only had spurious NCQ completions but also is slow on sequential
  data transfers if NCQ is enabled.

  Maxtor 7V300F0 was added by 0e3dbc01d5
  from Alan Cox.  I can only find evidences that the drive only had
  troubles with spuruious completions by searching the mailing list.
  This entry needs to be verified and removed if it doesn't have other
  NCQ related problems.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-07 15:27:54 -05:00
Tejun Heo
c4f7792c02 ahci: don't attach if ICH6 is in combined mode
ICH6 R/Ms share PCI ID between piix and ahci modes and we've been
allowing ahci to attach regardless of how BIOS configured it.
However, enabling AHCI mode when the controller is in combined mode
can result in unexpected behavior.  Don't attach if the controller is
in combined mode.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Bill Nottingham <notting@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-07 15:27:54 -05:00
Peter Schwenke
d1aa690a7d ata_piix: add Toshiba Tecra M4 to broken suspend list
Add Toshiba Tecra M4 to broken suspend list.  This is from OSDL
bugzilla bug 7780.

Signed-off-by: Peter Schwenke <peter@bluetoad.com.au>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-07 15:27:54 -05:00
Tejun Heo
994056d7aa ahci: fix engine reset failed message
There isn't much point in reporting -EOPNOTSUPP as failure.  Also the
message was missing newline.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-07 15:27:53 -05:00
Bartlomiej Zolnierkiewicz
943547abdf pata_amd/pata_via: de-couple programming of PIO/MWDMA and UDMA timings
* Don't program UDMA timings when programming PIO or MWDMA modes.

  This has also a nice side-effect of fixing regression added by commit
  681c80b5d9 ("libata: correct handling of
  SRST reset sequences") (->set_piomode method for PIO0 is called before
  ->cable_detect method which checks UDMA timings to get the cable type).

* Bump driver version.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Tested-by: "Thomas Lindroth" <thomas.lindroth@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-04 14:11:36 -05:00
peerchen
6ba8695870 ahci: add the Device IDs of MCP79 AHCI controller to ahci.c
Add the device IDs of legacy mode of MCP79 AHCI controller to ahci.c

Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-04 14:10:14 -05:00
Mark Lord
306b30f74d sata_mv: Warn about HPT RocketRAID BIOS treatment of "Legacy" drives
The Highpoint RocketRAID boards using Marvell 7042 chips
overwrite the 9th sector of attached drives at boot time,
when those drives are configured as "Legacy" (the default)
in the HighPoint BIOS.

This kills GRUB, and probably other stuff.
But it all happens *before* Linux is even loaded.

So, for now we'll log a WARNING when such boards are detected,
and advise users to configure BIOS "JBOD" volumes instead,
which don't appear to suffer from this problem.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-12-04 14:07:52 -05:00
Robert Hancock
3f3debdbfb sata_nv: don't use legacy DMA in ADMA mode (v3)
We need to run any DMA command with result taskfile requested in ADMA mode
when the port is in ADMA mode, otherwise it may try to use the legacy DMA engine
in ADMA mode which is not allowed. Enforce this with BUG_ON() since data
corruption could potentially result if this happened. Also, fail any attempt to
try and issue NCQ commands with result taskfile requested, since the hardware
doesn't allow this.

Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-04 14:01:18 -05:00
Mark Lord
02a121da5a sata_mv: Fix broken Marvell 7042 support.
sata_mv:  Fix broken Marvell 7042 support.

The Marvell 7042 chip is more or less the same as the 6042 internally,
but sports a PCIe bus.  Despite having identical SATA cores, the 7042
does differ from its PCI bus counterparts in placment and layout of
certain bus related registers.

This patch fixes sata_mv to distinguish between the PCI bus registers
of earlier chips, and the PCIe bus registers of the 7042.

Specifically, move the offsets and bit patterns for the
PCI/PCIe interrupt cause/mask registers into the struct mv_host_priv,
as these values differ between the 6xxx and 7xxx series chips.

This fixes the driver to not access reserved PCI addresses,
and prevents the lockups reported in linux-2.6.24 with 7042 boards.

Also add a new PCI ID for the Highpoint 2300 7042-based board
that I'm using for testing this stuff here.

Tested with Marvell 6081 + 7042 chips, on x86 & x86_64.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-01 17:44:10 -05:00
Alan Cox
0f9fe9b714 libata: Fix early use of port printk. (Was Re: ata4294967295: failed to start port (errno=-19))
On Fri, 30 Nov 2007 14:34:11 +0200 (EET)
Meelis Roos <mroos@linux.ee> wrote:

> > Can you stick a stack trace in at that point ? That would help diagnose
> > it a great deal quicker.
>
> Finally done - found out hard way that BUG() is too bad and
> dump_st5ack() suits me better.

Thanks. This should fix the real cause, and also allow for port start to
fail politely with -ENODEV.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-01 17:44:10 -05:00
Peter Schwenke
04d86d6fc0 ata_piix: add more toshiba laptops to broken suspend list
Add more toshiba laptops to broken suspend list.  This is from OSDL
bugzilla bug 7780.

tj: re-formatted patch and added description and SOB.

Signed-off-by: Peter Schwenke <peter@bluetoad.com.au>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-01 17:44:10 -05:00
Peter Missel
e9f3340673 libata: More IVB horkage from TSST
libata: Add more TSST (Samsung/Toshiba) IDE drives with broken
cable detection validation bits.

signed-off-by: Peter Missel (peter.missel@onlinehome.de)
Acked-by: Alan Cox <alan@redhat.com>

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-01 17:35:59 -05:00
Tejun Heo
abb6a88974 libata: report protocol and full CDB on error
Protocol and CDB allocation size field are important in determining
what went wrong with ATAPI commands.  Report them on failure.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-01 17:35:58 -05:00
Kristoffer Nyborg Gregertsen
1c20a493ca Several fixes for the AVR32 PATA driver
Several fixes for the AVR32 PATA driver:

* Updated to use new AVR32 SMC timing API. This removes the need for "magic"
constants in signal timing.

* Removed the ATA_FLAG_PIO_POLLING, the driver should use interrupts.

* Removed .port_disable and .irq_ack as these are no longer needed.

* Improved some comments.

Signed-off-by: Kristoffer Nyborg Gregertsen <kngregertsen@norway.atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-01 17:35:58 -05:00
Saeed Bishara
2d79ab8fd7 sata_mv: fix compilation error when enabling DEBUG
use sstatus instead status.

Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-01 17:35:58 -05:00
sonic zhang
f88c480dac Set proper ATA UDMA mode for bf548 according to system clock.
UDMA Mode - Frequency compatibility

UDMA5 - 100 MB/s   - SCLK  = 133 MHz
UDMA4 - 66 MB/s    - SCLK >=  80 MHz
UDMA3 - 44.4 MB/s  - SCLK >=  50 MHz
UDMA2 - 33 MB/s    - SCLK >=  40 MHz

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-01 17:35:58 -05:00
Tejun Heo
e190222d04 libata: bump transfer chunk size if it's odd
None of the drives I have follows what the standard says about
transfer chunk size.  Of the four SATA and six PATA ATAPI devices
tested, four ignore transfer chunk size completely and the ones which
honor it don't behave according to the spec when it's odd.

According to the spec, transfer chunk size can be odd if the amount of
data to transfer equals or is smaller than the chunk size and the
device can indicate the same odd number and transfer the whole thing
at one go with a pad byte appended.  However, in reality, none of the
drives I have does that.  They all indicate and transfer even number
of bytes one byte shorter than the chunk size first; then indicate and
transfer two bytes, which is clearly out of spec.

In addition to unnecessary second PIO data phase, this also creates a
weird problem when combined with SATA controllers which perform PIO
via DMA.  Some of these controllers use actualy number of bytes
received to update DMA pointer so chunks which are sized 4n + 2 makes
DMA pointer off by two bytes.  This causes data corruption and buffer
overruns.

This patch rounds nbytes up to the nearest even number such that ATAPI
devices don't split data transfer for the last odd byte.  This
shouldn't confuse controllers which depend on transfer chunk size as
devices will report the rounded-up number, actually transfer that much
and padding buffer is there to receive them.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-26 11:03:40 -05:00
sonic zhang
dc86f6d418 libata: Return proper ATA INT status in pata_bf54x driver
INT status can be OR.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-26 11:03:40 -05:00
Jeff Garzik
2541d0ca7e pata_ali: trim trailing whitespace (fix checkpatch complaints)
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-11-23 21:08:42 -05:00
Alan Cox
91e33d3109 pata_isapnp: Polled devices
If a card has no IRQ then pass no interrupt handler but allow polled
usage.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-23 19:33:27 -05:00
Alan Cox
22d5c760c8 pata_hpt37x: Fix cable detect bug spotted by Sergei
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-23 19:33:27 -05:00
Alan Cox
498222f323 pata_ali: Lots of problems still showing up with small ATAPI DMA
Hopefully there is a better long term solution but for now lets favour
reliability.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-23 19:33:27 -05:00
Alan Cox
8f59a13acc pata_ali: Add Mitac 8317 and derivatives
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-23 19:33:26 -05:00
Alan Cox
92c52c52e1 libata-core: List more documentation sources for reference
And next time I'll be able to find the ata tape spec easily...

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-23 19:33:26 -05:00
Alan Cox
c47a631f8b ata_piix: Invalid use of writel/readl with iomap
Should use ioread* as discussed previously

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-23 19:33:26 -05:00
Tejun Heo
93e2618e0c sata_sil24: fix sg table sizing
sil24 unnecessarily used LIBATA_MAX_PRD and ATAPI sg table was short
by one entry which might cause very obscure problems.  This patch
updates sg table sizing such that

* One full page is used for PRB + sg table.  On 4k page,
  this results in 253 sg's.

* Make ATAPI sg block properly sized.

* Make build fail if command block size doesn't equal PAGE_SIZE.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-23 19:23:55 -05:00
Tejun Heo
0706efd61e pata_jmicron: fix disabled port handling in jmicron_pre_reset()
There are two bugs in disabled port handling.

* test in PORT_PATA0 is reversed
* ->prereset should return -ENOENT for disabled ports not 0

The first bug makes the PATA channel considered disabled but the
second bug saves the day by returning 0.  The net result is that cable
is always left at ATA_CBL_UNKNOWN.  This results in false 80c
configuration and thus transfer errors.

This patch fixes both bugs.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-23 19:23:55 -05:00
Sergei Shtylyov
dd05c199cd pata_sil680: kill bogus reset code (take 2)
Since writing to two reserved bits ain't much of a housekeeping, I think it's
time we get rid of the custom error handler in this driver. ;-)

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-23 19:23:55 -05:00
Tejun Heo
a0ce9aca97 ata_piix: port enable for the first SATA controller of ICH8 is 0xf not 0x3
ICH8 and 9 use two SFF controllers to show 6 SATA ports.  The first
controllre hosts the first 4 ports while the second one hosts the last
2.  The PCS register of the first controller encompasses the first
four ports or all six ports depending on configuration while PCS of
the second controller controls the last two ports.  Using 0xf for the
first controller and 0x3 for the second controller always result in
the correct configuration.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2007-11-19 13:10:04 +09:00
Thomas Rohwer
8d8ef2fb93 ata_piix: only enable the first port on apple macbook pro
ICH8M on apple macbook pro occasionally locks up completely during PCS
initialization if ports other than the first one are enabled.  Add a
separate controller ID and only enable the first port.

tj: commit description added and patch updated to fit with the
    previous controller ID update.

Signed-off-by: Thomas Rohwer <tr@tng.de>
Signed-off-by: Tejun Heo <htejun@gmail.com>
2007-11-19 12:28:11 +09:00
Tejun Heo
00242ec876 ata_piix: reorganize controller IDs
Move piix_pata_mwdma to top, rename ich9_2port_sata to ich8_2port_sata
for consistency and use automatically incremented values instead of
assigning fixed values to ease adding new controller IDs.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2007-11-19 12:28:11 +09:00
Gabriel C
1f71d0672a pata_sis.c: Add Packard Bell EasyNote K5305 to laptops
With newer kernels HDD in my old laptop is limited to UDMA 33.
With this patch I get UDMA 100 again.

Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
2007-11-19 12:28:11 +09:00
Mark Lord
607126c2a2 libata-scsi: be tolerant of 12-byte ATAPI commands in 16-byte CDBs
Sebastian Kemper reported that issuing CD/DVD commands under libata is
not fully compatible with ide-scsi.  In particular, the
GPCMD_SET_STREAMING was being rejected at the host level in some
instances.

The reason is that libata-scsi insists upon the cmd_len field exactly
matching the SCSI opcode being issued, whereas ide-scsi tolerates
12-byte commands contained within a 16-byte (cmd_len) CDB.

There doesn't seem to be a good reason for us to not be compatible
there, so here is a patch to fix libata-scsi to permit SCSI opcodes so
long as they fit within whatever size CDB is provided.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
2007-11-19 12:28:11 +09:00
Albert Lee
f442cd86c1 libata: use ATA_HORKAGE_STUCK_ERR for ATAPI tape drives
Per Mark's comments, maybe all ATAPI tape drives need ATA_HORKAGE_STUCK_ERR.
This patch applys ATA_HORKAGE_STUCK_ERR for all ATAPI tape drives.

Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Tejun Heo <htejun@gmail.com>
2007-11-19 12:28:11 +09:00
Albert Lee
2d3b8eea7f libata: workaround DRQ=1 ERR=1 for ATAPI tape drives
After an error condition, some ATAPI tape drives set DRQ=1 together
with ERR=1 when asking the host to transfer the CDB of the next packet
command (i.e. request sense).  This patch, a revised version of
Alan/Mark's previous patch, adds ATA_HORKAGE_STUCK_ERR to workaround
the problem by ignoring the ERR bit and proceed sending the CDB.

Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Tejun Heo <htejun@gmail.com>
2007-11-19 12:28:11 +09:00
Adrian Bunk
21bef6dd2b libata: remove unused functions
This patch removes the following obsolete functions:
- libata-core.c: __sata_phy_reset()
- libata-core.c: sata_phy_reset()
- libata-eh.c: ata_qc_timeout()
- libata-eh.c: ata_eng_timeout()

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Tejun Heo <htejun@gmail.com>
2007-11-19 12:28:09 +09:00
Tejun Heo
de753e5e86 ata_piix: add SATELLITE U205 to broken suspend list
Satellite U205 has alternate product name where the satellite part is
all capatalized.  Add it to the blacklist.

This is reported by Ross Patterson in kernel bugzilla bug #7780.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Ross Patterson <me@rpatterson.net>
2007-11-19 12:28:09 +09:00
Matthew Garrett
037f6bb79f libata: Don't fail device revalidation for bad _GTF methods
Experience suggests that the _GTF method may be bad. We currently fail
device revalidation in that case, which seems excessive.

Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-10 00:31:27 -05:00
Tejun Heo
32ebbc0c0d libata: port and host should be stopped before hardware resources are released
Port / host stop calls used to be made from ata_host_release() which
is called after all hardware resources acquired after host allocation
are released.  This is wrong as port and host stop routines often
access the hardware.

Add separate devres for port / host stop which is invoked right after
IRQ is released but with all other hardware resources intact.  The
devres is added iff ->host_stop and/or ->port_stop exist.

This problem has been spotted by Mark Lord.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-08 13:08:42 -05:00
Tejun Heo
1974e20161 libata: skip 0xff polling for PATA controllers
In a presentation of true workmanship, pata_ali asserts IRQ
permanantly if the TF status register is read more than once when
there's no device attached to the port.

Avoid waiting polling for !0xff if it's PATA.  It's needed only for
some rare SATA devices anyway.

This problem is reported by Luca Tettamanti in bugzilla bug 9298.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Tested-By: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-08 13:08:41 -05:00
Paul Mundt
f7fc0ceb4d libata: pata_platform: Support polling-mode configuration.
Some SH boards (old R2D-1 boards) have generally not had working CF
under libata, due to both buswidth issues (handled by Aoi Shinkai
in 43f4b8c757), and buggy interrupt
controllers. For these sorts of boards simply disabling the IRQ and
polling ends up working fine.

This conditionalizes the IRQ resource for pata_platform and lets
platforms that want to use polling mode simply omit the resource
entirely.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-08 13:08:41 -05:00
Paul Mundt
3d46b2e2fa libata: Support PIO polling-only hosts.
By default ata_host_activate() expects a valid IRQ in order to
successfully register the host. This patch enables a special case
for registering polling-only hosts that either don't have IRQs
or have buggy IRQ generation (either in terms of handling or
sensing), which otherwise work fine.

Hosts that want to use polling mode can simply set ATA_FLAG_PIO_POLLING
and pass in an invalid IRQ.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-08 13:08:41 -05:00
Mark Lord
6004bda1cc libata sata_qstor conversion to new error handling (EH).
sata_qstor conversion to new error handling (EH).

Convert sata_qstor to use the newer libata EH mechanisms.
Based on earlier work by Jeff Garzik.

Signed-off-by:  Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-08 13:08:41 -05:00
Mark Lord
904c7bad99 libata sata_qstor workaround for spurious interrupts
sata_qstor workaround for spurious interrupts.

The qstor hardware generates spurious interrupts from time to time when
switching in and out of packet mode.  These eventually result in the
IRQ being disabled, which kills other devices sharing this IRQ with us.

This workaround isn't perfect, but it's about the best we can do for
this hardware.  Spurious interrupts will still happen, but won't be
logged as such, and therefore won't cause the IRQ to be inadvertently
disabled.

Signed-off-by:  Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-08 13:08:41 -05:00
Mark Lord
12ee7d3ceb libata sata_qstor nuke idle state
sata_qstor nuke idle state.

We're really only ever in one of two hardware states:  packet, or mmio.
Get rid of unnecessary "qs_state_idle" state.

Signed-off-by:  Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-08 13:08:41 -05:00
Fernando Luis Vázquez Cao
647c595dad nv_hardreset: update dangling reference to bugzilla entry
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-08 13:08:40 -05:00
Yann Chachkoff
62320e23c3 ata_piix: add SATELLITE PRO U200 to broken suspend list
Please warmly welcome the PRO variant of Satellite U200 to the broken
suspend list.

Original patch is from Yann Chachkoff.  Patch reformatted and
forwarded by Tejun Heo.

Signed-off-by: Yann Chachkoff <yann.chachkoff@myrealbox.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-08 13:08:40 -05:00
Alan Cox
6bbfd53d47 libata: handle broken cable reporting
One or two ancient drives predated the cable spec and didn't sent the
valid bits for the field. I had hoped to leave this out of libata as a
piece of historical annoyance but a recent CD drive shows the same bug so
we have to import support for it.

Same concept as Bartlomiej's changes old IDE except that as we have
centralised blacklists we can avoid keeping another private table of stuff

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-05 18:10:28 -05:00
Alan Cox
73946f9fc5 pata_hpt37x: Fix outstanding bug reports on the HPT374 and 37x cable detect
- Read frequency correctly
- Correct cable detect handling
- Fix wrong filter test

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-05 18:08:46 -05:00
Alan Cox
7f2803d026 ata_piix: Add additional PCI identifier for 40 wire short cable
Keeping the list in sync with the old IDE driver

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-05 18:08:46 -05:00