We currently turn interrupts back to their previous state before
calling do_page_fault(). This can be annoying when debugging as
a bad fault will potentially have lost some processor state before
getting into the debugger.
We also end up calling some generic code with interrupts enabled
such as notify_page_fault() with interrupts enabled, which could
be unexpected.
This changes our code to behave more like other architectures,
and make the assembly entry code call into do_page_faults() with
interrupts disabled. They are conditionally re-enabled from
within do_page_fault() in the same spot x86 does it.
While there, add the might_sleep() test in the case of a successful
trylock of the mmap semaphore, again like x86.
Also fix a bug in the existing assembly where r12 (_MSR) could get
clobbered by C calls (the DTL accounting in the exception common
macro and DISABLE_INTS) in some cases.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
v2. Add the r12 clobber fix
Some exceptions would unconditionally disable interrupts on entry,
which is fine, but calling lockdep every time not only adds more
overhead than strictly needed, but also means we get quite a few
"redudant" disable logged, which makes it hard to spot the really
bad ones.
So instead, split the macro used by the exception code into a
normal one and a separate one used when CONFIG_TRACE_IRQFLAGS is
enabled, and make the later skip th tracing if interrupts were
already disabled.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We unconditionally hard enable interrupts. This is unnecessary as
syscalls are expected to always be called with interrupts enabled.
While at it, we add a WARN_ON if that is not the case and
CONFIG_TRACE_IRQFLAGS is enabled (we don't want to add overhead
to the fast path when this is not set though).
Thus let's remove the enabling (and associated irq tracing) from
the syscall entry path. Also on Book3S, replace a few mfmsr
instructions with loads of PACAMSR from the PACA, which should be
faster & schedule better.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This moves the inlines into system.h and changes the runlatch
code to use the thread local flags (non-atomic) rather than
the TIF flags (atomic) to keep track of the latch state.
The code to turn it back on in an asynchronous interrupt is
now simplified and partially inlined.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The perfmon interrupt is the sole user of a special variant of the
interrupt prolog which differs from the one used by external and timer
interrupts in that it saves the non-volatile GPRs and doesn't turn the
runlatch on.
The former is unnecessary and the later is arguably incorrect, so
let's clean that up by using the same prolog. While at it we rename
that prolog to use the _ASYNC prefix.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This removes the various bits of assembly in the kernel entry,
exception handling and SLB management code that were specific
to running under the legacy iSeries hypervisor which is no
longer supported.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This cleans up vio.c after the removal of the legacy iSeries platform.
It also removes some no longer referenced include files.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PowerPC legacy iSeries plateform is being removed along with the
"one looney iseries driver", so this code can now be removed as well.
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PowerPC legacy iSeries platform is being removed so this is no
longer selectable.
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PowerPC legacy iSeries platform is being removed, so this code is no
longer needed.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PowerPC legacy iSeries platform is being removed and this code is
no longer selectable. There is more clean up that can be done, but this
just gets the old code out of the way.
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: Brian King <brking@linux.vnet.ibm.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This driver is specific to the PowerPC legcay iSeries platform which is
being removed.
Cc: David Miller <davem@davemloft.net>
Cc: <netdev@vger.kernel.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
- Use memchr_inv to check if the data contains all 0xFF bytes.
It is faster than looping for each byte.
- Use memcmp to compare memory areas
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
All IRQs on powerpc are managed via irq_domain anyway, there isn't really
any advantage to turning SPARSE_IRQ off, and it's the direction we want
to take the kernel design anyway. This patch makes powerpc always use
SPARSE_IRQ.
On pseries_defconfig, SPARSE_IRQ adds only about 0x300 bytes to the
.text sections, and removes about 0x20000 from the data section for the
static irq_desc table.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Ben Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On a 16TB system (using AMS/CMO), I get:
WARNING: ignoring large property [/ibm,dynamic-reconfiguration-memory] ibm,dynamic-memory length 0x000000000017ffec
and significantly less memory is thus shown to the partition. As far as
I can tell, the constant used is arbitrary. Ben Herrenschmidt provided
additional background that
> The limit was originally set because of Apple machines carrying ROM
> images in the device-tree, at a time where we were much more memory
> constrained than we are now.
and that it is likely not very useful any longer.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As described in e6fa16ab ("signal: sigprocmask() should do
retarget_shared_pending()") the modification of current->blocked is
incorrect as we need to check whether the signal we're about to block
is pending in the shared queue.
Also, use the new helper function introduced in commit 5e6292c0f2
("signal: add block_sigmask() for adding sigmask to current->blocked")
which centralises the code for updating current->blocked after
successfully delivering a signal and reduces the amount of duplicate
code across architectures. In the past some architectures got this
code wrong, so using this helper function should stop that from
happening again.
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Emit the function name not the address when possible.
builtin_return_address() gives an address. When building
a kernel with CONFIG_KALLSYMS, emit the actual function
name not the address.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There is a race where a thread causes a coprocessor type to be valid
in its own ACOP _and_ in the current context, but it does not
propagate to the ACOP register of other threads in time for them to
use it. The original code tries to solve this by sending an IPI to
all threads on the system, which is heavy handed, but unfortunately
still provides a window where the icswx is issued by other threads and
the ACOP is not up to date.
This patch detects that the ACOP DSI fault was a "false positive" and
syncs the ACOP and causes the icswx to be replayed.
Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Implement atomic_inc_not_zero and atomic64_inc_not_zero. At the
moment we use atomic*_add_unless which requires us to put 0 and
1 constants into registers. We can also avoid a subtract by
saving the original value in a second temporary.
This removes 3 instructions from fget:
- c0000000001b63c0: 39 00 00 00 li r8,0
- c0000000001b63c4: 39 40 00 01 li r10,1
...
- c0000000001b63e8: 7c 0a 00 50 subf r0,r10,r0
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We want to implement a ppc64 specific version of atomic_inc_not_zero
so wrap it in an ifdef to allow it to be overridden.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When the system is under heavy load, we occasionally saw a problem where
the system would get a legitimate interrupt when they should be
disabled.
This was caused by the data_dma_cb() DMA callback unconditionally
re-enabling FPGA interrupts even when data dumping is disabled. When
data dumping was re-enabled, the irq handler would fire while a DMA was
in progress. The "BUG_ON(priv->inflight != NULL);" during the second
invocation of the DMA callback caused the system to crash.
To fix the issue, the priv->enabled boolean is moved under the
protection of the priv->lock spinlock. The DMA callback checks the
boolean to know whether to re-enable FPGA interrupts before it returns.
Now that it is fixed, the driver keeps FPGA interrupts disabled when it
expects that they are disabled, fixing the bug.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Lockdep occasionally complains with the message:
INFO: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected
This is caused by calling videobuf_dma_unmap() under spin_lock_irq(). To
fix the warning, we drop the lock before unmapping and freeing the
buffer.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix typo "unsuported" to "unsupported" in
drivers/machintosh/mediabay.c
Signed-off-by: Masanari Iida<standby24x7@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/platforms/powernv/setup.c: included 'asm/xics.h' twice,
remove the duplicate.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/kvm/book3s_hv.c: included 'linux/sched.h' twice,
remove the duplicate.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
After this, we can remove the legacy iSeries code more easily.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When using a multi-ISU MPIC, we can interrupts up to
isu_size * MPIC_MAX_ISU, not just isu_size, so allocate
the right size reverse map.
Without this, the code will constantly fallback to
a linear search.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
1) ICMP sockets leave err uninitialized but we try to return it for the
unsupported MSG_OOB case, reported by Dave Jones.
2) Add new Zaurus device ID entries, from Dave Jones.
3) Pointer calculation in hso driver memset is wrong, from Dan
Carpenter.
4) ks8851_probe() checks unsigned value as negative, fix also from Dan
Carpenter.
5) Fix crashes in atl1c driver due to TX queue handling, from Eric
Dumazet. I anticipate some TX side locking fixes coming in the near
future for this driver as well.
6) The inline directive fix in Bluetooth which was breaking the build
only with very new versions of GCC, from Johan Hedberg.
7) Fix crashes in the ATP CLIP code due to ARP cleanups this merge
window, reported by Meelis Roos and fixed by Eric Dumazet.
8) JME driver doesn't flush RX FIFO correctly, from Guo-Fu Tseng.
9) Some ip6_route_output() callers test the return value for NULL, but
this never happens as the convention is to return a dst entry with
dst->error set. Fixes from RonQing Li.
10) Logitech Harmony 900 should be handled by zaurus driver not
cdc_ether, update white lists and black lists accordingly. From
Scott Talbert.
11) Receiving from certain kinds of devices there won't be a MAC header,
so there is no MAC header to fixup in the IPSEC code, and if we try
to do it we'll crash. Fix from Eric Dumazet.
12) Port type array indexing off-by-one in mlx4 driver, fix from Yevgeny
Petrilin.
13) Fix regression in link-down handling in davinci_emac which causes
all RX descriptors to be freed up and therefore RX to wedge
completely, from Christian Riesch.
14) It took two attempts, but ctnetlink soft lockups seem to be
cured now, from Pablo Neira Ayuso.
15) Endianness bug fix in ENIC driver, from Santosh Nayak.
16) The long ago conversion of the PPP fragmentation code over to
abstracted SKB list handling wasn't perfect, once we get an
out of sequence SKB we don't flush the rest of them like we
should. From Ben McKeegan.
17) Fix regression of ->ip_summed initialization in sfc driver.
From Ben Hutchings.
18) Bluetooth timeout mistakenly using msecs instead of jiffies,
from Andrzej Kaczmarek.
19) Using _sync variant of work cancellation results in deadlocks,
use the non _sync variants instead. From Andre Guedes.
20) Bluetooth rfcomm code had reference counting problems leading
to crashes, fix from Octavian Purdila.
21) The conversion of netem over to classful qdisc handling added
two bugs to netem_dequeue(), fixes from Eric Dumazet.
22) Missing pci_iounmap() in ATM Solos driver. Fix from Julia Lawall.
23) b44_pci_exit() should not have __exit tag since it's invoked from
non-__exit code. From Nikola Pajkovsky.
24) The conversion of the neighbour hash tables over to RCU added a
race, fixed here by adding the necessary reread of tbl->nht, fix
from Michel Machado.
25) When we added VF (virtual function) attributes for network device
dumps, this potentially bloats up the size of the dump of one
network device such that the dump size is too large for the buffer
allocated by properly written netlink applications.
In particular, if you add 255 VFs to a network device, parts of
GLIBC stop working.
To fix this, we add an attribute that is used to turn on these
extended portions of the network device dump. Sophisticaed
applications like 'ip' that want to see this stuff will be changed
to set the attribute, whereas things like GLIBC that don't care
about VFs simply will not, and therefore won't be busted by the
mere presence of VFs on a network device.
Thanks to the tireless work of Greg Rose on this fix.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (53 commits)
sfc: Fix assignment of ip_summed for pre-allocated skbs
ppp: fix 'ppp_mp_reconstruct bad seq' errors
enic: Fix endianness bug.
gre: fix spelling in comments
netfilter: ctnetlink: fix soft lockup when netlink adds new entries (v2)
Revert "netfilter: ctnetlink: fix soft lockup when netlink adds new entries"
davinci_emac: Do not free all rx dma descriptors during init
mlx4_core: Fixing array indexes when setting port types
phy: IC+101G and PHY_HAS_INTERRUPT flag
netdev/phy/icplus: Correct broken phy_init code
ipsec: be careful of non existing mac headers
Move Logitech Harmony 900 from cdc_ether to zaurus
hso: memsetting wrong data in hso_get_count()
netfilter: ip6_route_output() never returns NULL.
ethernet/broadcom: ip6_route_output() never returns NULL.
ipv6: ip6_route_output() never returns NULL.
jme: Fix FIFO flush issue
atm: clip: remove clip_tbl
ipv4: ping: Fix recvmsg MSG_OOB error handling.
rtnetlink: Fix problem with buffer allocation
...
The autofs compat handling fix caused a compile failure when
CONFIG_COMPAT isn't defined.
Instead of adding random #ifdef'fery in autofs, let's just make the
compat helpers earlier to use: without CONFIG_COMPAT, is_compat_task()
just hardcodes to zero.
We could probably do something similar for a number of other cases where
we have #ifdef's in code, but this is the low-hanging fruit.
Reported-and-tested-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQIcBAABAgAGBQJPR9QMAAoJEMsfJm/On5mBWbgP+wcJFIpqh84EyFGQuhSt61su
MQYcF8fWexSBzYjK5TB0nOougY/DQfTIBrqGf00Yr0RM81W3DlfbFNfl9tlBSwee
SEMBIm8qXALjWGb0eL3gy+Y8U10I2Pe0AvAvbiw3rjuJadqCLKljIQjQgwsuY0zY
yHwmeYgLTHVQfH8pk1n2QCFviqC4Lfd4Ltf/9EdQjm3WMxbJdLfHFnb99JvUt9Cu
b/NlXjeECZFLmX4P7JltdcfixbDUls9bPioFoldR8g5k1t/nCpnuUqPyj75zjQFk
D3WwzdA+YzH2nvoj0c+RjFBXYoHG7M/DFkKAy3ZF2cuRvxWP8QDK+WBbbOfA3HBF
YeefJp7hThRZVTkLCW+rG93PcUAIbOyX2tEk7DuaVlM9MyMjE/2SMqVw+AO6PBDS
4qXgfBrFmpVB6rapChD2M8RJsjbV5rw6eI3jM3+e2MJWDrCKgi13KHaCsUWTRFXI
l429vy809sdAx+8dTJK4KOIytFXDrrsw6tMPs9JQvcbLr2Bpn/4/jyUSyrZ0a7J4
ovfQtFk7y9NPHgjQmOswZm2yJPLwEJbuMUcwK3iIpelX8Y51ltMuVaQymKTeJAwi
+elRGK24q8C8wmRKT3mul4qSTmdvC+8nsAMD4/ozKsgDyO4oc9SYhf46mjCXzyn2
km0owCCnyoFWzS+w9lUJ
=YJz+
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Couple of minor driver fixes.
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (max34440) Fix resetting temperature history
hwmon: (f75375s) Fix register write order when setting fans to full speed
hwmon: (ads1015) Fix file leak in probe function
hwmon: (max6639) Fix PPR register initialization to set both channels
hwmon: (max6639) Fix FAN_FROM_REG calculation
three kbuild fixes for 3.3:
- make deb-pkg symlink race fix.
- make coccicheck fix.
- Dropping the check for modutils. This is not a regression, but
allows the module-init-tools replacement kmod work with the 3.3
kernel.
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
coccicheck: change handling of C={1,2} when M= is set
builddeb: Don't create files in /tmp with predictable names
kbuild: do not check for ancient modutils tools
When the autofs protocol version 5 packet type was added in commit
5c0a32fc2c ("autofs4: add new packet type for v5 communications"), it
obvously tried quite hard to be word-size agnostic, and uses explicitly
sized fields that are all correctly aligned.
However, with the final "char name[NAME_MAX+1]" array at the end, the
actual size of the structure ends up being not very well defined:
because the struct isn't marked 'packed', doing a "sizeof()" on it will
align the size of the struct up to the biggest alignment of the members
it has.
And despite all the members being the same, the alignment of them is
different: a "__u64" has 4-byte alignment on x86-32, but native 8-byte
alignment on x86-64. And while 'NAME_MAX+1' ends up being a nice round
number (256), the name[] array starts out a 4-byte aligned.
End result: the "packed" size of the structure is 300 bytes: 4-byte, but
not 8-byte aligned.
As a result, despite all the fields being in the same place on all
architectures, sizeof() will round up that size to 304 bytes on
architectures that have 8-byte alignment for u64.
Note that this is *not* a problem for 32-bit compat mode on POWER, since
there __u64 is 8-byte aligned even in 32-bit mode. But on x86, 32-bit
and 64-bit alignment is different for 64-bit entities, and as a result
the structure that has exactly the same layout has different sizes.
So on x86-64, but no other architecture, we will just subtract 4 from
the size of the structure when running in a compat task. That way we
will write the properly sized packet that user mode expects.
Not pretty. Sadly, this very subtle, and unnecessary, size difference
has been encoded in user space that wants to read packets of *exactly*
the right size, and will refuse to touch anything else.
Reported-and-tested-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When pre-allocating skbs for received packets, we set ip_summed =
CHECKSUM_UNNCESSARY. We used to change it back to CHECKSUM_NONE when
the received packet had an incorrect checksum or unhandled protocol.
Commit bc8acf2c8c ('drivers/net: avoid
some skb->ip_summed initializations') mistakenly replaced the latter
assignment with a DEBUG-only assertion that ip_summed ==
CHECKSUM_NONE. This assertion is always false, but it seems no-one
has exercised this code path in a DEBUG build.
Fix this by moving our assignment of CHECKSUM_UNNECESSARY into
efx_rx_packet_gro().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPSByoAAoJEDeqqVYsXL0M3CAIAJT740lwOyc9hyIBarZiZcZj
Ib9rPPppThKYvbo8w6Q6xITNTocohSnmPnjbfXZzN4nLrp1Xbzi6A4YLSeY3oxwE
t11LOMnXYPgCOCNZA3iJ4WadVbfs4Id6PWWZPnifWl6rZ2mhvtWmkCNzayY0Kv2t
WuX0j8ds0KgDG6xpfXKoXvHeNuEDJ5aZF/gtI1kmo1eilwPjlovCjsEWetHr/FQA
0jIKFdgf/nZ1ENZU0ztqGd/Q3er6t7G9qS7cFxUa4fWsqG+8Kl+KIk2PHDLL1QHu
tlYtaGm5kbh5d2tfzAD4HJZqJRw2LQ6U1gqofoAKS7JbqYPUJZDoERQtWZUpoj4=
=GZJg
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6
SCSI fixes on 20120224:
"This is a set of assorted bug fixes for power management, mpt2sas,
ipr, the rdac device handler and quite a big chunk for qla2xxx (plus a
use after free of scsi_host in scsi_scan.c). "
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] scsi_dh_rdac: Fix for unbalanced reference count
[SCSI] scsi_pm: Fix bug in the SCSI power management handler
[SCSI] scsi_scan: Fix 'Poison overwritten' warning caused by using freed 'shost'
[SCSI] qla2xxx: Update version number to 8.03.07.13-k.
[SCSI] qla2xxx: Proper detection of firmware abort error code for ISP82xx.
[SCSI] qla2xxx: Remove resetting memory during device initialization for ISP82xx.
[SCSI] qla2xxx: Complete mailbox command timedout to avoid initialization failures during next reset cycle.
[SCSI] qla2xxx: Remove check for null fcport from host reset handler.
[SCSI] qla2xxx: Correct out of bounds read of ISP2200 mailbox registers.
[SCSI] qla2xxx: Remove errant clearing of MBX_INTERRUPT flag during CT-IOCB processing.
[SCSI] qla2xxx: Clear options-flags while issuing stop-firmware mbx command.
[SCSI] qla2xxx: Add an "is reset active" helper.
[SCSI] qla2xxx: Add check for null fcport references in qla2xxx_queuecommand.
[SCSI] qla2xxx: Propagate up abort failures.
[SCSI] isci: Fix NULL ptr dereference when no firmware is being loaded
[SCSI] ipr: fix eeh recovery for 64-bit adapters
[SCSI] mpt2sas: Fix mismatch in mpt2sas_base_hard_reset_handler() mutex lock-unlock
This patch fixes a (mostly cosmetic) bug introduced by the patch
'ppp: Use SKB queue abstraction interfaces in fragment processing'
found here: http://www.spinics.net/lists/netdev/msg153312.html
The above patch rewrote and moved the code responsible for cleaning
up discarded fragments but the new code does not catch every case
where this is necessary. This results in some discarded fragments
remaining in the queue, and triggering a 'bad seq' error on the
subsequent call to ppp_mp_reconstruct. Fragments are discarded
whenever other fragments of the same frame have been lost.
This can generate a lot of unwanted and misleading log messages.
This patch also adds additional detail to the debug logging to
make it clearer which fragments were lost and which other fragments
were discarded as a result of losses. (Run pppd with 'kdebug 1'
option to enable debug logging.)
Signed-off-by: Ben McKeegan <ben@netservers.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reverts a portion of d0bc1fb4 so that coccicheck will
work properly when C=1 or C=2.
Reported-and-tested-by: Brice Goglin <Brice.Goglin@inria.fr>
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Michal Marek <mmarek@suse.cz>
The original spelling and bad word choice makes these comments hard to read.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] hdpvr: update picture controls to support firmware versions > 0.15
[media] wl128x: fix build errors when GPIOLIB is not enabled
[media] hdpvr: fix race conditon during start of streaming
[media] omap3isp: Fix crash caused by subdevs now having a pointer to devnodes
[media] imon: don't wedge hardware after early callbacks
signalfd_cleanup() ensures that ->signalfd_wqh is not used, but
this is not enough. eppoll_entry->whead still points to the memory
we are going to free, ep_unregister_pollwait()->remove_wait_queue()
is obviously unsafe.
Change ep_poll_callback(POLLFREE) to set eppoll_entry->whead = NULL,
change ep_unregister_pollwait() to check pwq->whead != NULL under
rcu_read_lock() before remove_wait_queue(). We add the new helper,
ep_remove_wait_queue(), for this.
This works because sighand_cachep is SLAB_DESTROY_BY_RCU and because
->signalfd_wqh is initialized in sighand_ctor(), not in copy_sighand.
ep_unregister_pollwait()->remove_wait_queue() can play with already
freed and potentially reused ->sighand, but this is fine. This memory
must have the valid ->signalfd_wqh until rcu_read_unlock().
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Cc: <stable@kernel.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is intentionally incomplete to simplify the review.
It ignores ep_unregister_pollwait() which plays with the same wqh.
See the next change.
epoll assumes that the EPOLL_CTL_ADD'ed file controls everything
f_op->poll() needs. In particular it assumes that the wait queue
can't go away until eventpoll_release(). This is not true in case
of signalfd, the task which does EPOLL_CTL_ADD uses its ->sighand
which is not connected to the file.
This patch adds the special event, POLLFREE, currently only for
epoll. It expects that init_poll_funcptr()'ed hook should do the
necessary cleanup. Perhaps it should be defined as EPOLLFREE in
eventpoll.
__cleanup_sighand() is changed to do wake_up_poll(POLLFREE) if
->signalfd_wqh is not empty, we add the new signalfd_cleanup()
helper.
ep_poll_callback(POLLFREE) simply does list_del_init(task_list).
This make this poll entry inconsistent, but we don't care. If you
share epoll fd which contains our sigfd with another process you
should blame yourself. signalfd is "really special". I simply do
not know how we can define the "right" semantics if it used with
epoll.
The main problem is, epoll calls signalfd_poll() once to establish
the connection with the wait queue, after that signalfd_poll(NULL)
returns the different/inconsistent results depending on who does
EPOLL_CTL_MOD/signalfd_read/etc. IOW: apart from sigmask, signalfd
has nothing to do with the file, it works with the current thread.
In short: this patch is the hack which tries to fix the symptoms.
It also assumes that nobody can take tasklist_lock under epoll
locks, this seems to be true.
Note:
- we do not have wake_up_all_poll() but wake_up_poll()
is fine, poll/epoll doesn't use WQ_FLAG_EXCLUSIVE.
- signalfd_cleanup() uses POLLHUP along with POLLFREE,
we need a couple of simple changes in eventpoll.c to
make sure it can't be "lost".
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Cc: <stable@kernel.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Quoth Chris:
"This is later than I wanted because I got backed up running through
btrfs bugs from the Oracle QA teams. But they are all bug fixes that
we've queued and tested since rc1.
Nothing in particular stands out, this just reflects bug fixing and QA
done in parallel by all the btrfs developers. The most user visible
of these is:
Btrfs: clear the extent uptodate bits during parent transid failures
Because that helps deal with out of date drives (say an iscsi disk
that has gone away and come back). The old code wasn't always
properly retrying the other mirror for this type of failure."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (24 commits)
Btrfs: fix compiler warnings on 32 bit systems
Btrfs: increase the global block reserve estimates
Btrfs: clear the extent uptodate bits during parent transid failures
Btrfs: add extra sanity checks on the path names in btrfs_mksubvol
Btrfs: make sure we update latest_bdev
Btrfs: improve error handling for btrfs_insert_dir_item callers
Btrfs: be less strict on finding next node in clear_extent_bit
Btrfs: fix a bug on overcommit stuff
Btrfs: kick out redundant stuff in convert_extent_bit
Btrfs: skip states when they does not contain bits to clear
Btrfs: check return value of lookup_extent_mapping() correctly
Btrfs: fix deadlock on page lock when doing auto-defragment
Btrfs: fix return value check of extent_io_ops
btrfs: honor umask when creating subvol root
btrfs: silence warning in raid array setup
btrfs: fix structs where bitfields and spinlock/atomic share 8B word
btrfs: delalloc for page dirtied out-of-band in fixup worker
Btrfs: fix memory leak in load_free_space_cache()
btrfs: don't check DUP chunks twice
Btrfs: fix trim 0 bytes after a device delete
...
which was dropped because c6x had not yet been merged at the time.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=YDuM
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://linux-c6x.org/git/projects/linux-c6x-upstreaming
This is the arch/c6x part of commit 7c43185138 ("Kbuild: Use dtc's -d
(dependency) option") which was dropped because c6x had not yet been
merged at the time.
* tag 'for-linus' of git://linux-c6x.org/git/projects/linux-c6x-upstreaming:
Kbuild: Use dtc's -d (dependency) option
I don't even live in the same country as any of my PA-RISC hardware
these days, so the odds of me touching the code are pretty low.
(Also re-order things to ensure jejb gets CC'd since he's been the
primary maintainer for the last few years.)
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
