Commit Graph

1269 Commits

Author SHA1 Message Date
Linus Torvalds
0191b625ca Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
  net: Allow dependancies of FDDI & Tokenring to be modular.
  igb: Fix build warning when DCA is disabled.
  net: Fix warning fallout from recent NAPI interface changes.
  gro: Fix potential use after free
  sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
  sfc: When disabling the NIC, close the device rather than unregistering it
  sfc: SFT9001: Add cable diagnostics
  sfc: Add support for multiple PHY self-tests
  sfc: Merge top-level functions for self-tests
  sfc: Clean up PHY mode management in loopback self-test
  sfc: Fix unreliable link detection in some loopback modes
  sfc: Generate unique names for per-NIC workqueues
  802.3ad: use standard ethhdr instead of ad_header
  802.3ad: generalize out mac address initializer
  802.3ad: initialize ports LACPDU from const initializer
  802.3ad: remove typedef around ad_system
  802.3ad: turn ports is_individual into a bool
  802.3ad: turn ports is_enabled into a bool
  802.3ad: make ntt bool
  ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
  ...

Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
2008-12-28 12:49:40 -08:00
Peter Tiedemann
2a7c6f2c39 [S390] convert ctcm printks to dev_xxx and pr_xxx macros.
Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:27 +01:00
Christof Schmitt
ecf39d4212 [S390] convert zfcp printks to pr_xxx macros.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:27 +01:00
Martin Schwidefsky
5466c2e43e [S390] convert vmlogrdr printks to pr_xxx macros.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:26 +01:00
Michael Holzheu
17159dc6fb [S390] convert zfcp dumper printks to pr_xxx macros.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:26 +01:00
Frank Blaschka
74eacdb9c2 [S390] convert qeth printks to dev_xxx and pr_xxx macros.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:25 +01:00
Martin Schwidefsky
b3ff088b30 [S390] convert sclp printks to pr_xxx macros.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:24 +01:00
Ursula Braun
8f7c502c26 [S390] convert iucv printks to dev_xxx and pr_xxx macros.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:24 +01:00
Martin Schwidefsky
136f7a1c42 [S390] convert ap_bus printks to pr_xxx macros.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:24 +01:00
Hongjie Yang
93098bf015 [S390] convert dcssblk and extmem printks messages to pr_xxx macros.
Signed-off-by: Hongjie Yang <hongjie@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:23 +01:00
Melissa Howland
1519c0c6eb [S390] convert monwriter printks to pr_xxx macros.
Signed-off-by: Melissa Howland <melissah@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:23 +01:00
Gerald Schaefer
a4f5a299cf [S390] convert monreader printks to pr_xxx macros.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:22 +01:00
Michael Ernst
e6d5a428e0 [S390] convert cio printks to pr_xxx macros.
Signed-off-by: Michael Ernst <mernst@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:20 +01:00
Frank Munzert
80a5c36d1d [S390] convert vmur printks to pr_xxx macros.
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:19 +01:00
Klaus-D. Wacker
c99fc5dadc [S390] convert lcs printks to dev_xxx and pr_xxx macros.
Signed-off-by: Klaus-D. Wacker <kdwacker@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:18 +01:00
Christian Borntraeger
8988e58f8b [S390] convert vmcp printks to pr_xxx macros.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:18 +01:00
Martin Schwidefsky
d1c2f8928a [S390] convert xpram printks to pr_xxx macros.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:18 +01:00
Julia Lawall
acfa922c5a [S390] s390: Remove redundant test
The loop above the modified code only terminates when rc is a valid pointer.

A simplified version of the semantic patch that makes this change is as
follows: (http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r exists@
local idexpression x;
expression E;
position p1,p2;
@@

if (x@p1 == NULL || ...) { ... when forall
   return ...; }
... when != \(x=E\|x--\|x++\|--x\|++x\|x-=E\|x+=E\|x|=E\|x&=E\|&x\)
(
x@p2 == NULL
|
x@p2 != NULL
)

// another path to the test that is not through p1?
@s exists@
local idexpression r.x;
position r.p1,r.p2;
@@

... when != x@p1
(
x@p2 == NULL
|
x@p2 != NULL
)

@fix depends on !s@
position r.p1,r.p2;
expression x,E;
statement S1,S2;
@@

(
- if ((x@p2 != NULL) || ...)
  S1
|
- if ((x@p2 == NULL) && ...) S1
|
- BUG_ON(x@p2 == NULL);
)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:17 +01:00
Julia Lawall
21e7b2c4d5 [S390] drivers/s390/crypto: Move dereference to after IS_ERR test
If reply is ERR_PTR(...), then it should not be dereferenced, so I have
moved the dereference from the declaration to after the IS_ERR test.

The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@match exists@
expression x, E;
identifier fld;
position p1,p2;
@@

(
x = E;
|
x = E
|
x@p1->fld
... when != x = E
IS_ERR(x@p2)
... when any
)

@other_match exists@
expression match.x, E1, E2;
position match.p1,match.p2;
@@

x = E1
... when != x = E2
    when != x@p1
x@p2

@ script:python depends on !other_match@
p1 << match.p1;
p2 << match.p2;
@@

print "* file %s dereference %s test %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:16 +01:00
Heiko Carstens
b3b59d3339 [S390] sclp vt220: fix compile warning
get rid of this one:

  CC      drivers/s390/char/sclp_vt220.o
drivers/s390/char/sclp_vt220.c:588: warning: '__sclp_vt220_flush_buffer' defined but not used

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:12 +01:00
Sebastian Ott
d36f0c6638 [S390] cio: use pim to check for multipath.
To check if multipath is available we count the bits set in lpm,
which could change over time (via configure [on|off] of a path).

The following patch uses the pim (which is persistent) for this
decision.

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:11 +01:00
Sebastian Ott
f444cc0e52 [S390] cio: commit all pmcw changes.
Sometimes we change the pmcw configuration but don't call msch
to transmit these changes to the channel subsystem.

The patch fixes this by calling cio_commit_config in such cases.

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:10 +01:00
Sebastian Ott
13952ec12d [S390] cio: introduce cio_commit_config
To change the configuration of a subchannel we alter the modifiable
bits of the subchannel's schib field and issue a modify subchannel.
There can be the case that not all changes were applied -or worse-
quietly overwritten by the hardware. With the next store subchannel
we obtain the current state of the hardware but lose our target
configuration.

With this patch we introduce a subchannel_config structure which
contains the target subchannel configuration. Additionally the msch
wrapper cio_modify is replaced with cio_commit_config which
copies the desired changes to a temporary schib. msch is then
called with the temporary schib. This schib is only written back
to the subchannel if all changes were applied.

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:10 +01:00
Sebastian Ott
cdb912a40d [S390] cio: introduce cio_update_schib
There is the chance that we get condition code 0 for a stsch but
the resulting schib is not vaild. In the current code there are
2 cases:
* we do a check for validity of the schib after stsch, but at this
  time we have already stored the invaild schib in the subchannel
  structure. This may lead to problems.
* we don't do a check for validity, which is not that good either.

The patch addresses both issues by introducing the stsch wrapper
cio_update_schib which performs stsch on a local schib. This schib
is only written back to the subchannel if it's valid.

side note: For some functions (chp_events) the return codes are
different now (-ENXIO vs -ENODEV) but this shouldn't do harm
since the caller doesn't check for _specific_ errors.

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:10 +01:00
Cornelia Huck
d6a30761d8 [S390] cio: Use device_is_registered().
Check if a ccw device is registered via device_is_registered()
and not via the old kludge of checking the membership in driver
core internal klists.

Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:09 +01:00
Cornelia Huck
283fdd0b8a [S390] cio: Dont call ->release directly.
Just put the cdev's reference count to give up our reference.

Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:09 +01:00
Cornelia Huck
90ed2b692f [S390] cio: Dont fail probe for I/O subchannels.
If we fail the probe for an I/O subchannel, we won't be able
to unregister it again since there are no sch_event()
callbacks for unbound subchannels. Just succeed the probe in
any case and schedule unregistering the subchannel.

Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:08 +01:00
Cornelia Huck
5fb6b8544d [S390] cio: Only register ccw_device for registered subchannel.
There is a race between io_subchannel_register() and
io_subchannel_sch_event() which may cause a subchannel to be
unregistered because it is no longer operational before
io_subchannel_register() had run. We need to check whether the
subchannel is still registered before the ccw device can be
registered and just bail out if it is not.

Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:08 +01:00
Cornelia Huck
6eff208f47 [S390] cio: Fix I/O subchannel refcounting.
Subchannel refcounting was incorrect in some places, especially
a refcount was missing when ccw_device_call_sch_unregister()
was called and the refcount was not correctly switched after
moving devices.

Fix this by establishing the following rules:
- The ccw_device obtains a reference on its parent subchannel
  when dev.parent is set and gives it up in its release
  function. This is needed because we need a parent reference
  for correct refcounting even before the ccw device is (if at
  all) registered.
- When calling device_move(), obtain a reference on the new
  subchannel before moving the ccw device and give up the
  reference on the old parent after moving. This brings the
  refcount in line with the first rule.

Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:08 +01:00
Cornelia Huck
9cd6742197 [S390] cio: Fix reference counting for online/offline.
The current code attempts to get an extra reference count
for online devices by doing a get_device() in ccw_device_online()
and a put_device() in ccw_device_done(). However, this
- incorrectly obtains an extra reference for disconnected
  devices becoming available again (since they are already
  online)
- needs special checks for css_init_done in order to handle
  the console device
- is not obvious and
- may incorretly drop a reference count in ccw_device_done() if
  that function is called after path verification for a device
  that just became not operational.

So let's just get the reference in ccw_device_set_online() and
drop it in ccw_device_set_offline(). (Unfortunately, we still
need the special case in io_subchannel_probe().)

Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:07 +01:00
Cornelia Huck
97166f52fc [S390] cio: Put referernce on correct device after moving.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:07 +01:00
Peter Oberparleiter
c619d4223e [S390] cio: fix ccwgroup online vs. ungroup race condition
Ensure atomicity of ungroup operation to prevent concurrent ungroup
and online processing which may lead to use-after-release situations.

Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:06 +01:00
Sebastian Ott
111e95a4ca [S390] cio: move irritating comment.
Due to former patches a comment and device id initialization were
split from the addressed function call in io_subchannel_probe.

Move it back to where it belongs.

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:06 +01:00
Heiko Carstens
191fd44c11 [S390] cio: get rid of compile warning
Move cio_tpi() to the rest of the CONFIG_CCW_CONSOLE functions to
get rid of this one:

drivers/s390/cio/cio.c:115: warning: 'cio_tpi' defined but not used

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:05 +01:00
Kay Sievers
98df67b324 [S390] struct device - replace bus_id with dev_name(), dev_set_name()
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:03 +01:00
Stefan Haberland
0cd4bd4754 [S390] dasd: call cleanup_cqr with request_queue_lock
__dasd_cleanup_cqr should be called with request_queue_lock held and
__dasd_block_process_erp with queue_lock

Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:02 +01:00
Stefan Haberland
50afd20f8c [S390] dasd: correct sense byte condition for SIM
SIM sense data are always 32 bit sense data so sense byte 27 bit 0
has not to be set.

Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:02 +01:00
Cornelia Huck
faf16aa9b3 [S390] dasd: Use accessors instead of using driver_data directly.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:01 +01:00
Stefan Haberland
2bf373b3e3 [S390] dasd: improve dasd statistics proc interface
For a large number of I/O requests the values were shifted binary.
The shift was not transparent for the user because the shift value
was not displayed. To make this interface more human readable the
values are shifted decimal and the scale factor is displayed.

Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:01 +01:00
Christof Schmitt
bd43a42b7e [S390] zfcp: Report microcode level through service level interface
Register zfcp with the new /proc/service_level interface to report the
FCP microcode level. When the adapter goes offline or a channel path
disappears, zfcp unregisters, since the microcode version might change
and zfcp does not know about it.

Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:01 +01:00
Martin Schwidefsky
6bcac508fb [S390] service level interface.
Add a new proc interface /proc/service_levels that allows any code
to report a relevant service level, e.g. the microcode level of
devices, the service level of the hypervisor, etc.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:00 +01:00
Jan Glauber
7a0b4cbc7d [S390] qdio: fix error reporting for hipersockets
Hipersocket connections can encounter temporary busy conditions.
In case of the busy bit set we retry the SIGA operation immediatelly.
If the busy condition still persists after 100 ms we fail and report
the error to the upper layer. The second stage retry logic is removed.
In case of ongoing busy conditions the upper layer needs to reset the
connection.

The reporting of a SIGA error is now done synchronously to allow the
network driver to requeue the buffers. Also no error trace is created
for the temporary SIGA errors so the error message view is not flooded.

Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:39:00 +01:00
Jan Glauber
50f769df1c [S390] qdio: improve inbound buffer acknowledgement
- Use automatic acknowledgement of incoming buffers in QEBSM mode
- Move ACK for non-QEBSM mode always to the newest buffer to prevent
  a race with qdio_stop_polling
- Remove the polling spinlock, the upper layer drivers return new buffers
  in the same code path and could not run in parallel
- Don't flood the error log in case of no-target-buffer-empty
- In handle_inbound we check if we would overwrite an ACK'ed buffer, if so
  advance the pointer to the oldest ACK'ed buffer so we don't overwrite an
  empty buffer in qdio_stop_polling

Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:38:59 +01:00
Jan Glauber
22f9934767 [S390] qdio: rework debug feature logging
- make qdio_trace a per device view
- remove s390dbf exceptions
- remove CONFIG_QDIO_DEBUG, not needed anymore if we check for the level
  before calling sprintf
- use snprintf for dbf entries
- add start markers to see if the dbf view wrapped
- add a global error view for all queues

Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:38:59 +01:00
Jan Glauber
9a1ce28aeb [S390] qdio: fix compile warning under 31 bit
The QEBSM instructions are only available for CONFIG_64BIT, they are not
used under 31 bit. Make compiler happy about the false positive:

drivers/s390/cio/qdio_main.c: In function ?qdio_inbound_q_done?:
drivers/s390/cio/qdio_main.c:532: warning: ?state? may be used uninitialized in this function

Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:38:58 +01:00
Jan Glauber
23589d057a [S390] qdio: add eqbs/sqbs instruction counters
Add counters for the eqbs and sqbs instructions that indicate how often
we issued the instructions and how often the instructions returned with
less buffers than specified.

Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:38:58 +01:00
Jan Glauber
bbd50e172f [S390] qdio: fix qeth port count detection
qeth needs to get the port count information before
qdio has allocated a page for the chsc operation.
Extend qdio_get_ssqd_desc() to store the data in the
specified structure.

Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:38:58 +01:00
Christian Maaser
43c207e6e5 [S390] ap: Minor code beautification.
Changed some symbol names for a better and clearer code.

Signed-off-by: Christian Maaser <cmaaser@de.ibm.com>
Signed-off-by: Felix Beck <beckf@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:38:57 +01:00
Felix Beck
cb17a6364a [S390] zcrypt: Use of Thin Interrupts
When the machine supports AP adapter interrupts polling will be
switched off at module initialization and the driver will work in
interrupt mode.

Signed-off-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:38:57 +01:00
Christian Borntraeger
a114a9d69d [S390] vmcp: remove BKL
The vmcp driver uses the session->mutex for concurrent access of the data
structures. Therefore, the BKL in vmcp_open does not protect against any
other function in the driver.
The BLK in vmcp_open would protect concurrent access to the module init
but all necessary steps ave finished before misc_register is called.
We can safely remove the lock_kernel from vcmp.

Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:38:54 +01:00