Commit Graph

3 Commits

Author SHA1 Message Date
Peter Tyser
cc604ddd11 USB: ehci-fsl: Fix 'have_sysif_regs' detection
Previously a check was done on an ID register at the base of a CPU's
internal USB registers to determine if system interface regsiters were
present.  The check looked for an ID register that had the format
ID[0:5] == ~ID[8:13] as described in the MPC5121 User's Manual to
determine if a MPC5121 or MPC83xx/85xx was being used.

There are two issues with this method:
- The ID register is not defined on the MPC83xx/85xx CPUs, so its
  unclear what is being checked on them.
- Newer CPUs such as the P4080 also don't document the ID register, but
  do share the same format as the MPC5121.  Thus the previous code did
  not set 'have_sysif_regs' properly which results in the P4080 not
  properly initializing its USB ports.

Using the device tree 'compatible' node is a cleaner way to determine if
'have_sysif_regs' should be set and resolves the USB initialization issue
seen on the P4080.

Tested on a P4080-based system and compile tested on mpc512x_defconfig
with Freescale EHCI driver enabled.

Cc: Anatolij Gustschin <agust@denx.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-01-22 18:38:58 -08:00
Anatolij Gustschin
230f7ede6c USB: add USB EHCI support for MPC5121 SoC
Extends FSL EHCI platform driver glue layer to support
MPC5121 USB controllers. MPC5121 Rev 2.0 silicon EHCI
registers are in big endian format. The appropriate flags
are set using the information in the platform data structure.
MPC83xx system interface registers are not available on
MPC512x, so the access to these registers is isolated in
MPC512x case. Furthermore the USB controller clocks
must be enabled before 512x register accesses which is
done by providing platform specific init callback.

The MPC512x internal USB PHY doesn't provide supply voltage.
For boards using different power switches allow specifying
DRVVBUS and PWR_FAULT signal polarity of the MPC5121 internal
PHY using "fsl,invert-drvvbus" and "fsl,invert-pwr-fault"
properties in the device tree USB nodes. Adds documentation
for this new device tree bindings.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22 10:21:58 -07:00
Anatolij Gustschin
126512e3f2 USB: add platform glue driver for FSL USB DR controller
Replace FSL USB platform code by simple platform driver for
creation of FSL USB platform devices.

The driver creates platform devices based on the information
from USB nodes in the flat device tree. This is the replacement
for old arch fsl_soc usb code removed by this patch. The driver
uses usual of-style binding, available EHCI-HCD and UDC
drivers can be bound to the created devices. The new of-style
driver additionaly instantiates USB OTG platform device, as the
appropriate USB OTG driver will be added soon.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22 10:21:58 -07:00